Rosco STSK7665 Manual
Contents
1. subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation E 1 3 1 High voltage is within the monitor and opening of enclosure is only allowed to professionals 2 Do not watch video while driving A few highlights or dark spots may occur on the LCD screen It is a very common phenomenon to the active matrix display technology and never necessarily means any defects or faults Never try to repair this machine by yourself In case of any fault or failure please turn off the display at once and notify our company or the corresponding dealer The monitor is made up of many precise electronic components Any disassembly or modification may lead to damage or broken Front view 1 Dim Reduces the brightness to prevent glare Switching the monitor to day mode or night mode 2 Volume 8 Menu Control Increases amp Decreases Volume amp Adjust Menu settings 3 Menu Switches to setup mode See p 8 for options 4 Power 5 Auto Dimming Sensor COLOR BACKUP CAMERA SYSTEM STSK7665 INTRODUCTION Please read this manual thoroughly This manual contains instructions to make the installation of the camera and monitor easier The color backup camera system is a supplement to standard rear view mirror systems and will provide additional rear view vision when installed and m2. Switched Accessory u GROUND WIRE BLACK To metal point of the vehicle CAM1 REVERSE Trigger 1 a GREEN O Note For typical installation this trigger wire should be connected to the vehicle s back up lights circuit and the rear view camera should be attached to the connector as shown 14 NOTES NOTES NOTES ROSCO QUALITY POLICY Rosco Vision Systems is committed to providing customer satisfaction and quality products supported by employee participation and continuous improvement through the Quality Management System VisionSystems 90 21 144th Place Jamaica NY 11435 www roscovision com Ph 1 800 227 2095 Fx 1 718 297 0323 ISO 2001120009 FM 78496 Century of QS 9000 March 1998 FM 78495 E Printed in China Automotive Safety Lit P N 04242012
3. a 20mm 0 8in diameter hole only Feed as much cable as possible into vehicle and clamp securely This reduces the possibility of it being hooked or snagged Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components Camera Drill a 20mm 0 8in diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply sealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle Monitor The monitor terminates in a 13 pin connector which should be connected to the mating 13 pin receptacle end of the power video audio distribution harness For typical rear view installation connect the camera extension cable from the rear view camera to the 4 pin connector The green wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse FUEL TANKERS amp OTHER SPECIALTY VEHICLES All electrical equipment fitted to petroleum vehicles must be connected via battery master switch and must be isolated from the battery while the vehicle are loading and unloading For other specialty vehicles please check applicable code and regulations prior to installation 10 Always consult your dealer when fitting any electrical or electron
4. IGHTNESS OPERATING TEMPERATURE STORAGE TEMPERATURE WEIGHT OUTER DIMENSIONS WxHxD DISCLAIMER CMOS 1 3 OV7949 NTSC 510 H x 496 V PAL 626 H x 586 V NTSC 0 232x0 165in 5 9mm x 4 2mm 1 3 inch INTERNAL 380 TV LINES 0 LUX MINIMUM F1 2 MINIMUM 48dB AT AGC OFF 9V 12Vdc 1 5W AT 12Vdc MAX 150 110 D 98 H 82 V 4 F to 149 F 20 C to 65 C 22 F to 176 F 30 C to 80 C 400g 0 88lb 3 54 x 2 76 x 3 39in 90 x 70 x 86mm COLOR TFT LCD 55 LEFT RIGHT 35 TOP 55 DOWN 10W 560mA MAXIMUM 12 32Vdc PAL NTSC COMPOSITE VIDEO SINGLE 1VP P 75 OHM 1440 H x 234 V 350 1 250cd m2 14 F to 140 F 10 C to 60 C 13 F to 176 25 C to 80 C 337g 0 63115 6 8 x 4 9 x 7in 172 x 126 x 20mm without flush mount The use of the STSK7665 Vehicle CCTV system should not in any way be used as a substitute for careful and cautious driving Always obey traffic laws and motor safety regulations must always be adhered to Specifications subject to change without any notice Fig 1 Camera mount in suggested location Mount camera assembly high Centered Camera mounting hole pattern 60 30 THRU Fig 2 Position of camera Vehicles behind truck Street Rear Bumper Typical monitor image of view from properly installed camera 11 Fig 3 Optional wind deflector 12 Fig 4 POWER INPUT LEAD RED To Ignition
5. VisionSystems Safe T Scope 7 Rearview Backup Camera System INSTALLATION USER S MANUAL STSK7665 90 21 144th Place Jamaica NY 11435 1 800 227 2095 www roscovision com 9 WARNING 1 To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are dangerous voltages inside the monitor There are no user serviceable parts inside 2 Avoid exposing monitor to water rain moisture etc It is NOT waterproof Any moisture inside the monitor could cause extensive damage 3 Do not disassemble the camera This voids the warranty Disassembling the camera will compromise the waterproof seal 9 STORAGE 1 Do not expose the monitor to excessive heat or cold The storage temperature of this machine is 13 F to 176 F and operating temperature is 14 F to 140 F 2 Do not store or operate in humid environments 9 GENERAL 1 This system is intended for use in automotive applications Power source should be an automobile storage battery 12V 24V 2 Make sure all cables are connected properly Improper cable connections may damage the monitor Remove the cable connection when you do not intend to use the unit for a long period of time 3 Please install this system according to the instructions in this manual 4 Connect the system to an ignition switched power source Connection to an unswitched battery source will reduce battery life This device complies with Part 15 of the FCC Rules Operation is
