User`s manual
Contents
1. IMAGE AUTO ADJUST Adjusts H V Position and Clock Phase automatically Only available for VGA input COLOR AUTO ADJUST Adjusts red green and blue colors gain automatically Only available for VGA input RESET Resets the display to its default values 15 MISC MENU HOTKEY TYPE d ECO DCR gt SIGNAL SOURCE 4 VGA gt AUDIO SELECT 4 ANALOG gt VOLUME Rn 50 HOTKEY TYPE Contains ECO DCR BRI CON and ASP ECO hotkey combinations UP and DOWN will be the hotkey buttons while OSD menu is not displayed SIGNAL SOURCE Selects the input source You can select VGA DVI HDMI and DP AUDIO SELECT Selects the audio input source Analog or Digital VOLUME Sets the volume level The adjustment range is 0 to 100 16 TECHNICAL SUPPORT Monoprice is pleased to provide free live online technical support to assist you with any questions you may have about installation setup troubleshooting or product recommendations If you ever need assistance with your new product please come online to talk to one of our friendly and knowledgeable Tech Support Associates Technical support is available through the online chat button on our website www monoprice com during regular business hours 7 days a week You can also get assistance through email by sending a message to tech monoprice com WARRANTY MONOPRICE will replace defective monitors with a new monitor if the RMA is issued within thirty 30 days of the original2. computer to the audio input on the monitor Plug the DC power connector on the AC power adapter into the DC IN port on the back of the monitor Plug the included AC power cord into the AC power adapter Plug the other end into a nearby power outlet MONITOR STAND amp BASE To install the stand perform the following steps 1 Place a blanket or towel on a flat surface such as a table or the floor 2 Place the monitor face down on the blanket or towel 3 Install the stand on the VESA mount using the four included M4x8screws 4 Fit the base on the bottom of the stand and press it until it clicks into place To remove the base perform the following steps 1 Place a blanket or towel on a flat surface such as a table or the floor 2 Place the monitor face down on the blanket or towel 3 Squeeze the plastic clip on the bottom of the base and pull the base off the stand Note that the stand can be removed from the back of the monitor so that the monitor can be attached to a desk or wall mount To remove the stand perform the following steps 1 Place a blanket or towel on a flat surface such as a table or the floor 2 Place the monitor face down on the blanket or towel 3 Remove the four M4x8screws attaching the stand to the back of the monitor 4 Follow the mounting instructions for your wall desk mount to attach the monitor to the mount 5 Store the stand and mount screws in a safe place for future
3. household waste Instead it is your responsibility to dispose of your waste equipment by arranging to return it to a designated collection point for the recycling of waste electrical and electronic equipment By separating and recycling your waste equipment at the time of disposal you will help to conserve natural resources and ensure that the equipment is recycled in a manner that protects human health and the environment ETL Compliance Statement This product has been thorough tested by Intertek ETL a nationally recognized independent third party testing laboratory The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U S and Canadian device safety standards that the manufacturing site has been audited and the that manufacturer has a agreed to a program of quarterly factory follow up inspections to verify continued conformance 20
4. or damaged please contact Monoprice Customer Service for a replacement 1x 27 WQHD LED monitor 1x Adjustable stand 1x Stand base 4x M4x8 stand mount screws 1x AC power adapter 1x AC power cord 1x 3 5mm TRS audio cable 1x Dual Link DVI D video cable 1x User s manual CONNECTIONS oc o Ho o 1 2 3 4 5 6 DP DisplayPort 1 2 video input Analog D Sub video input Dual Link DVI D video input HDMI HDMI video input 5 3 5mm TRS stereo audio input DVI Note This monitor features a Dual Link DVI D input port Your DVI source must support Dual Link DVI D and you must use a Dual Link DVI D cable included which has a pinout that looks like this CONTROLS T VOL VOL UP DOWN SELECT MENU d 1 2 3 4 a 6 f VOL If the OSD menu is displayed and an entry has been opened for editing pressing the VOL button increases the selected value If the OSD is not displayed pressing the VOL button opens the volume adjustment control With either the brightness or volume adjustment control displayed pressing the VOL button increases the brightness or volume VOL If the OSD menu is displayed and an entry has been opened for editing pressing the VOL button decreases the selected value If the OSD is not displayed pressing the VOL button opens the brightness adjustment control With either the brightness or volume adjustment control displayed pressing the VOL button decreases the brightness or volu
