YS-D2 - Sea & Sea
Contents
1. on page E 23 for details on taking photographs while connected using different cords il Strobe Setting Guide Connection cord Fiber optic cable with Without Digital pre flash es pre flash Pan eens 6 Light ood ial 11 step 11 step 11 step TTL Light level 1 The SEA amp SEA YS Converter optional is required For light level control while a YS Converter is connected adjust the levels on the YS Converter side N CAUTION f a sync cord is connected to the unit the automatic recognition function will be activated and fiber optic connection will be disabled even if a fiber optic cable is connected i Connecting with the Sync Cord When you want to use this strobe with a SLR housing which has a strobe converter bulkhead connect the strobe to the housing with s sync cord optional Some digital SLR housings require a SEA amp SEA converter optional for TTL photography Refer to your digital SLR housing instruction manual for details 1 Remove the connector cap from the sync cord and check the O ring strobe camera or housing Check the O ring to make sure there are no scratches or debris and apply a light coating of the included silicon grease 2 Remove the strobe s connector cap Z CAUTION Please attached the power is turned OFF when you are installing a synchro O GY Connector E 19 code There is a possibility of erroneously mm cap fire when mounting remains ON Connecting the Strobe 3 Align2. TTL photography Photography based on the camera s photometric data of the subject s brightness which is used to regulate the light amount of the strobe so that the correct exposure is achieved Even if the distance from the subject has changed the light amount will be controlled automatically and you can easily obtain the correct exposure After shooting with TTL automatic light control the TTL lamp will illuminate in green for approximately 2 seconds If the correct exposure cannot be obtained in TTL shooting mode switch to manual shooting mode E 23 Taking Photographs Using the Fiber optic Cable When you shoot with a digital camera set the built in flash of the camera to the forced flash mode The strobe will not fire unless the built in flash of the camera fires CAUTION Disable camera s red eye reduction function Disable camera s AF assist light Manual photography Light amount of the strobe can be adjusted with the light level control dial 1 Set the mode switch to or 4 When shooting with a digital camera that pre flashes set to 44m When shooting with a digital camera that does not pre flash set to fom Adjust with the light level control dial 3 Take a photograph To check the mode switch You can check whether the settings of the mode switch are correct by shooting the strobe with a digital camera The number of times a digital camera s built in flash will fire
3. sand and hair Check the O ring to make sure that there is no dust sand or hair on the O ring in the O ring s grooves or on the O ring s contact surfaces If any of these things are attached remove them completely If used as is these things could cause flooding Precautions on Handling the O ring Coat with silicone grease Silicone grease protects the O ring from chafing After checking the O ring to make sure that there are no scratches dust or debris apply a light coating of silicone grease to the entire O ring with your finger Applying too much grease will make it easier for dust and debris to adhere to the O ring and could cause flooding Do not twist the O ring When fitting the O ring into the O ring groove insert it straight into the groove do not bend or twist it Remove the O ring for inspection before each use In principle the O ring should be removed before each use so that the O ring O ring groove and O ring contact surfaces can be checked This is because you cannot find any sand or debris that may have gotten into the O ring groove if the O ring is not removed For routine maintenance prior to each use it is advisable to make sure to remove the O ring Be careful about how you store O rings When storing spare O rings or O rings that you have removed from the housing keep them in a cool place out of direct sunlight Also when storing O rings do not place hea
4. sensitivity and or distance the YS 03 further from the subject When images are overexposed turn off underwater light if used with the strobe E 27 Customize Mode If you change the response to pre flash of the camera in the customization mode the camera in which the flash does not normally emit light in the factory default settings the flash will be able to emit light 4 DS TTL mode ll Start of the Customize Mode Check the OFF position of the 1 Mode 9witch adjust the position of the light level control dial to GN5 6 Press and hold the target light button to turn on mode 4 by turning the mode 3 switch Mode switch characters emission to white Customize Mode is started Release the target light button OQ A CD N When it entered the customize mode to stand for 5 minutes without doing anything it will flash mode set by the mode switch I Set of Pre Flash Cancel Mode 7 To match the mode you want to 1 set turn the light level control dial 2 Press the target light button to set the mode 3 Buzzer sounds READY TTL lamp is turned in green in the setting is completed Light Level Control Dial and Pre Flash Mode Change the light intensity adjustment MANUAL Position Mode dial to position the table on the right it A Factory default will be changed by pressing the target light button on the mode of the right table fl End of the Customize Mode 1T Turn the mode swit
