Single channel MPEG-2 /H.264 Encoder/Transcoder User`s Manual
Contents
1. as is unless mentioned otherwise The manufacturer does not bear responsibility for any consequences of using the software The software can be used without any limitations Additional information on the software interfaces can be sent upon request The manufacturer reserves a right to bring any changes to the product software or description without notice Please ask manufacturer for latest information and updates Dear customers We make improvements and or changes in our products and we reserve the right to make changes without notice Though every effort has been made to ensure that this document is current and accurate more information may have become available subsequent to the production of this guide Our products are under continual improvement so we would like to draw your attention to the fact that the old model devices may not be supported by the most recent version of our software It is caused by using in our equipment advanced technical solutions and new electronic components We are pleased to receive at info dv lab com comments and remarks regarding our products and software At the same address we are ready to provide further information about the products application and updated software 21 29 5 Appendix 5 1 Environment Requirement Operating Temperature 5 40 0 45 C short time air conditioning is recommended Device power air conditioning power and lighting power are independent of each other Device po2. SD format Digital to digital decode and re encode with minimum loss in video quality Supports multi bitrate transcoding Up to 1080 HD output Audio is passed trough PID filtering Built in multiplexer allows to generate output TS with transcoded programs and or original programs which are applied to the input PSI generation Supports OTA EPG DVCrypt CAS 3000 10000 100000 subscribers Input interface DVB ASI 1 Output interface DVB ASI 2 and IP 1 4 29 1 4 Specification Single channel MPEG 2 H 264 Encoder Transcoder User s Manual Video Input Analog Input Composite BNC 750 Level 1 Vp p Digital Input SDI BNC 750 or HDMI HDMI 19pin Level 800mVp p SDI Aspect Ratio 4 3 16 9 Audio Input Analog Input 1 Stereo 2 channels XLR Freq Range 20Hz 20KHz Impedance 600 0 20KQ Digital Input Embedded SDI or HDMI Sampling Rate 48 KHz Video Encoder Encoding MPEG 2 HP HL MP HL MP ML MPEG 4 H 264 HP L4 MP L3 Encoding Rate 0 5 15 Mbps Chroma Format 4 2 0 Bit Rate Mode CBR VBR Audio Encoder Encoding MPEG 1 Layer 64 320 Kbps Sampling Rate 48KHz TS Output Transport Stream 2 ASI Connector BNC 75Q TS Bit Rate 0 5 14 Mbps Packet Format 188 Byte IP TS Output and Ethernet control Ethernet type 10 100 Base T RJ 45 Format UDP IP RTP IP IP Addre
3. The utility doesn t require installation Before changing the IP address connect the Device to Ethernet hub switch connect to it also a PC having installed network board network board IP address should be in the Device IP address range For example the Device IP address is 192 168 0 254 then network board IP address can be in 192 168 0 1 192 168 0 254 range network mask 255 255 255 0 Then run EthernetSetup exe the program will find the Device x English 7 20 BF DE 00 00 1E 192 768 0222 gt 0 BF 0B 00 08 FE 192168 0 191 Refresh Blink Ping Setup Passport Close Select the device and press Setup button Ethernet Setup x English lt gt 20 BF DB 00 00 1E 192168 0 222 70 BF DELOD ONLEN 413411 Network parameters d TE IF address Network mask 255 255 255 Default gateway The Network parameters window will appear where you can change the Device IP address and network mask The procedure of assigning IP address should be performed for all Devices before adding them to the system Pressing Ping button you can check connection between the PC and the Device If you press Blink button the selected Device will flash red LED built in Ethernet connector three times Attention It is not recommended to change the Device IP address after the Device has been already added to the system as it will cause connection failure To re establish connection it
