穨 66M-K800-002(A)
Contents
1. from the unit Caution Do not dispose of battery in fire Caution Do not attempt to open the battery peed The following precautions should be taken when replacing the attery v remove watches rings etc v use tools with insulated handles 8 Place your new battery in the same position direction and reconnect the wires red wire position and black wire negative 9 Please follow steps 5 4 and 3 in that order to reconnect the entire unit 10 Please follow manual instructions in order to properly reconnect your equipment 11 Storage 10 1 Storage conditions Store the UPS covered and upright in a cool dry location with its battery fully charged Before storing charger the UPS for at least 4 hours Remove any accessories in the accessory slot and disconnect any cables connected to the computer interface port to avoid unnecessary draining the battery 10 2 Extended storage During extended storage in environments where the ambient temperature is 15 to 30 C 5 to 86 F charge the UPS s battery every 6 months During extended storage in environments where the ambient temperature is 30 to 45 C 86 to 113 F charge the UPS s battery every 3 months 12 Troubleshooting PROBLEM POSSIBLE ACTION TO TAKE On test button not Press the on test button to power the UPS pushed or push too and the load short UPS input circuit Reduce the load on the UPS by unplugging UPS will not turn on break tripped equipm2. immediately or input fuse protection Hot swappable Sealed Maintenance free lead acid Typical 4 hours to 90 of full capacity Recharge Time Automatic self test amp discharge protection Replace battery indicator 10 30 minutes depending on computer load PHYSICAL Net Weight 13 8 14 5 15 15 8 25 30 kat EN CN i Kg Ibs 32 6 34 1 35 2 37 0 59 4 70 4 xDxH nput Inlet IEC 320 power inlet Receptacles NEMA 5 15R 115V IEC 320 female appliance coupler 230V Continue beeping sound Overload INTERFACE RS 232 Bi directional communication port CONFORMANCE Safety cUL TUV CE meet FCC Meet IEEE 587 standard Two years ENVIRONMENT 6 000 meters max elevation 0 95 humidity non condensing operation 0 40 deg C Audible noise lt 40dBA 1 meter from surface lt 45dBA 1 meter from surface Stora 15000 meters max elevation condition O S ALARM Battery Slow beeping sound about 0 25Hz Back Up Battery Low Rapid beeping sound about 1 00Hz verload rge age 14 Specifications A 800A RM 1250A RM 1500A RM 2000A RM 2500A RM 3000A RM INPUT 25 at line input Single phase 50 or 60Hz 5 auto sensing OUTPUT Voltage Pure sine wave output at 5 of nominal 10 after low battery on battery warning Frequency 50 or 60Hz 0 5 on battery Voltage AVR automatically increase output voltage 15 above input voltage if Regulation 9 to 25 of nominal AVR decrease outpu
3. the SNMP adapter make your UPS becomes SNMP manageable provide a real time UPS and power status information for the network manager Note It s not necessary to use this function Caution Use only factory supplied or authorized SNMP monitoring cable 3 14 OUTPUT POWER RECEPTACLES 3 15 AC INPUT POWER RECEPTACLE 3 16 INPUT CIRCUIT BREAKER It trips when the connected loads exceed the protected receptacle s capacity The center plungers of the circuit breakers extend when tripped 3 17 SITE WIRING FAULT INDICATORS RED LED It comes on when the UPS is connected to an improperly wired AC power outlet Note This device is available on 110 Vac model only 3 18 COMPUTER INTERFACE Provide both RS 232 and relay signal to support NOVELL UNIX DOS WINDOWS and other operating systems 4 Installation 4 0 Inspection Inspect the UPS upon receipt The packaging is recyclable save it for reuse or dispose of it properly 4 1 Placement Install the UPS in a protected area with adequate air flow and free of excessive dust Do not operate the UPS where the temperature and humidity is outside the specified limits 4 2 Connect Computer Interface optional RUPS series software or other power management software and an interface kits can be used with this UPS Use only kits supplied or approved by the manufacturer If used connect the interface cable to the 9 pin computer interface port on the back panel of the UPS Note Computer interf
