FIBER OPTIC SPLICE CLOSURE
Contents
1. Opticube 16 Tying silica Gel and Trays Stack the trays using the connection parts on the side Place the provided silica gel on the splice tray lid and tie them together 17 Assembling the Closure Place the dome shaped cover onto the bottom portion Check the status of silicon gasket ring inserted in the slit of the dome shaped cover 18 Band clamp connection Fasten the dome shaped cover and the bottom portion together with a band clamp 19 Heating Heat Shrink tube Rub the inlet ports and the cable with the provided sandpaper and clean them with a cleaner to allow the sealing adhesives inside of the heat shrink tube to bond to each side 21 Aerial Installation VISSEM ELECTRONICS PAI 235 2 Deokpyeong ri Majang myeon Icheon city Gyeonggi do Korea 467 812 Tel 82 31 283 7852 Fax 82 31 283 7844 VISSEM OPT M0711 Printed in Korea VISSEM OFC 810A Emanual Rev 1 All rights reserved by VISSEM Electronics Co Ltd TEL 031 288 3484 FAX 031 283 78442. 10 Fixing Tension Member TM Place the TM on the TM Base and close it with the TM nut Tighten it using a screwdriver or hand with proper strength Note Do not screw strongly too much 11 Tray Fixing Fix not using trays on the tray support using tray fixing hinge Please note keep 70 degree between trays AEEA H BER OPTIC SPU CECLOSURE Dome Type Fiber optic Splice Closure VSOF BS810A User manual 12 Protection Tube Fixing Fix the protection tube with cable tie 13 Store the Exceeding loose tube Store the exceeding loose tube in the Spool and fix them with cable tie 14 Splicing amp Storing Fibers Splice fibers using an approved fiber splicing method After the splice insert sleeves in each slit accordingly Coil surplus fibers in the tray in a figure 8 Shape 15 Fiber Arrangement After the arrangement close the tray lid and record each splice on the index card on the lid Wrap the silver foil tape around the cable 8cm from the inlet port to protect cable sheath form the burner Be careful not to damage the silver foil tape i vv 1H aml dnatfinedli tiik Push the heat shrink tube up to the cable inlet port end and heat the tube staring at the inlet port moving away from it while controlling the fire 20 Hanger connection Connect the hangers to the hanger connecting part with bolts and nuts as the figure shown Hang the closure on the wire properly using aerial hangers
3. H BER CP TIC SPL CE CLOSURE Dome Type Fiber optic Splice Closure VSOF BS810A User manual Cleaning tissue Sillca gel Silver foil Protection tube 1 3 5 Removing Loose tube Leave 4cm from the cable end and remove the rest of loose tubes Clean the cut area using jelly cleaner 6 Inserting Protection Tube Insert fibers into the provided protection tubes after cutting into each 7 Inserting Heat Shrink Tuber Insert the cable into the heat shrink tube from the loose tube end Note check the insertion direction 8 Cutting Cable Inlet Ports Select the appropriate cable inlet ports and cut less than 3mm from the ports end with a saw VISSEM OFC 810A Emanual Rev 1 TEL 031 288 3484 FAX 031 283 7844 All rights reserved by VISSEM Electronics Co Ltd Opticube 1 Marking a Cutting Point Mark a sheath removing point on the cable with a piece of tape at a 120cm point from the cable cut end 2 Sheath Removing Remove the cable sheath from the marked point using a sheath stripper 3 Remove the cable sheath Remove plastic tape and dummy fillers tubes After trimming off dummy filler tubes clean the loose tube with jelly cleaner 4 Cutting Tension Member Leave 8cm from the cable end and cut off the tension member Length of Tension Member 8Cm 9 Cable Insertion Insert the cable into the inlet port from the end Note Port VS Cable Diameter 08 023 B Single 012 02
Download Pdf Manuals
Related Search