Home

QUADRO ELETTRONICO LRx 2074VN

image

Contents

1. now entered programming mode Press the radio control button you wish to use for upward movement and hold it for 5 seconds until the control unit emits a beep to confirm the operation has been carried out Next press the second radio control button which will be used for downward movement and hold it for 5 seconds until the control unit beeps twice to confirm the operation has been carried out successfully After one second the control unit will beep another four times to signal the programming process is finished If the second code is not set immediately after the first the control unit will exit the programming mode and then emit four beeps to signal the programming process is complete It will operate using only one code Programming using a 3 button radio control BeFree Series press the SEL button with the nib of a pen for example on the end of the box you will hear three beeps confirming that the unit has now entered programming mode Press the Up button on the BeF ree series radio control which will control the upward movement and hold it for 5 seconds until the control unit beeps to confirm this function has been set After a second the control unit will beep four times to signal that the programming process is complete PROGRAMMING WITH OTHER Rapio CONTROLS The above programming operations can be repeated to enter further radio control codes up to a maximum of 75 in the control unit memory If the memory alread
2. unit will stop the shutter movement completely If during upward or downward movement a command is sent for the same direction the control unit will keep the motor running If a command which is in the opposite direction to the current movement is sent during the upward or downward movement the control unit will cause the shutter to change direction User Present Operation In this operating mode the command used to control the motor of the blind where the direction of movement depends on the button pressed is constantly enabled The movement stops when the control is released Operation with Indefinite Motor Running Time In this operating mode the control unit is activated for an indefinite period of time when a button on the radio control is pressed unless a further command is sent which leads to its deactivation Group OR GENERAL CENTRALISATION It is also possible to enter two identical codes buttons from one radio control onto all the control units or a group of them which are situated at a maximum distance of 20 metres from the point of command in order to obtain general or partial motion of more than one automation PROGRAMMING THE Rapio CONTROL The transmission codes for a radio control may be programmed as follows Programming using a 1 or 2 button radio control press the SEL button with the nib of a pen for example on the end of the box you will hear three beeps confirming that the unit has
3. MC4 ELECTRONIC CONTROL UNIT An electronic control unit with incorporated radio receiver for the remote operation of rolling window shutters sun blinds and Venetian blinds It may be used together with one or more radio controls for individual or centralised control for the simultaneous manoeuvring of more than one piece of equipment TECHNICAL DATA Power supply Motor output Operating temperature Radio receiver Type of radio control Stored code capacity 230V 50 60Hz 1 5W 230V SOOW Max 10 to 70 C 433 92 MHz 12 18 Bit BeFree Sx or Rolling Code 75 with different codes Container size 102 x 27 x23 mm Container ABS PC VO plastic Protection degree IP 65 BUZZER 11 SH 8 O N1 ContRoL Unit Power SuppLY ConnecTION N Blue 230V line input Neutral F Brown 230V line input Phase T Yellow Green Earth CN2 Motor ConnecTION 1 Yellow Green Earth 2 Black 230V motor output UPWARD MOVEMENT 3 Blue 230V motor output SHARED 4 Brown 230V motor output DOWNWARD MOVEMENT INITIAL OPERATING CONDITION The device can only operate in conjunction with one or more radio controls the central control unit contains no stored radio control codes when it is first used OPERATION USING DIFFERENT MopeLs or Rapio ConTtROL Different models of remote control may be programmed By storing a code one button a cyclic step by step ope
4. e downward movement phase Operation using a 3 button radio control BeFree Series When using a radio control with 3 buttons the following processes may be carried out the Up button controls the upward movement until the motor stops running 3 minutes the Stop button makes the shutter stop and the Down button controls the downward movement If a stop command is sent during the upward or downward movement the control unit causes the shutter to stop If during upward or downward movement a command is sent for the same direction the control unit will keep the motor running If a command which is in the opposite direction to the current movement is sent during the upward or downward movement the control unit will cause the shutter to change direction OTHER OPERATING MODES Venetian Blind Operation In this operating mode when the Up or Down button of a stored radio control is pressed for less than 2 seconds the unit functions in the user present operating mode It is possible in this manner to rotate the slats of the Venetian blind in one direction or the other in order to modulate the amount of light filtering through as desired If the button on the radio control is pressed for longer than 2 seconds the blind moves upwards or downwards depending on which button was pressed until the motor stops running the timer is set to approximately 3 minutes if a Stop command is sent during upward or downward movement the control
