cs2 user manual - Inspire Fitness
Contents
1. 14 ENGAGING THE CHILD SAFETY LOCK ASSEMBLY 1 ALWAYS engage the CHILD SAFETY LOCK ASSEMBLY after each use by clipping the hook onto the loop located UNDERNEATH the LEFT PEDAL ASSEMBLY see FIGURE B below 2 Before each workout disengage the hook from the loop The CHILD SAFETY LOCK ASSEMBLY can hang freely during your workout and will not interfere with the mechanism 16 COMPUTER OPERATION AND FEATURES This unit is equipped with a Telemetric Heart Rate transmitter that allows the user to monitor their heart rate while wearing a Chest Strap A Chest Strap may be purchased from Inspire by calling 877 738 1729 In addition this computer is equipped to mount and power a tablet computer as shown below During use your tablet may mount on the rubberized tablet rack A USB located on the left side of the computer can supply up to 1A of current for recharging 17 BASIC OPERATION e Press QUICK START to immediately begin workout in Manual Mode e Press the STOP RESET key at any time to PAUSE the workout Press ENTER to resume exercise Press STOP RESET twice to reset program e Press and hold the STOP RESET key for 2 seconds to RESET the computer e RESISTANCE Press the UP or DOWN key to change the Resistance Level during a workout The Resistance may be adjusted from LEVEL 1 Lowest to LEVEL 20 Highest The Resistance level is displayed in the top center of the LCD yo X N ANN 4 fl f2. B Place the Right Swing Arm Assembly 47 on top of the Styrofoam Support Block with Red Dot so the ball bearing connection assembly sits on top of the Styrofoam Support Block C Secure the right Pedal Crank Arm Assembly 142 to the Right Swing Arm Assembly 47 as shown below using qty 6 Curved Washers 29 and qty 6 M8x16 socket screws 31 zz oc 1 D Place Left Swing Arm Assembly 54 on Front Pivot Shaft of main frame Secure using qty 1 Oversized Flat washer 44 and qty 1 M8x20 Hex Bolt 43 NOTE When assembling Swing Arm put finger inside the Bearing Pivot to ensure spacer is centered Without the Spacer centered you will not be able to place the Pedal Arm on the Shaft E Place the left Pedal Crank Arm Assembly 142 on top of the Styrofoam Support Block with Red Dot so the ball bearing connection assembly sits on top of the Styrofoam Support Block F Secure the right Pedal Crank Arm Assembly 142 to the Right Swing Arm Assembly 54 as shown below using qty 6 Curved Washers 29 qty 6 Lock Washers 32 and EN le 12Pcs 59 STEP 3 See FIGURE 3 A Assemble Seatback 8 onto Seat Slider Assembly Align lower holes and secure using qty 1 cap nylon nut 140 qty 1 M8 Flat Washers 33 and qty 1 M8 x 70mm Socket Screws 139 Choose a preferred Seatback Recline Angle The seatback 8 may be installed in 3 different Recline Angles UPPER MIDDLE LOWER based
3. FOCUS PROGRAM SETUP e Press PROGRAMS Press UP or DOWN to scroll through the PROGRAMS o UPPER BODY FOCUS Focusing on upper body workout including the chest back and arms Also includes lower body workout o ARMS FOCUS Focusing on upper body workout only Feet remain on pegs e After selecting your FOCUS program press START 22 LEVEL Press UP or DOWN to set maximum resistance level This resistance will not go above this level during the workout You may adjust the maximum resistance during your workout Press ENTER to accept maximum resistance level Press STOP RESET to go back to PROGRAM selection PERE Si WORKOUT TIME Press UP or DOWN to set total workout time Press ENTER to accept workout time and begin workout Press STOP RESET to go back to LEVEL 23 USERS Allows up to 4 different users to enter personal information and save a preferred workout Computer will save each user workout totals to keep track of accumulated user data Total Workout Time Total Distance Total Calories ness I nspire e Press the USER button at startup Press the UP and DOWN key to toggle through USER 1 USER 4 GER e Press QUICK START to immediately begin workout for that user If no data exists for user the computer will prompt you to CHANGE USER SETTINGS Press STOP RESET to go back to MAIN DISPLAY e Press ENTER to go to CHANGE USER SETTINGS SHEET 23 24 Press and hold ENTER for 2 seconds to go to US
