LED Spot W User Manual - Tangent Industries Inc.
Contents
1. e read the safety chapter and the warning notices in these Operating Instructions and to observe them at all times during operation e in particular to observe the safety measures in of DIN EN 62471 2008 Photobiological safety of lamps and lamp systems and observe BG 5006 Dangers from Handling the Unit The LED Spot W is assembled according to the technological state of the art and recog nised safety standards The following potential dangers can occur Danger from electrical current Danger from heat eyes skin Danger from UV radiation actinic UV close UV Danger from blue light 300 700 nm The unit must be used only under the following circumstances e When wearing personal safety equipment to protect the eyes and skin in case complete shielding of the UV radiation cannot be ensured Goggles should conform the stan dard EN 170 max spectral trans mission 365 nm 0 3 and should afford protection from radiation both directly and from the side e The LED Spot W must be set up and operated in such a way that persons are not subjected to direct or indirect radiation UV absorbent plastics or metal sheet can be used as shields e Warning notices must be affixed at the workplace and at all entrances to the work area e Under no circumstances must the LED Spot W be operated in explo Danger sion protected areas or in the prox imity of flammable materials gases or liquids The2. 47301e1 LED Spot W Organisational Measures Informal Safety Meas ures Checking the Water Lines Danger from Electrical Power Danger from UV Irradiation 4 Safety Regulations Organisational Measures The functions of all the existing safety equipment must be inspected regularly before the start of work or of each new shift Look for outwardly visible damage Informal Safety Measures The general and local regulations on accident prevention and environmental protection must be provided and observed as a supplement to the Operating Instructions Checking the Water Lines Water lines connections and couplings of the water cooling must be regularly checked for leak tightness Danger from Electrical Power The electrical equipment on the LED Spot W must be inspected regularly Inspection before starting work e Check all components of the unit for out e wardly visible damage Loose connections must be repaired im mediately and damaged cables must be replaced e Check that all electric cables are in flaw p less condition Danger There is danger of direct or indirect contact with electricity Danger from UV Irradiation The LED Spot W emits radiation in the range of 340 440 nm depending on the type The optical output power is detailed in the Technical Data chapter When working with the unit the following instructions must also be followed e Personal safety equipment must be worn to prote
3. Dangers from Handling the WAM cx cc ce ticcravessnesctnanartbaanescenshexeestanndncotnensbansnatenndusaeecusasaeanhanedabansants 8 dare alala g Sits ttt re crv ces el lea cy cn tein E anime E TE E E E 9 4 ATELY FROQUIAL ONS naana a a a a TE 10 Organisational MCASUISS cdncisoniinaierirrianeiuisinvininsunsidabiln E NE EE 10 informal Safety Measures cps csiiineusoreiisancacaweinmunnnaesicicmstncntinucirish adn cciiantonebeetendnawasinchpesioniaremedniadbas 10 Checking the Water INS Saks ncactcaviuatrdemneenabaoncinibdetinpareineninsdins pena seimdenduimecudaninpethsund vue isonetaateleet 10 Danger from Electrical POWE ciasiniciiinpeanviandieninindexninutiur dieeniheadenmel ainawistliar binwedoidwnduct lived eeii iaa 10 Danger from UV Imadiati n sascicctives cousesswceniirunettbessecnisunieronadidutnbuaiwecnaedet peenixeiunees venierabieeiinestodeds 10 Danger om Heal aactetieutetonadnateasapaone RER n AREA REER ER EEA A AR EKIRAR 11 wanani and Br 91 i aerate ey Trt E a rey ort reer 12 Maintenance and Fault REMOVAL cccccccssscecsessscessesseeceeesseecseeeeesseusecessenseeeseueeessenseeensansess 12 5 Transport Storage Delivery ccccccsseeeesseeeeeeseeeeeeeeeseeeeeeaeeeeeeesaeeeeeanaeeeeeaneeeeeanseeseneneeseoans 13 6 Installation Commissioning and Operation ccccccceceesseeeeeeeseeeeeeseeeeeeeseeeeeneseesseneeeesseneeees 14 General INONMA O eseon an e E OEE O ri 14 EV GTEC ell Connec ONS renee E E E E S meinen 15 EE E
