Home

User Manual - Atomic Motion Systems

1. PC Controlled e Connect the first motion system in the chain to your PC using the supplied USB cable as described previously e Connect one end of the RJ 45 cable to the DMX Out port 7 DMX ports on the first motion system in the chain to the DMX In port on the second motion system e For each subsequent system you wish to control simultaneously connect another RJ 45 cable from the DMX Out port of the previous unit to the DMX In port of the next DMX Desk Controlled e Connect the DMX In port 7 DMX ports of the first motion system in the chain to your DMX control desk using the XLR gt RJ 45 DMX cable e Chain subsequent units together by following the second and third steps outlined in the PC Controlled section above Dip Switch Settings e The DMX512 address of the unit is set using switches 1 9 on the ADDR TERM switch panel 4 DMX address As with most DMX compatible equipment the addresses are set using a binary system by summating the values of all enabled on switches 1 9 to give the address e g switch 1 enabled on and 2 9 disabled off Channel 1 switches 2 and 4 enabled and all others disabled Channel 10 and so on Units set with the same address in the chain will operate in unison e IMPORTANT Switch 10 should only be enabled on in the LAST unit in the DMX chain this enables the termination resistor and if left disabled off unexpected results may occur If it is enabled on a unit prior to
2. 20hz 255 highest 100hz 9 0 255 Command Used to issue one shot commands to the unit Must be set to 0 at all other times Commands are as follows 255 Reset system It is recommended the command channel is set to the desired value for a minimum of 0 5 seconds before being reverted back to zero to ensure the command is transmitted correctly AT LINTE VADRI NASIASTIENAE A mi OS oe AVA GN SIMUL ATORS Appendix C Troubleshooting Possible Cause s Possible Solution s No motion one or e Power disconnected more actuators move freely Actuator overload safety mechanism defeated No motion Safety interlock activated LED actuators locked on switch panel and Atomic logo in place will be illuminated red e Incorrect software settings e Incorrect DMX channel setting Poor motion e Incorrect software settings output e Incorrect COG configuration No or poor Tactile Audio cables not correctly Transducer connected feedback TTi units only PC sound output low or muted e Check power is connected and AC power light is illuminated If power is connected disconnect power and USB then reconnect e Press the black ON button marked 1 e Disengage the safety interlock by pressing the black ON button marked 1 e If the red LED Atomic logo remains illuminated check the base plastic cover is free from obstruction and not pressing down on any o
3. properly e Ensure the COG is configured correctly for the control set and user to maximise performance If many users are to be using the system e g in commercial situations configure the COG for an average height person for optimum results e Use of a harness does not only provide added safety but when tightly secured can significantly enhance the motion sensation This is particularly applicable to highly dynamic applications such as racing or rallying where road surface detail typically produces smaller movements some of which may not be perceived due to the natural shock absorption of the upper body with respect to the seat The Atomic can provide exceptionally fast motion response and use of the harness maximises this benefit e Experiment extensively with your software settings to fine tune your ride in particular force level and pitch roll movement range As with any other system incorrect settings may yield disappointing motion results but a correctly tuned system can produce an incredible experience Sometimes less is more excessive force settings can result in overshoot producing a jittery feeling in flight type applications and excessive pitch roll movement range settings can reduce the response of the system to more subtle feedback such as road surface detail e If you have a TTi unit ensure your line level input connected to the Audio IN port on the Atomic has a strong signal and the volume output on your co
4. the last in the chain the subsequent units may not function correctly e Ifyou are unsure about DMX channel setup or will only be using a single motion system via PC control just set the unit to channel 1 by enabling switch 1 on and disabling all others off A RE MO TION SIMULATORS AT LINTE MOTION SYS TEMS DMX Channel Assignments The Atomic A3 can be controlled using a conventional DMX control desk The channel assignments are as follows NB remember to offset the channel number by your chosen base channel 0 255 Pitch Coarse Coarse pitch position 0 fully backward 255 fully forward 2 0 255 Pitch Fine Fine pitch position Used in conjunction with Pitch Coarse to form a 16 bit number allowing 65536 possible positions Pitch Coarse is the high order byte 3 0 255 Roll Coarse Coarse roll position 0 fully left 255 fully right 4 0 255 Roll Fine Fine roll position Used in conjunction with Roll Coarse to form a 16 bit number allowing 65536 possible positions Roll Coarse is the high order byte 5 0 255 Force Movement force 0 lowest 255 highest 6 0 255 Max Speed Movement maximum speed 0 lowest 255 highest If unsure set this to be permanently 255 7 0 255 TT Gain TTi Sets the gain volume of the tactile transducers 0 Units only lowest 255 highest 8 0 255 TT LFC TTi Sets the LFC Low Frequency Cut off of the tactile Units only transducers 0 lowest