4. 110 220 Singapore 130 RC802 630 001 M Transformer VAC 1 PCS 131 RC800 391 007 Plastic sleeve D10 41 5 1 PCS 132 0114 142 558 Phillips self tapping screw ST4 2 55 1 PCS 134 0114 742 068 Philips washer head screw ST4 2 6 F Type 6 PCS 135 RC800 561 005 Child safety lock D2 5 D8 156 1 SET 137 RC802 891 002 Hardware Pack rev 2013 1 SET 138 Crank Removal Tool S19 1 SET 139 0113 208 708 Allen head bolt M8 70 1 PC 140 0110 808 008 Cap Nylon nut M8 1 PCS 141 BTBRCCPO001 14 INSPIRE CS2 STICKER 190 18mm 2 PCS 142 RC802 240 002 Crank Pedal Tube Assembly 2 SET 143 RC802 350 002 Heart Rate Handlebar Assembly 1 SET 144 0113 306 128 Flat head screw M6 12 Black Zinc 4 PCS 145 RC802 630 001 Pulse sensor wire 2 PCS 146 0110 406 003 Flange Nut M6 4 PCS 147 0113 104 108 Cross recessed pan head screws M4 10 4 PCS ALTERNATE PLUG OPTIONS to be ordered separately TYPE PART NUMBER COUNTRIES PHOTO United States Japan Phillipines A type l RC802 63 1 002 Canada Columbia Ecuador included with Transformer Honduras Mexico Panama Peru Taiwan I type RC802 631 003 Australia New Zealand China Europe Argentina Russia gt C type RC802 631 004 Brazil Egypt India Indonesia eee Israel Pakistan South Korea South Africa a Ey RC802 631 005 United Kingdom Hong Kong Lr j u 2 29 z a 2 z m o co N 30 31 Warrant
5. Inspire SZ Fitness HANDLE POSITION TARGET HEART RATE E 88 8 3 20 30 40 50 60 70 so 90 100 sita 3295338 CardioStrider ed eS WWA A UNA PROGRAMS TIME wwuinspirefitness net VIEW hold to scan e VIEWING WORKOUT DATA During a workout RPM and CALORIES are displayed on the scrolling text bar Press the PROGRAMS and USERS buttons at the same time to display WATTS and DISTANCE Press and hold the PROGRAMS AND USERS buttons for 2 seconds to turn on Autoscan the computer will switch between RPM CALORIES and WATTS DISTANCE every 10 seconds 18 STANDARD PROGRAMS The CS2 CardioStrider has 6 Standard workout programs that will automatically adjust the resistance ate eo os Pitty HA 99999999909990999099099 Cardiogtrider VIEW held to scan m eS I A www inspirefitness net e Atstartup press PROGRAMS Press UP or DOWN to scroll through the PROGRAMS ROLLING HILL e sex eee 00990099099909009990 ROLLING HILL PEAK PLATEAU MOUNTAIN CLIMB HILL INTERVAL o STRENGTH INTERVAL e After selecting your program press ENTER 00000 19 e LEVEL Press UP or DOWN to set maximum resistance level The resistance will not go above this level during the workout You may adjust the maximum resistance during your workout Press ENTER to accept maximum resistance level Press STOP RESET to go back to PROGRAM selection LEVE
6. Screws 49 Slide on Water Bottle C Pull Grip Heart Rate wires 145 through front hole in Console Mast 39 and pull up through top hole Attach Grip Heart Rate Assembly 143 to Console Mast 39 using qty 4 Flat Head Screws 144 D Connect console connectors A B to connectors 37 144 E Attach Computer Console 19 to Console Mast 39 using qty 4 screws 17 NOTE Screws 17 are pre installed in the Computer Console 19 NOT in the hardware pack F Connect Console Mast connector 37 to Main Frame Cable Connector 85 as shown in Figure 6 A G Slide Console Mast 39 onto the Main Frame 34 NOTE Make