4. Do not dispose of batteries in a fire the battery may explore v Do not open or mutilate the battery released electrolyte is harmful to the skin and eyes v A battery can present a risk of electric shock and high short circuit current The following precaution should be observed when working on batteries Remove watches rings or other metal objects Use tools with insulated handles Caution Risk of electric shock hazardous live parts inside this unit are energized from the battery supply even when the input AC power is connected Caution Risk of electric shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel Warning To reduce the risk of fire replace only with the same type and rating of fuse Warning To reduce the risk of fire or electric shock install in temperature and humidity controlled indoor area of conductive contaminants 3 Presentation FRONT PANEL 3 1 ON TEST button With the UPS plugged in press the ON TEST button to turn on the UPS and power the loads ON TEST also activates the UPS s self test and utility line voltage displays 3 2 OVERLOAD indicator RED LED The LED lights when the loads connected to the UPS exceed the UPS s capacity See Section 6 3 3 3 BACK UP indicator GREEN LED The LED illuminates when the UPS is supplying battery power to the loads 3 4 REPLACE BATTERY indicator RED LED The LED illuminates when the U
5. ON TEST button more than 1 second and UPS performs a self test function During the self test the UPS operates a back up mode Note During the self test the UPS briefly operates the loads on battery the on battery LED comes on If the UPS passes the self test it returns to on line operation The on battery LED does off and the on line LED goes on steady If the UPS fails the self test it immediately returns to on line operation and lights the replace battery LED The loads are not affected Recharge the battery overnight and perform the self test again If the replace battery LED is still on ask our nearest dealer to replace battery 5 4 Silence In BACK UP mode push ON TEST more than 1 second to silence the audible alarm The function is void when under condition of LOW BATTERY or OVERLOAD Note At back up mode UPS can be automatically turned off if none of the connected loads is operating 5 5 Load bar graph The 5 LED display See section 3 8 for location of the indicator on the front panel shows the power drawn from the UPS by load The display indicates the percentage of the UPS s rated capacity For example If three LEDs are lit the load is drawing between 50 and 67 of the UPS s capacity If the UPS is overloaded the overload LED lights and alarm sounds See section 6 3 5 6 Bttery charge bar graph The 5 LED display see section 3 9 for location of the indicator on the front panel shows the present charge o
6. PS s battery is no longer useful and must be replaced See section 9 Note When replace battery disconnect the utility power then open the case and take notice of the battery s polarity while install the new battery to avoid short See section 9 3 5 BUCK AVR VOLTAGE REDUCTION indicator YELLOW LED The LED illuminates when the UPS is correcting a high utility voltage condition The loads receive normal power 3 6 LINE NORMAL indicator GREEN LED The LED illuminates when the line input voltage is normal 3 7 BOOST AVR VOLTAGE BOOST indicator YELLOW LED The LED illuminates when the UPS is correcting a low utility voltage condition The loads receive normal power 3 8 LOAD bar graph The display shows the power being drawn by the load 3 9 POWER bar graph BATTERY CHARGE LINE VOLTAGE The display shows the present battery charge as a percentage of battery capacity It also display the voltage of utility line 3 10 OFF button Press the OFF button to turn off the UPS and the loads REAR PANEL 3 11 TEL MMODEM SURGE PROTECTION Surge protection for telephone and modem line to have the complete safety connection for INTERNET service 3 12 EXTERNAL BATTERY PACK CONNECTOR optional Caution Use only factory supplied or authorized connecting cable for external battery 3 13 SNMP INTERFACE PORT optional Provide the SNMP adapters for 10 BaseT Ethernet and Token Ring connectors Through RS232 communication port
7. UPS Uninterruptible Power System Line Interactive Network Protection Pure Sine Wave Output UPS Regular models600A 800A 1000A 1250A 1500A 2000A 2500A 3000A amp Extended Run Time Models 1000AL 2000AL 3000AL USER S MANUAL Printed in USA A instructions Thank you for selecting this uninterruptible power system UPS It provides you with better protection for connected equipment Please read this manual This manual provides safety installation and operating instructions that will help you derive the fullest performance and service life that the UPS has to offer Please save this manual It includes important instructions for the safe use of this UPS and for obtaining factory service should the proper operation of the UPS come into question Please save or recycle the packaging materials The UPS s shipping materials were designing with great care to provide protection from transportation related damage These materials are invaluable if you ever have to return the UPS for service Damage sustained during transit is not covered under the warranty Table of contents To Entro d U CLIO Nica a SP OY CNO Sask cepecete T T gem adem dees ie edeed ceed T sO y Prosentat Ms cee cere ta 6 Front Panel Rear Panel Output 45 Ins talla tiO Mco eter scene ect aceieee lath scree cieieteieie 12 5 Operaatio tec eee dio te tal 74 Bue CALLA AM Su is da ma ad 5 To Software OpillO nS liniers 0 8 Maintenance cmmmcmenenemnciin
