User Manual - HSDC Store
Contents
1. 4 5 ON address 3 1 2 ON 3 OFF 4 5 ON Once programmed for the Smoke Detectors and Fire alarm transmitters the receiver automatically as signs each transmitter a location on one of the three RED LED s located on the Front Panel right side The red LED located furthest left of the three is assigned the first Smoke Detector or Fire alarm program The second Red LED the second Smoke Detector or Fire alarm programmed and the third Red LED the third Smoke Detector or Fire alarm programmed Once installed and operating correctly the transmit ters can be identified by location For Example a smoke alarm on LED 1 may represent the bedroom a smoke alarm on LED 2 may be located in the basement and a smoke alarm on the LED 3 may be located in the garage Low battery notification The Silent Call Signature Series Transmitters operates on two AA batteries and has a built in low battery sensor The transmitters will send out a special low battery signal whenever the low battery condition exists When the Sidekick II Signature Series Receiver detects the signal it will display the condition by turn ing on the units ALARM LED and displaying the ALARM ICON along with the CHK ICON For example a smoke detector battery is low The smoke detector or fire alarm transmitter sends a signal to the Sidekick II Signature Series Receiver about its battery condition The receiver will display the FIRE ICON the CHK ICON and turn on the FIRE LED T2. Backup Accessory Battery Backup 12V NI CAD 300mA Compartment amp Connector A 3 ee Battery Backup O Ar x Siz Fi am OnOff IN Switch mead Antenna ch Power Supply Telephone EEN UN Vibrator Jack 1 Terminal Interface Input OX 6 Transmitters When the Sidekick II Signature Series Receiver detects an incoming signal from any of the Signature Series transmitters it will notify you by Transmitter Type Alarm Clock Sound Monitor Transmitter Telephone Transmitter Doorbell Transmitter Door Window Access Transmitter TransMAT Ter Transmitter Weather Alert Transmitter Carbon Monoxide Transmitter Smoke or Fire Transmitter Notification Bell Icon Strobe flashes Vibrator Optional Sound Icon Orange LED Strobe flashes Vibrator Optional Phone Icon Green LED Strobe flashes Vibrator Optional Door Icon Yellow LED Strobe flashes Vibrator Optional Door Icon Yellow LED Strobe flashes Vibrator Optional Door Icon Yellow LED Strobe flashes Vibrator Optional Weather Icon 2nd Red LED Strobe flashes Vibrator Optional CO Icon 2nd Red LED Strobe flashes Vibrator Optional Fire Icon 4th Sth or 6th Red LED Strobe flashes Vibrator Optional See information on Supervision Mode for more information on LED indicators If you are using the optional Bed Vibrator and your Sidekick II Signature Series Receiver detects an incoming signal from any of the Signature Series transmitters
3. along with the above Notifications the bed vibrator will also pulse in a specific way for each transmitter Transmitter Type Pulse Pattern Short Pulse e Long Pulse Alarm Clock Two Short Pulses and One Long Pulse Sound Monitor Transmitter Three Short Pulses Telephone Transmitter One long pulse Doorbell Transmitter Two Short Pulses Door Window Access Transmitter Two Short Pulses TransMATTer Transmitter Two Short Pulses Weather Alert Transmitter One Short Pulse and One Long Pulse Carbon Monoxide Transmitter Three Short Pulses and One Long Pulse Smoke or Fire Transmitter Continuous Short Pulses 7 Transmission Range Transmission range refers to the distance a Silent Call Transmitter can communicate with the Sidekick II Signature Series Receiver Range is measured in an outdoor environment without obstructions from metal objects or buildings The range for the Sidekick II Signature Series Receiver is up to 2000 feet The actual range inside a building will vary depending on many factors outside of one s control Cancelling An Incoming Alert To cancel an alert press and release the mode button once Programming the transmitters All Signature Series Transmitters come pre programmed at the factory You do NOT need this step unless you need to change the address due to someone in your area that has Silent Call products and they are interfering with your equipment OR if you want to use the Super
4. P mode When your alarm is activated the strobe light and bell icon will flash and the bed vibrator optional will shake To turn the ALARM on or off press and release the Alarm Clock button When the alarm is turned ON the BELL ICON will appear on the screen LCD Display The LCD Display screen is back lighted The back light brightness is automatically controlled by the light level in the room When the room becomes dark the back lighting comes on When the room becomes light the back lighting goes off Telephone Direct Interface The Sidekick II Signature Series Receiver has the ability to plug a standard telephone line directly into the receiver using the supplied telephone wire and dual connector and it will notify you each time the telephone rings Plug the dual connector into your phone jack wall outlet Then plug the wire from your telephone into one side of the dual connector Next take the telephone wire that came with your Sidekick II Signature Series Receiver and plug it into the other side of the dual connector See illustration 1 Finally plug the other end of that cable into the back of the Sidekick II Signature Series Receiver See illustration 2 The receiver will notify you in the same way as if you were using a Telephone Transmitter see section on Notifications Illustration 1 a ee Illustration 2 Remove screw to gain access to battery backup compartment 2 AAA Batteries Clock Battery