sure not to pinch the cable assembly when assembling the console onto the mounting bracket H Secure Console Mast 39 onto the Main Frame 34 using qty 4 Flat Washers 33 flat sides of tube qty 2 Curved Washers 29 curved front of tube and qty 6 M8x16mm Screws 31 L Remove protective films from Console button overlay both top and bottom J Insert the Power Adapter 130 into the Rear Power Input Connector on Main Frame as shown in FIGURE B Plug Power Adapter into power source Computer LCD should turn on and sound a long beep FINAL STEP Unscrew levelers on Front Stabilizer Assembly 62 so that both sit flat on the ground Unscrew center leveler located under the center point of the unit so that is touches the ground Failure to do so could cause damage to your unit
7. handle L 1 PCS 81 RM610 881 101 Buffer pad 30 30 15 1 PCS 82 RC800 201 019 Rail Chrome 1 PCS 84 0114 129 068 Phillips self tapping screw ST2 9 6 6 PCS 85 RC802 630 001 I Data Cable Main Rev 2013 1 PCS 86 RC800 801 009 Rail cover 1 PCS 91 RC800 801 004 Main Cover R 1 PCS 92 RC802 391 002 Upper mounting bracket R 6 2 0 rev 2013 1 PCS 93 BE760 881 001B Disc Cover 80 2 PCS 96 RC800 221 005 Hex Nut M16 1 0 1 PCS 97 RC800 221 004 Spacer 3 1 PCS 98 0200 310 53 Bearing 6004ZZ 2 PCS 99 RC800 221 002 Spacer 1 1 PCS 100 BC770 801 011 Sensor Bracket 1 PCS 101 RC802 630 001 J Speed Sensor Cable 1 PCS 104 RC802 220 002 Pulley Assembly Aluminum p260 J6 rev 2013 1 PCS 106 0249 200 46 Belt 460 J6 1 PCS 109 RC802 630 001 K Power Input Receptacle Cable rev 2013 1 PCS 110 RC802 391 001 Upper Mounting Bracket L 6 2 0 rev 2013 1 PCS 111 RC800 801 003 Main Cover L 1 PCS 112 RC800 39 1 004 Lower mounting bracket R 6 2 0 rev 2013 1 PCS 113 0114 142 198 Phillips self tapping screw ST4 2 19 3 PCS 115 RC802 630 001 L Lower Control Board Rev 2013 1 PCS 116 RC800 801 005 Base tube Cover L 1 PCS 117 RC800 801 007 Front Cover L 1 PCS 118 BC680 801 010A End cap 2 PCS 119 0113 706 162 Allen Head Screw M6 16 rev 2013 4 PCS 120 as en EMS Fly Wheel Idler Assembly 9 kg rev 2013 1 SET 127 RC802 391 003 Lower Mounting bracket L 6 2 0 rev 2013 1 PCS 128 RC800 801 008 Front Cover R 1 PCS 129 RC800 801 006 Base tube Cover R 1 PCS 28 type A plug
8. in a range during a workout The computer will automatically adjust the RESISTANCE to keep the user heart within the selected range There are two available Heart Rate control programs FAT BURN Keeps your heart rate at 65 of maximum recommended for your AGE CARDIO Keeps your heart rate at 80 of maximum recommended for your AGE Refer to the table located in the middle of the console for your recommended Heart Rate The approximate value is based on the users AGE however you should always consult with a physician before beginning heart rate programs 21 TARGET HEART RATE NOTE Heart Rate Control Programs should only be performed using a Heart Rate Chest Belt for accuracy To order a Heart Rate Chest Belt call Inspire Fitness at 877 738 1729 HEART RATE PROGRAM SETUP o Press PROGRAMS and press UP or DOWN to find HEART RATE Press ENTER o Press UP or DOWN to toggle between FAT BURN and CARDIO Press ENTER to select o AGE Press the UP DOWN key to select your AGE Press ENTER to accept AGE and move to WORKOUT TIME o WORKOUT TIME Press UP DOWN to select WORKOUT TIME Press ENTER to accept WORKOUT TIME and begin 3 minute warmup Every Heart Rate Control Workout includes a 3 00 Warmup and a 5 00 Cooldown period in addition to the selected workout time NOTE During a Heart Rate Control Workout press UPIDOWN to adjust your Target Heart Rate The RESISTANCE cannot be directly controlled during a Heart Rate Control Program