8. ace connection is optional The UPS works properly without a computer interface connection Caution Use only factory supplied or authorized UPS monitoring cable 4 3 Connect external battery pack optional Before connecting make sure the external battery pack and the connector cable are compatible with this UPS Note External battery connection is not necessary The UPS works properly without a external battery pack connection Caution Use only factory supplied or external battery connection cable 4 4 Connect the telephone modem lines Connect a single line telephone or a modem line into the telephone modem surge protection sockets on the back of the UPS The RJ 45 RJ 11 modular sockets accept standard single line telephone connections This connection will require another length of telephone cable supplied Note This connection is optional It is not necessary to use this UPS Caution The telephone line current limiting feature could be rendered inoperable ifimproperly installed Make sure that the telephone line from the wall is plugged into the connector marked IN and the device to be protected telephone modem etc is plugged into the connector marked Caution This surge protection device is for indoor use only and never install telephone wiring during a lightning storm 4 5 Connect to Utility Connect the AC input power connector to utility power to power up the UPS 4 6 Charge the battery The UPS charges its ba
9. cecceemeemeenememememememememeneed 9 Computer Interface POrFtoocnncnoncnnnnncncnnn o o ee meeeeemeeeeees 17 10 Battery replaceMenNteinncdiincncncmcncnencmameneniaana manana nal 8 A ICONO ii 18 12 Troubleshooting ekee a R RA NES 19 13 Battery Pack Installati0N o oocmcconcnconenencnconananonnana mars 20 14 Specification Si inicio ii 21 66M K800 011 66M K800 012 1 INTRODUCTION The product is line interactive UPS with the newest technology and powerful function The LINE INTERACTIVE UPS is with AVR function allows input voltage range from 75 to 125 including on line voltage boost up amp buck down An ideal protection equipment for critical connected loads It is based on microprocessor controls with utility power connected the charging is ongoing no need to switch ON the UPS and at back up mode UPS can be automatically turned OFF if none of the connected loads is operating to save the battery energy The indicator will be ON when battery needs replacement and a cyclic self testing function is Wet esh in order to verify both the operation of the UPS and the condition of the attery In addition This UPS provides advanced single telephone line or modem surge suppression through the modular connectors on the back panel The LINE INTERACTIVE UPS and RUPS seies monitoring software optional kits makes your computer operate intelligent and provides you with the ability of perfect protection of your critical devices Note T
10. e UPS emits continuous alarm to warn a overload condition Disconnect nonessential load equipment from UPS to eliminate the overload 6 4 REPLACE BATTERY continuous alarm The UPS emits continuous beeps and the REPLACE BATTERY LED illuminates if the battery fails the self test See section 9 to replace battery by yourself or call your dealer for services 7 Software options 7 1 Power Monitoring Software The RUPS series software or other power monitoring software is applied standard RS 232 interface to perform monitoring functions and then provides an orderly shutdown of a computer in the event of power failure Moreover RUPS displays all the diagnostic symptoms on monitor such as Voltage Frequency Battery level and so on The software is available for DOS Windows 3 1x Windows 95 Windows NT V3 5 or later Novell Netware and others Call your dealer for more information on computer OS compatible solutions 7 2 Interface Kits A series of interface kits is available for operation systems that provide UPS monitoring Each interface kit includes the special interface cable required to convert status signals from the UPS into signals which individual operating system recognize The interface cable at UPS side must be connected to REMOTE PORT at computer side can be either COM 1 or COM 2 The other installation instructions and powerful features please refer to READ ME file Caution Use only factory supplied or authorized UPS mo