4. LED Spot W must be operated only by persons who have been in structed in all the safety precautions The LED Spot W must be used only when it is in flawless condition in terms of safety Operation is not permitted when there is visible damage to the housing water hoses supply cables or the mains adapter Proper functionality of the entire cool ing unit must always be ensured All relevant regulations on accident prevention and on the handling of units belonging to Risk Group 3 must be ob served COE Improper use can endanger the health of the user or of third parties severe skin or eye damage 47301e1 Intended Use The LED Spot W is a high intensity UV irradiation device for irradiating large ar eas from a close distance Any other or additional usage is regarded as improper use and is thus dangerous The LED Spot W must not be used for medi cal or therapeutic purposes for skin tanning or in other medical equipment A nle v technology Intended Use The unit must be used indoors only Outdoor use is not permitted The operator must operate the unit only in accordance with the usage notes in these Operating Instructions Danger There is acute danger of becoming blind if you look directly into the radiation outlet aperture If improperly handled UV radiation can damage skin and eyes It can lead to severe sunburn or to inflammation of the retina and conjunc tiva and possibly to skin cancer 9
5. contamination and if necessary re placed entirely e When connecting or disconnecting it is imperative to ensure that no water gets onto the LED Spot W or into the connector plug Warning N Condensation may lead to destruction of the device It is absolutely essential to avoid any formation of condensed WARNING water on the surface of the LED Spot W The proprietor has therefore to provide adequate climatic conditions at site air humidity temperature The temperature of the cooling water may be adjusted if necessary 47301e1 21 LED Spot W Dimensional drawing of the LED Spot W angled version 22 Warning The cooling parameters must be adhered to without fail otherwise damage could occur to the LED Spot W Dimensional drawing of the LED Spot W angled version water connection plug cable connection M3 4 depth on both sides 2 a E hy Z a a z A i 2 approx 200 00 47301e1 A nle v technology Dimensional drawing of the LED Spot W straight version 47301e1 20 00 14 50 Dimensional drawing of the LED Spot W Straight version ajay water connection plug cable connection approx 200 00 M3 4 depth on both sides 23 LED Spot W Dimensional Drawing of the Filter Unit Dimensional drawing of the filter unit G1 4 2x 24 47301e1 A nle v technology Optical Data Optical Data Typical
6. for damage to and contamination of the outlet aperture If necessary the outlet aperture must be cleaned see the chapter Cleaning e Inspection of the filter unit e Inspection of the leak tightness of the water connections As needed at regular intervals dependent on operating conditions e Replacement of the filter unit see the chapter Filter Change Cleaning Note When cleaning do not use any aggressive or abrasive cleansing agents If operated in a dusty environment or in the presence of fumes from adhesives the radiation emission surface of the LED Spot W can become contaminated This diminishes the UV in tensity e Clean the radiation aperture surface with a clean lint free cloth and alcohol 47301e1 A nle v technology Filter Change MEN T Filter Change 1 Switch off the bluepoint LED HP main switch in position 0 2 Switch off the cooling unit and detach it from the mains supply 3 Counterrotate both of the red shutoff valves 1 of the filter unit by 90 to the direction of flow position OFF 4 Unscrew the reservoir container 2 from the filter unit and remove it When doing this watch out for remaining water that might leak out of the reservoir container and collect in an appropriate vessel if necessary 5 Remove the attachment screw 3 and filter 4 1 Shutoff valve 2 Reservoir container with O ring 3 Attachment screw 4 Filter 6 Put the new filter in plac