5. SilentCall COS ot er se potir hd 4 mm Q UTE DE a Sil ici ae Receiver a a Ooeooo n ERAS X 5 Qca SS Signature Series 418MHz Sidekick ll Signature Series Model SK2 SS 418 MHz Receiver Setup and Operation 1 Plug the power supply pin jack into the connector located next to the Power ON OFF switch on the back of the receiver see page 6 for diagram Plug power supply into a wall electrical outlet Battery Back up Installation Instructions Your Sidekick II Signature Series Receiver comes with the battery back up pre installed at the fac tory In the event that you need to re install the battery pack follow the instructions below The battery compartment door is secured by one screw To gain access to the battery compart ment remove the screw pg 6 Plug the female connector from the battery pack onto the male connector pin in the battery compartment Be sure to line up the pins with the holes in the con nector It will only fit one way Replace the battery compartment door and secure the screw You will notice and On Off switch on the right hand bottom corner of the battery compartment door see pg 6 With the battery back up installed and the back up switch turn to the ON posi tion the Sidekick IPs blue light AC power indicator will turn to an amber color when the unit goes into battery back up mode because of a power failure Turning the battery back up power switch to OFF w
6. are in Set Clock Time mode Press and release the minute button to set the minutes Press and release the hour button to set the hour When you are finished setting the minutes and hours press and release the MODE pushbutton three times to exit the Setup Mode NOTE Any time you unplug your Sidekick II Receiver from the wall outlet or turn the power off the next time you turn your Sidekick II Receiver on again you will need to reset the clock If you are using the Battery Backup feature you will not need to do this 6 All of your Signature Series transmitters come pre programmed from the factory to work with your Sidekick II Signature Series Receiver If you need to set your transmitters to a different address please refer to the section in this manual on programming transmitters The only reason you would need to do this is if someone in your area is using Silent Call products and they are interfering with your products or if you want to use the Supervision Capability with your Silent Call Smoke Detectors or Fire Transmitters zeug Alarm Clock Press and release the MODE push button twice The Green LED will light up indicating that you are in the SET UP mode The display will show the present Alarm Clock Time setting Press and release the MINUTES button to set minutes and press and release the HOURS button to set the hours Once the Alarm Clock Time has been set press the MODE button 2 times to exit the SET U
7. de for Smoke and Fire Transmitters The Sidekick II Signature Series is capable of monitoring up to three Silent Call Smoke Detectors and or Fire transmitters for low battery out of range interference from outside sources and missing or failure of the transmitter to communicate with the receiver The MODE is referred to as the SUPERVISOR MODE All 418 MHz Signature Series Silent Call Fire and Smoke Detector transmitters send out a special alarm signal at two minute intervals The receiver will continue to operate in its normal mode provided the unit is receiving the supervisory alarm signals from the Smoke or Fire transmitter The receiver will alert the user if a Smoke Detector or Fire transmitter signal has not been received within a period of 10 minutes When this happens the LCD will flash the FIRE ICON and the CHK ICON for 10 seconds every 30 seconds Also the RED LED that corresponds to the transmitter that is having the problem will light up and that is how you will know which unit is having a problem The Sidekick II Signature Series Receiver automatically enters the supervisor mode once it has been pro grammed for a smoke detector or fire alarm transmitter 9 Each Smoke Detector or Fire alarm transmitter must be assigned an address different from all other transmitters For example if two smoke detectors and one fire alarm transmitters are being used they may be assigned address 1 1 OFF and 2 3 4 5 ON address 2 1 ON 2 OFF 3
