Manual - ICP DAS USA`s I
Contents
1. NS 200WDM Series 10 100Base TX Ethernet to 100Base FX WDM Single Strand Fiber Optic Converters Introduction Using the fiber optic medium for Ethernet applications has become more popular due to fiber optic s excellent physical features especially for long distance networks However fiber optic cable is very expensive so if we can apply a solution that uses only 1 cable instead of 2 the infrastructure cost can be cut in half The NS 200WDM Series provides a solution that reduces your expense by 50 The NS 200WDM Series of Single Strand Fiber Converters supports Wavelength Division Multiplexing WDM technology that allows two independent data communication channels to transmit and receive over one standard single mode and fiber optic line This not only doubles your existing bandwidth but also effectively reduces the cost of creating a new fiber optic infrastructure 50 Cost Saving for Fiber Optic Infrastructures With a pair of NS 200WDM series products NS 200WDM A and NS 200WDM B you can double the utilization of your existing costly fiber optic cable and save 50 of the cost of a newly installed fiber optic application It contains soft start function with overload protection high low voltage protection The width of the NS 200WDM is just 32mm so it can be used where space is important Features e Automatic MDI MDI X crossover for plug and play e Each port supports both 10 100 Mbps speed auto negotiatio2. eiving 1310um TX 100Base F 1310um RX 100Base FX 10 1 00Base T X 10 100Base T X NS 200FCS NS 200FCS IPAC 8447 Single Strand Fiber Converter Solution Wavelength Division Multiplexing WDM supports bi directional data transmission and receiving using dual wavelengths 1310 1550 nm over a single strand of single mode optical fiber R 1550 um 1310 um BM 10 1 00Base T x ROCIO SRD TX amp RX NS 200WDM A NS 200WDM B iPAC 8441 NS 200WDM User s Manual Version 1 0 Mar 2007 2 Checking Power Since the NS 200WDM consumes 2 9W Max ensure that your power supply is able to meets this demand The Input voltage range is between 10 and 30VDC External power supply is connected using the removable terminal block as shown below Bottom Panel Left Panel E F G 1 IGND vs Pin Function For Terminal Block External power supply is connected using the removable terminal block Vs Power input 10 to 30V GND Ground F G F G stands for Frame Ground protective ground It is optional If you use this pin it can reduce EMI radiation improve EMI performance and ESD protection Terminal Terminal Block lt Block Full Half Duplex Selection For all ICPDAS NS 200 series There are two modes of data transmissions full duplex and half duplex transmission The data can be transmitted in both directions on a single carrier at the same time when you select Full duplex
3. mode But the data can only be transmitted in one direction on a single carrier at the same time when you select Half duplex mode You may select Full or half duplex mode according to your equipment requirement You can configure full or half duplex NS 200 Series via DIP Switch Default full duplex Full duplex Default Transmission Distance 15km E DIP Switch Important Note NS 200WDM A NS 200WDM B and NS 200FCS only support Full duplex mode NS 200WDM User s Manual Version 1 0 Mar 2007 3 Dimensions The width of the NS 200WDM is just 32 mm so it can be used where space is important 107 0 Left Side View Right Side View Unit mm Bottom View Back View Ordering Information Important Note You must purchase both NS 200WDM A and NS 200WDM B since these products work as a pair NS 200WDM User s Manual Version 1 0 Mar 2007 4
4. n e Store and forward architecture e Full duplex IEEE 802 3x and half duplex backpressure flow control e Supports 10 30V DC voltage e Supports operating temperatures from 0 C 70 C e DIN rail mount for industrial usage NS 200WDM User s Manual Version 1 0 Mar 2007 1 Specifications e Compatibility IEEE 802 3 IEEE802 3u IEEE802 3x e Interface 10 100 Base T X and 100 Base FX Ethernet Port 10 100 Mbps x 1 Fiber Optic Port 100 Mbps x 1 SC Connector Single mode e LED Indicators Power LNK ACT 10 100M FDX Fiber Port e ESD Protection 8 KV Contact Discharge 15KV Air Gap Discharge e Single mode fiber cables 8 3 125 8 7 125 9 125 or 10 125 um Distance 15km 9 125 um recommended for full duplex Wavelength TX 1310 RX 1550 nm for NS 200WDM A TX 1550 RX 1310 nm for NS 200WDM B Min TX Output 14 dBm Max TX Output 8 dBm Sensitivity 31 dBm Max e Ethernet Cables 10 Base T Cat 3 4 5 UTP cable 100m Max 100 Base TX Cat 5 UTP cable 100m Max e Environment Operating temperature 0 C 70 C Storage Temperature 20 85 C Relative Humidity 10 to 90 non condensing e Dimensions 32 x 107 x 89 5 mm W x H x D e Power requirements 10 to 30Vdc Removable Terminal Block e Power consumption 0 12A 24Vdc 5 arrowed Application Note General Media Converter Solution Ageneral media converter requires a pair of fiber optic cables for data transmission and rec
Download Pdf Manuals
Related Search