5. use Note The monitor uses a VESA mounting size of 100x100mm VIEWING ANGLE ADJUSTMENT The included monitor stand supports tilt adjustment from 5 down to 20 up To adjust the angle grasp the bezel at both the top and bottom of the monitor and move it as desired Use soft cloth gloves or a soft dry cloth to grasp the monitor without touching the screen MAIN INPUT SELECTION To change the main input perform the following steps 1 Press the SELECT button to display the Inout Selection menu 2 Use the UP or DOWN buttons to move the highlight to the desired input 3 Press the SELECT button to select the highlighted input VGA DVI HDMI DP ON SCREEN DISPLAY OSD MENU Press the MENU button to access the OSD menu Basic Menu Operation VOL When the OSD menu is displayed and an item has been opened for editing pressing the VOL button increases the selected value VOL When the OSD menu is displayed and an item has been opened for editing pressing the VOL button decreases the selected value UP When the OSD menu is displayed pressing the UP button moves the selection highlight up DOWN When the OSD menu is displayed pressing the DOWN button moves the selection highlight down SELECT When the OSD menu is displayed pressing the SELECT button either selects the currently highlighted menu option or opens the currently highlighted menu entry for editing If the OSD menu is not displayed pressi
6. E Reduces image noise by adjusting Phase The adjusting range is from 0 to 100 Only available for VGA input ASPECT Adjusts the aspect ratio to WIDE or 4 3 12 COLOR TEMP MENU COLOR TEMP RED GREEN BLUE COLOR TEMP Contains four color modes Warm Normal Cool and User RED The color of Red is user configurable the adjusting range is from 0 to 100 GREEN The color of Green is user configurable the adjusting range is from O to 100 BLUE The color of Blue is user configurable the adjusting range is from O to 100 13 OSD SETTING MENU OSD SETTING LANGUAGE OSD H POS OSD V POS OSD TIMER TRANSPARENCY LANGUAGE This menu allows you to set the language to be used in the OSD The possible options are English French Deutsche Italiano Espanol Nederlands OSD H POS Adjusts the horizontal position of the OSD menu The adjustment range is 0 to 100 OSD V POS Adjusts the vertical position of the OSD menu The adjustment range is 0 to 100 OSD Timer Sets the amount of time in seconds that the OSD menu will display without any input before it automatically closes The possible options are 5s 10s 15 20s 25s 30s 35s 40s 45s 50s 55s and 60s TRANSPARENCY Adjusts how transparent or opaque the OSD menu will appear on screen The possible options are 0 25 50 75 and 100 14 RESET MENU IMAGE AUTO ADJUST EA COLOR AUTO ADJUST RESET
7. Users Manual Pro LED Monitor WOQOHD Gei SPEAKER D I nmonorece CONTENTS SAFETY WARNINGS AND GUIDELINES i ea 2 ee 3 EE 4 PACKAGE EECH NR EE 4 BEE E ne 5 SEENEN EE 6 RE 7 MONITOR STAND EE 7 VIEWING ANGLE ADJUS TME CR RE 9 MAIN INPUT SELEC HON WEE 9 ON SCREEN DISPLAY OSD MENU een 10 Basic MENU OC e EE 10 BRIGEIENESS MEN Winsen en 11 JE IR 12 GOLOR TEMP MENU EE 13 OSDSEILING ME NU ee ee 14 RESET MENU E 15 MSO MENU ee E AS RES 16 TECRNICACSUPRPOR EE 17 WARRANTY serpen aaa eee 17 TROUBEESHOOTING zes an 18 SPE GIG an L 19 Breil el Eet ale ein Ee WE 20 SAFETY WARNINGS AND GUIDELINES Do not place the monitor on an unstable surface where it could fall and cause either personal injury or damage to the monitor and or other equipment Do not expose the monitor to water or moisture of any kind Do not place objects containing moisture such as a glass or vase where it could tip over and spill into or onto the monitor If the monitor is exposed to water or moisture immediately unplug it from its power source and allow it to completely dry out before reapplying power Do not block the ventilation holes in the monitor s casing Do not place the monitor in a confined space with inadequate ventilation Do not place the monitor near a heat source such as a fireplace heating vent radiator etc The power supply for this monitor uses a NEMA 5 15 three prong grounded plug Do not use a cheater plug or
8. date of purchase as shown on the original invoice Monitors identified as defective after 30 days but within the twelve 12 month warranty period will be replaced with refurbished reconditioned or used monitors at MONOPRICE S discretion All returned products are the property of MONOPRICE and must be returned to MONOPRICE for a replacement to be issued 17 TROUBLESHOOTING Following are some common problems and possible solutions If you cannot solve a problem yourself please contact Monoprice Technical Support for assistance Q The power LED is off A Verify that the power adapter is plugged into the monitor Verify that the power cord is plugged into both the AC adapter and the power outlet Verify that the power outlet is live by plugging something else into it such as a lamp Q The picture is weak washed out or over saturated A Adjust the Brightness and or Contrast Q The image flashes or distorts A Verify that there are no nearby sources or Radio Frequency or Electromagnetic Interference RFI or EMI Q The power LED is glowing blue but the display is blank A Press a key on the keyboard to ensure the computer is not asleep or that a screen saver is active Verify that the proper input is selected Verify that the display cable is securely attached to both the display and the video source Replace the cable with another of the same type to verify that it is not faulty Q One of the primary colors red gre