5. The two types of diffusers are attached in the same way Diffuse 100 GN 24 at full flash Beam angle 100 x100 Diffuse 120 GN 20 at full flash Beam angle 120 x120 1 Attach the included diffuser strap to the strap eyelets on the diffuser and the strobe 2 Line up the circular hole on the diffuser with the position on the target light and push the tabs on the diffuser into the grooves one on the left and one on the right on the strobe until they RA l Grooves left and right side cAuTION Always make sure that the diffuser is properly attached before use If not properly attached it may fall off get lost or become damaged E 26 Taking Photographs Detaching 1 Remove by extruding the left or right of the tab on the diffuser in front Remain one side is out you can remove it extruding the opposite side of the tab in front I Using the Red Filter Light of the target light turns red when attaching a red filter on diffuser Attaching Detaching From the strobe mounting surface of the diffuser in a round hole in the diffuser install push to match the red filter Red filter will directed the flange to strobe mounting surface side 2 To disconnecting the red filter and remove push from the character side of the diffuser f Note To prevent overexposure in bright environments with a lot of ambient light adjust the camera s exposure compensation lower the camera s ISO
6. a sync cord When 30 minutes has passed from turning on the power or last emission of the strobe the power will turn off automatically auto power off When turning on the power again set the mode switch to OFF before setting the desired mode ein TTL mode mode statuses set at the time of power off are saved and therefore if the power is turned off while the unit is set to SLAVE TTL mode the unit will start up in SLAVE TTL mode at next power up Light level control dial Light amount can be adjusted in 11 increments GN 1 1 4 2 28 4 5 6 8 11 16 22 32 when the mode switch is set to n or Em Light amount can be checked at the pointer position If the mode switch is set to DS TTL anda fiber optic cable is connected in DS TTL II mode EV compensation is performed CAUTION When the strobe is connected to a SLR housing with a sync cord and the mode switch is set to DS TTL normal TTL mode is activated and you cannot adjust the EV compensation Target light switch The target light turns on Full power when you push the target light switch The target light turns on Low power when you push the switch once again The target light turns off when you push the switch once again Yee ee The target light turns off when the strobe fires and lights rAB up again after 0 5 second Press the button and hold it down for 3 seconds in DS TTL mode to switch to SLAVE TTL mode CAUTION The target light conti
7. differs depending on the shooting mode If you change the shooting mode of the camera check the setting of the mode switch again for that mode 7 Set the camera s built in flash to the forced flash mode and mount the camera to the housing Then connect the housing and this product together with a fiber optic cable 2 Set the mode switch to 4m and the light level control dial to 32 point the digital camera at the front of the strobe and shoot an image The built in flash of the camera must flash 3 Check the image captured by the camera If you see a white flash in the strobe or an image that is completely white then the strobe has fired and the setting is correct If the light emitting part is dark change the mode of pre emission corresponding customize mode the product is taken from the light emitting portion front again check the image P E 28 Taking Photographs DS TTL II mode photography The DS TTL II system included as a feature of the unit is a SLAVE TTL system that is equipped with a compensation function It is effective for use with a main strobe that has a pre flash function such as when there is a built in TTL flash on the camera and another strobe connected to the camera by TTL or Optical YS Converter Please confirm a support model Please refer to our website http www seaandsea jp Compatibility list for the strobe and digital cameras for the support model of the camera 1 Set t
8. left side as seen from the front of the housing however by changing the direction of attachment of the YS Mount Strobe Adaptor you can also attach it from the right side When attaching the YS Mount Strobe Adaptor always refer to YS Mount Strobe Adaptor Ball Mount Strobe Adaptor P E 15 for details CAUTION Please be careful when attaching the YS Mount Strobe Adaptor as inserting the fixing bolt from the side that does not have a nut inserted may lead to it or other parts becoming damaged Do not tighten the fixing bolt up on the product unless it is being attached to an arm Remove the fixing bolt from the product when storing Preparation for Setting Up il Maintaining the O ring This product is kept watertight by the O ring To keep the O ring functioning properly please observe the following before setting up Make sure to remove the O ring when maintaining For detailed O ring maintenance methods please see the O ring maintenance manual CAUTION Make sure to fit install the O ring into the groove properly after maintenance Installing the Batteries Be careful when opening the strobe battery compartment Remove the battery cap in a horizontal position to prevent water drops from entering the battery compartment This model can be powered by the following batteries Use four of each type A AA alkaline battery AA Ni MH battery 7 Make sure that the mode