9. this warranty under normal personal family or household use In repairing the product Inspire Fitness may replace defective parts with at the option of Inspire Fitness serviceable used parts that are equivalent to new parts in performance or new parts All exchanged parts and products replaced under this warranty will become the property of Inspire Fitness Inspire Fitness reserves the right to change manufacturers and or specification of any part to cover any existing warranty Service procedures To obtain warranty parts you must return the parts to Inspire Fitness or an authorized Inspire Fitness retailer in its original container or equivalent You must pre pay any shipping charges taxes or any other charges associated with transportation of the product In addition you are responsible for insuring any product shipped or returned You assume the risk of loss during shipment You must present Inspire Fitness with proof of purchase documents including the date of purchase Model and Serial Number Any evidence of alteration erasing or forgery of proof of purchase documents will be cause to void this warranty You may be charged a trip charge if you are outside a reseller s service area Register your warranty online visit www inspirefitness net Conditions and Exceptions This warranty does not extend to any product not purchased from Inspire Fitness or from an authorized Inspire Fitness reseller Labor claims must be authorized prior to pe
10. CS2 CARDIOSTRIDER en de gt E 4 Z lt 5 un gt TABLE OF CONTENTS BEFORE YOU BEGIN 1 IMPORTANT SAFETY NOTICES 2 CONTENTS OF PACKAGING 3 WARNING LABEL PLACEMENT 4 HARDWARE PACK 5 ASSEMBLY INSTRUCTIONS 6 17 COMPUTER OPERATION GUIDELINE 18 27 PARTS LIST 28 30 ALTERNATE PLUG PART NUMBERS 30 EXPLODED DIAGRAMS 31 33 WARRANTY 34 35 BEFORE YOU BEGIN Thank you for selecting the INSPIRE CS2 CARDIOSTRIDER For your safety and benefit read this manual carefully before using the machine As a manufacturer we are committed to providing you complete customer satisfaction If you have any questions or find there are missing or damaged parts please call our TOLL FREE customer service number Our Customer Service Agents will provide immediate assistance to you HEALTH IN MOTION LLC 4945 EAST HUNTER AVE ANAHEIM CA 92807 Toll Free Customer Service Number 1 877 738 1729 Mon Fri 8 a m 5 p m PST www inspirefitness net IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety However certain precautions apply whenever you operate a piece of exercise equipment Be sure to read the entire manual before you assemble or operate your machine In particular note the following safety precautions e Keep children and pets away from the machine at all times DO NOT leave children unattended in the same room with the machine The linkages on this machine can cause
11. ER DATA SHEET 24 CHANGE USER SETTINGS GENDER Scrolling message reads GENDER 1 time then displays FEMALE Press the UP or DOWN buttons to toggle between FEMALE and MALE Press ENTER to accept setting and move to AGE Press RESET to go back to CHANGE USER SETTINGS FEMHLE AGE Scrolling message reads AGE 40 Press the UP or DOWN key to adjust the AGE value in 1 year increments Press ENTER to accept setting and move to WEIGHT Press STOP RESET to go back GENDER WEIGHT Scrolling message reads WEIGHT 175 Press the UP or DOWN key to adjust the WEIGHT value in 5 Ib increments Press ENTER to accept WEIGHT and go to PROGRAM SELECTION Press STOP RESET to go back to AGE NEN E PROGRAM SELECTION See Program Selection on page 17 25 USER DATA A scrolling message reads USER DATA I time Press the UP DOWN to toggle between ACCUMULATED and CHANGE NAME Press ENTER CHANGE NFM CHANGE NAME USER 1 4 may be changed to a CUSTOM user name 000000 A blinking underscore Press the UP or DOWN key to select letter or number Press ENTER to accept letter or number and move to next location Press the RESET key to move back to the previous location 66 99 is used to show the current location A Maximum of 8 alpha numeric characters may be used After pressing START past at 8 space USER NAME is set ACCUMULATED USER workout data is saved in the computer mem
12. HALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INSPIRE FITNESS IS NOT RESPOSIBLE FOR THE REPAIR OR REPLACEMENT OF ANY PARTS THAT INSPIRE FITNESS DETERMINES HAVE BEEN SUBJECTED AFTER THE DATE OF MANUFACTURE TO ALTERATION NEGLECT ABUSE MISUSE NORMAL WEAR amp TEAR ACCIDENT DAMAGE DURING TRANSIT OR INSTALLATION FIRE FLOOD OR ANY ACT OF GOD SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU This warranty gives you specific legal rights and you may also have other rights that may vary from state to state This is the only express warranty applicable to Inspire Fitness Inspire branded cardio products Inspire Fitness neither assumes nor authorizes anyone to assume for it any other express warranty 34
13. LS ES ses LEA 00990099099999009090 e WORKOUT TIME Press UP or DOWN to set total workout time Press ENTER to accept workout time and begin Press STOP RESET to go back to LEVEL NOTE The WORKOUT TIME may be changed during a workout by pressing the TIME key Press UP DOWN to modify the WORKOUT TIME Press ENTER to begin workout The CS2 CardioStrider has 2 programs to focus workout on your upper body Upper Body Focus Arms Focus During the workout the computer will beep and a scrolling message will give you instructions UN PEGS HEART RATE 000009 0 9909900000900000 0 20 A list of messages and their definitions are described below INVERTED HANDLES Place handles in inverted position This will focus on your biceps and triceps muscles UPRIGHT HANDLES Place handles in upright position This will focus on your chest and back muscles UPRIGHT HANDLES e N y 2 bi 2 p ga U r E 4 A Jun NC 3 gt x SAL gt Aes 2 PU o it ls rr be 4 L f a Sande 24 FEET ON PEDALS Place feet on the moving pedals FEET ON PEGS Place feet on the pegs Round tube located at the front of the unit PALMS UP In INVERTED MODE keep palms facing upward to focus workout on the biceps muscle PALMS DOWN In INVERTED MODE keep palms facing downward to focus workout on the triceps muscle HEART RATE PROGRAMS Heart Rate control programs allow the user to keep their heart rate
14. PCS 31 0113 008 168 Allen head bolt M8 16 33 PCS 32 0116 308 010 Spring washer 08 24 PCS 33 0116 008 010 Flat Washer pS 19 PCS 34 RC802 200 001 Main Frame Rev 2013 1 PCS 35 RC800 401 001 Seat 1 PCS 36 RC800 801 001 Outer Cover L 1 PCS 37 RC802 630 001 F Lower sensor wire Rev 2013 1 PCS 39 RC800 350 001 Computer Post With Heart Rate 1 PCS 42 RC800 330 003 Handlebar L Assembly 1 PCS 43 0111 008 208A Allen Head screw M8 20 4 PCS 44 0116 208 508A Large Flat Washer p8 p28 4 PCS 47 RC800 300 002 Swing Arm R 1 PCS 48 RC800 801 015 Philips screw M6 12 2 PCS 49 0113 105 108 Cross recessed pan head screws M5 10 6 PCS 51 RC800 801 202 Spring Knob Black 2 PCS 52 0110 412 599 Flange Nut M12 1 25 2 PCS 53 RC800 801 010 Upper Pedal L 1 PCS 54 RC800 300 001 Swing Arm L 1 PCS 55 RC800 3 10 002 Pedal Tube R 1 PCS 56 0114 742 198 Philips self tapping screw ST4 2 19 30 PCS 57 0114 142 088 Philips Self tapping Screw ST4 2 8 F Type 24 PCS 58 RC800 801 013 Lower Pedal Cover R 1 SET 59 RC800 801 012 Upper Pedal Cover R 1 SET 27 61 RC800 801 020 Adjusting Foot Pad MIO 1 PCS 62 RC800 340 001 Front Stabilizer 1 PCS 63 RC800 301 009 Bushing p48 18 2 PCS 64 RC800 801 011 Lower Pedal Cover L 1 SET 65 RC800 310 001 Pedal tube L 1 PCS 70 RC800 380 002 Seat adjusting handle R 1 PCS 75 RC800 370 001 Seat support frame 1 PCS 80 RC800 380 001 Seat adjusting
