Leadenhall Collection Credenza Model
Contents
1. Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 11 Factory No 15548 Model JCS110245 D Assembly Instructions 24 Pick up Keyboard Tray Slides V and W and separate the Slide Runners for later step Extend the Slide Runner all the way forward Press the plastic release lever of the slides up and pull the Slide Runner complete out 25 Attach separated Slide Tracks to the Left Pedestal Right Panel C and Right Pedestal Left Panel E respectively with three M3 5 x 12 mm Pan Head Screws 9 per slide track Ensure the opening of Slide Track facing front of the unit 26 Insert and screw four Cam Bolts 2 all the way into the designated small holes on Left Pedestal Right Panel C and Right Pedestal Left Panel E as shown in the illustration Slide opening 27 Attach Modesty Panel L between the assembled Left and Right Pedestal using four Cam Locks 1 and two Large Wood Dowels 3 Refer to page 2 on Cam Lock system operation supplement Make sure the long edge with holes of Modesty Panel is up Cam Locks point toward back of unit Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 12 Factory No 15548 Model JCS110245 D Assembly Instructions 28 Separate the Back Cover from the Power Center 21 and set aside for later use 29 Feed the USB cable and wire of Power Center 212. LOT NUMBER W DATE PURCHASED Leadenhall Collection Credenza Model JCS110245 D Credenza with Hutch Configuration Hutch sold separately ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS SHARP POINTS SHARP EDGES AS RECEIVED If you have any questions regarding assembly or if parts are missing DO NOT return this item to the store where it was purchased Please call our toll free customer service number and have your instructions and parts list ready to provide the model name part name or factory number 1 866 942 5362 Pacific Standard Time 8 30 a m 4 30 p m Monday Friday Or visit our web site 24 hours a day 7 days a week for product assistance at www whalenfurniture com Or e mail your request to parts whalenfurniture com THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION PLEASE READ AND KEEP FOR FUTURE REFERENCE Whalen Furniture Mfg Inc Page 1 Factory No 15548 Model JCS110245 D Important Before you begin Open identify and count all parts prior to assembly Lay out parts on a flat and non abrasive surface You will need the parts identified on page 5 and 6 of this instruction manual NOTE IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH Insert Dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY HOW THE KNOCK DOWN KD ASSEMBLY SYSTEM WORKS
3. dS cv d Svc0l L SOD OO LF G Stc01L SOP SSd61 XxX IN 0r q Shc0L L SO SHdvVIXSW 6E C SVCOLLSOP SHde XF EW 8E C Src0L SOP S8EXGW ZE d Svc0l LSOPr SOEXSW 9E C S7c0l LSOP Sada XS EW SE d S7c0l SO SZoLXG EW VE G SVCOLLSOP GMS tt d Svc0llSOr GM 1 c amp d Svc0l SOP gdO0 l d Src0lLlLSOr 10 0 C Svc0lL SOPs YSu 6 e d Svc0l SOP YS1 8 0 Svc0LLSOr 1Su 2 e d Svc0lL SOP cf 39811 Dp IS 427 S pl s Bly Aes Pueoghey S pl S 4497 Aes pueoghsy qouy J00q pueH JOMeIG woog 19me1q p S 44i Jemesq p S 497 Jemesq jJOUeY YOR JOMEIG JUOJ4 JOMEIG joued J00q 1luBlu joueY JOOG 49 jays a qeisnipy Aes pseoghey joued Alsepoy BulploN apis Woyog Bulpjoyy luoij tuuollog 1eqssioO pDINA I8upq woog els p q Jjoued yoeg 1uBiu p S 1ybly jelseped 1uBiu p S 497 elseped 1uBiu joued 10688 497 p S 1uBiti Iels p d 497 p S 47 Iels p d 497 do yseq d SrZ0L SOP ezu p uO uollo lloO eyu pes AO 1Hg LSI SHL ASN ASVA Td SLYVd ANV YACHO O L GSAN NOA di 1S1 92 d SV20LLSOP SULy Se d S7c0lLLSOP SILY ve C Svc0lL SOP Md e d Svc0l kSOPr Hd c e d Svc0l lSOPr dd t e d Svc0l Sor Sud 0 e d Svc0l SOP 10 61 G Sv7c0lL SOP ddd 8l d Src0llSOr 4d0 Z1 d Svc0llLSOPr dduy 9l d Svc0llSOr dd1 St d Svc0lLlSOr SV Vl d Svc0LLSOP Ly 1 d Svc0L SOPs dW cl d Svc0lLLSOr WSd ll d S7c0lLlLSOr WAd 01 d S7c0l SOP O
