Home

BridgeX GT Series BX5020 Gateway IB to Ethernet

1. The fan unit is not receiving any power Check that the fan unit is properly and completely inserted All fans must be operating while the power supply is plugged in Ifthe gateway shuts down due to over temperature unplug the gateway wait 5 minutes and replug in the gateway 2 2 6 3 Power Supply Status Indicators The gateway is available with one or two factory installed Power Supply Units For gateways with only one unit installed a second Power Supply Unit can be added to increase security hot swap ability and to add redundancy See Section E Replacement Parts Ordering Numbers on page 25 for ordering part numbers Figure 9 BX Gateways Power Side Panel PSU LED Fan LED PSU LED gt a a at Secondary Power Fan unit PSU 1 Supply Unit Primary Power Supply Unit The primary power supply unit PSU1 is located on the right side of the power side panel with PSU2 on the left side Each PSU also has a single 2 color LED to the right of the PSU that indi cates the internal status of the unit 18 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 PSU status indicators are also located on the left side of the connector IB ETH side panel and labeled PSU1 and PSU2 Table 8 Shows the explanation of the PSU Status LED colors Table 9 PSU Status LED Configurations LED Confi
2. 14 Ableitstrom gt 3 5mA LEAKAGE gt 3 5mA WARNUNG Hohe Ableitstrom Earth Verbindung bevor Sie die Verbindung von wesentlicher Bedeutung werden 15 Add GND Verbindung Informationen Add GND connection information Bevor Sie dieses Ger t an das Stromnetz die Schutzerde Terminal Schrauben dieses Ger t muss an den Schutzleiter in der Geb udeinstallation 16 INSTALLATION CODES INSTALLATION CODES Dieses Ger t muss installiert sein entsprechend auf die neueste Version des Landes National Electrical Code F r Nordamerika m ssen in bereinstimmung mit den gel LA tenden Vorschriften in der US amerikanischen National Electrical Code und dem Canadian Electrical Code 17 Zusammenschaltung von EINHEITEN INTERCONNECTION OF UNITS Kabel f r den Anschluss an das Ger t RS232 und Ethernet Schnittstellen m ssen UL zertifiziert Typ DP 1 oder DP 2 Hinweis wenn nicht mit Wohnsitz in LPS Schal 4 tung Uberstromschutz Eine leicht zug ngliche Auflistung Abzweigleitung Uberstrom Schutzeinrichtung 20 A bewertet werden m ssen in dem Geb ude Verkabelung 56 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Appendix G Advertencias de seguridad para la insta lacion Spanish 1 Instrucciones de instalaci n Antes de conectar el equipo a la fuente de alimentaci n leer todas las instruc ciones de instalaci n 2 Instalaci n en un lugar con acceso restringido Esta unidad
3. Cabling SFP Passive cables 76 15W or 259 83BTUs hr SFP Active cables 95 76W or 326 75BTUs hr QSFP optical cables 99 68W or 340 12BTUs hr Optical Cable Temperature 0 to 45 Celsius Port Types SFP SR Humidity 10 90 non condensing SFP LR Acoustics 7 2 Bel 71 6 dB A SFP LC LC SFP 1000BASE T Dissipated Power through SFP 1 5W QSFP 2 0W Protocol Support Regulatory Compliance InfiniBand Auto Negotiation of 40Gb s 20Gb s Safety UL60950 10Gb s C UL to CAN CSA 22 2 QoS 8 InfiniBand Virtual Lanes for all ports No 60950 1 TUV GS to EN 60950 1 Management Baseboard Performance and Device Amendment Al A4 All management Agents for full InfiniBand CB IEC60950 1 all country In Band Management deviations EMC Emissions CC 47CFR Part 15 Class A ETHERNET PORTS Ethernet over InfiniBand EolB proto EN 55022 Class A ICES 003 Class A VCCI Class A AS NZS CISPR 22 Class A CISPR 22 Class A EN 55024 EN 300386 CE EU IEC 60068 2 64 Random Vibration EU IEC 60068 2 29 Shocks Type I II EU IEC 60068 2 32 Fall Test Mellanox Technologies 41 Rev 1 8 Table 13 BX5020 1S Specification Data es Reliability Availability and Serviceability Features Switching Perfor Hot Swappable Fan Module and Power Sup mance Simultaneous wire speed any port to any 1 1 Redundant plies port Addressing 48K Unicast Addresses Max per Subnet Bridging Capacity 16K Multicast Addresses
4. 2 GB ECC enabled 400 MHz CL3 FLASH 16 MB NAND 1024 MiB PCI Bus Dev Venld Devid Class Int PCIEO link is not up PCIE1 successfully set as root complex 01 00 15b3 bd34 0c06 00 Net ppc_4xx_eth0 ppc_4xx_ethl Hit Ctrl B to stop autoboot O Mellanox FabriclT Mellanox Technologies 39 Rev 1 8 Troubleshooting Boot Menu 1 EFM_PPC_M460EX EFM_1 1 1000 2010 06 24 16 32 03 ppc 2 EFM_PPC_M460EX EFM_1 1 1200 2010 06 25 18 00 03 ppc 3 U Boot prompt Choice 5 Select the image to boot 40 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Appendix A Specifications Table 13 BX5020 1S Specification Data Physical Power and Environmental Size Weight Mounting SerDes Speeds Connectors and 1 74 1U Hx 19 W x 21 26 D 44mm X 436mm X 629 mm 9 828kg 21 671bs 19 Rack mount 10 20 40 Gb s per port Input Voltage Typ Power Passive cables Active cables optical cables Max Power 100 240VAC 50 60Hz 62 44W or 213 05BTUs hr 76 82 W or 262 12BTUs hr 79 69 W or 271 91BTUs hr col encapsulation IEEE 802 3ae 10 Gigabit Ethernet IEEE 802 3z Gigabit Ethernet IEEE 802 1p QoS COS IEEE 802 1Q VLAN Tagging IEEE 802 1 AB Link Layer Discovery IEEE 802 3ad Link Aggregation with LACP IEEE 802 3x Flow Control Per Priority Flow Control Virtual lanes support Jumbo Frames support Environmental
5. 8 About this Manual This manual describes the installation and basic use of Mellanox BridgeX MBX5020 Gateway products and development platforms based on the MT68102 BridgeX gateway device Intended Audience This manual is intended for users and system administrators responsible for installing and setting up BridgeX gateways from InfiniBand to Ethernet fabrics and networks The manual assumes familiarity with the InfiniBand Architecture Specification as well as the Ethernet Architecture Related Documentation Additional documentation available from Mellanox is provided in Table 2 Table 2 Reference Documents BridgeX Programmer s Reference Manual _ User guide describing the interface used by developers to write a driver Document 2936PM between system software and the Mellanox BridgeX device FabricIT BX Management Software CLI User manual describing the software interface including examples for using User s Manual the BX manager and for installing EoIB and FCoE Host stacks www mellanox com gt Products gt Gateway Software gt Software and Docu mentation Download You willneed a valid Mellanox Gateway S N Mellanox Firmware Tools MFT User s The MFT Mellanox Firmware Tools package is a set of firmware tools The Manual manual supplied with this package provides an overview of the firmware its Document 2329 installation and replacement The MFT can be downloaded with its documen tation at www mellano
6. A fault in the system most likely the firmware did not BOOT properly Red Major Error Possible damage can result to the gateway Turn off immediately For example bad FW can t boot or overheated Note When the system is turned on the red LED will light up for up to two minutes until the CPU is up and running Off Off The system has no power Ifthe STATUS LED shows red after five minutes unplug the gateway and call your Mellanox representative for assistance Ifthe FAN LED shows red troubleshoot the fan module Ifthe gateway shuts down due to over temperature unplug the gateway wait 5 minutes and replug in the gateway 2 2 6 2 Fan Status Indicators The fan unit is located in the center of the power side panel The fan unit has a single 2 color LED to the right of the fan that indicates the internal status of the unit An identical indicator labeled Fans is located on the left side of the connector IB ETH side panel The following fan status conditions are possible Table 8 Fan LED Configurations LED Configuration Fan LED Description Green OK The system is up and running Mellanox Technologies 17 Rev 1 8 Installation and Basic Operation Table 8 Fan LED Configurations LED Configuration Fan LED Description Red Error One or more fans is not operating properly The system should be powered down and troubleshoot the fan module Off Off
7. E oo EY XXI xx roe EE E EE 33 EE 53 EE TA 477 x XX 11 XX II XX XI Pe EF XX IX XX IX XX IX XI 11 II 11 xr II 11 II 11 11 11 XX xr 11 11 II II II xr xr xr xr xr IA DA pa Da pa DA Da DA pa XI Mellanox Technologies 35 Rev 1 8 Installation and Basic Operation Figure 23 Fan Unit Pulled Out Power Side Fan Unit 1 Using two hands push both latch releases in simultaneously while pulling the fan module out of the gateway As the fan unseats the fan status indicator will turn off 2 Pull the fan unit out To insert a FAN Unit Make sure that the new fan unit has the correct air flow direction This can be verified by checking the label on the fan unit and comparing it to the air flow label on the PSU 1 Make sure the mating connector of the new unit is free of any dirt and or obstacles 2 Insert the fan unit by sliding it into the opening until slight resistance is felt Continue press ing the fan unit until it seats completely AN The green fan status indicator should light If not extract the fan unit and reinsert it N N After two unsuccessful attempts to install the fan unit power offthe gateway before attempting any system debug 36 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 3 Management and Software The BX 5020 series gateway contains a management module that gives the user the ability to man age t