15. The Frame and Seat Pad of the machine can be cleaned using a damp cloth and mild non abrasive detergent DO NOT use solvents WARNING BEFORE BEGINNING ANY EXERCISE PROGRAM CONSULT YOUR PHYSICIAN THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT NEITHER HEALTH IN MOTION LLC NOR FG1 LLC ASSUMES ANY RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT 2 CONTENTS OF PACKAGING 1 1 LEFT N WARNING PATENT LABEL PLACEMENT Manufactured Under Patents Patents Pending as follows US Patents 7 815 551 and 8 562 491 mn o OOR US Patent Pending 2013 14048302 F YOU FEEL UNUSUAL PAN OZ2NESS Canada Application 2696901 etat ne baee USE CONSULT YOUR PHYSICIAN IMMEDIATELY NEVER ALLOW CHILDREN OR PETS TO COME NEAR OR APPROACH THE MOVING LINKAGES WHILE IN USE Europe Application 08830164 3 MISUSE OR ABUSE OF THIS EQUIPMENT MAY THE LINKAGES ON THIS MACHINE ARE FLYWHEEL DRIVEN AND CAN CAUSE un LEAD TO SERIOUS INJURY OR DEATH SERIOUS INJURY OR DEATH IF SOMEONE BECOMES STUCK UNDERNEATH China Utility ZL 201220191127 2 DURING USE A ps CHILDREN AWAY FROM THIS NEVER PLACE FEET OR HANDS UNDER THIS LINKAGE DURING USE China Design ZL 201233139551 8 FOR ADULT USE ONLY ALWAYS ENGAGE CHILD SAFETY LOCK WHEN MACHINE IS NOT IN USE THIS EQUIPMENT IS INTENDED Internati
16. on the users preferred position Align upper seatback tube hole with preferred hole based on the below figure Secure using the pin b as shown in Figure 3 MIDDLE B Secure seat bottom pad 35 to Seat Slider Assembly using qty 4 Flat Washers 33 and qty 4 M8x16mm Socket Screws 31 10 STEP 4 SIDE COVERS see FIGURE 4 A Attach Right Side Cover 24 using qty 4 Phillips Head Washer Screws 23 Make sure crank can spin freely with no side cover interference B Attach Left Side Cover 36 using qty 4 Phillips Head Washer Screws 23 Make sure crank can spin freely with no side cover interference STEP5 HANDLE ASSEMBLY See FIGURE 5 A Slide Right Handle Assembly 21 into the Right Swing Arm Sleeve 47 Make sure the pop pin 51 is fully engaged WARNING Check to make sure the Right Handle Assembly has an R Sticker on it Accidental switching of the Right and Left Handle Assemblies can result in serious injury B Slide Left Handle Assembly 42 into the Left Swing Arm Sleeve 51 Make sure the pop pin 51 is fully engaged WARNING Check to make sure the Left Handle Assembly has an L Sticker on it Accidental switching of the Right and Left Handle Assemblies can result in serious injury 13 STEP 6 CONSOLE ASSEMBLY See FIGURE 6 A Wash Water Bottle 9 thoroughly with warm soapy water B Attach Water Bottle Cage 9 to Console Mast 39 using qty 2 Phillips Head
17. onal PCT US2008 076264 REPLACE THIS OR ANY OTHER WARNING LABEL IF DAMAGED ILLEGIBLE OR MISSING MAXIMUM USER WEIGHT 300 LBS 136 KG RISK OF ELECTRICAL SHOCK THIS UNIT IS TO BE USED ONLY INDOORS AND IN A DRY LOCATION USE ONLY WITH CERTIFIED POWER SUPPLY PROVIDED RATED 26V 2A The warning and patent labels have been placed on the unit in location shown If the labels are missing or illegible please call customer service at 1 877 738 1729 for replacements Apply the labels in location shown e the gt 135 1PC HRHERERERERERERERHEENERHE 31 22PCS own ruler or scale to mea your 32 12PCS ot drawn to scale Please use CARDIOSTRIDER HARDYYARE PACK 3 9PCS 139 1PC 140 1PC NOTE The following parts are n CARDIOSTRIDER ASSEMBLY INSTRUCTION STEP 1 FRAME STABILIZER ASSEMBLY See FIGURE 1 A Carefully unpack contents of box leaving the 3 large styrofoam frame support blocks in place Inside the packaging locate the Styrofoam block with Red Sticker packed near the Console Assembly Place aside for use in STEP 2 B Remove large styrofoam frame support from REAR portion of frame The Rear Stabilizer mounting bracket should now be exposed C Place Rear Stabilizer Tube Assembly 28 underneath the Rear Mounting Bracket Ensure that the transport wheels are facing backwards D Attach the Rear Stabilizer Tube to the frame as shown in FIGURE 1 wi