4. Into the middle 7 2 E 4 large hole of the Bottom Front Molding J and attach 2 pea 1 L to one Pedestal Bottom Panel H using 2 Cam Locks 1 aka J p a r Refer to page 2 on Cam Lock system operation s S j ok supplement Make sure the Cam Locks will face floor I 2d p Repeat the same procedure with the other Bottom Front Molding J and Pedestal Bottom Panel H Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 10 Factory No 15548 Model JCS110245 D Assembly Instructions 20 Pick up assembled Bottom Panel H and attach to the Left Pedestal Left Panel B using one Large Wood Dowel 3 and two Cam Locks 1 Make sure the bottom edges are flush with each other Proceed to secure the Bottom Front Molding J in place by screwing one M3 5 x 12 mm Pan Head Screw 9 through the Plastic Connector 14 21 Align and attach one Middle Crossbar I to the Left Pedestal Left Panel B using one Large Wood Dowel 3 and one Cam Lock 1 Ensure the Cam Locks point towards bottom of unit 22 Repeat last two steps with Right Pedestal Right Panel F ean 2 2 lt Le gt g A xX Hf fy SS Ji 23 Repeat the same procedure to attach Left Pedestal Right Panel C and Right Pedestal Left Panel E to the other end of last assemblies respectively lt A a axa J aa 9 k we e aie
5. QUALITY GUARANTEE We are confident that you will be delighted with your Whalen Furniture purchase Should this product be defective In workmanship or materials or fail under normal use we will repair or replace it for up to one 1 year from date of purchase Every Whalen Furniture product is designed to meet your highest expectations We guarantee that you will immediately see the value of our fine furniture This warranty gives you specific legal rights and you may also have other rights which vary from province to province state to state Customer Service 1 866 942 5362 8 30 a m 4 30 p m PST Monday to Friday www whalenfurniture com Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 16 Factory No 15548 BIEMPIEH 891 9 duuoo LOO1N AN 49 U99 Jamo BuiH 100q u q dn uono anin 10 09 01d JOO M S WW ZZ Og s PUeH JOYyOeJG INSEld 1O 9 uuoo ISed uld 9US dey weg MaJOS yUeUS uiy ww 64 X EN N 19S peoH ued WW p4 X SN M S PROH ULed WW Z X FEN M S WU 8E X GN M S WW 08 X GIN M S 2p g WW ZL X FEN M S UIZ WU Z X FEN IS AOG POO M IEWS jamoq poom 86161 Og WED yoo wey JOUUNY plis 14y JOUUNY pl S 497 39811 apis 1uBiti kuu HO d Svc0lL SOP Od lS C Sv20lLlLSOr Hd 0S 0 Svc0l SOP dNL 67 d S7c0l SOP S 8r qQ Shc0l SOD dj Zv d Svc0lL SOP Scec 9b C Svc0LLSOP gH Sr Q Src0L l SOD qd rr Q Shc0l L SOT Od rF Q Shc0L L SOD
6. Screw Cam Bolt into the pre drilled small holes on panel Connect both panels together making sure Cam Bolt goes into pre drilled hole on the end of panel with Cam Lock 3 Insert Cam Lock into pre drilled large hole on panel Make sure arrow on Cam Lock is pointed toward Cam Bolt 4 Once Cam Bolt is connected inside Cam Lock take a Phillips screwdriver and tighten Cam Lock clockwise 5 Plug Cam Cap into the cross slot of the Cam Locks to conceal the cam NO You are now ready to assemble the KD unit Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 2 Factory No 15548 Model JCS110245 D FURNITURE POWER DISTRIBUTION CENTER IMPORTANT SAFETY INSTRUCTIONS Carefully Read all Instructions installing and operating fixture IF YOU HAVE ANY QUESTIONS REGARDING THE PROPER INSTALLATION CONSULT A QUALIFIED ELECTRICIAN WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURE TO PERSONS PLEASE FOLLOW THE NEXT Use only insulated staples or plastic ties to secure the cords Route and secure cords so that they will not be pinched or damage when the cabinet is pushed to the wall Make sure cord is not pinched between cabinet and floor Use the unit for indoor use only Do not use an extension cord to connect this unit to a wall outlet use power strip with integral over current protection to supply other electrical devices or accessories in cabinet This unit must be plugge
7. We recommend attaching back panel with Ring Shank Screws at the corners first Stained surface 34 Using the pilot holes as a guide attach separated Left and Right Slide Runners V and W to the bottom of Keyboard Tray M using four M3 5 x 12 mm Pan Head Screw 9 through the metal tabs Slide opening Finished edge Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 14 Factory No 15548 Model JCS110245 D Left Pedestal Assembling 35 Extend the Ball Bearing Slide Tracks V and W on the pedestal side panels all the way forward including ball bearing cart Align the Slide Runners on the Keyboard Tray M with the Slide Tracks and push the tray carefully inside until