9. not use the product for an extended period of time periodic maintenance will keep internal electronic parts from deterioration Once a month install batteries and fire a test flash light on Operate all other switches as you would in normal operation Turn the power off then remove batteries while the READY TTL lamp is on for the strobe SEA amp SEA SUNPAK Co Ltd assumes no liability for compensation of loss of captured images or expenses caused by loss of images even if you are unable to shoot due to a product defect or malfunction SEA amp SEA SUNPAK Co Ltd will not be responsible for the replacement or compensation for cameras lenses or those accessories damaged due to your invalid operation Carefully observe the O ring maintenance manual for the handling of O rings before use SEA amp SEA SUNPAK Co Ltd assumes no liability for errors or discrepancies in this manual Specifications and appearance are subject to change without notice The silicon grease included in the product package is inedible E 5 Safety Precautions for Use of Battery N DANGER Never expose the battery to flame or fire or to excessive heat Never attempt to disassemble alter or directly solder the battery There are no user serviceable parts Tampering with battery may expose you to dangerous voltage battery acid or electrical shock Never short circuit the terminals of a battery as it could result in battery leakage heat g
10. specifications were tested at normal room temperature 25 C 77 F Underwater weight measurements have been taken in fresh water Sea water weight will vary E 33 S AcSEA SEA amp SEA SUNPAK Co Ltd T 145 0062 1 4 6 o a okyo Japan 145 eee TEL 81 3 5701 5533 World Customer Service Center TEL 048 255 8512 TEL 81 48 255 8512 http www seaandsea co jp http www seaandsea jp KAJ1426 2015 4 Current as of Apr 2015
11. switch is in the OFF position Turn mark counterclockwise to the OPEN position 3 Pull the battery cap straight out When open a battery cap always pull battery caps sideways 4 Insert four batteries with the polarity shown in the battery compartment E 17 Installing the Batteries 5 Verify that the mark on the battery cap is lined up with the V mark 6 Align the battery cap with the OPEN position and insert the battery cap into the strobe Check the O ring to make sure there are no scratches or debris Turn mark clockwise to the LOCK position Turn until you hear the sound of it clicking into place CAUTION Replace the batteries when it takes 30 seconds or more until the READY TTL lamp illuminates after firing at full When installing or removing batteries thoroughly wipe water off the strobe and dry your hands Pay particular attention not to allow water from your hair or wetsuit to drip into the battery compartment This is in order to prevent an electrical hazard mold malfunction or damage to the strobe Never mix old and new batteries or batteries of different types Always replace all batteries with new batteries at the same time E 18 Connecting the Strobe Setting and cords used to connect to this model can vary depending on the camera housing model The various connection methods using different cords are described here Refer to Taking Photographs
12. the convex part on the MM strobe s connector with the notch of the sync cord s connector and then push it straight in 4 Align with the screws of the strobe and then rotate it until it onvex part Concave part stops Tighten it securely When removing the sync cord loosen and while holding the base of the sync cord s connector pull the sync cord straight out Do not pull the cord 5 Remove the housing s bulkhead connector cap 6 Align the round mark on the sync cord or the notch of the tip and the round mark on the strobe bulkhead or the convex part on the inside and then push it straight in Align the B part of the sync cord with the screws of the strobe bulkhead and then rotate it until it stops 8 Rotate the C part of the sync cord until it stops Tighten it securely When removing the sync cord loosen C first then B and then pull the sync cord straight out holding onto A Do not pull on the cord part Z CAUTION Do not touch the terminal with fingers Do not apply silicone grease to the connector s contact pins If contaminated accidentally clean the pins by a cotton swab moistened with alcohol Whenever a sync cord is not connected protect the connectors with the connector caps Before rinsing a detached sync cord be sure to put the connector caps on the exposed ends Refer to the sync cord instruction manual before use E 20 Connecting the Strobe ii Co