8. a redundant power supply you must bring down the system before you replace the PSU Power supply units have directional air flows similar to the fan module The Fan mod ule airflow must coincide with the airflow of all of the PSUs If the PSU airflow direc tion is different from the fan module airflow direction the system will not cool properly 2 4 7 1 To extract a PSU Figure 21 PSU Pulled Out Power Side PSU1 Remove the power cord from the power supply unit 2 Grasping the handle with your right hand push the latch release with your thumb while pull ing the handle outward As the PSU unseats the PSU status indicators will turn off 3 Remove the PSU 2 4 7 2 To insert a PSU 1 Make sure the mating connector of the new unit is free of any dirt and or obstacles N Do not attempt to insert the PSU with a power cord connected to it 2 Insert the PSU by sliding it into the opening until a slight resistance is felt Mellanox Technologies 33 Rev 1 8 Installation and Basic Operation 2 4 8 3 Continue pressing the PSU until it seats completely The latch will snap into place confirm ing proper installation 4 Insert the power cord into the supply connector 5 Insert the other end of the power cord into an outlet of the correct voltage The PSU indicator should light green If not or if it is red repeat the procedure starting with Section 2 4 7 1 Cable Installation All cables can be ins
9. connect each bracket to the gateway If you need room to bring the power cord from the other side of the rack recess the gateway and run the power cord through the bracket The installation kit can be reversed so that the bracket can be installed on either side of the gate ae way the power side or the connector IB ETH side Mellanox Technologies 27 Rev 1 8 Installation and Basic Operation Figure 14 Making Room for the Power Cord Power cord Figure 15 Screwing on the Bracket In this position the front of the gateway is In this position the front of the gate 5cm behind the rack vertical support way is even with the rack vertical sup port il SJ In this position you will In this position you will use 3 flat head screws use 4 flat head screws Se Place to ruh the power cable I The side ofthe gateway with these brackets will be the side that is even with or close to the vertical rack support E 3 Screw the rails onto the gateway Use 5 flat head screws to connect each rail to the gateway Figure 16 Screwing on the Rail 5 screws 4 Clip 4 caged nuts into the holes in the rack you will be using to connect the rail slides Check that both sides of the gateway left and right are the same level in the rack 28 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Figure 17 Clippi
10. connection required 10 VeeR Receiver Ground Common with Transmitter Ground 11 VeeR Receiver Ground Common with Transmitter Ground 12 RD Receiver Inverted DATA out AC Coupled 13 RD Receiver Non inverted DATA out AC Coupled 14 VeeR Receiver Ground Common with Transmitter Ground 15 VecR Receiver Power Supply 44 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Table 14 SFP Pinout Pin Symbol Name Description 16 VecT Transmitter Power Supply 17 VeeT Transmitter Ground Common with Receiver Ground 18 TD Transmitter Non Inverted DATA in AC Coupled 19 TD Transmitter Inverted DATA in AC Coupled 20 VeeT Transmitter Ground Common with Receiver Ground a Circuit ground is internally isolated from chassis ground b Tpaurr is an open collector drain output which should be pulled up with a 4 7k 10k Ohms resistor on the host board if intended for use Pull up voltage should be between 2 0V to Vcc 0 3V A high output indicates a transmitter fault caused by either the TX bias cur rent or the TX output power exceeding the preset alarm thresholds A low output indicates normal operation In the low state the output is pulled to lt 0 8V Laser output disabled on TDIS gt 2 0V or open enabled on TDIS lt 0 8V d Should be pulled up with 4 7kQ 10kQ on host board to a voltage between 2 0V and 3 6V MOD_ABS pulls line low to indi
11. in the status LED may be RED for up to two minutes until the system completes booting up 13 Check the Status LEDs and confirm that all of the LEDs show status lights consistent with normal operation Warning Any yellow or red status LED is cause for concern and must be dealt with immediately 2 4 3 Grounding the Gateway Make sure to connect the ground post to a valid electrical ground Use a grounding lug and a ground wire of sufficient capacity to safely convey a potential discharge A ground wire of AWG 6 or 4mm diameter is recommended for grounding this device The chassis is concurrently grounded through each of the PSUs Only connect the PSU cords to properly grounded outlets Do not rely on the PSU grounds It is absolutely necessary to connect the grounding post Make sure the con nections are solid and permanent If you choose to not use the ground screw make sure that the rack is properly grounded and that there is a valid ground connection between the chassis of the gateway and the rack Test the ground using an Ohm meter Figure 19 Ground Connection SS Check to determine if your local or national electrical codes require an external ground to all IT components Some national and or local codes may require IT components to be bonded and exter A nally grounded not including the power cord ground You must follow all national and local codes when installing this equipment
12. mellanox com gt Products gt Cables for cable recommendations regarding Mellanox approved cables and recommended maxi mum cable lengths 34 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Cables in the bottom row should be inserted up side down in relation to the how the cables are inserted in the top row Figure 22 Top and Bottom Ports 2 4 9 Extracting and Inserting the Fan Unit Operation without a fan unit should not exceed one minute During fan hot swap if the LED indicators are OFF then the fan unit is disconnected The gateway can run on three of the four fans at an ambient temperature of 45 C or less indefi nitely There are two possible air flows for the fan unit The air flow depends on the gateway model An R in the model number indicates a connector IB ETH side to power side air flow See See Part Numbering Legend on page 9 for an explanation of the model numbers and labels Make sure that the fans have the air flow that matches the power units An air flow opposite to the PSUs will cause the gateway to operate at a higher less than optimal temperature To extract a Fan Unit Fan Module Latches 11 xx xr 11 Le xx 11 XX II Xr xr XX Xr II XX XX 11 11 XIX 11 11 Le IIX XIX xr IX xX II 11 xx X x Xx E roe 65 XX XI Xx xx Xr E Xr E XX XI xx EE Xx EY XX XI oo EE Xx
13. per Subnet 320Gb s 42 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Appendix B EMC Certifications B 1 EMC Certifications The list of approved certifications per gateway in different regions of the world is located on the Mellanox Website at www mellanox com related docs user_manuals Regulatory_and_Compliance_Guide pdf EMC Statements are also in the Regulatory and Compliance Guide Mellanox Technologies 43 Rev 1 8 Appendix C Interface Connector Pinouts C 1 SFP Interface Figure 24 SFP Connector Pinout Rear View of Module With Pin Placement oO oc oc E a O FR E A Sr 22 38 88 S D CR D C CD D D D N mM x LO co N O o T T y y a O 00 N de Lo Y ise N o SSS u D D cc n D un 3 lt 2 E dp O a D Q re 3 cc lt T o El L x Q QO x oc O E gt a Table 14 SFP Pinout Pin Symbol Name Description l VeeT Transmitter Ground Common with Receiver Ground 2 TX_Fault Transmitter Fault 3 TX_Disable Transmitter Disable Laser output disabled on high or open 4 SDA 2 wire Serial Interface Data Line 4 5 SCL 2 wire Serial Interface Clock Line 4 6 MOD_ABS Module Absent Grounded within the module Y 7 RSO No connection required 8 RX_LOS Loss of Signal indication Logic 0 indicates normal operation 9 RSI No
14. 02 3ad Link Aggregation with LACP e IEEE 802 3x Flow Control Per Priority Flow Control e Virtual lanes support e Jumbo Frames up to 9K support This feature will be available to customers in the near future Connectors and Cabling e SFP SFP connectors for downlink to 1 GbE ports and to 10GbE ports e Optical transceiver modules for SR and LR for Ethernet Indicators e Per port status LEDs Link Activity Mellanox Technologies 11 Rev 1 8 Overview 1 2 1 3 e System status LEDs system fans power supply e Ethernet indicators for downlink port groups Management Options 2 1000BASE T Ethernet ports Power Supply e Dual redundant slots e 1 PSU is required for device functioning Serial Number and Product Version Information The serial number and product version information are found on the label seen in the figure below The product version information tab location is on the connector IB ETH side of the gateway on the bottom right hand side See Figure 3 on page 12 for a sample of the product label See Figure 1 on page 10 for the product label tab location Figure 3 Generic Product Label S N MT9054X00012 II WML UL I oan PIN MBXS020 1SFC wil ll Made in IL lt x o IL A E D a o o MGT MAC Gateway Port Groups There are four gateway groups in the BX5020 identified as A B C and D Each gateway group consists of one QSFP uplink port and four SFP down link ports Each gate
