1649-mobilehawkquickstartguide
Contents
1. 32 bit color uncheck Show this dialog at startup recommended 2 Select the default imager name Mobile Hawk 1 or type a name of your choice in the Description text field and click OK 3 Click Y hen this dialog appears Important The imager must be in USB or RS 232 Mode to connect ce Sie ae h to ESP Read the symbol below that corresponds with your communication h interface ma r AR o M418 02 M188_02 aa oe P Reset to RS 232 Test Symbol Save f r USB RS 232 2 J Would you like to connect to the Mobile Hawk Factory Defaults Settings Mode Mode ics Step 5 Select Protocol Select the communications protocol you are using and click Next USB The reade must be in the proper mode to USB Connect Mode Click the Show Connect Symbol button Corrmet_ Cornel Back Net gt C Cancel 1 You will see the USB Connect Mode symbol Print and decode this symbol if you have not already done so in Step 3 to ensure that you are in the correct communications mode Keep the printed symbol in a convenient place for future use Click Next when you are finished 2 You will then see your imager s ID in the Select Device field Click Connect RS 232 The reader rust be in the proper mode to Click the Show Connect Symbol indo Correa _Comect_ _Corce_ button Cea Cha Cea Print and decode the RS 232 Connect Mode symbol if you have not already done so in Step 3 and decode it wit2. 3 110022 Rev A Step 2 Set Up Hardware RS 232 Step 3 Install ESP Step 4 Select Model Hardware for RS 232 ESP Software can be found on the Microscan Tools CD that is packaged When you start ESP the following menu will appear 1 Mobile Hawk Handheld DPM Imager FIS 6170 0001G with the Mobile Hawk RS 232 Interface Kit USA 98 000074 04 1 Follow the prompts to install ESP from the CD 3 RS 232 Interface Kit Europe _ 98 000074 05 2 Click on the ESP icon to run the program RS 232 Interface Kit UK 98 000074 06 Installation Steps for RS 232 5 1 Power off the host m 232 cable to th 2 e A Note ESP can also be installed from the Download Center at 3 Connect the RS 232 cable to www microscan com GUS MINI MINI Hawk 0X Hawk the power supply cable P Ses ipl E al ang Minimum System Requirements l D y e 5 Open a terminal program e 166 MHz Pentium processor Pentium II processor recommended HyperTerminal for example e Windows Vista XP or 2000 operating system ae 7 and set 57 6K baud rate 8 e Internet Explorer 5 0or higher Skip EZ Mode data bits none parity and 2 stop bits lt 64 MB mini RAM 128 MB RAM ded 6 Read the Reset to RS 232 Factory Defaults symbol ee recommended 1 Click the Mobile Hawk button and then click OK If you do below 80 MB hard drive space not want to make this selection every time you start ESP 7 Read the Save Settings symbol below e 800 x 600 minimum 256 color display 1024 x 768
3. 734 01 M735 01 M107_01 M109 01 M108 01 Vibrate On Vibrate On Vibrate Off Beep On Beep Off Beep On Default an i i Save Settings M188 02 llilumination Quick Setup The following programming symbols allow you to set up and control illumination settings Q044 01 Q045_01 Illumination Default Dot Peen Enhance Mode Illumination Mode Large Mark Q046 01 Q047 01 Dot Peen Enhance Illumination Mode Medium Mark Dot Peen Enhance Illumination Mode Medium Mark an i Save Settings olan M188 02
4. Quick Start Guide Step 1 Check Required Hardware Step 2 Set Up Hardware USB M O b j e H a wk Mobile Hawk USB Hardware Note The USB interface draws its power from the host 1 One Mobile Hawk Handheld DPM Imager Hardware for USB H an d h el d D P M ma g er 2 One 12 ft USB cable pre installed 1 Mobile Hawk Handheld DPM Imager FIS 6170 0001G Mobile Hawk RS 232 Hardware 2 fer Sarr Included The RS 232 cable is affixed to the handle with two screws a spacer Installation Steps for USB and a cable clip which can be removed 1 Connect the USB cable 2 to 1 One Mobile Hawk Handheld DPM Imager the host You do not need to 2 Cable clip attachment power off your host computer 3 Spacer 2 Open any program in your 4 Tuo hreadedocrews host computer that can receive 5 RS 232 Interface Kit Optional Accessory e Eiaa sunnian 8 ft coiled RS 232 cable 3 Read the Reset to USB Factory ET Defaults symbol below e Power supply U S Euro or UK Note If you want symbol data USB Hardware Refer to the Mobile Hawk Handheld DPM Imager User s Manual for to be entered as keyboard text read the USB Keyboard Mode symbol below information about changing or adding cables ii 4 Read the Save Settings symbol below Fie r M049 03 M134 02 M188 _02 Reset to USB USB Keyboard Test Symbol Save Factory Mode Settings Defaults Mi ICROSCAN P N 8
5. default imager settings is designed to read the broadest range of mark types Switching to Dot Peen Enhanced mode enables additional image processing to read challenging marks 5 Use the Start Stop button to enable disable capture of images Moving the mouse over the image will display settings used to capture the image A green box will indicate the decoded symbol location 6 Click the Save Image button to save the image Save Image For Help press F1 Mobile Hawk 1 Mobile Hawk CONNECTED From here you can click on App Mode to access tree controls and graphic user interfaces with more comprehensive configuration options Step 8 Practice Decoding The Mobile Hawk features simple blue targeting LEDs to indicate optimal read range 1 Hold the imager about 6 from the mark and align the blue targeting pattern as shown here 2 Move the front of the imager steadily downward toward the mark and parallel to the mark surface 3 The imager will decode the mark at the optimal read distance typically from the point of contact to 50 contact 12 70 mm f Test Symbol Copyright 2009 Microscan Systems Inc Frequently Used Settings The following programming symbols allow you to control USB Keyboard Mode Targeting settings and Beep and Vibration settings ee USB Keyboard Mode M134 02 r Targeting LED On Targeting Default LED Off M
6. h the imager to ensure that you are in the correct communications mode Keep the printed symbol in a convenient place for future use Click Next and then Connect Step 6 Connect to ESP USB Once you have clicked Connect in the USB imager ID dialog Step 5 the CONNECTED message will appear in a green box in the status bar at the bottom right of the screen Conen Use HID You are now ready to configure the USB Mobile Hawk using ESP RS 232 Once you have selected RS 232 settings and COM port and clicked Connect the CONNECTED message will appear in a green box in the status bar at the bottom right of the screen ORMECTER I Point to Point COMI You are now ready to configure the RS 232 Mobile Hawk using ESP Step 7 Configure the Imager ESP s EZ Mode is the first view that appears once you are connected This view features simple instructions as well as tools for decoding symbol data and taking image captures ESP ESP Untitled File Model Options Connect Help B App Mode Connect Switch Model Welcome to Easy Setup Progra m Illumination Quick Setup v Default Dot Peen Enhanced Instructions For using the Mobile Hawk Small Medium Large 1 Align targeting on the symbol v Upload Images 2 Use the trigger button to initiate a decode sequence 3 Practice reading ideally the Mobile Hawk will read best with the face of the imager parallel to the target and within contact to 2 inches 4 The
Download Pdf Manuals
Related Search
1649 mobilehawkquickstartguide