7. may be adjusted if necessary 47301e1 15 LED Spot W Warning The cooling parameters must be adhered to without fail otherwise WARNING damage could occur to the LED Spot W Connecting the LED Spot W via the Adapter Connecting the The LED Spot W is connected by means of the adapter 45979 LED Spot W via l l l the Adapter Before connecting the LED Spot W ensure that the bluepoint LED HP has been switched off main switch 1 in position 0 1 Insert in the adapter 3 into the LED channels 2 2 Tighten the securing nuts 4 for the adapter 3 Insert the LED Spot W plug connector 5 and tighten it In the next step the water cooling will be installed 16 47301e1 A nle v technology Connecting the Water Cooling to the LED Spot W In the following a typical connection schematic is shown for a water cooling circuit with three connected LED Spot W Water cooling unit bluepoint max 3x LED Spot W 1 Connect the inflow line of the cooling unit to the filter unit 2 Hook up the connector of the filter unit with the LED Spot W max distance 1 m 3 Hook up the return line of the cooling unit with the second connector on the LED Spot W The device is now ready for operation and can be switched on via the main switch 1 Warning N Condensation may lead to destruction of the device It is absolutely essential to avoid any formation of condensed WARNING water on the surfac
8. 385 395 405 5 nm are available This way the LED Spot W can be adapted to the respective application The square light emitting aperture encompasses an area of 20 mm x 20 mm and can depending on the required intensity homogeneity substantially increase its ef fective area by changing the distance to the substrate The resultant irradiation field can then be divided into four segments which can be activated independently of each other External water cooling enables the extremely compact format while offering the highest radiation intensity e Intelligent output control e Operating hours counter for the LED integrated in the LED unit e Independent setting of the irradia tion time irradiation intensity and operating mode for each channel e No warm up period e No standby period Uses The LED Spot W can be used for the following applications in laboratories in production and for making repairs e Bonding and securing of components in just seconds in the electronics optical and medical sectors e Bonding of glass metals and plastics e High intensity UV irradiation in the chemical biological and pharmaceutical industries e Fluorescence excitation for materials testing and image processing e Used to dry inks and colour coatings e g in inkjet printers 47301e1 A honle v technology Features Uses LED Spot W Connections and Operating Elements Connections ah eae The following f
9. Dr Honle AG may be used If any third party parts are used then the operational safety of the LED Spot W cannot be ensured 47301e1 A nle f tennan 9 Technical Data General Data Typical LED service life gt 10 000 hours Wavelengths in nm 365 375 385 395 405 Tolerance 5 nm Type intensity in mW cm 1200 1500 3900 4200 Supply 90 V 264 V 47 Hz 63 Hz General Data Connected load max 200 W Dimensions of LED Spot W approx 60 x 50 x 17 mm without connections H x W x D Weight approx 350 g without water Depending on the operating conditions and cooling conditions Measured using a H nle LED measurement head for UV meters Water Cooling Operating Conditions It is imperative to comply with the following connection information operating conditions for Water Cooling the LED Spot W and the filter unit Filter unit connections Ya BSP inside thread LED Spot W connections coupler socket NW 5 BA self closing Max pressure 3 5 bar e Min flow rate 2 I min Max inflow water temperature 25 C Min inflow water temperature 16 C Coolant demineralised water e Max distance filter unit LED Spot W 1m e Make sure that no condensation may form on the surface of the spotlight e The filter unit for the coolant must always be in flawless condition It must be checked daily and if necessary replaced without delay e The coolant must be regularly inspected for
10. ct the eyes and skin unless the UV radiation is completely screened by structural measures The LED Spot W must be set up in such a way that persons are not sub jected to direct or indirect radiation e Inthe case of workplaces where man ual work is performed or in mobile ap plications the working area must be enclosed in an appropriate manner e Never look directly or indirectly into the LED aperture 47301e1 A nle v technology Danger There is acute danger of becoming blind if you look directly into the radiation outlet aperture If improperly handled UV radiation can damage skin and eyes It can lead to skin burns or to inflammation of the retina and conjunc tiva and possibly to skin cancer Warning UV radiation can cause material damage to electronic components When used in the vicinity of the LED Spot W these components must be protected from UV radiation Warning UV radiation accelerates the ageing of materials UV sensitive objects and surfaces must therefore be protected from radiation Note Protective articles are listed in the chapter Ordering Data for Units Replacement Parts and Accessories 3 gt I gt D Danger from Heat ag gritorn When operating the LED Spot W take the following thermal risks into account The LED Spot W can heat up to a tem or explosive materials gases or liquids perature of 55 C during operation There is an acute risk of fire or explo There is a ri