it stops NOTE If they do not go smoothly please take out and repeat the step If you need to remove the keyboard tray please pull the tray all the way out then simultaneously push the plastic release lever of the ball bearing slides up on one side and down on the other side and then pull it completely out 36 To insert the assembled storage drawers into place tip the front of drawers down and drop the rollers of the drawers Slide Runners behind the rollers of Slide Tracks on the unit Lift the front of the drawer up and slide it into the unit 37 Extend the Door Hinges 17 and rest the Hinge Cups onto the cutouts of Door Panels O and P Secure the Door Hing
8. choose to use polish test first in an inconspicuous area Using solvents of any kind on your furniture may damage your furniture s finish Never use water to clean your furniture as it may cause damage to the finish Always use coasters under beverage glasses and flowerpots Liquid spills should be removed immediately Using a soft clean cloth blot the spill gently Avoid rubbing Always use protective pads under hot dishes and plates Heat can cause chemical changes that may create spotting within the furniture finish Stains or marks from crayons or ink markers will be difficult to remove In the event that your furniture is stained or otherwise damaged during use we recommend that you call a professional to repair your furniture Check bolts screws periodically and tighten them if necessary Further advice about wood furniture care It is best to keep your furniture in a climate controlled environment Extreme temperature and humidity changes can cause fading warping shrinking and splitting of wood It is advised to keep furniture away from direct sunlight as sun may damage the finish Proper care and cleaning at home will extend the life of your purchase Following these important and helpful tips will enhance your furniture as it ages A Touch up Pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping We hope you enjoy your purchase for many years Thank you for your purchase
9. NY 12 Cam Cap 7 1 extra 13 Shelf Pin 8 14 Plastic Connector 4 15 Plastic Bracket 4 A A ITN lian g A oS ie 16 Floor Protector 8 1 extra 17 Door Hinge 4 18 Drawer Handle 2 19 Door Knob 2 4 L KKK Ka D NNNN WA Vay Ay 20 Handle Bolt 6 21 Power Center 1 22 22 mm Screw 6 1 extra Glue 1 Touch up Pen 1 Tools required Phillips screwdriver and Hammer not provided Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 6 Factory No 15548 Model JCS110245 D Drawer Assembline 1 Unpack the unit and confirm that you have all the hardware and required parts listed 2 Using the pilot holes as a guide align and attach Left Slide Runner DL to Drawer Left Side S using three M3 5 x 12 mm Screws 6 Make sure the roller end of Slide Runner faces backward Tightly fasten with a Phillips screwdriver 3 Repeat last step to attach Right Slide Runner DR to Drawer Right Side T 6 N The edge facing upward o 6 4 Using the pilot holes as a guide attach two Plastic Brackets 15 onto the Drawer Front Q with four M5 x 14 mm Pan Head Screws 10 Be sure the tabs of Plastic Bracket point towards the short end of drawer front vertically 10 N J CoO 7 Sg Zi y o G g aae gt s J Sy 5 G X Ne 2 Please call for replacement pa
10. STEM REQUIRMENTS e Windows 98SE ME 2000 XP Vista 7 e Pentium 233 MHz or higher e At least 64 MB RAM e Available USB port e Mac OS 9 or later for USB 1 1 mode e Mac OS X or later for USB 2 0 mode WARNINGS Your hub automatically shut off any port with a low Or excessive current If USB Hub Current Limit Exceeded appears on your screen disconnect the affected USB device click Reset on the screen and reconnect the device If one of your hub ports is disabled but USB Hub Current Limit Exceeded does not appear e Disconnect and reconnect the affected device e If the port still does not work disconnect the hub and the device and then reconnect Keep your desktop hub dry if it gets wet wipe it dry immediately Do not modify or tamper with your desktop hub s internal components It may cause a malfunction and invalidate its warranty Modifications not approved by the party responsible for compliance could void user s authority to operate the equipment Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 4 Factory No 15548 Parts and Hardware List Model JCS110245 D Please read completely through the instructions and verify that all parts listed are present before beginning assembly e aes Top 1 B Left Pedestal Left Side 1 N N N D Left Back Panel 1 E Right Pedestal Left Side 1 G Right Back Pa