18. ory after each workout and added to the totals for that user User may view the workout totals for TOTAL WORKOUT TIME minutes TOTAL DISTANCE miles TOTAL CALORIES Press the UP and DOWN key to scroll through accumulated data WORKOUT TIME minutes DISTANCE miles CALORIES calories Press RESET to go back to USER DATA Press the ENTER to reset accumulated data A scrolling message reads RESET DATA 1 time A scrolling message reads NO Press the UP or DOWN key to toggle between NO and YES Press ENTER on YES to reset data to O and go back to USER DATA Press START on NO to cancel data reset and go back to USER DATA Press RESET to go back to USER DATA 26 PARTS LIST DETAILED F N PART NUMBER DESCRIPTION DESCRIPTION QTY UM 1 RC800 360 002 Backrest support tube 1 PCS 8 RC800 401 002 Backrest frame 1 SET 9 BC830 881 006J Water bottle Cage Assembly LMBG Qualified 1 PCS 16 0116 706 002 Lock Washer 6 Black Zinc Plating 4 PCS 17 RC802 630 001 E Bolt M5 10 4 PCS 19 RC802 630 001 Console Rev 2013 1 PCS 21 RC800 330 004 Handlebar R Assembly 1 PCS 23 TR511 561 038 Philips washer head screw M4 8 Black Zinc 8 PCS 24 RC800 801 002 Outer Cover R 1 PCS 27 0111 408 718 Carriage Bolt M8 70 4 PCS 28 RC800 341 002 Rear Stabilizer 1 PCS 29 0116 608 008 Arc Washer 08 18 PCS 30 0110 308 008 Cap Nut M8 4
19. rforming service or they may be denied This warranty does not extend to any product missing a serial number or with a serial tag that has been altered or defaced This warranty does not extend to service calls to correct installation of the equipment or instruct owners on how to use the equipment This warranty does not extend to any product that has been damaged or rendered defective a as a result of accident misuse or abuse b by the use of parts not manufactured or sold by Inspire Fitness c by modification of the product d as a result of service by anyone other than Inspire Fitness or an authorized Inspire Fitness warranty service provider e product that has not been properly maintained follow maintenance schedule found on product f as a result of neglect Should any product submitted for warranty service be found to be ineligible an estimate of repair cost will be furnished and the repair will be made if requested by you upon Inspire Fitness receipt of payment or acceptable arrangement of payment 33 Disclaimer EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY INSPIRE FITNESS MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE INSPIRE FITNESS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS WARRANTY NEITHER INSPIRE FITNESS NOR ANY OF ITS AFFILIATES S
20. serious injury or death if used improperly e Never place your hands or feet in the path of the linkages because injury may occur to you or damage may occur to the equipment Never allow children to come near or approach the moving linkages while in use e If the user experiences dizziness nausea chest pain or any other abnormal symptoms STOP the workout at once CONSULT A PHYSICIAN IMMEDIATELY e Position the machine on a clear leveled surface DO NOT use the machine near water or outdoors e Keep hands away from all moving parts e Always wear appropriate workout clothing when exercising DO NOT