11. e aE ea a EEE E A T TA E A A E EE 15 7 Service Maintenance and Cleaning ccccccesseeeeeeeseeeeeeeeeeeeeeeseeeeeeeseeeseeeseeeseneseesseneeeessonenees 18 General Informati ssxceuresscanncassiack snssrercnassnecharsac dens cannsnaurtneoeaansebunbacstnusncineasahenademeimaquanmeseabatts 18 not AV gt eee mn teeta A Ce nee ene E ec ee ree eer ere 18 VS AV VEE dems ari eany esteslg Shoe aesciottne daar cas E E T E ae edn 18 TEREE E TE conn aean EE A EI AAA A S E 19 8 Ordering Data for Units Replacement Parts and Accessories ceceeeeeeeeeeeeeeeeeeeeeeeees 20 KoE EEE EP E T EA A E T A E O E E E T E T TA 20 EEDE POEN e E E eae ere ee eee 20 Replacement Parts Accessories cccccseccccseecccneeceeuececaueecsueeessuseesaeeesauseesuecessusesseeessaeseees 20 9 tecc DA A eresia i AE E 21 arnor O A eee a a a E a savin 21 Water Cooling Operating CONGMONS iii ccesssecssvesiicnevincascetsoncesivessesencstareessicceseaeacebuxssatcsuerstcenessanees 21 Dimensional drawing of the LED Spot W angled Version cccccccseeeceeeeeeeeeeeeeeeeeeaeeeeeeeaaees 22 Dimensional drawing of the LED Spot W straight Version cccceeeeceeeeeeeeeeeeeeeeeeeeeeesaeees 23 Dimensional Drawing of the Filter Unit cc ceccceceeeeeeeeeeeeeeeeeeeeeeseeeeeeeseaeeeeeseeeeeseeeeeeeesaaees 24 Pue VEE eea NE mere te et cu aa reat rae arate ar ete ee ere er ere eae 25 47301e1 3 LED Spot W 1 Introduction These Ope
12. e and fasten it securely with the attachment screw 7 Screw the reservoir container onto the filter unit again 8 Rotate both of the shutoff valves of the filter unit into the OPEN position again 9 Reconnect the cooling unit to the mains supply again and switch it on 10 After first switching on the system again check the filter unit for leak tightness 47301e1 19 LED Spot W Ordering LED Spot W Replacement Parts Acces sories 20 8 Ordering Data for Units Replacement Parts and Accesso ries Ordering Order replacement parts from our replacement parts service at the following address Dr Honle AG UV Technologie Lochhamer Schlag 1 D 82166 Grafelfing Tel 49 0 89 856 Fax 49 0 89 856 LED Spot W Designation LED Spot W 365 nm LED Spot W 375 nm LED Spot W 385 nm LED Spot W 395 nm LED Spot W 405 nm Replacement Parts Munich Germany 08 0 08 148 I Accessories bluepoint LED HP com ponent 45250 Adapter for bluepoint LED 4 1 45979 UV warning sign 45890 Operating Instructions German English on CD ooling unit ilter unit nsert for filter unit Water connection set straight fittings Water connection set angled fittings Connection cable 1 5 m Connection cable 2 5 m Connection cable 4 0 m Connection cable 1 5 m 90 Connection cable 2 5 m 90 Connection cable 4 0 m 90 Connector for hose DN5 BA D 6 Warning Only original replacement parts from
13. e of the LED Spot W The proprietor has therefore to provide adequate climatic conditions at site air humidity temperature The temperature of the cooling water may be adjusted if necessary Warning All connections must be checked for leak tightness immediately after being switched on for the first time and then regularly thereafter If there are any leaks the system must be switched off immediately It may only be switched on again after all flaws have been corrected and the released water has dried up completely 47301e1 17 LED Spot W General Infor mation Service Cleaning 7 Service Maintenance and Cleaning General Information Service repair and cleaning work may only be performed by authorised personnel e When performing service maintenance and cleaning it must be ensured that the outlet aperture of the LED Spot W does not become dirtied by fingerprints or other contami nants e Likewise no sprayed water may contact the surface of the LED Spot W e In general work should be performed with a clean cloth or clean gloves e Only touch the LED Spot W on the metal housing e If necessary clean the outlet aperture of the LED Spot W when it is cold using a clean cloth and alcohol Note Contamination of the outlet aperture due to fingerprints or the like re duce the UV output of the LED Spot W Service The following service work is performed on the LED Spot W Daily e Inspection of the LED Spot W