11. ent and reset the circuit breaker by pressing the plunger back in Very low or no utility Check the AC power supply to the UPS with voltage multimeter Computer interface Disconnect the computer interface or UPS will not turn on or of accessory accessory If the UPS now works normally off problem check the interface cable the attached Push on test or off computer and the accessory no UPS operates on UPS s input circuit Reduce the load on the UPS by unplugging battery even though breaker tripped equipment and reset the circuit breaker normal line voltage is UPS beeps occasionally Normal UPS operation Normal condition UPS does not provide The UPS s battery is Charge the battery Remove nonessential equipments Front panel indicators The UPS has been shut None The UPS will restart automatically flash down by remote control when utility power returns sequentially All indicators are flash Internal UPS fault Do not attempt to use the UPS Turn the And the UPS emits a UPS off and have it service immediately Constant tone The UPS operates Building wire error such Have a qualified electrician correct the building normally as missing ground or hot wiring but the site wiring fault to neutral wire reversal indicator is lit The UPS is shut down None The UPS will return to normal operation Low battery light is on and the battery is when the power is restored and the battery has and all LED is off discharged and a suffici
12. ent charge exhausted Weak batteries The batteries to recharge for at least four hours The replace battery light If the problem still exists after recharging is lit replace with batteries 13 Battery Pack Installation Install up to 8 battery packs per xxxA L model UPS following the instruction below 1 2 3 BLACK 1 Prepare the UPS to connect the battery pack s 2 Note the hotes used to attach the battery pack connector clamp 3 Insert the battery pack connector into the UPS To install additional batte RED procedure using the battery pack connectors on the battery packs Note Do not stack battery packs 14 Specifications ooo BOA sooA 1000A 1250A 1500A 2000A INPUT OUTPUT Voltage Pure sine wave output at nominal 5 on battery Frequency 50 or 60Hz 0 5 on battery Voltage AVR automatically increase output voltage 15 above input Regulation voltage if 9 to 25 of nominal AVR decrease output voltage AVR 15 below input voltage if 9 to 25 of nominal PROTECTION Spike Protection 320 Joules 2ms AND Unit Input Fuse for overload amp short circuit protection FILTERING EMI RFI filter 10dB at 0 15MHz 50dB at 30MHz Overload UPS automatic shutdown if overload exceeds 110 of nominal at Protection 20 second and 125 at 2 seconds 2 4 milliseconds including detection time Short Circuit UPS output cut off
13. f the UPS s battery as a percentage of the battery capacity When all five LEDs light the battery is fully charged When only two LED lights the battery can supply less than two minutes of run time for the load 5 7 Cold start When the UPS is off and there is no utility power use the cold start feature to apply power to the loads from UPS s battery Press the ON TEST button see section 3 1 for location of the indicator on the front panel until the UPS beeps 5 8 Shutdown mode In shutdown mode the UPS stops supplying power to the load waiting for return of utility power If there is no utility power present external devices e g servers connected to the computer interface can command the UPS to shutdown This is normally done to preserve battery capacity after the graceful shutdown of protected servers The UPS will scroll the front panel indicators sequentially in shutdown mode 6 1 BACK UP slow alarm When in BACK UP mode the YELLOW LED illuminates and the UPS sounds an audible alarm The alarm stops when the UPS returns to LINE NORMAL operation Press the ON TEST button during on battery alarms to stop the beeping 6 2 LOW BATTERY rapid alarm In BACK UP mode when the battery energy runs low the UPS beeps rapidly until the UPS shuts down from battery exhaustion or returns to LINE NORMAL operation 6 3 OVERLOAD continuous alarm When the UPS is overloaded the connected loads exceed the maximum rated capacity th