4. automatic search doesn t work in this case it is necessary to do the following Connect the new Device to the local network or to the Server directly and set the IP address as described below Connect the new Converter to remote network Run adding procedure and select the option The module is not listed here Enter IP address of the module directly Add new module x Select a new module from the list and click Nest Selected module will flash red LED three times if you click lt Blink gt Click lt Refresh gt to refresh the list AE E Refresh Blink l The module is not listed here Enter IP address of the module directly lt Hasan Dame gt Ormena Enter IP address of the Device Module Add new module 4 x Enter IP address of the module and click lt Next gt to proceed IP address 192 168 1 100 The server will try to communicate with the Device and add it to the system Add new module x ding new module to the system ff this operation takes too much time han the system cant communicate with new module ou can click lt Cancel gt to stop operation E Attention All Devices are delivered set to the IP address 192 168 0 254 or 192 168 0 253 network mask 255 255 255 0 The Devices should have different IP addresses when you add them to the system The delivery set includes EthernetSetup exe utility which makes it possible to change Device IP address and network mask
5. if you select No then the wrong selections are highlighted with red color and when you hover the mouse on them a hint will appear Fig 3 8 E 2 channels encoder settings H 262 H 264 AVO SDL CVBS input ext channels Ioj lt tf for all channels ___Restory factory settings PRIANO Je soa 7 only for selected channel Frame rate Out bitrate of general remultiplexer f tf 50i Ga adi 12400 kBit s On Channel 1 On Channel 2 Input signal definitio Input signal typ tf SD rf HD f SD tf OBS Test signal SODI signa Set audio typ Digital audi Anal Set stereo pai Set stereo grou a Ee e lo oe Cla a Digital MO A AA A A A joo D E 6 der presst output sic Code Recommended Mpeg E Mpeg AVC Enabled extended TS Bit ratek Bikes h 264 262 Picture size Preset Transport stream 400d z Wideo strea Profile 720x576 C WBR man lam 720 Mas Average Min Level A Height 576 4000 2000 f DODO Lewel 3 0 Level 3 0 gt Aspect ratio sd 43 Audio stream Jn 128 Audio off Piogiam Elementary streams ID GO Number 21 04 PER 256 video 1096 Struck Ber Frame interval 12 ID 1 024 Audio 4097 Jw Closed Fig 3 8 The button Recommended restores the operating parameters that can be saved by pressing the Write settings Fig 3 8 The button Restore factory settings is used to return the encoder to the working condition in th
6. r Click Begin search to start the scanning process When the scan is complete the message appears Fig 3 13 Channels on input streams Tables search completed Close the window and select menu item lt Remultiplexing gt to continue settings 15 29 When the scan is complete Single channel MPEG 2 H 264 Encoder Transcoder User s Manual e Select input programs that you wish to add to the output stream and drag them with mouse to the right window Fig 3 14 e Selecta program for transcoding in the right window e Switch on Transcoding Select channels for output stream Channels in input stream E 0 FERREE Input 1 video CCTW9 0x0804 video ATA 0x080B video Vesti 0x080C video Aljazeera Intl 0x080D video TELESUD 0x080E MM O video Demain 0x0809 Channels in output strea Kanam sexonsoro noroxa su5pam o 3 The total bitrate of channels in stream 0 000 Mbps normal Channels with Conditional Access ouquert _ Access is open E E video M6 Boutique la chai 0x0808 El video Demain 0x0809 M E video CCTV9 0x080A Added 3 Bouquet Added 0 Added 0 Bouquet Added 0 Added 0 Bouquet Added 0 souquet _Becess is open 5 Added 0 _____ Bouquet_ Added 0 Fr Open channels Access is open Access is open Access is open Access is open E Above bouquet Added 0 E Change the channe
7. selected from program menu The Encoder is intended for real time encoding of SD HD signal into MPEG 2 SD or H 264 SD HD format The Transcoder is intended for real time transcoding of an SD HD program from MPEG 2 to H 264 format or vice versa and for transrating from MPEG 2 to MPEG 2 The Encoder Transcoder can output two independent Transport Streams TS which are broadcast simultaneously One of the two TS provides high resolution 1920x1080 or less for high quality broadcasting the other TS provides low resolution 320x240 or less for broadcasting to mobile devices or Internet The Encoder Transcoder enables multiplexing of the two TS onto any of the two ASI outputs or any of the two IP addresses 1 2 The Encoder key features e Composite HDMI HD SD SDI video inputs e Full HD 10801 support e Analog XLR and Serial Digital embedded audio inputs e Provides internally generated PSI e Selectable MPEG 2 SD or H 264 SD HD real time video encoding e Simultaneous output of 2xTS ASI with UDP IP or RTP IP transport stream e CBR or VBR outputs e User selectable resolution and bit rate e MPEG 1 Layer II audio encoding e Control and monitoring via LAN Ethernet 3 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 1 3 The Transcoder key features Transcoding of an SD HD program from MPEG 2 SD HD to MPEG 2 SD format from MPEG 2 SD HD to H 264 SD HD format from H 264 SD HD to MPEG 2