13. ON When you shoot with a digital camera set the built in flash of the camera to the forced flash mode The strobe will not fire unless the built in flash of the camera fires Refer to the digital camera instruction manual for setting the forced flash mode Refer to the fiber optic cable instruction manual before use Refer to the housing instruction manual before use Fiber optic cable socket for additional strobe The fiber optic cable socket for additional strobe is not a slave sensor When using this strobe as a main strobe etc another strobe can be added using a fiber optic cable E 22 Taking Photographs CAUTION elf the full flash has been activated 10 times in a row allow the product to rest for 10 minutes before attempting to use it again Do not attempt to activate the flash on the unit with the flash facing downward Do not look directly into the flash on the unit i Using the Sync Cord Manual photography Light amount of the strobe can be adjusted with the light level control dial 1 Set the mode switch to 4 or eu 2 Adjust with the light level control dial 3 Take a photograph TTL photography Shooting with TTL flash output 1 Set the mode switch to DS TTL 2 Take a photograph CAUTION Requires a SEA amp SEAYS converter Refer to your digital SLR housing instruction manual for details
14. SEAcSEA sa UNDERWATER STROBE Instruction Manual Introduction Thank you for purchasing SEA amp SEA products Please read this instruction manual carefully prior to using your underwater strobe Only with a thorough understanding of this manual s content will you be able to use the strobe correctly After reading the manual please be sure to keep it in a place where you can easily come back to it at any time This products have passed SEA amp SEASs criteria based inspection for pressure resistance FC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference 2 this device must accept any interference received including interference that cause undesired operation ps The product conforms to WEEE standards This symbol indicates separate collection of waste electrical and electronic equipment in the EU countries Please do not throw the equipment into the domestic refuse Please contact your local authorities for recycling program information The appearance of color evenness or weld lines on the external body of the product is normal and will not affect its performance This Class B digital apparatus complies with Canadian ICES 003 CAN ICES 3 B NMB 3 B E 1 Safety 0 219111910 E 3 Safety Precautions for Use of Battery pp E 6 Precautions on Handling the O ring pp E 8 Acce
15. be light towards a driver of a vehicle to avoid causing accidents Do not operate the product while driving a vehicle Inattention could result in accidents For use on land do not operate the product at precarious foothold It may cause falling injury or product damage Do not leave the product on a slope or an unstable surface It may be broken after falling or injure someone below it Keep out of reach of children to prevent accidental ingestion If swallowed seek medical advice immediately CAUTION Read the instruction manual and observe proper precautions before use of this product This product has been designed and manufactured for use at a water depth within 100m 330ft Please note that diving to a depth in excess of 100m 330ft may cause damage to the product or may lead to water leakage Should you notice smoke or unusual smell coming from the product turn it off and remove the batteries immediately taking care to avoid burns Continued operation could result in injury After removing the battery take the product to a SEA amp SEA authorized service center for inspection Discontinue use and turn the product off immediately should you notice flooding or leakage When the product is flooded interior pressure may build up Please be careful the cap may open explosively and cause injuries Do not open the battery cap in the vicinity of open flames The product has been constructed with an airtight
16. ch to the power to OFF 2 End of the customize mode E 28 Customize mode F Mode value Mode value of the pre flash cancellation of typical camera will be the following values Current as of Apr 2015 Other camera Check the correspondence table to third party camera of our web site http www seaandsea co jp CANON Camera Mode Camera Mode EOS 5D Marklll EOS Kiss Digital X7 E05 70D EOS Kiss Digital X7 EOS 7D Powershot G1X Markl EOS 7D Markl Powershot G7X FUJI FILM Camera Mode A Factory default A Factory default A Factory default NIKON Camera Mode Camera Mode TNikontst TD Nkon1AW1 5 OLYMPUS Camera Mode camem Mede A Factory default A Factory default OMDEM5 Markil Bl PANASONIC Camera LX100 SONY Camera Mode RX 100M2 a 6000 E 29 Tough TG 3 A Factory default A Factory default Maintenance and Storage CAUTION After each use in salt water make sure the battery and connector caps are attached then in a watertight condition soak it sufficiently in fresh water Insufficient soaking causes damage by salt to the product Salty residue may be left on the product where it will crystallize as it evaporates Crystallized salt is hard to dissolve and difficult to be removed once formed and it will result in water leakage After