14. ghonle Operating Instructions LED Spot W 47301e1 LED Spot W Masthead All rights reserved Copyright by Dr Honle AG Lochhamer Schlag 1 82166 Grafelfing Munich Germany Printed in Germany July 2011 These Operating Instructions must not be reprinted or otherwise duplicated even in part without the express written consent of Dr Honle AG Any kind of duplication dissemination or storing on any form of data medium that is not authorised by Dr Honle AG constitutes an infringement of prevailing copyright law and will be prosecuted Technical alterations that serve to improve the unit described or improve the standard of safety are expressly reserved even without further notice Publisher responsible for the content Dr Honle AG Layout Dr Honle AG 47301e1 A nle v technology Table of Contents 1 Taligets ves Ce 9 sarae E a e 4 2 DESCNP IOMa a A 5 FeO a E E E hpmcboratuathaninensinbovandus 5 MS E E T A oe T E E E E E A A O OE N eneeres 5 Connections and Operating EleMent cccccccccccsssececceeseeessesececseesececseaseeesseaseeeseeaeeesseaseesseees 6 3 oie 121 4a See eee ne ee cen en ene ae one Re Ome eee eee ae ees mee ne ee ee eee me aero Seer ey 7 CSCS INOS P EA TE A A nen cokeensabc 7 BELE ai o Jenene etre E AA AR E RE eee ae oe eee 7 Obligation of Personnel ieisscaicusicencssinmneriairtddensasobntunt ataaedeinarssbantavennepadeimnuntastiatauenippbeisnieaieeataient 8
15. he LED Spot W You must ensure that adequate con trol measurements are maintained in order to eliminate or minimise these risks You can use the information contained in these Oper ating Instructions when making the risk as sessment Improper use can endanger the health of the user or of third parties severe skin or eye damage The H nle LED Spot W is subject to the standard DIN EN 62471 2008 Photobiological safety of lamps and lamp systems It is classified as belonging to Risk Group 3 which re quires special safety measures to be observed when operating it These are described in detail in the stated DIN EN standard Due to the size of the LED Spot W it is not possible to directly label the unit The proprietor must therefore ensure that appropriate identification of the danger area is made in immedi ate vicinity of the LED Spot W DURCH STREUSTRAHLUNG VERMEIDEN BEDIENUNGSANLEITUNG BEACHTEN RISIKOGRUPPE 3 nach EN62471 2008 IN VISIBLE LED RADIATION AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION TAKE NOTE OF INSTRUCTION MANUAL RISK GROUP 3 according to EN62471 2008 47301e1 A honle v technology General Notes Risk Group LED Spot W Obligation of Personnel Dangers from Handling the Unit Obligation of Personnel Persons who are entrusted to work with the LED Spot W are obliged before starting work to e observe the regulations on work safety and accident prevention
16. he chapter Service Maintenance and Cleaning Carrying these out ensures reliable operation Should a fault occur in the unit that cannot be rectified with the help of the Operating In structions then Dr Honle AG Customer Ser vice must be contacted Parts that are not in flawless condition must be exchanged immediately Use only original replacement and wear parts There is no guarantee that other manufac turers parts are designed and manufactured Warning Warning i gt ID be used e Contamination of the quartz glass pane of the LED Spot W e Contamination of the water cooling element as a result of using unsuit able or contaminated coolant e Failure of the cooling unit and or op eration of it that is non compliant with the specified operating conditions see Technical Data e Disastrous occurrences e Acts of God to meet the required standards of robustness and safety No alterations additions or modifications must be made to the LED Spot W without the permission of Dr Honle AG Contact address for claims under warranty repair and replacement part service Dr Honle AG UV Technologie Lochhamer Schlag 1 D 82166 Grafelfing Munich Germany Tel 49 0 89 856 08 0 Fax 49 0 89 856 08 148 E mail uv hoenle com Website www hoenle de No repairs or alterations must be made to the unit except those de scribed in these Operating Instructions Only original Dr Honle AG replaceme