8. 0 59 94i 1440x1080 50i 1440x1080 60 59 94i 960x1080 50i 960x1080 60 59 94i 720x1080 50i 720x1080 60 59 94i SD Mode 720x576 50i 720x480 60 59 94i 104x576 50i 704x480 60 59 94i 18 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 3 5 2 IP Outputs Settings Click icon IP on the toolbar Fig 3 11 IP output configuration wndow appears Fig 3 17 x Status E 1 192168 32 33 1 234 Configure 2 192168 32 53 1 236 xl tae a Stop Source Multipl x d pe COLE hMiultiplez ed Destination Channel 1 Es Channel 1 PES Tera Stop all IF inputs Fort Eontiqure Start Stop Start all Stop all Fig 3 17 The encoder has the opportunity to work with two IP addresses sent in one IP stream Each encoder channel may have its own IP address There are several operation modes for each IP channel 1 Output is disabled 2 The output is commutated to channel 1 3 The output is commutated to channel 2 4 The output delivers two multiplexed channels The second channel works in the same mode If two channels work in the Multiplex mode stuffing should be switched off disabled or one channel should be disconnected while the second may work in the multiplex mode both with the enabled and disabled stuffing In the channel1 and channel modes stuffings are disabled It is necessary to choose IP address and port that the stream will be broadcast to as well as the pr
9. Outputs Settings 8 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 3 Operation 3 1 DVBSetting program Setting of the Encoder Transcoder parameters is done using DVB_ Setting utility which is a part of the DVB Toolkit program It allows you to adjust the speed of the output TS bit rate and change the mode of operation of the encoder with a constant bit rate CBR or a variable VBR The output resolution and input signal format are also controlled 3 2 DVBToolkit installation 3 2 1 Server PC requirements Please check that following requirements are met e CPU 1 GHz or faster e RAM 1 GB or more e HDD at least 1 GB of free space e LAN and USB interfaces e Operating System Windows XP Windows Vista Windows 7 Windows 8 3 2 2 Software installation Run the included DVBToolkit_Install exe installation file and follow the prompts 3 2 3 Starting the Management Program The Client Program can be launched from the Start menu All Programs DVBToolkit Client When you launch the Client the program will ask you to choose the connection type xl 0 This computer Remote server 213 152 151 153 Server port 2100 Cancel Fig 3 1 Select This computer if the program Server is installed on the same computer or Remote server if it has been installed on another PC Then it is necessary to enter the IP address and port of the PC on which you have installed the server After the
10. Single channel MPEG 2 H 264 Encoder Transcoder User s Manual ang DIGITAL VIDEO LAB Single channel MPEG 2 H 264 Encoder Transcoder User s Manual Version 1 0 Date May 2013 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual CONTENS DIRECTORY 1 PRODUCT OUTLINE 1 1 OUTLINE 1 2 THE ENCODER KEY FEATURES 1 3 THE TRANSCODER KEY FEATURES 1 4 SPECIFICATION 1 5 FRONT PANEL ILLUSTRATION 1 6 REAR PANEL ILLUSTRATION 2 HOW TO WORK WITH MPEG 2 H 264 ENCODER TRANSCODER 2 1 ENCODER TRANSCODER MAIN PART 2 2 SETTING OF THE ENCODER PARAMETERS 2 3 SETTING OF THE TRANCODER PARAMETERS 3 OPERATION 3 1 DVBSETTING PROGRAM 3 2 DVBTOOLKIT INSTALLATION 3 2 1 SERVER PC REQUIREMENTS 3 2 2 SOFTWARE INSTALLATION 3 2 3 STARTING THE MANAGEMENT PROGRAM 3 2 4 ADDING DEVICE TO THE CONFIGURATION PROGRAM 3 3 ENCODER SETTINGS 3 4 TRANSCODER SETTINGS 3 5 OUTPUTS 3 5 1 RECOMMENDATIONS 3 5 2 IP OUTPUTS SETTINGS 3 5 3 ASI OUTPUTS SETTINGS 4 WARRANTY 5 APPENDIX 5 1 ENVIRONMENT REQUIREMENT 5 2 GROUNDING REQUIREMENT 5 3 HOW TO CONNECT NEW DEVICE TO THE SYSTEM THROUGH ETHERNET TCP IP 23 5 4 HOW TO ADD A NEW DEVICE TO THE SYSTEM 25 O OO O O O O O CO 0 0 N DJ Ul a Y O W N N PRO N N A gt 22 gt dd N N N 2 O OO O AN O Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 1 Product Outline 1 1 Outline The device can work in two modes Encoder or Transcoder The necessary mode is