8. he unit will not turn on the Strobe or Vibrator The display will continue to show the low battery condition until the problem is resolved Once resolved the transmitter will no longer send the low battery alarm Technical Support For technical support on this or any other Silent Call product please feel free to contact us You can reach us by phone at 800 572 5227 voice or TTY or by Email at support silentcall com Limited Warranty Your Silent Call product is warranted to be free of defects in material and workmanship for five years from the date of initial purchase During that time the unit will be repaired or replaced free of charge when shipped prepaid to Silent Call Communications This warranty is void if the defect is caused by customer abuse or neglect We honor the smoke detector manufacturer s warranty for their smoke detec tor Only Silent Call products are warranted for 5 years 10 11 SilentCall Communications A better way to stay in touch 5095 Williams Lake Road Waterford MI 48329 Phone 800 572 5227 v tty www silentcall com
9. ill turn off the battery back up to the receiver and the clock It is important that the battery back up feature be turned ON for proper operation The Ni Cad battery is intended to keep the Sidekick II operational during a short term power outage for several hours without the strobe or vibrator operating If both strobe and vibrator are operating the battery back up will operate the system for approximately 10 minutes The battery back up is automatically being charged when the Sidekick II power supply is plugged into a stan dard electrical wall outlet The BATTERY ICON will display itself on the LCD screen once the battery back up level has reached 2 3 of its discharge However the BATTERY ICON will not be displayed until this condi tion is reached When the Amber LED is on but the BATTERY ICON is not displayed on the screen this means that the battery is at a full or close to full charge 2 Turn the Power ON by sliding the ON OFF SWITCH on the back of the receiver to the ON position The front panel display will show the time 11 59AM A blue light will be visible from the Strobe lens The blue light indicates that the unit s AC power is on An amber light will appear if the unit is in bat tery backup mode If your unit is equipped with a battery back up 3 Set Clock Time Press and release the MODE pushbutton the large button located at the lower right hand side on the unit The Orange LED will light up to let you know that you
10. s now programmed to work with your receiver 8 11 Repeat the above steps ONLY if the other transmitters are set to a DIFFERENT address setting than the transmitter you just programmed We recommend keeping all of your transmitters set to the same address to reduce interference from other Silent Call systems that may be in your area All Erase Provisions are made to erase all programmed transmitter addresses The only time you would need to use the ALL ERASE feature is if you are receiving signals from another Silent Call System in your area You would then do the ALL ERASE feature on your receiver and then re program your transmitters to a different address The ALL ERASE function is performed as follows 1 Turn off the Sidekick II Signature Series Receiver by turning the AC power switch to the off posi tion Turn back up battery to off position if you have the backup battery installed An indication of power being off would be that the blue and amber light on the strobe lens is off 2 Press and hold the MINUTES pushbutton DO NOT RELEASE THE BUTTON 3 Turn the power back on while holding the MINUTES pushbutton in 4 Once power is on release the MINUTES pushbutton The all erase function is complete and the unit will now need to be re programmed with its transmitters The Supervisor MODE is also disabled Please Remember to program the smoke detectors and fire trans mitters before programming any other transmitters Supervision Mo
11. vision Mode with your smoke detectors 1 Make sure that all Silent Call transmitters in the area are turned off 2 Perform the ALL ERASE function see pg 9 3 Select the transmitter you wish to program with the Sidekick II Signature Series Receiver It is important to program the Smoke Detector and Fire transmitters first because of the supervision capability 4 Located on the back of the transmitter case is a removable access panel Remove the access panel and take out the batteries 5 Locate the switch on the transmitter circuit board that has 5 small dip switches 6 Set the switches to any combination that you want For Example 1 2 On 3 4 5 OFE Do not set them to all ON or all OFF as this can cause interference This gives your transmitter an address Note that you MUST remove the batteries first or the switch set ting will not take effect 7 Reinstall batteries and replace the access panel 8 Make sure that the transmitter is near the Sidekick II Signature Series Receiver 9 On the Sidekick II Signature Series Receiver press and release the MODE pushbutton until the Yellow LED lights up and PPP is displayed on the screen This means you are now in program mode 10 Press the test button on the transmitter so that it sends a signal to the Sidekick II Signature Series Receiver The unit will flash its strobe turn on the appropriate LED and display Icon for the transmit ter that you used Your transmitter i
Download Pdf Manuals
Related Search