17. e following Improper handling of the O ring could cause flooding N CAUTION SEA amp SEA products use blue O rings These O rings are impregnated with silicone oil through a special process The lubricating effect of the O ring lasts as long as the silicone oil is gradually seeping out from within For the maintenance of these blue O rings make sure to use genuine SEA amp SEA silicone grease O ring grease for use with the blue O rings that comes in tubes with blue lettering and blue caps If you use silicone grease from other companies or SEA amp SEA s own silicone grease that comes in tubes with black lettering and black caps the grease you apply will be sucked into the blue O rings due to their special characteristics which will result in insufficient grease If this happens even once the O ring will not revert to its normal state and must be replaced elf the grease is insufficient the O ring will not slide and it will become harder to open and close the waterproof parts Because of this it could become impossible to open or close the housing or it could cause flooding so please refrain from using the housing with insufficient grease Are there any scratches or cracks in the O ring Check the O ring to make sure there are no scratches or cracks If there are replace the O ring with a new one immediately When handling the O ring do not use pointed metal objects which could damage the O ring Be careful about dust
18. eneration fire or explosion Avoid contact with all metal objects during transporting and storage When recharging batteries such as nickel metal hydride use a charger designed specifically for them and follow the recharging instructions Recharging with an inappropriate charger may cause battery leakage overheating and explosion Move leaking batteries away from fire or open flames immediately The leaked fluid and its vapor are combustible elf the battery leakage contacts your skin or clothing flush the affected area repeatedly with clean water It may irritate your skin Should it get into your eyes immediately rinse them with plenty of water avoid rubbing and seek medical advice Battery has a specific polarity Never force the battery into the charger or the strobe Always check the and polarity before installation Incorrect orientation may cause permanent battery damage Never connect a battery directly to a plug outlet or car cigarette lighter Z WARNING Keep dry The battery is not waterproof and may malfunction if immersed in water or exposed to high levels of humidity Rusting of the internal mechanism can cause irreparable damage Do not remove and or damage the case of a battery It may cause battery leakage overheating or explosion Do not charge a rechargeable battery beyond the specified charging time it may cause battery leakage fire hazard or explosion Never use batteries should you notice a
19. er optic cable connected properly P E 21 Does the built in flash main strobe on the camera fire P E 24 When there is a sync cord present fiber optic connection is disabled even if there is a fiber optic cable connected to the unit To use the strobe with the fiber optic cable connection remove the sync cord P E 19 E 31 Troubleshooting The strobe emits light in manual photography mode but images are dark Does the firing mode for the built in flash main strobe on the camera match the firing mode on the YS D2 P E 24 Please refer to our website http www seaandsea jp Compatibility list for the strobe and digital cameras P E 25 When photographs are taken in DS TTL II mode the captured images are too bright or too dark Is the fiber optic cable connected properly PIE 21 Is the light level control dial in DS TTL I mode set at compensation PE 13 Please refer to our website http www seaandsea jp Compatibility list for the strobe and digital cameras P E 25 There may not be any effect obtained from compensation with the light level control dial depending on the shooting conditions and camera settings i The power will turn off automatically The auto power off mode is turned on When turning on the power again set the mode switch to LOFF before setting it to the desired mode P E 13 E 32 Specifications Controls Indicator Guide number Beam angle C
20. he mode switch to DS TTL 2 Adjust with the light level control dial 3 Take a photograph CAUTION When you use this strobe connected to a SLR housing with a sync cord DS TTL mode will NOT be activated DS TTL mode is activated only when you are using a camera s built in flash or other TTL strobe connected to the camera or optical YS converters If you are connected to the strobe when the strobe is not pre flash is DS TTL II can not be used When you shoot with a digital camera set the built in flash of the camera to the forced flash mode The strobe will not fire unless the built in flash of the camera fires There may not be any effect obtained from compensation with the light level control dial depending on the shooting conditions and camera settings SLAVE TTL mode photography SLAVE TTL mode detects the flash from the built in flash on the camera and enables the strobe to flash 1 Set the mode switch to DS TTL 2 Press and hold down the target light button for 3 seconds Verify that the TTL lamp is illuminated blue 3 Take a photograph CAUTION EV compensation cannot be performed in SLAVE TTL mode The TTL lamp will not illuminate green even if TTL auto adjustment has been completed FE 25 Taking Photographs Using the Diffuser This product comes with two different diffusers Diffuser 100 Diffuser 120 Please select between the two as needed to meet specific shooting applications