5. the wheel yoke mount assembly towards or away from the seat as required ensuring that it is always seated within the clamps shown in the picture above and secure in place by tightening the adjustment knob clockwise Height Adjustment Loosen the adjustment knob shown on the right by turning anti clockwise Slide the wheel yoke mount top assembly higher or lower as required and secure in place by tightening the adjustment knob clockwise ATIC MOTION SYSTEMS Tilt Adjustment Remove the thumb screws shown on the left and located on the left and right of the wheel yoke mount adjust tilt to desired position and replace thumb screws SOON ATOIN1C VAN MOTION SYSTEMS y Shifter Throttle Switch Panel Mount Installation amp Height Reach Adjustment Remove the thumb screws shown in the picture on the right Adjust the height and reach relative to the wheel yoke mount assembly using the indexing holes provided and replace tighten the thumb screws gt Side Mount Installation amp Height Reach Adjustment Remove the thumb screws shown in the picture on the left Adjust the height and reach relative to the motion base using the indexing holes provided and replace tighten the thumb screws NB The side mount can be located on either the left or right of the motion base ANS RLY SERS ANTTIMIC Fas VADRIGNASIASTIENAE Centre of Gravity COG Setup In or
6. LENT LINII MO TION SYS TEMS Assembly amp Instruction Manual ELL MOLA ANTIINMIC VAN Mopoi AAMS Disclaimer The A3 motion simulator the system is capable of moving the user very rapidly and sharply and is therefore potentially dangerous for use by those with conditions including but not limited to spinal neck injuries weaknesses epilepsy motion sickness vibration injuries susceptibility and any other condition which makes the user adversely affected by sudden movements amp vibration If someone is in any doubt over their fitness to safely use the system then they should not do so If undecided seeking medical advice may help someone to decide upon their fitness to use the system The use of the system by children is entirely at the discretion of a responsible adult and we recommend that one be present at all times if children are using the system The system is also capable of causing injury damage to adults children animals and objects located too close to the system while in use It is therefore imperative that a clear area is kept around the system while in use Special care should be taken to ensure that children and animals are not able to enter this area In any event all users of the system and those who approve use of the system by children do so at their own risk All those in close proximity to the system whilst in use including the user bear responsibility for ensuring that they children ani
7. R audio jack cable optional Connect one end of the 3 5mm male gt 3 5mm lead to the Speaker Headphone Out port on your PC please refer to your PC s instruction manual if you require more information and the other to the Audio IN port 10 Audio Input Connect your headphones active only port is not sufficient for passive headphones or PC speakers to the Audio OUT port 11 Audio Input Alternatively if using a hi fi amplifier connect the 3 5mm gt 2 x Phono cable between the Audio OUT port 11 Audio Output and any available line input on your amplifier WARNING Output levels of audio devices can vary and the amplifier supplied has a large adjustment range to ensure lower level signals can be amplified to a useful level although too low a signal will still produce a weak tactile transducer response As a result it is possible to over amplify a strong input signal Over amplification will cause damage to the TTi system and will be noticeable by audible knocks and clicks from the transducers If you hear these turn the gain down until they disappear to avoid damage ELL MOLA ANTIINMIC VAN Mopoi AAMS Operation Power e Once power is connected to the unit ensure the AC power switch is on 1 Mains switch The AC switch will illuminate e Ensuring the motion base is clear of any hazards press the small black button depicted in the switch panel picture below Safety Interlock System The Atom