15. 30 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 2 4 4 Disassembling the Gateway from the Rack To disassemble the gateway from the rack Put on an ESD strap and connect to a valid ground Shut down the gateway using the procedure in Section 2 4 6 Unplug all power supplies Disconnect all cables Disconnect any grounds if hard wired DN ee PNR Unscrew three of the four screws connecting the gateway brackets to the rack Support the gateway while you unscrew the last screw The gateway will drop and could become damaged or it could damage other equipment in the rack 7 While supporting the gateway unscrew the last screw 8 Slide the gateway out of the rails This is easier with two people 9 Remove the rail slides from the other side of the rack See the Mellanox Website for instructions to disassemble the gateway for proper WEEE disposal 2 4 5 Power Connections and Initial Power On The gateway ships with one Power Supply Unit A second PSU can be ordered for redundancy Each supply has a separate AC receptacle The input voltage is auto adjusting for 100 240 VAC 50 60Hz power connections The power cords should be standard 3 wire AC power cords includ ing a safety ground See Table 15 Replacement Parts Ordering Numbers for ordering the cables compatible with the electrical system of your country is no power switch Check all boards power supplies and fan tray modu
16. 54 and for Spanish see Section G Advertencias de seguridad para la instalaci n Spanish on page 37 1 Installation Instructions Read all installation instructions before connecting the equipment to the power source gt 2 Over temperature This equipment should not be operated in an area with an ambient temperature exceed ing the maximum recommended 45 C 113 F Moreover to guarantee proper air flow allow at least 8cm 3 inches of clearance around the ventilation openings gt 3 Stacking the Chassis The chassis should not be stacked on any other equipment If the chassis falls it can cause bodily injury and equipment damage gt 4 Redundant Power Supply Connection Electrical Hazard This product includes a blank cover over the space for the redundant power supply Do not operate the product if the blank cover is not securely fastened or if it is removed gt 5 During Lightning Electrical Hazard During periods of lightning activity do not work on the equipment or connect or dis connect cables Mellanox Technologies 23 Rev 1 8 Installation and Basic Operation 6 Copper InfiniBand Cable Connecting Disconnecting attached to or detached from the connectors Refer to the cable manufacturer for spe Copper InfiniBand cables are heavy and not flexible as such they should be carefully A cial warnings and instructions 7 Rack Mounting and Servicing to ensure that the system
17. Mellanox TECHNOLOGIES BridgeX GT Series BX5020 Gateway IB to Ethernet Hardware User Manual P N MBX5020 1SFR Rev 1 8 www mellanox com Rev 1 8 NOTE THIS HARDWARE SOFTWARE OR TEST SUITE PRODUCT PRODUCT S AND ITS RELATED DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES AS IS WITH ALL FAULTS OF ANY KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PRODUCTS IN DESIGNATED SOLUTIONS THE CUSTOMER S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE PRODUCTO S AND OR THE SYSTEM USING IT THEREFORE MELLANOX TECHNOLOGIES CANNOT AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST QUALITY ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT INDIRECT SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY FROM THE USE OF THE PRODUCT S AND RELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF
18. PSU side airflow F PSU side to connector IB ETH side airflow R RoHS C RoHS5 R RoHS6 Mellanox Technologies 9 Rev 1 8 Overview 1 Overview The Mellanox BridgeX gateway series is a 1U top of rack gateway that provides server I O con solidation over an InfiniBand network The product supports 40Gb s InfiniBand to 1GbE 10GbE Ethernet bridging The BridgeX Gateway is a multi protocol bridge that enables InfiniBand connectivity to native Ethernet networks The gateway implements stateless bridging protocols by encapsulating Ether net over InfiniBand EoIB acting as a packet relay based on read only context Bridging with the gateway requires the use of Mellanox ConnectX or ConnectX 2 adapters on the server to imple ment server side processing of EoIB protocols EoIB capable ConnectX and ConnectX 2 adapters present standard Ethernet Sockets software interfaces to server applications providing transpar ent connectivity for existing Enterprise Data Center EDC and High Performance Computing HPC applications to Ethernet LAN ConnectX and ConnectX 2 adapters also present a standard InfiniBand Verbs software interface to server applications for Inter Process Communication IPC This allows Ethernet and InfiniBand payloads to be carried over a common converged high performance 40Gbps InfiniBand fabric without any changes to existing server applications Data on the converged fabric requiring access to Ethernet LAN is bridged by the gate
19. SUCH DAMAGE Mellanox TECHNOLOGIES Mellanox Technologies Mellanox Technologies Ltd 350 Oakmead Parkway Suite 100 Beit Mellanox Sunnyvale CA 94085 PO Box 586 Yokneam 20692 U S A Israel www mellanox com www mellanox com Tel 408 970 3400 Tel 972 0 74 723 7200 Fax 408 970 3403 Fax 972 0 4 959 3245 Copyright 2012 Mellanox Technologies All Rights Reserved Mellanox Mellanox logo BridgeX ConnectX CORE Direct InfiniBridge InfiniHost InfiniScale PhyX SwitchX Virtual Protocol Interconnect and Voltaire are registered trademarks of Mellanox Technologies Ltd Connect IB FabricIT MLNX OSTM ScalableHPCTM Unbreakable Link UFM and Unified Fabric Manager are trademarks of Mellanox Technologies Ltd All other trademarks are property of their respective owners 2 Mellanox Technologies Document Number 3276 BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Table of Contents Table of Contents 3 List of Tables 5 List of Figures 6 Revision History 7 About this Manual 8 Intended Audience 8 Related Documentation 8 Conventions 8 Gateway Products Covered in this User Manual 9 Mellanox Part Numbering Legend 9 Chapter 1 Overview 10 1 1 Features 11 1 2 Serial Number and Product Version Information 12 1 3 Gateway Port Groups 12 Chapter 2 Installation and Basic Operation 14 2 1 Unpacking the Gateway 14 2 2 BridgeX Gateway Hardware Overv
20. age et entretien sur baie Lorsque ce produit est mont ou entretenu sur baie il faut prendre des pr cautions sp ciales pour s assurer que le syst me reste stable En g n ral il faut remplir la baie avec du mat riel de bas en haut gt Mellanox Technologies 51 Rev 1 8 8 Fuite gt 3 5mA Leakage gt 3 5mA ATTENTION La connexion la terre des forts courants de fuite est essentielle avant le branchement de l alimentation LA Avant de brancher l appareil la conduite d alimentation les vis de protection la terre du terminal de l appareil doivent tre appliqu es l installation de protection la Terre du b timent 9 Forts Courants de Fuite High Leakage Current Attention Forts courants de fuite Il est essentiel de relier a la terre avant de brancher l alimentation 10 Ajouter une information de connexion la masse Connect a Valid Ground to this Device terre du terminal de l appareil doivent tre appliqu es l installation de protection la Avant de brancher l appareil la conduite d alimentation les vis de protection la A Terre du b timent 11 Installation du mat riel h Ce mat riel ne doit tre install remplac ou entretenu que par du personnel form et qualifi 12 Elimination du mat riel L elimination de ce mat riel doit s effectuer dans le respect de toutes les l gislations et r glementations nationales en vigueur 13 Codes l
21. ake sure that the male connectors on the module will align with the female connectors inside of the cage Also check that there is no dirt or foreign matter in the module or in the cage Figure 6 Module with Locking Mechanism Closed Mellanox 30 nm ECMNOLOGIES MFM1TO2A SR Lil bs FTLKBS71DIBCL ME il mn YSIA Class 1 21CFR1040 Mellanox 830 nm 2 13 NOLOGIES n ce iin Class 1 21CFR1040 10 LN 104 MADE N MALAYSIA Insert the module into the adapter card module cage Close the locking Mechanism To remove the module from the cage 1 2 Unlock the locking mechanism by opening the handle Pull the module out of the cage 2 2 6 Status LEDs Figure 8 Power and System LEDs Y AM STATUS PSU 1 PSU 2 FAN RST System Status Indicators PSU Status Indicators 16 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 2 2 6 1 System Status Indicators Status indicators are located on the right side of power side panel and on the left side of the con nector IB ETH side panel Both of these system status indicators are three color LEDs display ing the same status on both sides of the gateway The following status conditions are possible Table 7 System Status LED Configurations LED Configuration STATUS System Health LED Description Green OK The system is up and running Yellow Error
22. cate module is plugged in e LOS is open collector output Should be pulled up with 4 7kQ 10kQ on host board to a voltage between 2 0V and 3 6V Logic 0 indicates normal operation logic 1 indicates loss of signal o Mellanox Technologies 45 Rev 1 8 C 2 RS232 to RJ45 Connector Interface Figure 25 RJ45 Connector Pinout CONSOLE Pin 1 RJ45 RTS RJ45 DTR RJ45 TXD GND Pin 8 Looking into the Socket 46 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 C 3 I2C RJ45 Connector Interface Pinout Figure 26 I2C Pinouts PC Pin 1 RJ45 SDA GND GND GND GND RJ45 SCL Pin 8 Looking into the Socket Mellanox Technologies 47 Rev 1 8 C 4 QSFP Connector Pinout Figure 27 QSFP Connector Pinout 20 len GND 12 21 Rx2n Rxin 18 oO 22 Rx2p Rxip er 2 5 GND 16 _ 24 15 Rx4n Rx Xn aaa 14 PP Rx3p HH 13 Gn GND 27 ModPrsl spa 12 11 Zu IntL SEE 10 ES VecTx Vcc Rx 30 Vec1 ResetL 9 31 pode ModSelL 33 Tx3p Tx4p 34 Tx3n Tx4n 5 35 GND GND 4 36 Txip Tx2p 3 H Txin Tx2n 2 38 GND GND 1 48 Mellanox Technologies Rev 1 8 BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Figure 28 Pinout Looking Into the Rear of the Connector and the Front of the Cage Top 18 35 Vi
23. chnologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Appendix H SFP Modules H 1 Product Features Hot pluggable SFP footprint e Maximum link length of 300m on 2000 MHZ km MMF Supports 9 95 to 10 3 Gb s bit rates Power dissipation lt 1W e e Commercial temperature range 0 C to 70 C Single 3 3 Vpower supply Uncooled 850nm VCSEL laser Receiver limiting electrical interface Duplex LC connector e Built in digital diagnostic functions RoHS 6 compliant lead free H 2 Applications 10GBASE SR SW 10G Ethernet H 3 Dimensions 56 50 gt 14 80 13 60 B El Mellanox Technologies MTSFPP SR Module 12 70 IIb E 1 55 0 50 sso T RI 4 ans E alo 11 85 E i i 4 5 a A 2 5 aii 44 95 gt Mellanox Technologies 61 Rev 1 8 H 4 Pin Descriptions Figure 29 Rear View of Module With Pin Placement Top 13 70 133588338 se a bo A a o xx o E g gt 8 u GA Table 16 SFP Pinout Pin Symbol Name Description l VeeT Transmitter Ground Common with Receiver Ground 2 TX_Fault Transmitter Fault 3 TX_Disable Transmitter Disable Laser outpu
24. ckers elnes Netzteils spannungsfrei Um alle Einhi eten spannungsfrei zu machen sind die Netzstecker aller Netzteile zu entfernen ATTENTION Risque de choc et de danger e lectriques Le de branchment d une seule alimentation stabi lise e ne de branch uniquement qu un module Alimentation Sta bilise e Pour isoler com pletement le module en cause Il faut de brancher toutes les alimen tations stabilise es If the Gateway is powered off for any reason without using the proper shut down pro cedure the Flash memory may be corrupted If the Flash memory is corrupted the Gateway may fail to boot Should this happen call your Mellanox representative for assistance To run the gateway through a power cycle 1 Run config reload halt 2 Wait long enough to let the gateway halt and verify there is no ping to it 3 Unplug the power cord Should the gateway fail to boot upon reinsertion of the power cord burn the latest FW image to the Flash memory 32 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 2 4 7 Extracting and Inserting the Power Supply Unit With both power supplies installed in the redundant configuration either PSU may be extracted without bringing down the system N Make sure that the PSU that you are NOT replacing is showing all green for both the PSU and status indicators If your system does not have
25. dicates normal operation In the low state the output is pulled to lt 0 8V c Laser output disabled on TDIS gt 2 0V or open enabled on TDIS lt 0 8V d Should be pulled up with 4 7kQ 10kQ on host board to a voltage between 2 0V and 3 6V MOD_ABS pulls line low to indicate module is plugged in e LOS is open collector output Should be pulled up with 4 7kQ 10kQ on host board to a voltage between 2 0V and 3 6V Logic 0 indicates normal operation logic 1 indicates loss of signal H 5 Power Dissipation Max power dissipation 1 00 W Mellanox Technologies 63
26. e port numbers of the active Ethernet ports 2 2 2 Uplink Ports There is one uplink port per gateway port group This port has a QSFP Connector These connec tors have support for powered cables and media adapter circuits All of the Uplink ports must be InfiniBand 2 2 3 Configuring the Port Gateway Groups See the FabricIT BXM Management Software CLI User Manual for CLI commands to configure the gateway You can also configure the gateway using the WebUI 2 2 4 Making Connections to Other Formats Hybrid CX4 to QSFP cables are supported on the uplink side Transceivers and optical modules are supported on the downlink side e SFP modules for 10GbE e SFP modules for 1GbE Table 6 Available Transceivers and Optical Modules Part Number Form Factor Application Connector Cable Length up to Wavelength MFMITO2A SR SFP Ethernet 10GbE LC LC 300m 850nm MFMITO2A LR SFP Ethernet 10GbE LC LC 10km 1310nm MC3208011 SX SFP Ethernet 1GbE LC LC 500m 850nm MC3208411 T SFP Ethernet 1GbE RJ 45 Base T 100m 99 Only Mellanox Transceivers and Optical Modules specifically designated as verified to work with the gateway are guaranteed to perform gt Mellanox Technologies 15 Rev 1 8 Installation and Basic Operation 2 2 5 Inserting the Optical Transceiver Module To insert the module into the cage 1 2 3 4 Open the module s locking mechanism see Figure 6 and Figure 7 M
27. ectriques locaux et nationaux A Ce materiel doit tre install dans le respect des codes lectriques locaux et nationaux 14 Codes d installation INSTALLATION CODES L appareil doit tre install selon l ancienne version des codes lectriques nationaux du pays Pour l Am rique du Nord l quipement doit tre install conform ment aux sp cifications du Code Electrique National Am ricain et du Code Electrique Canadien 52 Mellanox Technologies J BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 15 Interconnexion des unites INTERCONNECTION OF UNITS Les c bles de branchement l unit RS232 et les interfaces Ethernet doivent tre certi fi s UL de type DP 1 ou DP 2 Note lorsqu il existe dans un circuit non LPS LA Protection contre la surintensit Un appareil de protection r pertori facilement accessible contre la surintensit du circuit de branchement et calibr 20A doit tre incorpor dans le c blage lectrique du b timent 16 Exposition au rayonnement grave Mise en garde l utilisation de commandes ou de r glages ou l ex cution de proc dures autres que ce qui est sp cifi dans les pr sentes peut engendrer une exposition au rayonnement grave PRODUIT LASER DE CLASSE 1 et r f rences aux normes laser les plus r centes CEI 60 825 1 1993 A1 1997 A2 2001 et NE 60825 1 1994 A1 1996 A2 2001 17 S assurer que les enceintes sont appropri e
28. egula tions gt 14 Local and National Electrical Codes This equipment should be installed in compliance with local and national electrical codes 15 Hazardous Radiation Exposure Caution Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure CLASS 1 LASER PRODUCT and reference to the most recent laser standards IEC 60 825 1 1993 A1 1997 A2 2001 and EN 60825 1 1994 A1 1996 A2 2001 16 UL Approved AC Power Cords For North American power connection select a power supply cord that is UL Listed and CSA Certified 3 conductor 18 AWG terminated in a molded on plug cap rated at 125 V 15 A with a minimum length of 1 5m six feet but no longer than 4 5m gt For European connection select a power supply cord that is internationally harmonized and marked lt HAR gt 3 conductor minimum 0 75 mm wire rated at 300 V with a PVC insulated jacket The cord must have a molded on plug cap rated 250 V 10 A 17 Do Not Use The Switch As A Shelf Or Work Space Caution Slide rail mounted equipment is not to be used as a shelf or a work space 18 WEEE Directive According to the WEEE Directive 2002 96 EC all waste electrical and electronic equipment EEE should be collected separately and not disposed of with regular household waste Dispose of this product and all of its parts in a responsible and environmentally
29. erted or removed with the unit powered on To insert a cable press the con nector into the port receptacle until the connector is firmly seated The indicator above each port will light green when the physical connection is established that is when the unit is powered on and a cable is plugged into the port with the other end of the connector plugged into a functioning port After plugging in a cable lock the connector using the latching mechanism particular to the cable vendor When there is data transfer the light will blink green P When installing cables make sure that the latch engages gt Always install and remove cables by pushing or pulling the cable and connector in a straight line with the gateway bs To remove disengage the locks and slowly pull the connector away from the port receptacle The LED indicator will turn off when the cable is unseated Care should be taken not to impede the air exhaust flow through the ventilation holes next to the ports Cable lengths should be used which allow for routing horizontally around to the side of the chassis before bending upward or downward in the rack Cables especially long copper cables can weigh a substantial amount Make sure that the weight of the cable is supported on its own and not hanging from the gateway These gateways are able to support direct attached copper cables optical FC cables and cables with media adapters at various lengths and gauges Check www
30. et Ethernet Connection 2 Connection 1 The following interfaces allow access to the management module 2 2 10 1 CONSOLE RS232 RJ45 Connector This RS232 connection provides access for local management through connection to a host The BX series gateways can be connected to the RJ45 connector of a computer This connection is needed for the initial configuration of the gateway For the initial configuration procedure for the gateway see the Installation Guide 2 2 10 2 MGT Ethernet Connector The gateway has two Ethernet connectors This Ethernet connection provides access for remote management The BX series gateways can be connected to a network through the RJ45 connectors There are two GbE connectors Their MAC addresses can be found on the product version label Mellanox Technologies 21 Rev 1 8 Installation and Basic Operation tab See Figure 3 on page 12 for the location of the tab The two MAC addresses are consecutively numbered Each Ethernet port gets connected to Ethernet switches Ethernet switches must be configured to 10 100 1000M auto negotiation 2 2 10 3 I2C Connector There is an 12C connector on the far left of the power side of the gateway This connector is for FAEs only LA This interface is for troubleshooting and debugging for FAEs only 2 3 Package Contents The package should include all of the following parts e BridgeX Gateway e Installation kit for 19 Rack mounting 1 power cable fo