11. W 6 C Svc0lL SOP ddd 8 d Sv7c0l LISO ddu Z2 d Src0l LISO Sddd 9 q Src0l 1 SOD S1du S d Svc0L LSOr dd1 v d Svc0l L SOD SddT1 Gq Shc0L LISO S1d1 d Svc0l LSF 1d d S7c0lL SOP
12. d into a properly grounded outlet The socket outlet shall be installed near the equipment and shall be easily accessible Maximum load of connected equipment cannot exceed a total of 10 amps Do not open or disassemble this unit for any reason SAVE THESE INSTRUCTIONS Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 3 Factory No 15548 Model JCS110245 D Furniture Power Distribution Unit User Guide Please read this user guide before installing and using your power distribution center INTRODUCTION The integrated 3 Port USB 2 0 Desktop Hub offers 480 Mbps high transmission rate and can connect up to three devices such as a digital camera MP3 player cell phone or wireless mouse With plug and play capability you can add a device without restarting your computer INSTALLATION Connect the USB cable to the bottom of the hub and then to your computer The hub installs automatically If necessary follow the onscreen instructions to complete installation Once the default drivers are installed the red LED status indicator light will glow and you can connect devices to the hub NOTES e To reach USB 2 0 high speed your computer or host adapter card must support USB 2 0 This hub is also backwards compatible with USB 1 1 e When using the hub with a computer that has a version 1 1 USB interface all of the devices attached to the hub will run at USB 1 1 speed Product Furni
13. el JCS110245 D Assembly Instructions Using the pilot holes as a guide align and attach two Left Slide Tracks CL to the Left and Right Pedestal Left Side Panels B and E respectively using three M3 5 x 12 mm Screws 6 through the small holes on the Track into place Make sure the roller end of Slide Track facing forward Tightly fasten with a Phillips screwdriver Repeat last step to attach Right Slide Tracks CR to the Left and Right Pedestal Right Panel C and F Insert two Small Wood Dowels 4 into the inner holes of the Bottom Side Molding K and attach to the bottom of Pedestal Side Panels B C E and F using three M5 x 30 mm Screws 7 in each Make sure the bottom edges are flush Screw 3 Cam Bolts 2 into the designated small holes on each Pedestal Side Panel B C E and F as shown in the illustration Gently tap two Floor Protectors 16 onto the bottom of each Pedestal Side Panel B C E and F Make sure the Floor Protectors rest on the center of side panel for avoiding any damage or crack 5 Ge q BC EF lt 6 ao 16 6 Screw 2 Cam Bolts 2 all the way into the designated _ 1 small holes on one Bottom Front Molding J as shown W Unfinished With the pilot holes as a guide fasten two Plastic eae Connectors 14 to the Bottom Front Molding J with the right angle side facing the short end vertically H using M3 5 x 12 mm Pan Head Screws 9 9 Insert one Large Wood Dowel 3
14. es 17 in place by using two M3 5 x 12 mm Zinc Screws 5 in each 38 Pick up the Left Door Panel O and fasten the Hinge Bases onto the Left Pedestal Left Side Panel B with the enclosed self tapping bolts DO NOT fully tighten the bolts 39 Close the Door Panel O to double check the alignment If you find that the door need to be adjusted slightly please refer to the door hinge sticker on the door panel and turn the appropriate screws for a perfectly aligned door After adjusted tighten the screws on Hinge Base to lock the hinges in place 40 Repeat the same procedure to attach Right Door Panel P in place 41 Attach the Door Knobs 19 to the outside of Door Panels using the Handle Bolts 20 provided 42 Put the rubber bumper onto each Shelf Pin 13 Open the door and insert the other end of Shelf Pins in your desired location inside the compartment Make sure you place the Shelf Pins in the same level so the shelf is not tilted Rest the Adjustable Shelf N onto the Shelf Pins installed 43 Plug Cam Caps 12 onto the visible Cams Locks 1 to conceal the Cams eo Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 15 Factory No 15548 Model JCS110245 D Care and Maintenance Use a soft clean cloth that will not scratch the surface when dusting Use of furniture polish is not necessary Should you
