User Manual
Contents
1. 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation E 1 3 1 High voltages exist within the monitor Opening of monitor case is unsafe and never necessary for operating purposes 2 In case of any failure please tum off the display at once and notify our company or the corresponding dealer The monitor is made up of many precise electronic components Any disassembly or modification may lead to damage and voiding of warranty ROSCOE VisionSystems DAY NIGHT MENU u U Q Q Front view 1 DAY NIGHT Switches from Day to Night and vice versa 2 Reduces the volume and adjust values within selected options 3 Menu Switches to setup mode See p 8 for options 4 Increases the volume and adjust values within selected options 5 Power Switch Switches Monitor from Stand by to Steady on COLOR BACKUP CAMERA SYSTEM STSK7465 INTRODUCTION Please read this manual thoroughly This manual contains instructions to make the installation of the camera and monitor easier The color backup camera system is a supplement to standard rear view mirror systems and will provide additional rear view vision when installed and maintained properly It is not intended in any way to be a substitute for careful and cautious driving All applicable traffic laws and motor vehicle safety regulations must still be obeye2. MENU button five times Press to reset device factory settings Press the MENU button to exit setup mode SPECIFICATIONS STSC141 CAMERA PICK UP DEVICE TV SYSTEM PICTURE ELEMENTS SENSING AREA IMAGE SIZE SYNCHRONIZATION HORIZONTAL RESOLUTION REQUIRED ILLUMINATION SIGNAL TO NOISE RATIO POWER SUPPLY POWER CONSUMPTION CURRENT CONSUMPTION LENS ANGLE OPERATION TEMPERATURE STORAGE TEMPERATURE WEIGHT DIMENSIONS W x H x D STSM242 MONITOR SCREEN 7 0 inch DEFLECTION ANGLE POWER CONSUMPTION POWER SOURCE TV SYSTEM VIDEO INPUT OUTPUT RESOLUTION CONTRAST BRIGHTNESS VIEWING ANGLE U x D x R L OPERATING TEMPERATURE STORAGE TEMPERATURE WEIGHT OUTER DIMENSIONS WxHxD DISCLAIMER INTERLINE TRANSFER TYPE CCD PAL NTSC 512 H x 582 V PAL 512 H x 492 V NTSC 0 2x0 1in 4 9mm x 3 7mm 1 4 inch INTERNAL 420 TV LINES 0 LUX MINIMUM F 1 2 MINIMUM 48dB AT AGC OFF 12Vde 3 5W AT 12Vdc MAX 200mA 120 D 88 H 66 V 5 F to 150 F 13 F to 158 F 0 6Kg 0 4115 3 x 2 x 2in 75 x 48 x 49mm COLOR TFT LCD 50 LEFT RIGHT 15 TOP 35 DOWN 8W 700mA MAXIMUM 12 32Vde PAL NTSC COMPOSITE VIDEO SINGLE 1VP P 75 OHM 1440 H x 234 V 350 1 400cd m2 15 x 30 x 50 15 F to 160 F 20 F to 176 F 0 5Kg 0 90lb 6 9 x 5 x lin 175 x 125 x 23mm without flush mount The use of the STSK7465 Vehicle CCTV system should not in any way be used as a substitute for carefu
3. VisionSystems Safe T Scope 7 Rearview Backup Camera System INSTALLATION USER S MANUAL STSK7465 90 21 144th Place Jamaica NY 11435 1 800 227 2095 www roscovision com WARNING To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are dangerous voltages inside the monitor There are no user serviceable parts inside 2 Avoid exposing monitor to water rain moisture etc It is NOT waterproof Any moisture inside the monitor could cause extensive damage 3 Do not disassemble the camera This voids the warranty Disassembling the camera will compromise the waterproof seal 9 STORAGE 1 Do not expose the monitor to excessive heat or cold Storage temperature 15 170 F and operating temperature is 5 150 F 2 Do not store or operate in humid environments 9 GENERAL 1 This system is intended for use in automotive applications Power source should be an automobile storage battery 12V 24V 2 Make sure all cables are connected properly Improper cable connections may damage the monitor Remove the cable connection when you do not intended to use the unit for a long period of time 3 Please install this system according to the instructions in this manual 4 Connect the system to an ignition switched power source Connection to an unswitched battery source will reduce battery life This device complies with Part 15 of the FCC Rules Operation is C subject to the following two conditions
4. a Automotive Safety Lit P N 04242012
5. d FEATURES STSC141 CAMERA 270 000 pixel image sensor 0 1 Lux sensitivity 18 IR LED Auto White Balance AWB Field of view 120 Diagonal Back Light Compensation BLC Automatic electronic iris provides a clearer more consistent image in low and bright light Compact and lightweight design installs easily into most vehicles Waterproof dustproof IP67 rating Wind deflector reduces buildup of dirt on lens STSM242 TFT LCD COLOR 7 MONITOR Menu button for Picture System and Options Single Camera Input Power stand by switch Powerful built in speaker CONTENTS OF COMPLETE SYSTEM 1 Camera with Accessories Mounting Bracket w hardware Wind Deflector 65 Camera extension cable 1 Monitor with Accessories Sunshield Duckfoot universal bracket for surface mounting of monitor on dashboard or headliner including adhesive pad Power Video Audio Distribution harness with reverse trigger IMPORTANT For typical rear view installation the rear camera MUST be connected to the distribution harness at the connector marked REVERSE Note The following instructions are for typical rear view application STSC141 CAMERA 1 Attach camera bracket close to rear marker lights centered on vehicle see Fig 1 Attachment point must be sturdy enough to support camera and bracket 2 We do not recommend mounting the camera near the lower area of the vehicle ex bumper This reduces