17. igures show the LED Spot W from both the front and rear view ements The water connections mounted on the back of the unit are available with either angled or straight fittings See chapter 6 1 hos fame et 1 LED Spot W rear view LED Spot W front view Threading from the side 4 Sub D plug 15 pin 4 x M 3 4 mm deep Light emitting aperture with protective glass Water connections Note The appropriate water connections straight angled are already mounted at the time of delivery 6 47301e1 3 Safety Notes General Notes Familiarity with all basic safety regulations is the prerequisite for safe handling and prob lem free use of the LED Spot W These Operating Instructions contain the most important notes for operating the unit in a safe manner The Operating Instructions especially the Safety Notes must be observed by everyone that works with the unit In addition all applicable rules and regula tions on accident prevention for the use area must also be observed DIN EN 62471 2008 Photobiological safety of lamps and lamp systems and BGI 5006 Oct 2006 are re ferred to here Risk Group f sDanger f The proprietor must check the safety conscious work performance of personnel at regular intervals In accordance with the workplace safety regulations the proprietor is advised to make a reasonable and sufficient assessment of the risks arising from the use of t
18. intensity distribution as a percentage 2 mm spacing Intensity ATTY TTR SO ga TH ttt Winx bod cra ing pe i ne ae ji X Typical intensity characteristics over operating distance in distance in mm Typical intensity characteristics over operating distance Intensity in Distance in mm 47301e1 25 LED Spot W Relative spectral irradiance Typical optical output dependent on the LED temperature at 100 set value For further information on the different operating modes please refer to the operating in structions of the bluepoint LED bluepoint LED HP chapter LED mode Typical optical output power dependent on the LED temperature at 100 set value Power mode om Peak Power mode ConstPower mode rel opt output power LED temperature in C Fig 1 LED Spot W 375 nm Typical optical output power dependent on the LED temperature at 100 set value Power mode Peak Power mode ConstPower mode rel opt output power O T Bane aa a een Ses a as aa i 35 40 LED temperature in C Fig 2 LED Spot W 405 nm 26 47301e1
19. nt parts and wear parts must 47301e1 A nle v technology 5 Transport Storage Delivery Scope of Delivery of the LED Spot W Scope of Deliv ery LED Spot W Operating Instructions possibly on a CD The delivered pars must be inspected for completeness and damage or other issues Any damage that has been ascertained must be documented at once and reported to the dealer or to Dr H nle AG without delay The following components are also necessary to operate the LED Spot W bluepoint LED HP component LED Spot W connection cable filter unit cooling unit water connections hoses couplings etc Note Please dispose of the packaging material in an environmentally re sponsible manner It may be possible to reuse it It is recommended to keep the packaging material in case the unit has to be sent by post or otherwise transported 47301e1 13 LED Spot W General Infor mation 6 Installation Commissioning and Operation General Information e Itis imperative to comply with the speci fied operating conditions for the water cooling see the chapter Water Connec tion e The LED Spot W must be mounted on a stable fixture e The ambient temperature for operating the LED Spot W must not exceed a maximum of 35 C e Without exception the LED Spot W must only be connected or disconnected with the bluepoint LED HP switched off If the LED Spot W is disconnected during on going o
20. perations this could cause dam age to the device and or a component Danger Do not touch the contact pins in the LED Spot W plug connector with your fingers danger of ESD damage Protect the LED Spot W against chemical vapours and cleaning agents Only operate the LED Spot W in dry rooms Rel humidity max 70 non condensing Open air operation is not permitted Before switching on check to ensure that all plug type connectors incl water con nections are properly seated and tight It should be observed that the LED Spot W is not exposed to any spray water Furthermore no condensation may form on the surface of the spotlight Sufficient cooling must be provided for when installing the LED Spot W It is forbidden to operate the device in the immediate vicinity of flammable objects liquids or gases The dimensions for the LED Spot W can be found in the dimensional drawings in the chap ter 9 Technical Data 47301e1 A nle v technology Electrical Connections The supply with electric current and activation of the LED Spot W is accomplished via the Electrical Con bluepoint LED HP For detailed information on the electrical connections refer to the blue nections point LED HP Operating Instructions in the chapter Electrical Connections Warning The LED Spot W must only be used with the bluepoint LED HP com ponent Warning Connecting and disconnecting of the LED Spot W must only be done when
