iMove 50S User Guide
Contents
1. Z Solution Your integrated Solution iMove 50S User Guide Professional Entertainment Technology TABLE OF CONTENTS Safety Instructions Technical Specifications How To Set The Unit How To Control The Unit Troubleshooting Fixture Cleaning 1 Safety Instruction LA Please read carefully the instruction which includes important information WARNING about the installation usage and maintenance e Please keep this User Guide for future use If you sell the unit to another user be sure that they also receive this user manual e Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of the power supply match the power requirements of the unit e It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location e The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked e Disconnect main power before replacement or servicing e Make sure there is no flammable materials close to the unit while operating as it is a fire hazard e Always use a safety cable when installing this unit Don t carry the unit by its head only but always carry it using the base e The maximum ambient temperature is to 40 C Don t operate i2. Lhd gt B Ch Es SPLE gt O0 e othe gt Stl l bid gt no e S nd gt Lon SUSE gt 1 90 Ce 090 gt O0 g HELE gt oO Led gt Len Fud gt E Notice Other settings are NOT changed while choosing Defaults Setting Press the ENTER button and the corresponding functions will set to defaults setting to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode 11A CO kt Reset Press the MENU button to show Ic SPI on the display Press the ENTER button and all channels of the unit will return to their standard position To go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode 3 3 Home Position Adjust MENU In the main functions hold the Enter button for at least 3 seconds into offset mode use the DOWN and UP buttons up to chose offa lot L lot or bobl Pressing the ENTER button and the display will blink Use the DOWN and UP buttons to adjust the home position of the Pan Tilt Color Gobo Once the position has been selected press the ENTER button to setup Hold and press the MENU button for about one second or wait for one minute to exit the menu mode 4 How To Control The Unit You can operate the unit in thr
3. DA CT CO 25 CO CH CO IT U bs CO D m Tr AN UU Self test DMX512 Address Setting Channel Mode Show Mode Split Color Mode Slave Mode Normal Slave Mode 2light show Blackout Mode Yes Blackout Blackout Mode No Blackout Sound Mode on Sound Mode off Sound Sense 0 100 Pan Normal Pan Inversion Tilt Normal Tilt Inversion LED on LED off Normal Inversion Function Delay Os 3s Dimmer Calibrat Temperature test Fixture Hours Software Version CO rc qot Frac PRO Defaults utd AUTO Defaults na Reset 6A CH tt _o D OO DMX 512 Address Setting Press the MENU button to show Fidar on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to change the DMX512 address Once the address has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button ag
4. 0 7 Blackout Ch8 Ch9 Ch10 Ch11 Color Wheel Color Wheel Normal Split Color Mode Gobo R Gobo Function 255 Rotation Fast 255 RotationFast O 250 255 Sound Active 128 Rotation Slow 210 249 No Function 255 Rotation Fast 120 127 Color16 194RotationSlow 255 Rotation Fast 200 209 Reset All E 113 119 Color15 190 193 Stop EEGEN o function 120 129 Disable blackout while Gobo change 110 119 Enable blackout while Gobo change 100 109 Disable blackout while Color change 090 099 Enable blackout while Color change 080 089 Disable blackout while Pan Tilt move 070 079 Enable blackout while Pan Tilt move 000 069 No Function OO BOS 15A 4 5 DMX512 Connection COMMON DMX INPUT Termination reduces signal errors and avoids signal transmission problems and interference Itis always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you are using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At the last unit the DMX cable has to be terminated with a termination plug Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the in
5. mode Ch1 Ch2 Ch3 Ch4 Pan Tilt Shutter Gobo 255r 540 2551 270 248 255 Open 255 Rotation Fast 240 247 Random Siepe 194 Rotation Slow 232 239 open 190 193 Stop Fast Open 189 Rotation Slow 190 231 Siow Close D 182 189 Open 128 Rotation Fast Sid Close 110 127 Gobo7 shaking 140 181 Siow open 101 109 Gobo5 shaking 092 100 Gobo4 shaking 12 140 e 083 091 Gobo3 shaking g 074 082 Gobo2 shaking F 064 073 Gobo shaking 16 131 ee 048 063 Gobo 040 047 Gobo5 E 032 039 Gobo4 Slow 024 031 Gobo3 8 15 open 016 023 Gobo2 o o im 008 015 Gobo1 o 0 0 0 Vi Baeken 000 007 White Ch5 Ch6 Ch7 Ch8 Color Wheel Color Wheel Normal Split Color Mode R Gobo Dimmer Function 255 Rotation Fast 255p 100 250 255 Sound Active 128 Rotation Slow 210 249 No Function 255 Rotation Fast 120 127 Color16 255 Rotation Fast 200 209 Reset All gt RE NO 130 199 No function 128 Rotation Slow 098 104 Color13 194 120 129 Disable blackout 113 127 Color8 090 097 Color12 Rotation Slow while Gobo change 083 089 Color11 190 193 Sto 110 119 Enable blackout 099 112 Color7 075 082 Colort0 P while Gobo change 065 088 Colore 068 074 Color9 133 Rotation Slow 100 109 Disable blackout olor 071 084 Color5 060 067 Color8 Q while Color change 057 070 Color4 053 059 Color7 090 099 Enable blackout 043 056 Color3 045 052 Color6 128 Rotation hast while Color change 029 042 Color2 038 044 Color5 080 089 Disable blackout 015