wear robes or other clothing that could become caught in the machine Running or aerobic shoes are also required when using the machine e Use the machine only for its intended use as described in this manual DO NOT use attachments not recommended by the manufacturer e Do not place any sharp object around the machine e Disabled persons should not use the machine without a qualified person or physician in attendance e Before using the machine to exercise always do stretching exercises to properly warm up e Never operate the machine if the machine is not functioning properly e Maximum user weight 300 Ibs e Allow 24 61 cm of space on each side of the unit Never place body parts under pivot area directly behind pedal CARE AND MAINTENANCE 1 Keep seat slider clean 2 Inspect and tighten all parts before using the machine 3
21. th qty 2 M8x70 carriage bolts 27 qty 2 M8 curved washers 29 and qty 2 M8 acorn nuts 30 E Remove large styrofoam frame support from FRONT portion of frame The front mounting bracket should now be exposed F Place Front Stabilizer Tube 62 underneath the front mounting bracket Attach the Front Stabilizer Tube 62 to the front mounting bracket as shown in FIGURE 1 Secure the right side with qty 1 M8x70 carriage bolt 27 qty 1 M8 curved washer 29 and qty 1 M8 acorn nut 30 Secure the left side with qty 1 M8x70 carriage bolt 27 qty 1 M8 curved washer 29 and qty 1 Child Safety Lock 135 NOTE The Child Safety lock should always be engaged when machine is not in use For instructions on how to engage the lock see sheet 15 of this user manual G Attach Right Cam Lock Handle 70 and tighten qty 2 socket screws a NOTE Ensure that the Right Cam Lock Handle has an R sticker on it H Attach Left Cam Lock Handle 80 using qty 2 socket screws a NOTE Ensure that the Left Cam Lock Handle has an L sticker on it STEP 2 SWING ARM ASSEMBLY See FIGURE 2 A Place Right Swing Arm Assembly 47 on Front Pivot Shaft of main frame Secure using qty 1 Oversized Flat Washer 44 and qty 1 M8x20 Hex Bolt 43 NOTE When assembling Swing Arm put finger inside the Bearing Pivot to ensure spacer is centered Without the Spacer centered you will not be able to place the Swing Arm on the Shaft
22. y This Warranty applies to Inspire Cardio products manufactured or distributed by Health In Motion LLC RESIDENTIAL WARRANTY 10 YEAR FRAME CS2 Includes Main Frame and Welds 3 YEAR PARTS all cardio units Excluding Paint and Finish unless defective out of box 1 YEAR LABOR all cardio units LIGHT COMMERICAL WARRANTY 10 YEAR FRAME Includes Main Frame and Welds 1 YEAR PARTS Excluding Paint and Finish unless defective out of box 1 YEAR LABOR Inspire Fitness warrants that the Product you have purchased from Health In Motion or from an authorized Inspire reseller is free from defects in materials or workmanship under normal use during the warranty period Your sales receipt showing the date of purchase of the Product is your proof of the date of purchase You must demonstrate proof of purchase to obtain a warranty This warranty extends only to you the original purchaser It is not transferable to anyone who subsequently purchases the product from you It excludes expendable parts such as paint and finish and cosmetic items including but not limited to the following grips seats and labels This Warranty becomes VALID ONLY ifthe Product is assembled installed following the instructions directions included with the Product Replacement and repair of parts During the warranty period Inspire will at no additional charge repair or replace the product if it becomes defective malfunctions or otherwise fails to conform with
Download Pdf Manuals
Related Search