11. Video 4096 ID fi 024 Audio 4097 Closed Fig 3 6 3 3 Encoder Settings The encoder has an output re multiplexer which allows to set the desired output bit rate of the encoder Mode Test signal allows you to turn on the pitch sound and the color bar generator If any of these parameters have been chosen incorrectly the following warning appears when you click Set selected settings Fig 3 7 t Encoder settings H 262 H 264 AVC with extende olsi Bestom factory settings Ce Set selected settings Input signal definitio Input signal type fe SD HD f SE ABR WES Test signal Gut bitrate of general remultipleser reco kE it Digital audi Anal Set stereo pai Set grou Sas i e gt les A ES ca Digital AAA AA AAN fo E 6 Encoder settings E S e M Mot recommendable parameters of encoding x Detected the out values of parameters encoding excellent from recommendable that can cause the improper forming of build output stream To write down the entered parameters Height 576 Level I ars Average Hin 4000 2000 fi 000 Level 40 Aspect ratio ad 4 3 Audio stream 73 128 Audio off Program BEGERE SSD Go Number 2048 PER 256 struct IBEP Frame mterval 12 videa 4096 19 1024 Audio 4097 Closed 12 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual If you select Yes then set parameters will be applied and saved
12. connection to the Server system of administration Login window will appear 9 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual x Account Ag FMAHACTRSTOp al operator Oneparop al engineer IM HikEHEp Info VHpoprayHa Pt EPG Aneparop Tenera Fig 3 2 The program uses a system of administration which is structured as follows e DVBToolkit contains several functional modules e Administrator is a main user of the DVBToolkit program e Administrator enters the program as an Administrator with personal password and appoints the other users e The Administrator also can on off some functions of the DVBToolkit program e The number of users and their rights determined by the administrator All default passwords are empty Clicking the Login button brings you to the main window A A AAA un Da DVBToolkit Client Modules 0 Main View gt il Gl Al a Label PIDs DEC Fig 3 3 3 2 4 Adding a device to the configuration program 1 Select View Modules from the menu or icon sn 2 Click on Add new module icon dh Click Add new module icon and the following window will appear Fig 3 4 10 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual Please select connection type for new module R5485 te Ethemet Choose address for new module leave blank to automatically choose first available address IT Replace existing module at add
13. e event of incorrect settings You can change the PID and the ID number of the elementary stream 13 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 3 4 Transcoder Settings 1 Select Transcoder mode Fig 3 9 Edit module parameters 4 x Channels Module E Module 01 1 Transcoder combo CAS 100000 i n 1 0800 ME Boutique la chal 21001 CCTW9 i 31002 Tc M Demain z 4 1004 Tc Ex Demain Extra Network information settings EPG settings OT settings Extra options Transcoder cancel Fig 3 9 2 Click OK and wait while the device switches from the Encoder to Transcoder mode You can see the progress in the status bar of the DVBToolkit Fig 3 10 Wait until the color of the device in the system becomes green No 01 System bitrate 53332 Kbit s OK 2 xTranscoder combo CAS 100000 192 16485 32 60 IP BbIXOA BKAKOYEH 0 6F 06 00 14 BE Fig 3 10 3 Scan input ASI streams and take programs for transcoding click icon 5 In the main window toolbar Fig 3 11 Da DVBToolkit Client Modules 2 Main View la SR oo ahhrvr75 Module 5 Label PIDs DEC Fig 3 11 14 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual The Multiplexer Window appears Fig 3 12 E Input streams ASI remultiplexor v3 00 07 2 Search service Information on input streams Remultiplexing Tramscoder
14. e of bitrate for output stream E Fig 3 15 16 29 In this window you can e select the output format MPEG2 or MPEG4 e switch on an additional stream e switch off the program from output stream Single channel MPEG 2 H 264 Encoder Transcoder User s Manual Having made the required changes click OK and the previous window will return Fig 3 14 Next Step Measure the bit rate of the selected stream and compare it with a valid value If it is valid click Write settings in the device and move on to the next window Ta Input streams ASI remultiplexor v3 00 07 2 4 E Settings Search service information on input streams Remultiplexing Previous remultiplexing Appreciate of bitrate in working stream Output stream ASI Qutput stream 0x0070 Channels in strea ME Boutique la chai C CCTV C Tc M Demain C TelEx Demain Channel number 0x0800 m udiofmaintenance No extra lang for audio maintenance PID PCR 0x1000 h Video 0x1000 h Audio 0x1001 h Du PCR 0x0600 h Video 0x0600 h Audio 0x0601 h Dynamics of bitrate tracking in output stream 0 Limit of speed 53 33 Mbit e Not defmed Maximum bitrate was fixed mE ac Delete channel in output stream if bitrate out of Return to remultiplexing Write service information in output System adress 1 Type of device Transcoder Ou