21. ht way P E 17 Did you make sure not to use any old batteries P E 17 Has the battery cap been closed properly P E 17 An internal protective circuit is activated if the product begins emitting light continuously If this occurs turn off the power supply and put a product ina cool place for a while An internal protective circuit is activated if the product is left in an area with high temperature If this occurs put the product in a cool place for a while elf the product emits the FULL emission of light in more than 20 continuous bursts an internal protective circuit will be activated to prevent the reflector in the strobe from overheating and the strobe will be placed in standby mode with the READY TTL lamp lights out for at least 20 seconds If this occurs allow this product to cool naturally for at least ten minutes The target light does not turn on Was the target light button held down for the proper length of time The target light may not turn on if the switch is held down for too short a time Press and hold down the target light switch for one second P E 13 Using the Sync Cord The strobe does not fire Is the sync cord connected properly PE 19 Is there any rust on the metal pins of the connector If there is any rust or damage found please contact the World Customer Service Center or an authorized SEA amp SEA dealer Using the Fiber optic Cable The strobe does not fire els the fib
22. nificant electrical hazard due to the high voltage circuitry in the product Do not heat the product or put it into a fire this could result in explosion or fire Unauthorized disassembling and or modification could result in malfunction or flooding and void product warranty Take the product to a SEA amp SEA authorized service center for repair or inspection Z N WARNING Use only batteries approved for use in this product Do not mix old and new batteries of different types Remove batteries before transport or storage or when you are not going to use the product for an extended period of time to prevent unexpected activation Pay particular attention to opening the battery cap to avoid injury Heat from the batteries may cause pressure buildup inside the battery compartment and could result in cap explosion with unexpected force Prevent water or foreign objects from entering the product Discontinue use and turn it off immediately should you notice flooding or leakage Continuous use could result in complete damage to the product Do not handle batteries with wet hands to prevent shock hazards Do not use the product in the presence of flammable gas as this could result in explosion or fire Do not fire the strobe light with the reflector facing a desk or floor to prevent a fire from occurring Touching the reflector immediately after firing could result in burns E 3 Safety Precautions Do not fire the stro
23. nnecting with the Fiber optic Cable Connect this product with the fiber optic cable option when it is triggered by sensing the light from the camera s built in flash Using a built in slave sensor this strobe is triggered by sensing the light from a digital camera s built in flash If the fiber optic cable is not used DS TTL II modulation cannot be obtained unless a fiber optic cable is used CAUTION Some housings are not compatible with fiber optic cable Be sure to turn off power to the strobe before proceeding 1 Open the sensor cover After using manually move the cover and wash thoroughly with pure water gt Maintenance and Storage P E 30 Insert the fiber optic cable s connector into the fiber optic cable socket slave sensor of the strobe until it stops The second fiber optic socket on the right may be used to fire an additional strobe LD Fiber optic cable socket for additional strobe P E 22 3 Secure the fiber optic cable with the fiber optic cable hook E 21 Fiber optic cable hook Connecting the Strobe 4 Connect the fiber optic cable s connector to the socket in the housing When the fiber optic cable cannot connect directly to a compact digital camera housing no fiber optic cable socket attach the strobe mask A optional to the flash window of the housing and then connect the fiber optic cable B optional CAUTI
24. nserted fixing bolt by changing the orientation for attachment of the YS Mount Strobe Adaptor By replacing it with the included Ball Mount Strobe Adaptor you can select a method for attachment to a housing that matches the shooting conditions How to detach a YS Mount Strobe Adaptor 1 H 1 ow to attach a Ball Mount Strobe Adaptor Remove the two cap bolts used to secure the YS Mount Strobe Adaptor using the included hexagon wrench turned counter clockwise M4 Hexagon Wrench YS Mount Strobe Adaptor M4 Hexagon Wrench Attach the Ball Mount Strobe Adaptor to the camera and lightly secure it using cap bolt the two cap bolts turned clockwise by hand Use the cap bolts screwed into the YS Ball Mount Mount Strobe Adaptor Strobe Adaptor Use the included hexagon wrench to firmly tighten the cap bolts and secure the adaptor to the unit Use the short end as shown in the diagram at right of the hexagon wrench to tighten cap bolts Do not apply excessive force where tightening up the cap bolt E 15 Identification of Parts Fixing Bolt If attaching the unit to an arm or other part insert the fixing bolt from the side of the YS Mount Strobe Adaptor which does not have a nut inserted and tighten to secure Correct YS Mount Strobe Adaptor Fixing Bolt Attaching from the opposite direction At factory shipment the fixing bolt is inserted to be attached from the