6. aintained properly It is not intended in any way to be a substitute for careful and cautious driving All applicable traffic laws and motor vehicle safety regulations must still be obeyed FEATURES STSC108 CAMERA CMOS Camera e lt 1 Lux sensitivity 18 IR LED Field of view 110 Diagonal Back Light Compensation BLC e Automatic electronic iris provides a clearer more consistent image in low and bright light Compact and lightweight design installs easily into most vehicles e Waterproof dustproof IP69 rating e Wind deflector reduces buildup of dirt on lens STSM213 TFT LCD COLOR 7 MONITOR e Menu Control for Picture System and Options One Camera Power stand by switch Powerful built in speaker Auto Day Night Mode CONTENTS OF COMPLETE SYSTEM 1 Camera with Accessories Mounting Bracket w hardware Wind Deflector 65 Camera extension cable 1 Monitor with Accessories Flush Mount Duckfoot universal bracket for surface mounting of monitor on dashboard or headliner including adhesive pad Power Video Audio Distribution harness INSTALLATION INSTRUCTIONS Note The following instructions are for typical rear view application STSC108 CAMERA 1 2 Attach camera bracket close to rear marker lights centered on vehicle see Fig 1 Attachment point must be sturdy enough to support camera and bracket We do not recommend mounting the camera near the lower area of the
7. ic equipment to a vehicle fitted with a CAN bus or multiplex system FUNCTIONS AND OPERATION MONITOR 1 POWER If the monitor is switched off press the Power switch to switch the monitor on the picture appears Test if the mirror function is correctly set The setting should be such that an obstacle behind the vehicle on the right also appears on the right in the monitor Press the main switch Power to switch off the monitor The picture disappears VOLUME You can set the volume to amplify or mute the noises transmitted by the camera Press the button to reduce the volume Press the button to increase the volume MENU Button See Press the MENU button once to set desired brightness Press the MENU button twice to set desired contrast Press the MENU button three times to set desired color Press the MENU button four times to set desired language Press the MENU button five times to reset default settings for all parameters Press the MENU button six times for Camera 1 Normal or Mirrored view HOW TO SET YOUR MONITOR TO YOUR REQUIREMENTS NOTE On screen menu commands may only be selected when monitor is in Steady on green light mode When monitor is in standby mode and activated by trigger sig nal on screen menu commands are disabled To set monitor to suit your requirements proceed as follows e Press the MENU button once to set the desired brightness Pres
8. s the button to reduce the brightness Press the button to increase the brightness Press the MENU button twice to set the desired contrast Press the button to reduce the contrast e Press the button to increase the contrast Press the MENU button three times to set the desired color Press the button to reduce the tint e Press the button to increase the tint e Press the MENU button four times to set the desired language Press the button to go back Press the button to go forward e Press the MENU button five times to reset the default settings for all parameters e Press the button to deactivate reset default settings e Press the button to activate reset default settings Press the MENU button six times for Camera 1 e Press the to turn on Mirror or Normal View Press the to turn on Mirror or Normal View SPECIFICATIONS STSC108 CAMERA PICK UP DEVICE TV SYSTEM PICTURE ELEMENTS SENSING AREA IMAGE SIZE SYNCHRONIZATION HORIZONTAL RESOLUTION REQUIRED ILLUMINATION SIGNAL TO NOISE RATIO POWER SUPPLY POWER CONSUMPTION CURRENT CONSUMPTION LENS ANGLE OPERATION TEMPERATURE STORAGE TEMPERATURE WEIGHT DIMENSIONS W x H x D STSM213 MONITOR SCREEN 7 0 inch 178mm VIEWING ANGLE POWER CONSUMPTION POWER SOURCE TV SYSTEM VIDEO INPUT OUTPUT RESOLUTION CONTRAST BR
9. vehicle ex bumper This reduces the view of the camera and increases the chance of physical damage to the camera Attach camera to bracket using screws provided Adjust angle as indicated in Fig 2 Use rear bumper and back of vehicle as a reference point Wind deflector may be installed This deflector is designed to reduce the buildup of dust dirt and moisture on the camera lens See Fig 3 STSM213 MONITOR 1 Attach monitor inside vehicle in a location convenient to the driver ex center of dash overhead or flush mounted in dash 2 Attach the duckfoot bracket to the dashboard or to the headliner using self tapping screws and or adhesive pad 3 Fasten monitor to duckfoot and adjust mounting angle to allow optimum driver viewing comfort See Fig 4 CABLE 1 Be sure to position the cable properly The male end attaches to the camera The female end attaches to the power video audio distribution harness typically located under the dashboard See Fig 5 2 Do not run the cable over sharp edges or corners Do not kink the cable Keep the cable away from hot and rotating parts 3 Fasten all cable runs and secure all excess cable WIRING CAMERA AND MONITOR Connect the red wire to an ignition switched accessory ex radio power source and connect the black wire to chassis ground See wiring diagram for connections See Fig 5 Before drilling be sure no cable or wire is on the other side Be sure to drill
Download Pdf Manuals
Related Search