15. nel 1 H Pedestal Bottom Panel 2 J Bottom Front Molding 2 K Bottom Side Molding 4 M Keyboard Tray 1 N Adjustable Shelf 2 P Right Door Panel 1 Q Drawer Front 2 C S Drawer Left Side 2 T Drawer Right Side 2 Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 5 C Left Pedestal Right Side 1 F Right Pedestal Right Side 1 e u x I a I Middle Crossbar 2 L Modesty Panel 1 O Left Door Panel 1 AK 4 SSN D g R Drawer Back Panel 2 U Drawer Bottom Panel 2 Factory No 15548 Model JCS110245 D Parts and Hardware List Please read completely through the instructions and verify that all parts listed are present before beginning assembly V Keyboard Tray Left Slides 1 W Keyboard Tray Right Slides 1 CL Left Slide Track 2 CR Right Slide Track 2 DL Left Slide Runner 2 DR Right Slide Runner 2 2 1 Cam Lock 2 Cam Bolt 3 Large Wood Dowel 4 Small Wood Dowel 31 1 extra 31 1 extra 18 1 extra 8 1 extra 5 M3 5 x 12 mm Zinc Screw 6 M3 5 x 12 mm Black Screw 7 M5 x 30 mm Screw 8 M5 x 38 mm Screw 8 1 extra 24 1 extra 12 1 extra 8 1 extra mmn 9 M3 5 x 12 mm Pan Head Screw 10 M5 x 14 mm Pan Head Screw 11 M3 x 19 mm Ring Shank Screw 26 1 extra 8 1 extra 40 2 extra J Se
16. rts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 7 Factory No 15548 Model JCS110245 D Drawer Assembline 5 Connect Drawer Left and Right Side S and T to the Drawer Front Q using four M3 5 x 12 mm Pan Head Screws 9 Make sure the grooves line up with each other Tighten the screws with a Phillips screwdriver Grooves line up with each other and face inward Roller end 6 Slide Drawer Bottom Panel U all the way into the grooves with finished surface up Unfinished Surface J a Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 8 Factory No 15548 Model JCS110245 D Drawer Assembline 7 Fasten the Drawer Back Panel R to Drawer Left and Right Sides S and T using four M5 x 38 mm screws 8 Make sure that Drawer Bottom Panel U fits securely into the groove of the Drawer Back Panel R Tighten all the screws with a Phillips screwdriver 8 Turn the assembled drawer upright 9 Attach one Drawer Handle 18 to the outside of Drawer Front Q using two Handle Bolts 20 provided 10 Repeat the same process to assemble the other drawer Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 9 Factory No 15548 11 13 14 15 Roller is botom 16 17 18 19 Mod
17. through the cutout of the Desk Top A and push Into the cutout from top of Desk Top At the bottom side of top panel fit the separated Back Cover onto the Power Center properly and secure it in place with six 22 mm Screws 22 through the countersunk holes on the Back Cover Make sure the USB cable and wire are not pinched 30 Screw eleven Cam Bolts 2 all the way into the designated small holes on the Desk Top A as shown 31 Insert the six Large Wood Dowels 3 into the top holes of the assembled unit as a guide DO NOT put dowels into the Cam Bolt holes Position Desk Top A onto the inserted Wood Dowels 3 with the Power Center 21 located at back side and attach in place by engaging 11 Cam Locks 1 Refer to page 2 on Cam Lock system operation supplement Please call for replacement parts or assistance 1 866 942 5362 Whalen Furniture Mfg Inc Page 13 Factory No 15548 Model JCS110245 D Assembly Instructions 32 Now go back and tighten all Cam Locks and Screws make sure all the parts are tight and there are no gaps between the parts this will help keep the unit square 33 Align and attach Left and Right Back Panels D and G onto the assembled unit with stained surface facing backward Make sure the margins along all edges of Back Panels are equal Gently hammer the M3 x 19 mm Ring Shank Screws 11 through the pre drilled holes on the Back Panels NOTE
18. ture Power Distribution Unit Model No UE ULO001 Fe Company Whalen Furniture Mfg Inc NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation SY
Download Pdf Manuals
Related Search