25. nues to be illuminated until pushing the switch setting the mode switch to OFF or until the power turns off automatically auto power off The target light will flicker when the batteries get low this is not a malfunction E 13 Identification of Parts I READY TTL lamp READY llluminates when the strobe is ready to fire aL TTL After shooting with TTL automatic light iTAB aa oa control is completed the TTL lamp will ET illuminate in green for approximately 2 READY TTL seconds ae ee Ge Cb renecoago PE we AR PSM TTL automatic light control IIluminates PiE 13 has been completed Green There is no remaining Replace the battery with a new blinks Orange battery power j y P 13 one n Mode There is no remaining Repl h th blinks Green battery power hn Ne PEE P E 13 blinks AU Replace the battery with a new battery power P E 13 Light Blue one DS TTL Mode There is no remaining Repl h h blinks Blue battery power ee DD Nan P E 13 SLAVE TTL TTL Mode l The orange and EE Please contact the World The protective circuit is green lamps Customer Service Center or an P E 3 1 activated flash alternately authorized SEA amp SEA dealer E 14 Identification of Parts i YS Mount Strobe Adaptor Ball Mount Strobe Adaptor A YS Mount Strobe Adaptor is included with this product as standard equipment You can change the orientation for the i
26. ny changes such as leakage discoloration or deformation When you notice the situation as abnormal discontinue use immediately and take the product to a SEA amp SEA authorized service center for inspection Keep out of reach of children to prevent accidental ingestion If swallowed seek medical advice immediately Do not leave or use batteries in an extreme hot environment This may cause battery leakage overheating or battery performance deterioration Do not use non recommended batteries such as lithium primary batteries Use of non recommended batteries may cause battery leakage and overheating and may cause the strobe to rupture which could result in personal injury E 6 Safety Precautions for Use of Battery Z N CAUTION Avoid strong shocks impacts or excess stress to batteries For handling and recharging of a battery refer to the instruction manual of the battery dedicated charger Always recharge the rechargeable battery before use after an extended time of storage Dirt on the battery terminals can prevent the product from functioning Should the battery terminals become dirty wipe them with a clean dry cloth before use Used rechargeable batteries are valuable resource Please recycle used rechargeable batteries in accordance with local regulations Precautions on Handling the O ring This product is kept watertight by the O ring To keep the O ring functioning properly please observe th
27. odes AA Set the mode switch to this position if setting the light amount to Manual When connecting using a fiber optic cable set the mode switch to this position for digital cameras without pre flash modes DS TTL Set the mode switch to this position when shooting with TTL flash output When a fiber optic cable is connected DS TTL I mode is activated You can switch to SLAVE TTL mode by pressing and holding down the target light switch for 3 seconds 2 DS TTL II mode photography PE 24 Pre flash Some of the digital camera it is taken by the flash from performing a dimming in advance flash main flash The flash for this in advance of dimming is called a pre flash Characters Emission Color in Mode The emission color of the character will change the mode Emission color are shown in the table below Fiber Optic cable Orange Green Green T LightBlue sLAVETTL be SS mt Customize mode is used to change the settings corresponding to the pre flash of the camera P E 28 E 12 Blue Identification of Parts CAUTION The number of times a digital camera s built in flash will fire differs among models Depending on the number of pre flashes mode switch settings can differ so check settings before shooting by conducting test flaches amp To check the mode switch P E 23 n and 47 have the completely same performance when the strobe is connected with