5. e operation described above or perform the Reset procedure ESET WITH THE SEL BUTTON To restore the control unit to its default configuration proceed as follows press and hold the SEL button for 5 seconds until the control unit beeps five times to confirm that the operation is complete EEP SIGNALS 1 BEEP First radio control code stored 2 BEEPS Second radio control code stored 3 BEEPS Start of programming phase 4 BEEPS End of programming phase 5 BEEPS Restoration of default configuration 6 BEEPS No more memory available for new codes 7 BEEPS Motor running time programming For THE USER IMPORTANT The device should not be used by children or by individuals with reduced physical or psychological abilities unless supervision is provided or instruction given on how to operate it Do not let children play with the device keep radio controls out of their reach CAUTION Keep this instruction manual in a safe place and adhere to the important safety instructions contained within it Non adherence to these instructions may lead to property damage and serious accidents Examine the system frequently to check for any signs of damage Do not use the device if it needs to be repaired If the wires have to be replaced for the power supply or for the motor output contact a qualified technician only FOR THE INSTALLER IMPORTANT The control unit was designed to enable the installer to auto
6. europ hereby declares that the product below MC4 Comply with the requirements of Directives R amp TTE 99 5 EC EMC 2004 108 EC LVD 2006 95 EC amp PM a FAri inea ttt a an ce i oe Tee i ee A STATEUROP sistemas automatizados para europa S a Rua do Sobreiro Lugar do Pinheiro Rio C vo St Eug nia Apto 5018 EC Barcelos 4754 908 Rev 1 2 21 05 07
7. mate closure while adhering to the provisions set out by current legislation Compliance with these obligations and the implementation of the minimum safety requirements is the responsibility of the installer Once installation has been completed in full compliance with EN 60335 2 97 Household and similar electrical appliances Safety part 2 Particular requirements for drives for rolling shutters awnings blinds and similar equipment make sure that gt There are no accidental movements gt There are no movements which were not requested caused by variations in the voltage and electricity supply gt The force of impact at the main closure edge does not exceed 25 N for more than 5s 150 N for more than 0 5 s If the latter provision is not satisfied the User Present function can be used as an alternative to obtain non self holding release command operation In this case the radio control must only be used while the user is in full view of the rolling device perhaps fixing it to the wall would ensure this We also advise that you take note of the following recommendations For the radio receiver to operate correctly when two or more control units are used we recommend that you install the devices at least 3 metres away from each other The control unit is not equipped with a sectioning device The installer is therefore responsible for the installation of a sectioning device in the system Stat
8. ration Up Stop Down may be achieved and by storing two different codes two buttons different commands are produced one for Up and one for Down Storing three different codes three buttons produces three different commands the first for Up the second for Stop and the third for Down it is also possible to programme the Venetian blind movement Operation using a 1 button radio control The following type of operation is obtained using a radio control with a single button The first press controls the upward movement until the motor stops the motor has a running time of around 3 minutes The second press controls the downward movement of the shutter If the button is pressed before the motor stops running the control unit will stop the shutter moving and the button will need to be pressed again to reactivate the motor in the opposite direction Operation using a 2 button radio control By using a radio control with 2 buttons the following processes may be carried out the first button Up controls the upward movement for about 3 minutes until the motor has stopped running and the second button Down controls the downward movement of the shutter If the upward movement is interrupted with another Up command the motor will continue to run in the upward movement direction If however the movement is interrupted with a Down command the control unit will stop the motor The procedure remains the same for th
9. y contains 75 stored codes when you attempt the programming procedure the control unit will beep six times to inform you that the memory is full Rev 1 2 21 05 07 INVERSION OF THE ROTATION MOTOR If you notice that when pressing the Up key on the radio control the control unit causes the shutter to move downwards instead of upwards simply repeat the programming procedure pressing the Down key instead of the Up key or invert the Upward movement wire and the Downward movement wire of the motor PROGRAMMING VENETIAN BLIND OPERATION To activate this operating mode move the jumper J1 located on the board inside the plastic container from position 2 3 to position 1 2 Perform this procedure with the control unit disconnected from the 230 U lt 2 D Q mmp Q mp lt e2 C Ke j ROGRAMMING User PRESENT BLIND OPERATION To activate this operating mode remove the jumper J1 located on the board inside the plastic container Perform this procedure with the control unit disconnected from the 230 V electricity supply PROGRAMMING INDEFINITE Motor TIME O n D mr c gt 3 a D Q O a O 3 D e O O O D D Q N o O n e O D n on 3 a gt oO a mr J D SEL button while the control unit is connected to the electricity supply until the control unit emits seven confirmation beeps To restore the three minute motor running time repeat th

Download Pdf Manuals

image

Related Search

Related Contents

Électrodes de laboratoire - Télécharger le fichier  Manual de Instrucciones Sierra Caladora  LTRT-61405 MP-1xx Fast Track Installation Guide    Owners Manual • Bedienungsanleitung Manuel de  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.