15. is necessary to repeat procedure of adding the Device to the system again
16. l s position d in the list 1 Oyucrurb obnactb BBOMA JV ranscoding switch on How it s make The recommended speed of the output data stream Mbps Preliminary bitrate control of output stream Mbps Fig 3 14 Write settings in the device System adress 1 Type of device Transcoder Rough estimate of bitrate for output stream 0 000 Mbps E If necessary you can Click Change the Transcoding parameters and Settings window will appear Fig 3 15 2 Input streams ASI remultiplexor v3 00 07 2 Dl xl Settings Search service information on input streams Remultiplexina Previous remultiplexing Appreciate of bitrate in working stream TpaHckoaumpopaHne KaHana e Demain E Channel parametrs bitrate 2 397 Mbps provider DVLab type number 0x0809 pid 0x0401 PCR pid 0x1010 VIDEO pid 041010 bitrate video stream 1 880 Mbps type stream 0x02 Audio tracks track 0x1011 type stream Ox04 Broadcasting language no V MCKAOYHTb B BbIKOAHOM NOTOKE MporpaMMy ANA TPAHCKOAHPOBAHHA Hactpolku kogepa st BxogHol BbikoaHo O MPEG2 OMPEG4AVE C MPEG 2 MPEG A AVC Main TS Extended TS Konek Bit rate kBit s Transport stream Video strea C VBR CBR Max Average Min wan C H He KI Struct AUTO Frame interval AUTO Deblocking filter mode OFF A Closed System adress 1 Type of device Transcoder Rough estimat
17. n in notification area when connected I Notify me when this connection has limited or no connectivity E Cancel The computer IP address must be assigned statically As example IP address is 192 168 1 3 shown at the Figure below Internet Protocol TCP 1P Properties E 2 x General ou can get IF settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an P address automatically f Use the following IP address IP address 192 768 1 3 Subnet mask 200 255 255 Default gateway Obtain DNS server address automatically f Use the following DNS server addresses Prefered ONS server Alternate ONS server Connection scheme is shown below KoHeepTep ss KoHBepTep The server is connected to a standard Ethernet hub switch The Device is connected to the Ethernet hub switch There can be other computers in this local network If the server is connected to a local network containing other PC it is recommended to install the second network adapter in the server in order to guarantee fail safe and secure connection In this case the connection scheme should be the following d O t KouBepTep i Hub Kouseptep KoHBepTep First network adapter and Device are attached to a hub The second network adapter is attached to other hub c
18. onnected to other PC Select Module interface Ethernet option in Server settings x About Server settings vag D WCrppt Server port 8100 Server ver 2 4 Apr 14 2010 E r Module interface c 2003 2010 DYL 7 RS 485 COM3 Licensed to DWLab 0001 0800 IT Bind to network adapter Subscribers 100000 DVB settings SMS notifications Enable Setup Cyrillic encoding ETSI EN 300 468 Debug Integration J Enable debug logging I Biling software integration mode Keep debug information days 7 v Interface language Send problem report Language English Edit New Cancel If the server contains special network adapter for connection to Device it is necessary to select Bind to network adapter option and assign its IP address 132 168 5 4 How to add a new Device to the system To add a new Device to the system connect it to the hub by a cable and switch it on Press button Add new module Select connection type Ethernet Add new module New Device connected to the system will be searched their MAC and IP addresses will be listed Search can be repeated by pressing Refresh button If there are a few Devices it is difficult to determine the Device among others In this case you can select the Device in the list and press Blink button The selected Device will flash red LED built in Ethernet connect