14. here is no guarantee that interference to radio TV will not occur ina particular installation If this UPS causes interference to radio or television reception which can be determined by turning the UPS off and on the user is encouraged to try to correct the interference by one or more of following measures O connect the equipment to an outlet on a circuit different from that to which the receiver is connected increase the separation between the equipment and the receiver reorient the receiving antenna 2 Safet CAUTION v To reduce the risk of electric shock disconnect the UPS from the mains supply before installing a computer interface signal cable Reconnect the power cord only after signaling interconnections have been made v The internal energy source the battery cannot be de energized by the user The output may be energized when the unit is not connected to a mains supply v The right way to de energize the UPS properly in an emergency is to move the I O switch to the OFF position and disconnect the power cord from the mains supply v The socket outlet shall be installed near the equipment and easily accessible v Attention hazardous through electric shock Also with disconnection of this unit the main hazardous voltage still may be accessible through supply from battery The battery supply should be therefore disconnected in the plus and a pole when maintenance of service work inside the UPS is considered v
15. ich must be pulled up to a common referenced supply no greater than 40 Vdc The transistors are capable of a maximum nonconductive load of 25 mAdc Use only pin 7 as the common 2 W Pin 5 generates a High to Low signal when the battery inside the UPS has less than 5 minutes back up time left 3 W Pin 2 generates a High to Low signal when the line is fail 4 M The UPS will shut down when a high RS 232 level is sustained on pin 6 for 0 36 seconds 5 M Pin 9 is also the RS 232 data output 6 M Pin 6 is RS 232 data input RxD NOTE 1 Switch rating 40V 0 15A non inductive 2 Pin 7 should be connected to ground only 10 Battery Replacement Your battery should run any where from 3 5 years before eve needing to be replaced Please follow the instructions below for easy battery replacement 1 Unplug unit from AC power source and disconnect all connected equipment 2 Disconnect AC power cord from unit 3 Turn unit upside down and using a phillips screw driver unscrew the 4 screws holding the top of the unit to the bottom Put screws in a safe place for reconnection 4 Holding the top together firmly with the bottom turn the entire unit right side up 5 Carefully lift top cover off and place to the side The connecting wires and electronics will be exposed Be careful not to touch any inner components when changing the battery 6 Remove the 2 connecting wires from the battery 7 You can now easily remove the battery
16. ndows 95 98 NT Novell Unix and other popular systems ENVIRONMENT Ambient 3 500 meters max elevation 0 95 humidity non condensing operation 0 40 deg C Audible noise lt 40dBA 1 meter from surface lt 45dBA 1 meter from surface Storage 15000 meters max elevation condition 14 Specifications MODEL IA oA 3000A TOOOAL 2000AL 3000AL INPUT Capacity 2500VA 3000VA TOOOVA 2000VA 3000VA Voltage Voltage 25 at line input Single phase 50 or 60Hz 5 auto sensing OUTPUT Voltage Pure sine wave at 5 of nominal 10 after low battery on battery warning 50 or 60Hz 0 5 on batter AVR automatically increase output voltage 15 above input voltage if 9 to 25 of nominal AVR decrease output voltage 15 below input voltage if 9 to 25 of nominal Surge 320 Joules 2ms Protection FILTERING z Unit Input Breaker for overload amp short circuit protection EMI RFI filter 10dB at 0 15MHz 50dB at 30MHz Overload UPS automatic shutdown if overload exceeds 110 of nominal at Protection 20 second and 125 at 2 seconds 2 4 milliseconds including detection time Short Circuit UPS output cut off immediately or input fuse protection Type Hot swappable Sealed Maintenance free lead acid with 3 6 ears life time Typical 4 hours to 90 of full capacity Recharge Time Built in Charge Current Supplied a eee External pack Depend on request Packs Automatic self test amp discharges protec