6. er switch will change the monitor status from standby to steady on Steady on mode status will show rear cameras view Increases the volume and adjust values within selected setting of menu options MENU Button See p 8 Reduces the volume and adjust values within selected setting of menu options DAY NIGHT Switches from DAY mode to NIGHT and vice versa HOW TO SET YOUR MONITOR TO YOUR REQUIREMENTS NOTE On screen menu commands may only be selected when monitor is in Steady on mode When monitor is in standby mode and activated by trigger signal on screen menu commands are disabled Press the MENU button once to set desired brightness Press to reduce the brightness Press to increase the brightness Press the MENU button to exit setup mode Press the MENU button twice to set desired contrast Press to reduce the contrast Press to increase the contrast Press the MENU button to exit setup mode Press the MENU button three times to set desired tint Press to reduce the tint Press to increase the tint Press the MENU button to exit setup mode Press the MENU button four times to set mirror image Press to switch on mirror image Press to switch off mirror image Press the MENU button to exit setup mode NOTE You can reset the monitor to the factory settings for brightness contrast tint and volume To do this proceed as follows Press the
7. l and cautious driving Always obey traffic laws and motor safety regulations must always be adhered to Specifications subject to change without any notice Fig 1 7 Camera mount in suggested location Mount camera assembly high Centered Camera mounting hole pattern 60 30 THRU Fig 2 Position of camera Vehicles behind truck Street Rear Bumper Typical monitor image of view from properly installed camera 11 Fig 3 Optional wind deflector Fig 4 Back of Bracket fr lrn Front of Bracket 12 Fig 6 Mounting on the dash console etc Fig 5 Camera Connector Electrical Shrink Tape Applied Properly 13 POWER INPUT RED To __ Ignition Switched Accessory Fuse 2A 250V 5x29mm Example McMastar Carr P N 6978K749 Radio Shack P N 2103766 ui GROUND WIRE BLACK To metal point of the vehicle Line noise filter CAMI la REVERSE REVERSE 7 GREEN Trigger Wire Note For typical single camera installation this trigger wire should be connected to the vehicle s back up lights circuit and the rear view camera should be attached to the connector marked REVERSE 14 VisionSystems 90 21 144th Place Jamaica NY 11435 www roscovision com Ph 1 800 227 2095 Fx 1 718 297 0323 ISO 2001120009 FM 78496 Century of QS 9000 March 1998 FM 78495 E Printed in Chin
8. nd of the power video audio distribution harness 7 For typical rear view installation connect the camera extension cable from the rear view camera to the harness s connector marked REVERSE 8 The green wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse 9 FUEL TANKERS amp OTHER SPECIALTY VEHICLES All electrical equipment fitted to petroleum vehicles must be connected via battery master switch and must be isolated from the battery while the vehicle are loading and unloading For other specialty vehicles please check applicable code and regulations prior to installation 10 Always consult your dealer when fitting any electrical or electronic equipment to a vehicle fitted with a CAN bus or multiplex system IMPORTANT For installations not requiring typical rear view images please refer to the wiring diagram Fig 5 and the particular vehicle s electrical schematic for selection of proper power and trigger connection points FUNCTIONS AND OPERATION MONITOR 1 POWER When the ignition is switched on the monitor will be in standby mode no image will be on the screen waiting for trigger signal When a trigger wire is energized by 12v power such as backup lights turning on the image captured by the selected camera will appear on the monitor Pressing the pow
9. on harness at the connector marked REVERSE 2 Do not run the cable over sharp edges or corners Do not kink the extension cable Keep the cable away from hot and rotating parts 3 Stretch and tightly wrap tape around section where connectors meet Cut excess tape if any Place hand over taped area and squeeze tightly This will ensure a tight fit Over time tape will tighten more See Fig 5 4 Fasten all cable runs and secure all excess cable 5 WIRING CAMERA AND MONITOR 1 Connect the red wire to an ignition switched accessory ex radio power source and connect the black wire to chassis ground See wiring diagram for connections See Fig 5 2 Before drilling be sure no cable or wire is on the other side Be sure to drill a 20mm 0 8in diameter hole only 3 Feed as much cable as possible into vehicle and clamp securely This reduces the possibility of it being hooked or snagged 4 Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components 5 Camera Drill a 20mm 0 8in diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply sealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle 6 Monitor The monitor terminates in a 13 pin male connector which should be connected to the mating 13 pin receptacle e
10. the view of the camera and increases the chance of physical damage to the camera Before installing bracket to designated area place gasket on the back of the bracket Place screw grommet on both top and bottom positions then tighten screw to hold in place Fig 4 p 13 shows how the bracket gasket grommet amp screws should be installed Apply to vehicle and tighten to secure bracket into place Attach camera to bracket using screws provided Adjust angle as indicated in Fig 2 Use rear bumper and back of vehicle as a reference point 8 Wind deflector may be installed This deflector is designed to reduce the buildup of dust dirt and moisture on the camera lens See Fig 3 STSM242 MONITOR 1 Attach monitor inside vehicle in a location convenient to the driver ex center of dash overhead or flush mounted in dash 2 Attach the duckfoot bracket to the dashboard or to the headliner using self tapping screws and or adhesive pad N aooe 3 Fasten monitor to duckfoot and adjust mounting angle to allow optimum driver viewing comfort See Fig 6 STSH341 CAMERA EXTENSION CABLE 1 The camera to cable connection is waterproof Be sure to position the cable properly The male end attaches to the camera The female end attaches to the power video audio distribution harness typically located under the dashboard See Fig 7 IMPORTANT For typical rear view installation the rear camera MUST be connected to the distributi
Download Pdf Manuals
Related Search