8. Seat Inclination Angle Adjustment To adjust the seat inclination reclination tilt loosen the inclination levers shown on the right by turning anticlockwise Adjust the seat to the desired inclination then retighten the levers by turning clockwise If further tightening is required press and hold the red button on the lever disengaging it from the tightening mechanism turn anti clockwise release the button and further tighten clockwise Pe A FULL MOTION ATOMIC AN VADRIENASIASTRIIENAE Foot Rest Pedal Mount Installation Attach the pedal mount plate to its mounting post using the supplied thumb screws as shown on the right two on each side To adjust the angle of the mount see Tilt Adjustment below e Insert the pedal mount into the base at the points shown in the picture on the right Ensure the bars pass through both of the clamps indicated and secure as shown below Reach Adjustment e Attach your pedal set to the foot rest via the mounting holes provided These are compatible with the following controllers but may be usable for others Logitech G27 G27 pedal set Saitek Pro Flight Rudder Pedals PZ35 NB If your pedal set is incompatible with the foot rest mounting holes straps can be used instead however AMS strongly recommend additional holes are drilled to provide additional stability where possible Reach Adjustment Loosen the adjustment knob shown on the left by turni
9. der to maximise the performance of your system it is important the COG is configured correctly based on the controllers you wish to use some pedal sets are significantly heavier than others for example Prior to configuring the COG ensure you have fully assembled the unit attached your controllers and adjusted everything for comfort by following the previous instructions in this manual NOTE Significantly incorrect COG settings can be detrimental to performance and reduce actuator life 1 Ensure the power is ON see the Operation section and the actuators homed to their centre positions With your back against the back of the seat in normal seated position press and hold the red emergency stop button for 4 seconds until power is disconnected from the actuators If the upper motion platform does not fall to the front or rear side to side movement is ok the COG is balanced proceed to step 4 If the COG is not balanced proceed to step 2 2 Ifthe motion platform falls to either the front or the rear loosen the reach adjustment levers of the steering wheel and pedal mounts Slide the seat forwards or backwards along its mounting rails in the opposite direction to which the platform was falling moving the wheel and pedal mounts by the same amount as the seat to maintain the driving position 3 Re power the actuators by pressing the black button see the Operation section and once homed repeat the above process from step 1 until the cor
10. f the 4 safety switches Ensure USB cable is correctly connected and system is present in Windows Device Manager refer to Windows manual Check software settings to ensure system is enabled and force or pitch roll movement range settings are not 0 refer to software user manual Check game has been recognised in software and motion preview is showing movement e Check DMX channel is set correctly and corresponds with that in software refer to software user manual Increase pitch roll movement range and or force setting in software refer to software user manual e Correctly configure the COG Ensure audio cables are properly connected PC sound output is set to full and audio cable is connected to correct port on soundcard Check TT Gain software settings refer to software user manual
11. ic logo should light up blue and the unit home to its centre position ready for operation f this does not happen please read the Safety Interlock System instructions below You can also refer to Appendix C Troubleshooting Safety Interlock System e The unit has a number of safety features including a trap detection mechanism and emergency stop button The trap detection mechanism consists of 4 switches one at each corner of the base where the housing is attached in the event a trapped foreign body is detected while motion is active this will push the housing down and activate one or more of these switches stopping the motion and locking the actuators in their place to prevent further movement The emergency stop button is the big red button shown on the right and when pressed will also stop the actuators preventing further movement e When either the trap detection mechanism or emergency stop button is activated the system will go into safety interlock and this condition will be highlighted by the red LED next to the emergency stop button the Atomic logo will also turn red NOTE pressing the emergency stop button quickly will lock the actuators in their place pressing and holding for longer than 4 seconds will disconnect power to the actuators and amplifier in a TTi equipped unit completely to allow safe removal of any trapped object e To exit the safety interlock mode and resume normal operation pre