21. rating Instructions describe the LED Spot W its operation and its uses The safety and danger notices explain the safe proper handling of the LED Spot W The following symbols and designations are used in the Operating Instructions Danger This symbol means immediate danger to life and limb for persons in the surroundings i gt Warning This symbol means possible danger to the machine or its surround ings iP Note This symbol indicates notes usage hints and useful information a 4 47301e1 2 Description The LED Spot W is a water cooled large area irradiation unit developed for all applica tions that require high intensity UV irradiation of large areas As a result of the high inten sity and the possibility for programming en tire program sequences such as illumina tion sequences with varying intensities and latencies for example completely auto matic production lines with minimal cycle times and or machine processing times can be realised in particular The typical LED service life is 10 000 hours The LEDs can be switched on and off as of ten as desired No warm up or cool down phases are necessary Features e Extremely high irradiance despite miniscule dimensions e Uniform irradiation of large surface areas e Long LED service life e Available in different wavelengths e Has four independent LED seg ments e Entry of complete program se quences VA Wavelengths of 365 375
22. sk of burns It must be en sion sured that the units cannot be touched To protect against the danger from heat The tightly bundled radiation of the LED the same measures must be taken that can lead to heating up of the radiated are effect against the Danger from UV Ir surfaces especially dark surfaces radiation see the chapter Danger from There is a risk of burns UV Irradiation Under no circumstances must the unit be operated in the vicinity of flammable Danger The LED Spot W emits highly intensive bundled radiation Improper use can endanger the health of the user or of third parties severe DANGER skin or eye damage 47301e1 11 LED Spot W Warranty and Liability Maintenance and Fault Re moval Warranty and Liability The Dr Honle AG General Conditions of Sale and Delivery always apply They are avail able to the user upon signing the contract at the latest Dr Honle AG assumes no liability whatsoever for damages that can be attributed to one or more of the following causes e Improper use of the LED Spot W contrary to its intended use e Incorrect assembly commissioning or operation of the LED Spot W e Failure to observe notes in the Oper ating Instructions e Unauthorised structural modification of the LED Spot W e Effects of foreign objects or me chanical damage caused by blows jolts etc Maintenance and Fault Removal All necessary maintenance tasks are de scribed in t
23. the bluepoint LED HP is in a switched off state Use the main switch on the back of the device for this purpose Otherwise damage could occur to the LED Spot W or the bluepoint LED HP iP i gt Water Connection It is imperative to comply with the following connection information operating conditions for Water Connec the LED Spot W and the filter unit tion Filter unit connections Ya BSP inside thread LED Spot W connections coupler socket NW 5 BA self closing Max pressure 3 5 bar Min flow rate 2 I min Max inflow water temperature 25 C Min inflow water temperature 16 C Coolant demineralised water e Max distance filter unit LED Spot W 1m e Make sure that no condensation may form on the surface of the spotlight e The filter unit for the coolant must always be in flawless condition It must be checked daily and if necessary replaced without delay e The coolant must be regularly inspected for contamination and if necessary re placed entirely e When connecting or disconnecting it is imperative to ensure that no water gets onto the LED Spot W or into the connector plug Warning Condensation may lead to destruction of the device It is absolutely essential to avoid any formation of condensed WARNING water on the surface of the LED Spot W The proprietor has therefore to provide adequate climatic conditions at site air humidity temperature The temperature of the cooling water
Download Pdf Manuals
Related Search