17. nitoring cable 1 Keep the unit clean and vacuum the ventilation intake periodically 2 Wipe with soft loose and damp cloth 3 Check for loose and bad connections monthly 4 Never leave the unit on an uneven surface 5 Position the unit to allow at least 10 cm clearance between the rear panel and the wall Keep the ventilation intake open 6 Avoid direct sunlight rain And high humidity 7 Stay away from fire and extremely hot location 8 Do not stack materials on top of the unit 9 The unit should not be exposed to corrosive air 10 The normal operating temperature is 0 40 C 9 Computer Interface Port The computer interface port has the following characteristics The communication port on the back of the UPS may be connected to host computer This port allows the computer to monitor the status of the UPS and control the operation of the UPS in some cased lts major functions normally include some or all of the following X to broadcast a warning when power fails X to close any open file before the battery reserves are exhausted X to turn of the UPS Some computers are equipped with a special connector to link with the communication port In addition special plug in card may be needed Some computers may need a special UPS monitoring software Contact your dealer for the details on the various interface Kits The computer interface port has the following characteristics 1 Pin 5 and 2 are open collector outputs wh
18. t voltage 15 below input AVR voltage if 9 to 25 of nominal PROTECTION Spike Protection 320 Joules 2ms AND Unit Input Fuse for overload amp short circuit protection FILTERING EMI RFI filter 10dB at 0 15MHz 50dB at 30MHz Overload UPS automatic shutdown if overload exceeds 110 of nominal at 20 Protection second and 125 at 2 seconds 2 4 milliseconds including detection time Short Circuit UPS output cut off immediately or input fuse breaker protection Hot swappable Sealed Maintenance free lead acid with 3 6 years lifetime Typ Typical 4 hours to 90 of full capacity Recharge Time Automatic self test amp discharge protection Replace battery indicator Back up Time 10 30 minutes depending on computer load PHYSICAL Net Weight 18 0 23 5 26 1 28 4 55 2 57 8 Kg Ibs 39 6 51 7 57 4 62 4 121 4 127 1 Shipping Weight 19 5 25 0 27 7 30 0 58 0 60 0 Kg Ibs 42 9 55 0 60 9 66 0 127 6 132 0 WxDxH 483 x 381 x 130 483 x 508 x 221 Input Inlet IEC 320 power inlet Receptacles NEMA 5 15R 115V IEC 320 female appliance coupler 230V ALARM Battery Slow beeping sound about 0 25Hz Battery Low Rapid beeping sound about 1 00Hz Overload Continue beeping sound INTERFACE Support both Provide power management amp diagnostic functions including power RS232 amp dry status battery low schedule UPS ON OFF battery load level display contact signal and more Compatible with Wi
19. tion Replace battery indicator Back up Time 10 30 minutes depending on computer load PHYSICAL Net Weight Kg 220V 30 110V 220V 10 220V 20 2 21 26 8 Shipping Weight Kay 3 se al a Nominal Battery 48V 48V 24V 48V Voltage z Dimension mm 170x445 110V 140x445 170x450 170x580 WxDxH x200 170x580x215 x200 x215 x215 Battery Slow beeping sound about 0 25Hz Back Up Battery Low Rapid beeping sound about 1 00Hz Continue beeping sound INTERFACE RS 232 Bi directional communication port nterface CONFORMANCE Safety cUL TUV CE FCC Meet IEEE 587 standard Two years including battery ENVIRONMENT Ambient 6 000 meters max elevation 0 95 humidity non condensing operation 0 deg C Audible noise lt 40dBA lt 50 dBA 1 meter from surface Storage 15000 meters max elevation condition
20. ttery whenever it is connected to utility power For best results charge the battery for 4 hours in the initial use 4 7 Connect the loads Plug the loads into the output connectors on the rear of the UPS To use the UPS as a master on off switch make sure all of the loads are switched on Caution Never connect a laser printer or plotter to the UPS with other computer equipment A laser printer or plotter periodically draws significantly more power than when idle and may overload the UPS 4 8 Check the Site Wiring Fault Indicator After plugging in the loads and the UPS check the site wiring fault indicator on the rear panel See section 3 17 for location of the indicator on the back panel It lights if the UPS is plugged into an improperly wired AC power outlet Wiring faults detected include ground hot neutral polarity reversal and overloaded neutral circuit CCC ee lil il o al i l 2058 4 5 1 Switch on With the UPS plugged in press ON TEST button less than 1 second to switch the UPS on The UPS will perform self testing each time when it is switched on Note When switched off the UPS maintains the battery charge and will respond to commands received through the computer interface port 5 2 Switch off By pressing and holding OFF button until the LINE NORMAL or BACK UP LED off 5 3 Self test Use the self test to verify both the operation of the UPS and the condition of the battery In normal utility power push the
Download Pdf Manuals
Related Search