6. 028 Color1 030 037 Color4 000 127 Index while Pan Tilt move 000 014 White 023 029 Color3 070 079 Enable blackout 015 022 Color2 0 0 while Pan Tilt move 008 014 Color1 fo 000 007 White 000 069 No Function 14A 11 channel modes 11Channel mode 128 Rotation Slow 113 127 Color8 099 112 Color7 085 098 Color6 071 084 Color5 057 070 Color4 043 056 Color3 029 042 Color2 015 028 Color1 000 014 White 105 112 Color14 098 104 Color13 090 097 Color12 083 089 Color11 075 082 Color10 068 074 Color9 060 067 Color8 053 059 Color7 045 052 Color6 038 044 Colors 030 037 Color4 023 029 Color3 015 022 Color2 008 014 Color1 000 007 White 189Rotation Slow Gr 128 Rotation Fast 110 127 Gobo7 shak 101 109 Gobo5 shaking 092 100 Gobo4 shaking 083 091 Gobo3 shak 074 082 Gobo2 shaking 064 073 Gobo1 shaking 048 063 Gobo6 040 047 Gobo5 032 039 Gobo4 024 031 Gobo3 016 023 Gobo2 008 015 Gobo1 000 007 White ing ing 194Rotation Slow 190 193 Stop 189 Rotation Slow O 128 Rotation Fast 000 127 Index Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 Ch7 4 Ei Pan Tilt Pan Pan Fine Tilt Tilt Fine Speed Dimmer Shutter 2557 540 255 2551 270 255 2557 Slow 255r 100 248 255 _ Open 240 247 Random 232 239 Open Fast Open 190 231 slow Close 182 189 Open 140 181 e 132 139 Open Fast 444 16 131 ss Le 8 15 open 0 0 0 0 0 0 OL Fast 0 0
7. ain Hold and press the MENU button for about one second or wait for one minute to exit the menu mode wits Channel Mode Press the MENU button to show Lid on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the B Ch 8 channel mode or ii th 11 channel mode mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode DLAI Show Mode Lr Press the MENU button to show 25 1c on the display Press the ENTER button and the I CL 7 display will blink Use the DOWN and UP buttons to select the Sh i show 1 or arm show 2 or Sh 3 show 3 or 5h H show 4 mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode A r Split Color Mode LI Press the MENU button to show SPU on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the 25 Split color mode or me normal mode Once the mode has been selected press the ENTER button to setup to g
8. ange press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode ZANACO QU Sound Mode Press the MENU button to show 95 on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the COTE mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode sie Pan Inversion Press the MENU button to show on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the aa normal or pan inversion mode Once the mode has been selected press the ENTER button to setup H H i to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode 8A Lye iL Tilt Inversion Press the MENU button to show on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the OO normal or tilt inversion mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one sec
9. cation and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements Innovation Quality Performance 19A
10. e display will show the number of working hours of the unit To go back to the functions press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode Q Press the MENU button to show Vue on the display Press the ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode 10A IOC OC Defaults Setting Press the MENU button to show on the display Press the ENTER button and the display will blink Use the DOWN and UP button to select the MES or oo Once the NES has been selected press the ENTER button and use the UP and Down button to a oC select the Frac or Hurt a He cad For Ae users detailed explanation as followings Es Laid gt Li Lh PLE gt H2S Ed gt Sit gt bund gt BES D in gt LoFF 6068 gt SE LPPa gt no e ieke gt Fo e Pd gt LoFF Es Fuae gt 13 OD La nuta Mostly automatic mode for non professional users detailed explanation as followings
11. e 1349 354 154 81 52 Orange 11300 2832 1215 659 391 Light green 8176 2081 917 490 297 re a E T ES EE om FR RER EE QO T o L eT A Distance m 0 1 0 2 0 3 0 4 0 5 0 Spot diameter m 0 23 0 46 0 7 0 93 1 21 3 How To Set The Unit 0000 e 4A Display To show the various menus and the selected functions LED DMX On DMX input present MASTER On Master Mode SLAVE On Slave Mode SOUND Flashing Sound activation Button MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions Only for remote control Connecting with CA 8 CA 9 CA 9RTX to control the unit for Stand by Function and Mode function Mains input Connect to power supply DMX input output For DMX512 link use 3 5 pin XLR cable to link the unit together 3 2 Main Function To select any of the given functions press the MENU button up to when the required one is showing on the display Select the function by pressing the ENTER button and the display will blink Use the DOWN and UP buttons to change the mode Once the required mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode The main functions are showing below
12. ee ways 1 Master slave built in preprogram function 2 Easy controller 3 Universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will take effect at once Every time you turn the unit on it will show 1550 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 12A 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave the first unit will control the other units to give an automatic sound activated or synchronized light show This function is good when you want an instant show You have to set the first unit into master mode Did and select Eh i show 1 or Gh g show 2 or 5h Jl show 3 or SHS show 4 mode Its DMX input socket will have nothing plugged into it and Its master LED will be constantly on and sound 1 and select LED will flash to the music The other units will have to set in slave mode normal or 2 light show mode Their DMX cables plugged into the DMX input sockets daisy chain and the slave led lights will constantly on 2 light show cll slave mode means the unit works normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you ha
13. k the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Make sure the unit does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 17A 6 Fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 18A EC Declaration of Conformity We declare that our products lighting equipments comply with the following specifi