19. or three times Next step is entering IP address of selected Device xl Select a new module from the list and click lt Next gt Selected module will flash red LED three times if you click lt Blink Click Refresh to refresh the list TT The module is not listed here Enter IP address of the module directly lt Hasan Omena The server will set the IP address xl Change network settings of the module and click lt Next gt to proceed You can leave current settings unchanged IP address delos Dc AN Network mask 255 255 25 0 Default gateway Select any free IP address in the range of this local network for example we use addresses from 92 168 1 100 to 192 168 1 200 and enter it Network mask and Default gateway should be set only if the Device will work in other sub networks for the new Device and add it to the system The IP address and MAC will be shown in Devices window in Control Software It will be impossible to change the Device IP address hereafter To change the Device IP address it is necessary to delete the Device from the system and add it again Add new module x New module was successfully addedtothe system ick lt Finish gt to continue Hace Ore When the Device is added it should be set Double click on the Device number and it will appear Converter setting window Notes If the distance between the Server and Devices is rather long and there are routers and
20. otocol RTP UDP RTP for each of the channels When the required parameters are selected click start and close the window It is possible to check monitor work of IP inputs using VLC player 19 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual Mepgra nponrpbiBatenb VLC Mensa BompombegeHHe Ayaro Bageo MHETpyMEHTEI Bug Momo Select Media Network and enter the necessary parameters An example is given on Figure below OrkpbiTb Megna alin CI walin o Auck mu F E Cetb g YcTPOMCTBO 3axBaTa Cereso npoTokon Mporokron Aapec UDP b 192 168 0 32 1234 Di NokasaTb DONONHATENbHbIE NapaMeTpel 3 5 3 ASI Outputs Settings El al All channels Edit module parameters l J x Channels Module Module ds 2 H 264 HD 45 combo 1 0838 P8 1 2 0834 F8 2 Extra Network information settings ASIT output Multiplexed d 4512 output Multiplexed Channel 1 Mode Channel 2 Multiplexed System bitrate 12400 Khit s 1 0838 Fig 3 18 20 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 4 Warranty Warranty period 24 months from the selling date The manufacturer does not take any responsibility for defects occurred at the customer s fault or trading company s during careless transportation improper storage technical service or usage mechanical damages violating the operation rules The software is delivered
21. ress Existing module should be compatible with new one and disconnected Fig 3 4 Click Next and follow the wizard s prompts You can assign new IP to the device at next step See Chapter 5 4 Finally new Encoder will be added to the main window Fig 3 5 amp DVCrypt Client Modules Main View 2 Be eE EARAoOS DERIO AO Module sms OOOO El Ready pdrin ETT Fig 3 5 When the Encoder has been added click 2 to change the settings Fig 3 6 11 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual li Encoder settings H 262 H 264 AVC with extended channel Restor factory settings Set selected settings Input signal definitio Input signal typ f SD HD fm SDI HDMI 7 CWBS Test signal Cut bitrate of general remultiplexer 7600 kBit s Digital audi Anal Set stereo pai Set group peal i eal lea 2 we a Digital Dinar aa AAA 1 111 ss ao ooo ooo ao 1d foo MAA sE E Encoder settings Code Recommended Mpeg f Mpeg AVC J Enabled extended channel Extended channel Secondary TS Bit rate k Bikes h 64 262 Picture siz Transport stream E000 Profile Preset 7204576 i ll MAIN Width 20 EJ E Level Height 576 E Fiir 4000 2000 fi ada Level 4 0 Aspect ratio ad 43 Audio stream a 128 Audio off Program Elementary streams ID Number 2048 PCR 256 GO Struct leer Frame interwal 12
22. ss Format Multicast Unicast TS Bit rate 0 5 60 Mbps TS Packet format 188 Byte General Power 220V 20 Power Consumption Max 8W Size 19 1U 480 45 180 mm Weight 3 Kg 5 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 1 5 Front panel illustration e O D L R SD Eee a eee CC ms ma EOTYPE 6 6 6 VELO O 0 MODE ll H262MPEG4HD SD ENCODER oe 5 bt ih i e 345 67 8 9 10 N y gt 5 SD lai S J e E VIDEO TYPE o o 6 LEVEL O 90 MODE e O VIDEO AUDIO 345 67 8 9 10 Power on off switch 2 Power Status Indicator 3 Input Signal Type Indicator SDI A a 4 Input Signal Type Indicator HDMI emm e 9 Input Signal Type Indicator CVBS TA aoe Video Source Status Indicator Green LED signal is available Red LED no signal Audio Source Indicator Left Audio Source Indicator Right 7 Yellow LED Low level Input Signal standard SD or HD Green LED yes 6 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 1 6 Rear panel illustration O ETHERNET ASI OUT 2 ETHERNET AU DIO IN LEFT O O RIGHT O HDMI CVBS O 1 o SDI ASI VIDEO INPUTS HDMI input CVBS input HD SD SDI or ASI input Two ASI outputs 6 ETHERNET IP Analog audio input Left KA Analog audio input Right 2 Cooling FAN 7129 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 2 Ho