9. en or blue is missing A Replace the video cable with another of the same type Connect to a different video source to verify that there are no problems with the video card or source device Q The colors are not correct A Adjust the color temperature or the individual mix or red green and blue picture elements Q No picture using the DVI input A Verify that you are using a Dual Link DVI D cable Verify that your video card is capable of delivering a Dual Link DVI D signal A Dual Link DVI D cable will have a pinout that looks like this 18 SPECIFICATIONS een o Dot Pitch 0 2331 x 0 2331 mm Maximum Resolution 2560 x 1440 60Hz WQHD Brightness 350cd m Viewing Angle 178 left right 178 up down Video Inputs 1x Dual Link DVI D 1x DisplayPort v1 2 1x HDMI 1x VGA Audio Inputs 1x 3 5mm TRS Line In Horizontal Frequency HFR 30 158 KHz Vertical Frequency VFR 60 75Hz Pixel Clock Frequency 300 MHz PNP Standard VESA DDC2BTM Power Consumption Operation lt 50W Standby lt 1W 100 240 VAC 50 60 Hz 32 122 F 0 50 C 4 140 F 20 60 C 10 85 non condensing 25 8 x 9 6 x 21 7 658 x 245 x 552 mm Weight 16 7 Ibs 7 6 kg Certifications ETL FCC CE 19 sx Compliance Information FCC Class B Notice Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limi
10. me UP If the OSD menu is displayed pressing the UP button moves the selection highlight up lf the OSD menu is not displayed the button is ECO function hotkey DOWN If the OSD menu is displayed pressing the DOWN button moves the selection highlight down If the OSD menu is not displayed the button is DCR function hotkey SELECT If the OSD menu is displayed pressing the SELECT button enters the OSD highlighted entry If the OSD menu is not displayed the button displays the source list MENU If the OSD menu is not displayed pressing the MENU button opens the OSD menu lf the OSD menu is displayed pressing the MENU button will back out of a submenu or close the OSD menu if already at the top menu level POWER Press the POWER button to toggle the monitor ON or OFF When the monitor is powered on and a video signal is present the power indicator will glow blue When the monitor is powered on but no video signal is present the power indicator will glow yellow orange SETUP 1 Install the stand and base using the instructions in the following section or mount the monitor to a wall or desk mount using the included M4x8screws Connect video cable s from your source device s to the monitor s input s The monitor has 4 video inputs 1x DVI 1x HDMI 1x DisplayPort 1x VGA and can simultaneously display up to four video sources Use the included 3 5mm TRS audio cable to connect the audio output of your
11. ng the SELECT button opens the INPUT SELECTION menu and selects the currently highlighted video input MENU If the OSD menu is not displayed pressing the MENU button opens the OSD menu When the OSD menu is displayed pressing the MENU button will back out of a submenu or close the OSD menu if already at the top menu level 10 BRIGHTNESS MENU BRIGHTNESS BRIGHTNESS I 80 CONTRAST EEE 50 ECO d STANDARD gt DCR 4 b BRIGHTNESS Adjusts the image brightness The adjustment range is O to 100 CONTRAST Adjusts the image contrast The adjustment range is 0 to 100 ECO Preset display mode selection Four display modes Standard Text Movie Game DCR DCR stands for Dynamic Contrast Ratio which is a circuit that increases the effective picture contrast by changing the light intensity of the LED backlighting DCR tends to cause too much contrast fluctuation when dealing with swiftly moving images and is usually better suited to applications use than for use with games DCR can be turned On or Off 11 IMAGE MENU H POSITION V POSITION CLOCK PHASE ASPECT H POSITION Adjusts the horizontal position of the image The adjusting range is from 0 to 100 Only available for VGA input V POSITION Adjusts the vertical position of the image The adjusting range is from 0 to 100 Only available for VGA input CLOCK Adjusts the clock frequency The adjusting range is from 0 to 100 Only available for VGA input PHAS
12. otherwise bypass the grounding pin The power supply for this monitor accepts a wide range input voltages from 100 to 240 VAC 50 or 60 Hz with a current at least 1 75A Ensure that your power source is within these limits If not consult a professional electrician or your power company for a resolution Unplug the monitor if it will go unused for a long period of time This monitor has no user serviceable parts Do not open the case or otherwise attempt to modify this monitor Clean only using a soft dry cloth Do not use chemical cleaners solvents or detergents For stubborn deposits moisten the cloth with warm water Do not leave a single image on the display for a long period of time Doing so could cause burn in of the image It is recommended to use a variable desktop background and to use a screen saver to prevent burn in Alternatively ensure that the monitor is power off for at least 2 hours out of every 12 FEATURES 27 WQHD monitor with LED backlighting 16 9 aspect ratio 2560 x 1440 60Hz maximum resolution 1 DisplayPort input 1 HDMI input 1 Dual Link DVI D input 1 VGA input Detachable stand allows for tilt and swivel plus rotation for easy portrait landscape orientation changes Built in stereo speakers with 2 watts channel amplifier 100 x 100 VESA mounting pattern PACKAGE CONTENTS Please take an inventory of the package contents to ensure you have all the items listed below If anything is missing
13. ts are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio television technician for help Modifications Any modifications made to this device that are not approved by Monoprice Inc may void the authority granted to the user by the FCC to operate this equipment CE Compliance Statement This product is in compliance with CE directives and bears the CE mark For detailed information on specific directives please contact Customer Service or sales office or distributor WEEE Directive Compliance Statement This symbol on the product or on its packaging indicates that the product must not be disposed of with normal
Download Pdf Manuals
Related Search