31. ew into Rear of Connector LPMode Vcc1 RX4p RX4n GND TX2n TX2p GND TX4n TX4p GND ModSelL ResetL VecRx SCL SDA Top 19 35 GND RX3p RX3n GND RX1p RXin GND View into Front of Cage 8 50 49 Mellanox Technologies Rev 1 8 Appendix D Replacement Parts Ordering Numbers Table 15 Replacement Parts Ordering Numbers Part Description Product Number Power Supply Unit PSU connector IB ETH side to Power MIS000053 side airflow This Replacement part is for both the PSU 1 and PSU 2 Power Supply Unit PSU Power side to connector IB ETH MIS000054 side airflow This Replacement part is for both the PSU 1 and PSU 2 Power supply blank MIS000055 Rack installation kit standard depth gateway standard MIS000085 rack Rack installation kit Short gateway standard rack MIS000083 Rack installation kit short gateway short rack MIS000079 Harness RS232 to DB9 2M long cable HAR000028 Fan Unit for Power side to connector IB ETH side air MIS000051 flow Fan Unit for connector IB ETH side to Power side air MIS000082 flow Power cord Type C13 C14 ACC000251 50 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Appendix E Avertissements de s curit d installation French 1 Instructions d installation Lisez toutes les instructions d installation avan
32. eway and Installation Kit Options Gateway and Rack Description Ordering Part Number Standard depth gateway standard rack MIS000085 Short gateway standard rack MIS000083 Short gateway short rack MIS000079 2 4 2 2 Installing the Gateway in the Rack Tools required and customer supplied parts e Phillips Screwdrivers 1 and 2 e Grounding screw ESD Strap e Grounding wire sufficient to reach a valid ground ESD mat Parts included in the rail kit e 2 rails 18 recessed flat head screws e 2 rail slides 8 caged nuts 26 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 8 pan head screws M6 e 2 brackets Place the ESD mat on the floor where you will be working and put on the ESD strap Make 1 sure the ESD strap is touching your skin and that the other end is connected to a verified ground Figure 13 Installation Kit Parts Rail slide Gi FF GF FF GF FF F FF BER Before you install your new gateway unpack the system and check to make sure that all the parts have been sent check this against the parts list Check the parts for visible damages that may have occurred during shipping IN y N LE If anything is damaged or missing contact your customer representative immediately Screw the brackets onto the gateway Use 3or 4 depending on the bracket position flat head 2 screws to
33. friendly way Mellanox Technologies 25 Rev 1 8 Installation and Basic Operation 2 4 2 Mechanical Installation The gateway can be rack mounted for installation in a standard 19 rack Front and back are arbi trary the rack kit can be mounted so that one side is even with the vertical rack support and the other side is recessed into the rack The rack mounting holes conform to the EIA 310 standard for 19 inch racks Take pre cautions to guarantee proper ventilation for air intake at the front of the chassis and exhaust at the rear in order to maintain good airflow at ambient temperature Cable routing in particular should not impede the air exhaust from the chassis The gateway can be either front or rear mounted The notion of front and back is A arbitrary This document uses the terms power side and connector IB ETH side to pe reduce ambiguity 2 4 2 1 Minimum and Maximum Rack Depth for this Gateway This gateway can go into 19 racks whose vertical supports are between 400mm and 800mm apart Be sure to order the installation kit to match your rack Be sure you have the correct installation kit The Installation Kit must be compatible with the gateway standard or short gateway and with the rack short rack or standard rack Table 12 shows the Rack installation kit options There are three possible rack options Make sure that you have the Rack installation kit that fits your needs Table 12 Gat
34. guration PSU LED Description Green OK The Power supply is delivering the correct voltage 12VDC Red Error The PSU is not operational Replace the PSU Off Off There is no power to the system neither PSU is receiving power If one PSU is showing green and the second PSU is unplugged it will show a red indication 2 2 7 Port Connector LEDs Figure 10 Connector Port Identification STATUS 1 i E 2 Psu1 MM els FA psu2 ID Port numbers Port group labels Above the ports are two LEDs one for the upper port and one for the lower port Vv The fol lowing table shows the port status according to the LED indication Table 10 Port Connector LED Assignment LED Configuration Port Connector LED Description Off No power to the port Solid Green Logical link up Flashing Green Data activity flashing speed data transfer speed Orange Physical link up Flashing Orange A problem with the physical link 2 2 8 Reset Button On the connector side panel under the system LEDs is a reset button This reset button requires a tool to be pressed Mellanox Technologies 19 Rev 1 8 Figure 11 Reset Button Press the reset button to reset the main and management CPUs and to delete the existing password Installation and Basic Operation DO NOT use a sharp pointed object such as needle or push pin for pressing the Reset button Sharp objects can cause damage use a flat
35. ha sido ideada para instalar en lugares de acceso restringido gt 3 Sobrecalentamiento No se debe utilizar el equipo en un rea con una temperatura ambiente superior a la maxima recomendada 45 C Adem s para garantizar una circulaci n de aire adecuada se debe dejar como minimo un espacio de 8 cm 3 pulgadas alre dedor de las aberturas de ventilaci n 4 Apilamiento del chasis Los chasis no se deben apilar sobre otros equipos La caida del chasis podria causar lesiones corporales asi como da os al equipo 5 Conexi n de fuente de alimentaci n redundante peligro de descarga el ctrica Este producto incluye una fuente de alimentaci n redundante o en su lugar una vac a Si se dispone de una fuente de alimentaci n vac a no utilizar el producto si su tapa est quitada o no est bien cerrada 6 Cuando hay rayos peligro de descarga el ctrica No utilizar el equipo ni conectar o desconectar cables durante per odos de activ idad de rayos gt 7 Conexi n y desconexi n del cable Copper InfiniBand Dado que los cables de cobre InfiniBand son pesados y no son flexibles su con exi n a los conectores y su desconexi n se deben efectuar con mucho cuidado Para ver advertencias o instrucciones especiales consultar al fabricante del cable gt Mellanox Technologies 57 Rev 1 8 8 Montaje y mantenimiento de bastidores Al instalar o realizar el mantenimiento de este aparato en un bastid
36. he gateway This management module runs Mellanox proprietary software For information regarding the software see the FabricIT BX Management Software CLI User s Manual To access this document download the User Manual from www mellanox com gt Products gt Gateway Software gt Software and Documentation Download You will need a valid Mellanox Gateway S N N This chapter describes the management module and tools available for Out of Band management of the gateway system via FabricIT gt 4 Each Ethernet port gets connected to Ethernet switches These gateways must be configured to 10 100 1000M auto negotiation aa 3 1 FabriclT FabricIT is a software based management system that can be run with either a command line inter face or with a GUI interface The GUI interface can be run through the Web See the FabricIT BXM User Manual for instructions and commands available to manage the gate ways and fabric Mellanox Technologies 37 Rev 1 8 Troubleshooting 4 Troubleshooting As soon as a gateway is plugged in make sure that the green power LEDs on the PSU are on Power supply unit 1 3 If the AC power LED is off check that the power cable is plugged into a working outlet Check that the power cable has a voltage within the range of 100 260 volts AC Remove and reinstall the power cable Replace the PSU The Status green power LED for PSU1 or PSU2 does not come on 1 2 3 4 If
37. iew 14 2 2 1 Downlink Ports 15 2 2 2 Uplink Ports 15 2 2 3 Configuring the Port Gateway Groups 15 2 2 4 Making Connections to Other Formats 15 2 2 5 Inserting the Optical Transceiver Module 16 2 2 6 Status LEDs 16 2 2 7 Port Connector LEDs 19 2 2 8 Reset Button 19 2 2 9 Air Flow 20 2 2 10 Management Interfaces 21 2 3 Package Contents 22 2 4 Gateway Installation and Operation 22 2 4 1 Installation Safety Warnings 23 2 4 2 Mechanical Installation 26 2 4 3 Grounding the Gateway 30 2 4 4 Disassembling the Gateway from the Rack 31 2 4 5 Power Connections and Initial Power On 31 2 4 6 Shut Down Procedure 32 2 4 7 Extracting and Inserting the Power Supply Unit 33 2 4 8 Cable Installation 34 2 4 9 Extracting and Inserting the Fan Unit 35 Chapter 3 Management and Software 37 3 1 FabricIT 37 Chapter 4 Troubleshooting 38 Appendix A Specifications 41 Appendix B EMC Certifications 43 B 1 EMC Certifications 43 Appendix C Interface Connector Pinouts 44 Cl SFP Interface 44 Mellanox Technologies 3 Rev 1 8 C 2 RS232 to RJ45 Connector Interface 46 C3 I2C RJ45 Connector Interface Pinout 47 C4 QSFP Connector Pinout 48 Appendix D Replacement Parts Ordering Numbers 50 Appendix E Avertissements de s curit d installation French 51 Appendix F Installation Sicherheitshinweise German 54 Appendix G Advertencias de seguridad para la instalaci n Spanish 57 Appendix H SFP Modules 61 H 1 Product Features 61 H 2 Applicati