12. ich is a software utility available freely from AMS for your Windows compatible PC To update your device s firmware 1 Ensure power is connected to the system and the system is connected to your PC via the supplied USB cable 2 Ensure the AMS DFU is correctly installed on your PC this also installs the required drivers to update your firmware 3 Put the Atomic in DFU mode Using a pair of pointed implements e g Ballpoint pen press and hold the F function button on the Atomic s I O panel 4 Keeping the F function button held down press and release the R reset button on the Atomic s I O panel 5 Finally release the F function button The device is now in DFU mode 6 Follow the on screen instructions provided with the AMS DFU to perform the firmware update and once complete disconnect and reconnect both the power and USB leads to the Atomic ANSIA ATIIMIC VAN VADRIENASIASTRIIENAE Appendix B DMX Network Setup Optional If you have a multiple units or devices you wish to link together to operate in unison this is achieved via the DMX networking capability Devices can be controlled using either your PC or a DMX compatible control desk see the DMX Channel Assignments below Additional cables required unsupplied 1 or more standard RJ 45 PC network cables e Optional control desk only 1 x 3 or 5 pin XLR depending on DMX control desk gt RJ 45 DMX cable
13. lt 8 Output Linear O Logarithmic Vert Force Pitch Multiplier a 1 6 ea n E No open Users Sound Feedback Tactile Transducers 7 Gan i 4 Freq Cutoff i 100 He e The Atomic can be controlled using either a PC via SIMPHYINTY software or similar or DMX capable controller refer to Appendix B DMX Network Setup e Instructions for downloading SIMPHYNITY will be provided separately by AMS along with your license information e When downloaded run the executable Windows Installer file which will guide you through the setup process Enter your license information required for installation and operation and follow the on screen instructions Restart your PC following installation to ensure drivers are correctly registered on your system e Ensure the motion base is connected to your PC via USB as SIMPHYNITY will not run if there are no AMS devices detected e When your PC boots SIMPHYNITY will start automatically If you have disabled this feature refer to the SIMPHYNITY instruction manual for details you will need to start it manually via the program shortcut in your Start menu e Assuming SIMPHYNITY is running its icon will appear in the system tray click on this to open the SIMPHYNITY application window e SIMPHYNITY s online help system accessible via the Help menu will guide you through the remainder of the setup process namely creating a user profile and assigning a channel to your device to allo
14. mals and possessions are not placed in danger by being too close to the system whilst in use The system is heavy over 50Kg and no attempt should be made by one person to lift the unit alone When attempting to move the unit or parts thereof safe lifting practices should be employed Anyone attempting to move or assist in moving the system or parts thereof do so at their own risk Any involvement by children in such movement is at the risk of a responsible adult Neither Next Step Solutions Ltd nor their partners affiliates shall accept any responsibility for injuries or damage to any person animal or object howsoever caused in interaction with the system ELL MOLA ANTIINMIC VAN VADRI NASIASTIENAE Congratulations on your purchase of the Atomic A3 Motion Simulator from AMS This guide will talk you through setting the system up for first use safety precautions and recommendations for maximising the life of your system For software instructions please refer to the software user guides available via their respective help systems IMPORTANT Please read this manual in full before attempting to assemble or use the Atomic A3 Failure to do so may result in damage poor performance reduced system life or injury Unpacking Checklist HOTAS Fighter System Racing Flight System Tools Required e 17mm spanner adjustable spanner Small flat head screw driver 3 5mm wide tip ideal lt 4mm TTi units only Addi
15. mputer is set to maximum for the best results e If possible secure your controllers firmly to their mounts using the mounting holes provided e To enhance the feeling of forward acceleration it is more advisable to tilt the seat inclination reclination further backwards using the mechanism described in section 1 rather than offsetting the centre position of the unit in your software This allows the system to still be able to respond to the greatest range of pitch motion possible for both acceleration and braking If you are unsure it is recommended you set the seat inclination reclination to about halfway for most applications e If you are using force feedback controllers use a high force setting the Atomic gives a substantial amount of force feedback so if your usual controller force settings are low they may get a little lost in the experience e For additional immersion and a better perceived motion experience it is highly recommended either headphones or a loud audio system is used e For increased immersion still use a large 3D ready screen projector multi screen surround or Virtual Reality HMD setup If possible remember to switch off the lights PLL MOLON ANTIIMIC VAN MOTION SYSTEMS Appendix A Device Firmware Update DFU From time to time it may be necessary to update the firmware of your Atomic system as AMS introduce additional functionality This is done via the AMS DFU Device Firmware Updater wh