14. o back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode CI M tiig Slave Mode Press the MENU button to show Bundi on the display Press the ENTER button and the 7A display will blink Use the DOWN and UP buttons to select the normal or 2 light show mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode ffe t AL LUH Blackout Mode m H Press the MENU button to show D d on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the 25 yes blackout or me no blackout mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode LI Sound Mode Press the MENU button to show on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select het on sound on or Orr sound off mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any ch
15. on to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode 9A IT ULL Dimmer Calibrate Press the MENU button to show CL AL on the display Press the ENTER button and the display will blink Use the DOWN and UP button to calibrate the dimmer for a maximum output from SI limited to 50 of the really max output to UL maximum output is not limited Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode LOC LGE JET Self Test Press the MENU button to show PSE on the display Press the ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode Lome LEIT Temperature Test Press the MENU button to show on the display Press the ENTER button and the display will show the temperature of the unit To go back to the functions press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode Fixture Hours Press the MENU button to show Ehr D on the display Press the ENTER button and th
16. ond or wait for one minute to exit the menu mode t Co Lee Led Display Press the MENU button to show l display will blink Use the DOWN and UP buttons to select the op Led on or La Led off mode Once the mode has been selected press the ENTER button to setup to go Ion the display Press the ENTER button and the FE back to the functions without any change press the MENU button again Hold and press the MENU button for about one second or wait for one minute to exit the menu mode CO Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button to show on the display Press the ENTER button to change to the mode display normal It will automatically store after 8 seconds Or press the ENTER button again return to the mode display inversion To go back to the functions press the MENU button Hold and press the MENU button for about one second or wait for one minute to exit the menu mode Display normal mode for the fixture putting on the floor Display inversion mode for the fixture fixing under ceiling C IO CLD Function Delay Press the MENU button to show Fua on the display Press the ENTER button and the display will blink Use the DOWN and UP button to select the 0 No Delay or 1 2 3 Wait for 1 2 3 seconds before these Functions of 15 16 CH are activated deactivated mode Once the mode has been selected press the ENTER butt
17. put of the next unit The cable can not be branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 1 512 usually 0 amp 1 are equal to 1 The end of the DMX 512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 16A 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 Pin 5 Not used 5 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems chec
18. s use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 2 Technical Specification e iMove 50S is the combination of the latest high powered LED technology excellent optics and great features e DMX control 8 11 channels selectable e 3 operation modes DMX Master Slave Sound Activation e Great built in lighting programs under master slave mode triggered by music e Optional CA 8 easy controller or CA 9 RTX wireless easy control kit for instant lighting shows e Rotating gobo wheel with 6 gobos plus white e Color wheel with 8 colors plus white Beam angle 15 e Automatic Pan Tilt position correction e Smooth 0 100 dimming and variable strobe speeds e LED display for easy navigation and addressing e Perfect for disco club bar parties and Mobile Dus e Pan 540 Tilt 270 3A Voltage 120V 230V 50 60Hz Power consumption 112W at 230V Light source 1 x 50W LED Dimensions 299 x 247 x 420 mm Ogobo wheel 109 mm Mgobo 19 mm Weight 10 kgs Photometric diagram White 36000 7835 3596 1949 1172 Yellow 24600 6044 2687 1420 262 Cambridge blue 6670 1739 770 409 253 Dark green 7760 1976 872 473 286 Red 1572 397 176 97 59 lux Purplish red 1312 328 143 79 47 Blu
19. t where the temperature is higher than this e Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing or servicing e In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts e Do not touch any wire during operation as high voltage might be causing electric shock Warning e To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture e Do not open the unit within five minutes after switching off 2A e The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Caution There are no user serviceable parts inside this unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also alway
20. ve two units only CT Lut In 3 4 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units functions press the MENU button again Stand By Blackout the unit g Function 1 Sync Strobe Show 1 Press to select color 2 Async strobe 1 4 2 Hold to select gobo e A 3 Sound Strobe Mode Sound LED OFF Show LED LED ON LO Slow Blinking Baie 4 3 DMX Controller By using a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the Mode is showing on the display Pressing the ENTER button and the display will blink Use the DOWN and UP buttons to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 units 13A 8 Channel Mode q 1G di 11 Channel Mode l ic di 44 4 4 DMX 512 Configuration 8 channel modes 8Channel
Download Pdf Manuals
Related Search