38. les for proper Caution The gateway will automatically power on when AC power is applied There A insertion before plugging in a power cable Warning Any yellow or red status LED is cause for concern and must be dealt with immediately It can take up to 5 minutes to boot up during which time the status LED may indicate red Caution After inserting a power cable and confirming the green system status LED is on make sure that the Fan Status indicator shows green LA If the fan status indicator is not green then unplug the power connection and check that the fan module is inserted properly and that the mating connector of the fan unit is free of any dirt and or obstacles Mellanox Technologies 31 Rev 1 8 Installation and Basic Operation Caution When turning off the gateway use the proper shut down procedure see Sec tion 2 4 6 and make sure ALL LEDS are off to ensure a powered down status You must power down the system to replace the power supply unit when there is only Do not hot swap the power supply if your gateway has only one working power supply one working PSU in the gateway Figure 20 Two Power Inlets Electric Caution Notifications CAUTION Risk of electric shock and energy hazard The two PSUs are indepen dent Disconnect all power supplies to ensure a powered down state inside of the gateway 2 4 6 Shut Down Procedure ACHTUNG Gafahr des elektrischen Schocks Entferrnen des Netzste
39. ng in the Caged Nuts e The caged nuts are separated by po a single space e 5 Clip 4 more caged nuts into the holes in the rack you will be using to connect the brackets Check that both sides of the gateway power side and connector IB ETH side are at the same level in the rack 6 Using two of the bolts for each rail slide install the rail slides Figure 18 Caged Nut Locations The caged nuts are separated by a single space The rail slides are to be installed on the side of the rack where the gateway will be recessed into the rack 7 Tighten the bolts to 9 2 Nm or 81 5 pound inches If the power cable is on this side of the gateway feed the power cable into the slot in the rail slide before screwing it to the vertical support 8 Slide the gateway catching the rail slides into the rails on the gateway If you extended the bracket past the gateway to use the slot for the power cord now is the time to put the power cord through the slot 9 Screw in the bolts into the caged nuts and tighten the bolts to 9 2 Nm or 81 5 pound inches 10 Ground the gateway See Section 2 4 3 for grounding instructions 11 Plug in the power cord 12 You can start connecting all of the cables to the gateway Mellanox Technologies 29 Rev 1 8 Installation and Basic Operation There is no On Off switch on the gateway The gateway will come on when one plug is plugged in When the gateway is plugged
40. nwandfreien Luftstrom zu gew hrleisten 3 Stapeln des Chassis Das Chassis sollte nicht auf andere Ger te gestapelt werden Wenn das Chassis herun terf llt kann es zu Verletzungen und Besch digungen an Ger ten f hren 4 Redundanter Stromversorgungsanschluss Elektrische Gefahr Dieses Produkt verf gt ber eine Abdeckung ber dem Bereich f r die redundante Stromversorgung Betreiben Sie das Produkt nicht wenn diese Abdeckung nicht sicher festsitzt oder entfernt wurde 5 Bei Gewitter Elektrische Gefahr Arbeiten Sie w hrend eines Gewitters und Blitzschlag nicht am Ger t schlieBen Sie keine Kabel an oder ab 6 Anschlie en Trennen von InfiniBand Kupferkabel InfiniBand Kupferkabel sind schwer und nicht flexible Deshalb miissen sie vorsichtig LA an die Anschl sse angebracht bzw davon getrennt werden Lesen Sie die speziellen Warnungen und Anleitungen des Kabelherstellers 7 Rack Montage und Wartung sichtsma nahmen zu ergreifen um die Stabilit t des Systems zu gew hrleisten Im Wenn dieses Produkt in einem Rack montiert oder gewartet wird sind besondere Vor A Allgemeinen sollten Sie das Gestell von unten nach oben mit Ger ten f llen 54 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 8 Ger teinstallation Diese Ger t sollte nur von geschultem und qualifiziertem Personal installiert ausge tauscht oder gewartet werden gt 9 Ger teent
41. object to push the reset button Mellanox A s PS1 PS2 O UID RST This button resets both the CPU of the switch device and the CPU of the management module It thereby resets all of the ports by bringing them down and powering them up when the button is pushed A quick push of this button performs this reset When the button is held down for 15 sec onds the switch is reset and the password is deleted You will then be able to enter without a pass word and make a new password for the user admin 2 2 9 Air Flow 2 0 These gateways can come with two air flow patterns The two patterns are e connector IB ETH side inlet to power side outlet e Power side inlet to connector IB ETH side outlet The air flow is specified in the product model number See Mellanox Part Numbering Legend on page 9 On the PSUs and fan modules the air flow direction can be seen on the power side panel Table 11 Air Flow Direction Picture OPN Designation Description connector IB ETH side inlet to power side outlet Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Table 11 Air Flow Direction Picture OPN Designation Description Power side inlet to connector IB ETH side outlet 2 2 10 Management Interfaces Figure 12 Management Interfaces CONSOLE USB Connector Product Label Ethern
42. oes not come on Check that the Subnet Manager has been started 38 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 The management module does not start 1 Check that the OpenSM has been started Power Cycle the Gateway Ifthe Gateway is powered off for any reason without using the proper shut down pro cedure the Flash memory may be corrupted If the Flash memory is corrupted the Gateway may fail to boot If this happens talk to your Mellanox representative To run the gateway through a power cycle 1 Run config reload halt 2 Wait long enough to let the gateway halt and verify there is no ping to it 3 Unplug the power cord 4 Plug in the power cord Gateway Fails to Boot 1 Reburn the firmware to the Flash memory using the MFT tools The FabricIT BXM last software update did not succeed 1 Connect the RS232 connector CONSOLE to a laptop 2 Push the reset button on the gateway or management module 3 You will have 5 seconds to stop the U Boot by pressing Control B 4 Choose the image to upload Only use image or image 2 U Boot 2009 01 minx1 4 May 12 2010 14 08 15 CPU AMCC PowerPC 460EX Rev A at 1000 MHz PLB 200 OPB 100 EBC 100 MHz Security Kasumi support Bootstrap Option H Boot ROM Location 12C Addr 0x52 Internal PCI arbiter disabled 32 kB I Cache 32 kB D Cache Board Mellanox PPC460EX Board FDEF No 12C ready DRAM
43. ons 61 H 3 Dimensions 61 H 4 Pin Descriptions 62 HS Power Dissipation 63 4 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 List of Tables Table 1 Revision History Table 7 Table 2 Reference Documents 8 Table 3 Gateway Products Covered by this User s Manual 9 Table 4 Part Numbering Legend 9 Table 5 BX5020 Gateway Port Grouping Protocols and Speeds 13 Table 6 Available Transceivers and Optical Modules 15 Table 7 System Status LED Configurations 17 Table 8 Fan LED Configurations 17 Table 9 PSU Status LED Configurations 19 Table 10 Port Connector LED Assignment 19 Table 11 Air Flow Direction 20 Table 12 Gateway and Installation Kit Options 26 Table 13 BX5020 1S Specification Data 41 Table 14 SFP Pinout 44 Table 15 Replacement Parts Ordering Numbers 50 Table 16 SFP Pinout 62 Mellanox Technologies 5 Rev 1 8 List of Figures Figure 1 MBX 5020 Gateway 10 Figure 2 Port Numbering 11 Figure 3 Generic Product Label 12 Figure 4 Example of a Setup Showing a Port Group 13 Figure 5 Gateway System Connector and Power Side Panels 14 Figure 6 Module with Locking Mechanism Closed 16 Figure 7 Module with Locking Mechanism Open 16 Figure 8 Power and System LEDs 16 Figure 9 BX Gateways Power Side Panel 18 Figure 10 Connector Port Identification 19 Figure 11 Reset Button 20 Figure 12 Management Interfaces 21 Figure 13 Installation Kit Parts 27 Figure 14 Making R
44. oom for the Power Cord 28 Figure 15 Screwing on the Bracket 28 Figure 16 Screwing on the Rail 28 Figure 17 Clipping in the Caged Nuts 29 Figure 18 Caged Nut Locations 29 Figure 19 Ground Connection 30 Figure 20 Two Power Inlets Electric Caution Notifications 32 Figure 21 PSU Pulled Out 33 Figure 22 Top and Bottom Ports 35 Figure 23 Fan Unit Pulled Out 36 Figure 24 SFP Connector Pinout Rear View of Module With Pin Placement 44 Figure 25 RJ45 Connector Pinout 46 Figure 26 I2C Pinouts 47 Figure 27 QSFP Connector Pinout 48 Figure 28 Pinout Looking Into the Rear of the Connector and the Front of the Cage 49 Figure 29 Rear View of Module With Pin Placement 62 6 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Revision History Table 1 Revision History Table Date Revision Description Sept 2012 1 8 Changed section 2 2 4 Added transceivers and optical modules Dec 2011 1 7 Added and up to 4096 virtual NICs using LAG Added LACP as a supported feature Oct 2011 1 6 removed D spanning tree in 2 places Added Hardware to the title August 2011 1 5 Added Acoustic numbers August 2011 1 4 Updated Power numbers Added Power as heat in BTUs hr June 2011 1 3 Removed references to FC June 2011 1 2 Minor fixes Feb 2011 1 1 New power numbers New I2C section Sept 2010 1 0 Initial release Mellanox Technologies 7 Rev 1