23. tput stream parameters Fig 3 16 Click the Write service information in output stream Wait until the completion of the process Transcoding with 2 output streams is possible only when output is set as H 264 17 29 Single channel MPEG 2 H 264 Encoder Transcoder User s Manual 3 5 Outputs The Encoder Transcoder has 2 IP outputs IP output may be used for monitoring or IP broadcast It is possible to output the multiplex In this case the main IP output carries the multiplexed TS Each IP output of the encoder may have its own IP address 1 Channel 1 2 Channel 1 The channel with is the channel with the lower resolution Supported protocols UDP RTP The Encoder has two equal ASI outputs each of which may operate in one of the following modes 1 Channel 1 2 Channel 1 3 5 1 Recommendations The maximum bit rate can not exceed 15 Mbit s CBR Mode The difference in speed between the transport stream and the video stream is recommended to choose TS TV Ta at least 400 kbit s Where TS transport stream TV video stream TA audio stream VBR Mode The minimum bitrate min 0 0 75 the average bit rate average Maximum bit rate max 1 2 2 medium average bit rates Bit rate transport stream is not less than 400 kbit s bit rate greater than the maximum bitrate audio It should be borne in mind the recommended resolution mode for encoder HD Mode 1920x1080 50i 1920x1080 6
24. w to Work with MPEG 2 H 264 Encoder Transcoder 2 1 Main part e Prepare relevant environment for installation See 5 1 e Ground the device See 5 2 e Connect Power Cord 14 Fig 1 2 e Connect ASI OUT to the device with ASI Input 5 or 6 Fig 1 2 e Connect Ethernet port to PC for setting of the Encoder Transcoder modes and parameters RJ45 7 Fig 1 2 e Switch on Power 1 Fig 1 1 Set Encoder Transcoder IP Address using EthernetSetup utilite See 5 3 e Launch PC DVB Toolkit program e Add the Encoder Transcoder to the System The wizard will help you connect it to the system See 5 4 e Start DVB_ Setting program from the DVBToolkit s client See 2 1 2 2 Setting of the Encoder parameters e Start DVB Setting program from the DVB Toolkits client3 2 See DVBToolkit installation e Set the Encoder parameters you need See 3 3 Encoder settings Save the new parameters to the Encoder Click Set Selected Settings button After saving the Encoder is ready for use 2 3 Setting of the Trancoder parameters e Select Transcoder Mode 2 3 Trancoder Settings e Setthe Transcoder parameters you need See 3 4 Transcoder Settings e Save the new parameters to the Transcoder Click Parameters Settings button After saving the Transcoder is ready for use 2 4 Setting of the Output signal parameters e Setthe IP Output See 3 5 2 IP Outputs Settings e Setthe ASI Outputs See 3 5 3 ASI
25. wer requires AC power 220V 50Hz Please carefully check before use Machine Hall Floor Electric Isolation Dust Free Ground anti static material 5 2 Grounding Requirement Good grounding is the basis of reliability and stability of devices Good grounding is the most important guarantee against electric discharge and interference Coaxial cable s outer conductor and isolation layer must ensure proper electric conductivity with the metal housing of device Grounding conductor must adopt copper conductor in order to reduce high frequency impedance and the grounding wire must be as thick and short as possible It is prohibited to use any other device as part of grounding of electric circuit The area of the conduction between grounding wire and device s frame should be no less than 25mm 5 3 How to connect new Device to the System through Ethernet TCP IP Server computer setting The server computer must be equipped with network adapter with installed TCP IP Network adapter properties Local Area Connection Properties E E 21 xj General Authentication Advanced Connect using BS Intel 21140 Based PCI Fast Ethernet Configure This connection uses the following items 4 Install Uninstall Properties Description Transmission Control Protocol nternet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks W Show ico
Download Pdf Manuals
Related Search