16. ng anti clockwise Slide the foot rest towards or away from the seat as required ensuring that it is always seated within the clamps shown above and secure in place by tightening the adjustment knob clockwise Tilt Adjustment Remove the thumb screws shown in the picture on the right and located on the left and right of the foot rest pedal mount adjust tilt to desired position and replace thumb screws A POARTEN SIMUL AT ORS Steering Wheel Yoke Mount Installation e Attach the wheel yoke mount top assembly to its bottom assembly as shown on the right and secure in place using the clamp shown below Height Adjustment section Note The steering wheel yoke mount mechanism is reversible to facilitate both left and right hand drive layouts please contact AMS for further instruction if required e Insert the wheel yoke mount into the base at the points shown in the picture on the right Ensure the bars pass through both of the clamps indicated and secure as shown below Reach Adjustment e Attach your steering wheel or flight yoke to the steering wheel table via the clamp bar and if additional stability is required also the holes provided These are compatible with the following controllers but may be usable for others e Logitech G27 G27 steering wheel Saitek Pro Flight Yoke PZ44 Reach Adjustment Loosen the adjustment knob shown on the left by turning anti clockwise Slide
17. rect balance is achieved 4 When satisfied the COG is configured correctly fully tighten the seat mounting nuts shown in the picture above along with the wheel and pedal mount reach adjustment levers Note In situations where many users will be riding e g commercial settings it is recommended the COG is configured for an average height user within the group to obtain the best results A POE NAP ran SIMUL AT ORS ATIC MOTION SYSTEMS Wiring Rear IO Panel 1 Mains power switch illuminated when on 7 DMX networking IO ports 2 Fuse holder 8 R Reset button 3 IEC mains power input 100 240VAC 50 60Hz 9 USB input 4 Motion base DMX address 10 Audio input TTi units only 5 F Function button 11 Audio output TTi units only 6 Indicator LEDS top controller status bottom power Basic Setup Connect the supplied USB lead to the USB port 9 USB Input and the other end to any available USB 1 1 or above port on your computer Connect the supplied IEC Mains lead to the Power port 3 IEC Input and the other end to any available mains socket The acceptable input voltage range is universally compatible with all standard mains power supply systems 100 240VAC 50 60Hz Amplifier Wiring TTi Units Only If you have a TTi enabled unit the following additional unsupplied cables are required 1 x 3 5mm male gt 3 5mm male jack cable 1 x 3 5mm male gt 2 x Phono L
18. ss the black ON button shown on the right Indicator LEDs e When USB power but not mains power is connected the power LED on the rear IO panel will be illuminated RED When mains power but not USB power is connected the power LED on the rear IO panel will be illuminated GREEN When both power sources are connected required for use the power LED will be illuminated YELLOW and the unit is ON e While in the ON state pressing the black button will place the unit into the IDLING awaiting data state it will home to its centre position and the status LED on the rear IO panel will blink slowly The Atomic logo will be lit up blue e When the unit is ACTIVE receiving motion data the status LED will blink rapidly e When the unit is in SAFETY INTERLOCK MODE the red LED next to the emergency stop button will be illuminated and the Atomic logo lit up red ELL MOLA ANTIINMIC VAN MOTION SYSTEMS Driver Software Installation Current Settings Default teed Seve tood Seve Aan Qutput 7 Motion Enabled TT Enabled MaxForce 4 0 G A z a Max Speed E uearn 150 0 oh settings import Export Restore pefauits tte Location Broweee N a W SIMPHYNITT Remote Injected Telemetry Reader Enabled Movement Behavior Ge GD commer f m n V Force Effect 33 F Reverse Bode ame vl Title DIRT 2 Version Not Aveadable Current Settings Defau
19. tional Recommended Tools e 13mm spanner e 6mm allen key 5mm allen key e Cable Ties or Velcro Straps for securing controller cables System Components Most system components are factory pre assembled Depending on configuration these consist of Atomic A3 Base Unit Seat amp Seat Fasteners Foot Rest Pedal Mount supplied in 2 parts Steering Wheel Flight Yoke Mount Racing Flight System Only supplied in 2 parts Shifter Throttle Switch Panel Mount Racing Flight System Only amp Fasteners Flight Stick Throttle Side Mount X 2 HOTAS System Only USB Cable IEC Power Cable A POE NAP ran SIMO mAN n BES AT LIN TC METEN SSS wa Motion Base Seat Installation e Remove the Atomic A3 base unit from its packaging and situate it on a level stable operating surface for intended use WARNING Never lift the base unit by the plastic housing or damage may result to the mounts the housing is floating for safety reasons Always lift from the front and rear of the metal top table e Locate the four mounting posts highlighted in the picture above 1 Each one has a nut attached with two washers which must be located above and below the seat mount respectively e 2 shows how each mounting post appears then the system is first unpacked Remove the nut and top washer from all four mounting posts leaving the lower washer in place on each 3 OPTIONAL The posts can be shifted laterally to support var