45. or es preciso adoptar precauciones especiales para garantizar que el sistema se mantenga estable En general en un bastidor los equipos se deben instalar comenzando desde abajo hacia arriba 9 Instalaci n de equipos La instalaci n el reemplazo y el mantenimiento de este equipo estar n a cargo nicamente de personal capacitado y competente gt 10 Asegurar confinamientos adecuados El fabricante del producto final o el usuario final deber n suministrar un confinamiento adecuado para componentes el ctricos y mec nicos y contra incen dio gt 11 Eliminaci n de equipos La eliminaci n definitiva de este equipo se debe efectuar conforme a todas las leyes y reglamentaciones nacionales 12 C digos el ctricos locales y nacionales Este equipo se debe instalar conforme a los c digos el ctricos locales y nacionales gt 13 Cable de alimentaci n homologado por UL y con certificaci n CSA Fuga gt 3 5 mA En conexiones de Am rica del Norte seleccionar un cable de alimentaci n homologado por UL y con certificaci n CSA de tres conductores 16 AWG termi nado en un enchufe moldeado con capuch n de 125 voltios nominal 13 A con una longitud m nima de 1 5 metros pero no m s de 4 5 metros gt En conexiones europeas seleccionar un cable de alimentaci n armonizado internacionalmente y marcado lt HAR gt de tres conductores hilo de 1 0 mm2 como m nimo 300 voltios nominal con cobe
46. r conforme a la versi n m s reciente de los c digos el ctricos nacionales del pa s en cuesti n En Am rica del Norte el equipo se debe instalar de acuerdo con las disposiciones vigentes del C digo El ctrico Nacional de los EE UU y del C digo El ctrico de Canad 16 Interconexi n de unidades Los cables para la conexi n con las interfaces RS232 y Ethernet de la unidad deben estar homologados por UL tipo DP 1 o DP 2 Nota cuando residen en circuito no de tipo LPS Protecci n contra sobrecargas Al cableado del edificio se debe incorporar un disposi tivo de protecci n contra sobrecargas de circuito derivado de f cil acceso con una cor riente nominal de 20 A 17 Exposici n a niveles de radiaci n peligrosos Precauci n el uso de controles o ajustes o la realizaci n de procedimientos distintos de los que aqu se especifican podr an causar exposici n a niveles de radiaci n peligrosos PRODUCTO L SER DE CLASE 1 y referencia a las normas de l ser m s recientes IEC 60825 1 2007 03 y EN 60825 1 2007 Mellanox Technologies 59 Rev 1 8 18 Directiva sobre RAEE Conforme a la Directiva 2002 96 CE sobre RAEE todos los residuos de equipos el c tricos y electr nicos EEE se deben recolectar por separado y no se deben eliminar junto con residuos dom sticos Al deshacerse de este producto y de todas sus partes h galo de una manera responsable y respetuosa con el medio ambiente 60 Mellanox Te
47. r each PSU Black 250v 10a 1830mm C14 To C13 e RS232 RJ45 to DB9 2 meter cable 2 4 Gateway Installation and Operation Installation and initialization of the gateway are straightforward processes requiring attention to the normal mechanical power and thermal precautions for rack mounted equipment The gateway requires programming and configuration to operate as a basic InfiniBand to Ethernet gateway The gateway includes all of the necessary functionality to operate with external standard Subnet Management software This section describes the installation process and basic operation of the gateway Please first read the warnings sub section carefully before carrying on with installation procedures Ifthe Gateway is powered off for any reason without using the proper shut down pro LA cedure the Flash memory may be corrupted If the Flash memory is corrupted the Gateway may fail to boot 22 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 is no power switch Check all boards power supplies and fan tray modules for proper Caution The gateway will automatically power on when AC power is applied There A insertion before plugging in a power cable 2 4 1 Installation Safety Warnings For Safety Warnings in French see Section E Avertissements de s curit d installation French on page 51 for German see Section F Installation Sicherheitshinweise German on page
48. remains stable In general you should fill the rack with equip When this product is mounted or serviced in a rack special precautions must be taken A ment starting from the bottom to the top 8 Leakage gt 3 5mA WARNING High leakage current Earth connection essential before connecting sup LA ply 9 Add GND Connection Before connecting this device to the power line the protective earth terminal screws of this device must be connected to the protective earth in the building installation 10 Installation Codes This device must be installed according to the latest version of the country national electrical codes For North America equipment must be installed in accordance to the applicable requirements in the US National Electrical Code and the Canadian Electri cal Code 11 Interconnection of Units Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL certified type DP 1 or DP 2 Note when residing in non LPS circuit Overcurrent Protection A readily accessible Listed branch circuit overcurrent protec tive device rated 20 A must be incorporated in the building wiring 12 Equipment Installation This equipment should be installed replaced or serviced only by trained and qualified personnel 24 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 13 Equipment Disposal Disposal of this equipment should be in accordance to all national laws and r
49. rtura protectora aislante de PVC El cable debe tener un enchufe moldeado con capuch n de 250 voltios nominal 10 A ADVERTENCIA Alta corriente de fuga Es esencial efectuar la conexi n a tierra antes de conectar la alimentaci n 58 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 14 A adir conexi n a tierra Antes de conectar el dispositivo a la l nea de alimentaci n los tornillos del terminal de la puesta a tierra de protecci n del dispositivo se deben conectar a la puesta a tierra de LA proteccion de la instalacion del edificio Informaci n de conexi n a tierra La instalaci n del edificio deber prover un medio para la conexi n con la puesta a tierra de protecci n y un t cnico de servicio deber conectar permanentemente el equipo a dicho medio de conexi n Un T CNICO DE SERVICIO comprobar si la toma el ctrica de la que se suminis trar corriente al equipo provee una conexi n con la puesta a tierra de protecci n del edificio De no ser as el T CNICO DE SERVICIO se encargar de instalar un CON DUCTOR DE CONEXI N A TIERRA DE PROTECCI N del terminal de puesta a tierra de protecci n separado al conductor de tierra de protecci n del edificio El equipo se instalar en un rea donde haya conexi n equipotencial como por ejemplo un centro de telecomunicaciones o una sala de computadoras dedicada 15 C digos de instalaci n Este dispositivo se debe instala
50. s Des enceintes lectriques m caniques et incendie adapt es doivent tre fournies par le fabricant du produit final ou par l utilisateur final 18 Cordons lectriques CA homologu s UL Pour les prises lectriques en Am rique du Nord choisissez un cordon lectrique homologu UL et certifi CSA LA 3 conducteurs 18 AWG termin par une fiche moul e d une tension nominale de 125 V 15 A avec une longueur minimale de 1 5 m 6 pieds et d une longueur maxi male de 4 5 m 18 pieds Pour les prises lectriques en Europe choisissez un cordon lectrique harmonis inter nationalement et marqu lt HAR gt 3 conducteurs d un diam tre de fil minimum de 0 75 mm2 d une tension nominale de 300 V avec une gaine isol e en PVC Le cordon doit avoir une fiche moul e d une tension nominale de 250 V et d une intensit nominale de 10 A Mellanox Technologies 53 Rev 1 8 Anhang F Installation Sicherheitshinweise German 1 Installationsanleitungen Lesen Sie alle Installationsanleitungen bevor Sie das Gerat an die Stromversorgung anschlieBen 2 Ubertemperatur Dieses Ger t sollte nicht in einem Bereich mit einer Umgebungstemperatur ber der maximal empfohlenen Temperatur von 45 C 113 F betrieben werden Es ist ein Luft LA strom von 200 LFM bei maximaler Umgebungstemperatur erforderlich AuBerdem sollten mindestens 8 cm 3 in Freiraum um die Bel ftungs ffnungen sein um einen ei
51. sent check this against the parts list Check the parts for visible damage that may have occurred during shipping If anything is damaged or missing contact your customer representative immediately See the package contents in Section 2 3 BridgeX Gateway Hardware Overview The figures below show dual hot swap power supplies 1 I2C connector various status LEDs and the hot swap fan module on the power side The RS232 CONSOLE 2 Management GbE connec tors one USB connector and various status LEDs on the connector IB ETH side Figure 5 Gateway System Connector and Power Side Panels Power Side Connector IB ETH Side A A A lt A YA A A A lt B va A A A lt C MGT CONSOLE vA ZN A A lt D 2 3 4 5 2 3 4 5 2 3 4 5 4 5 NN ON ER 5 er 5 EE W All connectivity is via the connector panel All connectors can support active cables 14 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 2 2 1 Downlink Ports There are four downlink ports per gateway port group These ports support SFP SFP cables and transceivers 9 Only Mellanox Transceivers and Optical Modules specifically designated as verified to work with the gateway are guaranteed to perform gt When configured for Ethernet only 3 of the 4 downlink ports per gateway group are used and all downlink ports within the gateway group must have the same speed that is 1Gbps or 10Gbps See Table 5 for th
52. sorgung Die Entsorgung dieses Ger ts sollte unter Beachtung aller nationalen Gesetze Bestim mungen erfolgen 10 Regionale und nationale elektrische Bestimmungen Dieses Ger t sollte unter Beachtung der regionalen und nationalen elektrischen Bestimmungen installiert werden 11 Richtigen Schutz sicherstellen Geeigneter elekrischer mechanischer und Feuerschutz sind vom Hersteller des Endprodukts oder dem Endbenutzer bereitzustellen 12 Strahlenkontakt Achtung Nutzung von Steuerungen oder Einstellungen oder Ausf hrung von Proze duren die hier nicht spezifiziert sind kann zu gef hrlichem Strahlenkontakt f hren Klasse 1 Laserprodukt und Referenzen zu den aktuellsten Lasterstandards ICE 60 825 1 1993 A1 1997 A2 2001 und EN 60825 1 1994 A1 1996 A2 2001 13 UL und CSA Certified Netzkabel UL Listed and CSA Certified Power Supply Cord F r Nordamerika Stromanschluss w hlen Sie ein Netzkabel das UL und CSA Certi fied 3 Leiter 18 AWG mit einem angespritztem Stecker bewertet bei 125 V 15 mit einer Mindestl nge von 1 5 m Six Feet aber nicht mehr als 4 5 m F r die europ ischen Zusammenhang w hlen Sie ein Netzkabel das international harmonisiert und der Aufschrift lt HAR gt 3 Leiter mindestens 0 75 mm2 Draht bewertet mit 300 V mit einem PVC Mantel isoliert Das Kabel muss eine angespritztem Stecker bewertet bei 250 V 10 A Mellanox Technologies 55 Rev 1 8
53. t de brancher le mat riel la source d alimentation lectrique 2 Temp rature excessive Ce mat riel ne doit pas fonctionner dans une zone avec une temp rature ambiante d passant le maximum recommand de 45 C 113 F Un flux d air de 200LFM cette temp rature ambiante maximale est n cessaire En outre pour garantir un bon coulement de l air laissez au moins 8 cm 3 pouces d espace libre autour des ouver tures de ventilation gt 3 Empilage du ch ssis Le chassis ne doit pas tre empil sur un autre mat riel Si le chassis tombe il peut pro voquer des blessures corporelles et des d gradations de biens gt 4 Connection d Alimentation electrique excedentaire dangers lectriques Ce produit comporte un couvercle transparent sur l espace pour l alimentation lec trique redondante Ne pas faire fonctionner le produit si le couvercle transparent n est pas solidement fix ou s il est enlev A 5 Orages dangers lectriques Pendant un orage il ne faut pas utiliser le mat riel et il ne faut pas brancher ou d brancher les cables 6 Branchement d branchement des c bles InfiniBand en cuivre Les cables InfiniBand en cuivre sont lourds et ne sont pas flexibles il faut donc faire tr s attention en les branchant et en les d branchant des connecteurs Consultez le fab ricant des cables pour connaitre les mises en garde et les instructions sp ciales gt 7 Mont
54. t disabled on high or open 4 SDA 2 wire Serial Interface Data Line 5 SCL 2 wire Serial Interface Clock Line 4 6 MOD_ABS Module Absent Grounded within the module 4 7 RSO No connection required 8 RX_LOS Loss of Signal indication Logic 0 indicates normal operation 9 RSI No connection required 10 VeeR Receiver Ground Common with Transmitter Ground 11 VeeR Receiver Ground Common with Transmitter Ground 62 Mellanox Technologies J BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Pin Symbol Name Description 12 RD Receiver Inverted DATA out AC Coupled 13 RD Receiver Non inverted DATA out AC Coupled 14 VeeR Receiver Ground Common with Transmitter Ground 15 VecR Receiver Power Supply 16 VecT Transmitter Power Supply 17 VeeT Transmitter Ground Common with Receiver Ground 18 TD Transmitter Non Inverted DATA in AC Coupled 19 TD Transmitter Inverted DATA in AC Coupled 20 VeeT Transmitter Ground Common with Receiver Ground Circuit ground is internally isolated from chassis ground b Tpaurr is an open collector drain output which should be pulled up with a 4 7k 10k Ohms resistor on the host board if intended for use Pull up voltage should be between 2 0V to Vcc 0 3V A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceed ing the preset alarm thresholds A low output in
55. the LED on the PSU is off check that the Sys is off Remove and reinstall the power cable Check that the power outlet in the wall is working Remove and reinstall the PSU Make sure the mating connector of the new unit is free of any dirt and or obstacles Replace the PSU The power LED for the gateway shuts off 1 2 Check that the there is adequate ventilation Make sure that there is nothing blocking the front or rear of the chassis and that the fan mod ules and ventilation holes are not blocked especially dust over the holes Use the FabricIT BXM manager to check the temperature of the gateway If you find dust blocking the holes it is recommended to clean the fan unit and remove the dust from the front and rear panels of the gateway using a vacuum cleaner The green power LED for the fans does not come on 1 2 Check that the Power LEDs are on Remove and reinstall the fan unit Make sure the mating connector of the new unit is free of any dirt and or obstacles LA Caution Do not run the gateway if the System Status LED for the Fans is Red The link LED for the connector does not come on 1 2 3 4 Check that both ends of the cable are connected Check that the locks on the ends are secured Make sure that the latest FW version is installed on both the HCA NIC cards and the gate way If media adapters are used check that the all connections are good tight and secure The activity LED d
56. way group can be inde pendently configured Within each gateway group the QSFP uplink ports can be either 10Gbps 20Gbps or 40Gbps InfiniBand and the SFP downlink ports can be either 1Gbps or 10Gbps Ethernet 12 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 EN EN Downlinks Uplink IB Table 5 BX5020 Gateway Port Grouping Protocols and Speeds Gateway Group A EN EN Downlinks Uplink 18 10Gbps 10Gbps 10Gbps unused EN 10Gbps 10Gbps 10Gbps unused 1Gbps 1Gbps 1Gbps unused EN 1Gbps 1Gbps 1Gbps unused Uplink 10 20 40 Gbps 18 10 20 40 Gbps Gateway Group B Gateway Group D 10Gbps 10Gbps 10Gbps unused EN 10Gbps 10Gbps 10Gbps unused 1Gbps 1Gbps 1Gbps unused EN 1Gbps 1Gbps 1Gbps unused Uplink 10 20 40 Gbps 18 10 20 40 Gbps Mellanox Technologies 13 Gateway Group C Port protocol and speed Figure 4 Example of a Setup Showing a Port Group Ethernet 1 2 3 4 5 6 T 1 2 4 5 6 7 8 mann AIR A Ce n g 1 2 3 4 5 6 Y 8 Downlink ee PA m Gateway QSFP Cable Rev 1 8 Installation and Basic Operation 2 2 1 2 2 Installation and Basic Operation Unpacking the Gateway Before you install your new BX5020 unpack the system and check to make sure that all the parts have been
57. way preserving existing LAN investments and management practices The BridgeX gateway along with ConnectX and ConnectX 2 adapters converge different networks onto a single fabric reducing the number of adapters cables and switch ports by a factor of three and reducing capital expenditure The high port density of the gateway within a 1U form factor low power consumption and ease of management also reduces operating expenses Figure 1 MBX 5020 Gateway A A A lt A va A A A lt B va A lt D MGT CONSOLE A A 2 3 4 5 2 3 4 5 2 3 4 5 i cae E Ea Exa Port groups Product version information tab location 10 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 Figure 2 Port Numbering 1 1 Features The BridgeX Gateway series has the following features Uplink ports e 4 ports of 40 G InfiniBand QSFP Downlink ports 12 ports of 1 GbE 10 GbE Ethernet e Down link ports are configured in groups of 3 Down link ports within a group must run the same protocol e A down link port group running Ethernet must run the same speed on all ports within the group 10Gbps or 1Gbps 1024 virtual NICs per Ethernet port and up to 4096 virtual NICs using LAG Total of 16 000 MAC addresses Ethernet ports EEE 802 3ae 10Gigabit Ethernet support e IEEE 802 3z Gigabit Ethernet e IEEE 802 1p QoS COS IEEE 802 1Q VLAN Tagging e IEEE 802 1AB Link Layer Discovery IEEE 8
58. x com gt Support gt Download Firmware Tools Conventions The terms uplink internal and downlink external are used throughout the document Uplink refers to the server switch facing ports where InfiniBand IB is used Downlink refers to the Local Area Network LAN switch facing ports where Ethernet EN are used LA Caution This symbol indicates the possibility of physical injury to the user or installer 8 Mellanox Technologies BridgeX BX5020 Gateway IB to Ethernet Hardware User Manual Rev 1 8 P This symbol indicates information that is helpful to the user gt Gateway Products Covered in this User Manual Table 3 Gateway Products Covered by this User s Manual Family Product Number Description BridgeX IB Gateways BridgeX IB system dual controllers 4 QSFP uplink ports and 16 MBX5020 SFP downlink ports with CPU RoHS6 Mellanox Part Numbering Legend Table 4 Part Numbering Legend Place Field Decoder M Mellanox Technologies BX System Type BridgeX based Bridge System 1 Gateway protocols 1 Ethernet Uplinks 5 InfiniBand Uplinks 9 VPI Ethernet and InfiniBand Uplinks 0 For future use 2 of BridgeX devices 1 For future use 2 2 BridgeX devices 0 For future use Separator 1 Power Supplies 1 1 2 2 Depth of the Unit S standard depth B For future use Y Air Flow direction R connector IB ETH side to

BridgeX GT Series BX5020 Gateway IB to Ethernet

Contents

Download Pdf Manuals

Related Search

Related Contents