20. w SIMPHYNTIY to correctly identify it t is strongly recommended you read this help file in full in order to get the most from your system ELL MOLA ANTIIMIC VAN VADRI NASIASTIENAE Safety Precautions e Ensure power to the unit is switched off when not in use e While not essential it is recommended a harness is worn at all times for added safety e Ensure spectators are kept at arms length when the unit is in operation and there are no obstructions in or around the base or foot rest e Ensure loose clothing is not in the proximity of any moving parts to reduce the risk of trapping or injury e For maximum stability the base should be mounted on a flat level surface with the front support legs extended and all support feet making good contact with the ground when a user is seated The rear castors should be just above or barely touching the ground e As with any other highly dynamic system it is good practice to check all adjustment levers fasteners are tight and secure before each use The Atomic is a highly durable system however it is necessary to provide some user releasable mechanisms to facilitate rapid comfort adjustment It may be preferable in heavy use situations e g commercial scenarios to replace hand adjustable levers and fasteners will tooled alternatives e Ensure users keep their feet on the foot rest pedal mount at all times while the unit is active to prevent trapping or injury e Adjust the s
21. ying seat widths if you are fitting your own seat To do this the mounting post can be loosened by inserting an allen key into the top of each post and turning anti clockwise Slide the posts to the position you require and re tighten the posts by turning the allen key clockwise e Line up each of the seat rail slots with the mounting posts ensuring each rail is correctly seated on the bottom washer 4 e Place the top washer onto each mounting post and screw down each of the four nuts on top of it 5 Do not fully tighten the nuts yet tighten just enough so the seat can still slide forward and backwards along the rails This is because the Centre of Gravity COG with need configuring once the system is fully assembled e Optional TTi equipped systems only Connect the tactile transducers attached to the bottom of the seat to the motion base using the connectors shown on the right ensuring red is connected to red and black to black on each side ELL MOLA ANTIINMIC VAN MOTION SYSTEMS Support Legs Site the motion base on a level surface and extend the support legs highlighted in the picture on the left Ensure the plastic feet are making contact with the ground e For further stability holes are provided on the bottom of the base unit to allow it to be secured to a platform if desired Note this requires the removal of support legs and castors please contact AMS for further information and advice
22. ystem for comfort prior to operation ensuring the user s limbs can move freely and easily e It is strongly recommended the safety interlock mechanism is activated via the emergency stop button when entering or exiting the seat to reduce the risk of injury in case unexpected motion Occurs e When in use it is strongly recommended pitch roll movement range settings do not allow the actuators to hit their end stops indicated by a knocking sound when the pitch or roll reaches the end of its travel Under normal use there is a protection mechanism to prevent this however if abnormal loads are applied there is a slim possibility this can be defeated potentially damaging the actuators due to excessive shock If you feel this is happening reduce your pitch roll movement range settings e Take care when entering and exiting the seat sudden impacts can result in excessive load shock to the actuators The actuators feature an overload protection mechanism which quickly disconnects power to the relevant actuator in these circumstances should this happen you will need to reset the unit by disconnecting and reconnecting both power and the USB cable NISATEIN SSS VMAS K ATOMIC VEE Hints amp Tips e Adjust your system fully to find the perfect driving position before starting The Atomic provides extensive adjustment to simulate many different types of vehicle layout which can greatly enhance the feel of the system when configured

User Manual - Atomic Motion Systems

Contents

Download Pdf Manuals

Related Search

Related Contents