28. olor temperature Battery life Recycle time Battey requirements Mode switch OFF m 4m DS TTL Target light switch ON HIGH ON LOW OFF Light level control dial Ready lamp llluminates when the strobe is ready to fire TTL lamp Illuminate in green for approx 2 sec after firing with DS TTL II flash output 32 at full flash ISO100 m 24 with diffuser 100 20 with diffuser 120 80 x80 100 x100 with diffuser 100 120 x120 with diffuser 120 5600 K at full flash land 5250 K with diffuser 100 Alkaline Approx 150 flashes Ni MH eneloop Approx 200 flashes Alkaline Approx 3 0sec Ni MH Approx 1 5sec 4xAA Alkaline 4xAA Ni MH Operating temperature 1 C 40 C 34 F 104 F Construction Depth rating Dimensions WxHxD Weight Weight underwater Accessories Polycarbonate ABS resin 100m 330ft 89x133x116mm 3 5x5 2x4 6inches Approx 623g 22 0oz excl batteries Attached a YS Mount Approx 40g 1 820z incl batteries eine een Diffuser 100 Diffuser 120 Diffuser strap x2 O ring maintenance manual Silicone grease Ball Mount Strobe Adaptor Fixing bolt M4 Hexagon Wrench Spare bolt cap x1 Red Filter x2 Attached accessories to the product YS Mount Strobe Adaptor The specifications and external design are subject to change without notice Number of flashes and recycle time depends on the battery brand temperature and frequency of use The above
29. ot carry the camera or housing by holding the accessories such as arm cable strobe etc Heavy components may fall and cause damage or injury Do not rest heavy weight on the product It might deform the outer casing damage internal parts make the waterproofing fail or result in fire or electric shock Rinse the product with fresh water after underwater use Ensure that the product is watertight before rinsing Refer to Maintenance and Storage for details Make sure that the connectors have been secured with the connector caps before rinsing the product with fresh water after removal from other products Never use chemicals cosmetics any petroleum solvents such as paint thinner or neutral detergent on the product They may deform and damage the product Do not leave the product in places with hot temperatures such as inside of a car or in a car trunk in summer The heat may deform plastic parts of the product damaging internal parts and resulting in potential fire or electric shock If the product is sealed tight in hot conditions heated air expanding inside the product may deform the casing and ruin the watertightness Do not store the product in wet or high humidity place to avoid mold rust corrosion or malfunction Do not store the product with naphthalene or camphor mothballs or in locations such as a laboratory where chemicals are used This environment can cause mold rust corrosion or malfunction elf you do
30. rinsing dry the product well with a soft dry cloth then let the prosuct dry in the shade out of direct sunlight Do not dry the product by heating using a hair dryer for example Heating can deform and damage the product If you do not use the product for an extended period of time store it away from high temperatures high humidity direct sunlight or extreme cold Always remove batteries from the product after use After using the product maintain the O rings before storing Examine the O rings before and after each dive We recommend early exchange of the O rings at least once a year Every two years we recommend a complete overhaul of O rings regardless of the frequency in use for the best performance of the product If you do not use the product for an extended period of time periodic maintenance will keep internal electronic parts from deterioration Once a month install batteries and fire a test flash While the READY TTL lamp is ready to fire set the mode switches to OFF then remove the batteries In addition operate all other swithes as you would in normal operation E 30 Troubleshooting Please confirm the following items If conditions do not improve even after the following has been confirmed please contact the World Customer Service Center or an authorized SEA amp SEA dealer I READY TTL lamp does not light up Do you insert the batteries P E 17 Do you insert the batteries the rig
31. seal When packing the product for airplane travel Please be transported Remove the battery cap Do not open the product in a wet or sandy environment Protect the interior from moisture and debris in order to prevent malfunction or flooding Keep away from strong magnetic fields Do not use or store this product in the vicinity of equipment that generates strong electro magnetic radiation or magnetic fields Strong static charges or the magnetic fields could cause malfunction or affect the product s internal circuitry Before using the product in an airplane or a hospital check if it is allowed Electromagnetic waves emitted by the product may interfere with the measuring instruments or medical equipment Do not cover or wrap the product with a cloth when firing the strobe This could result in deformation of the product or in fire Using the strobe close to your subject s eyes could cause temporary visual impairment Particular care should be observed if photographing infants the strobe should be no less than one meter 3 feet from the subject Safety Precautions Be careful when touching the product immediately after firing repeatedly or lighting for a long time The product may get hot enough to burn you Avoid strong shocks impacts or excess stress to prevent malfunction damage or breakdown Make sure that the product has been securely mounted to other products in order to prevent injury fall or missing Do n
32. ssories Ne E 10 E 11 9 eer ee ae ener me ner en ae ene A E 12 READ YE E 13 YS Mount Strobe Adaptor Ball Mount Strobe Adaptor E 14 Preparation for Setting Up pp E 17 Installing the Batteries pe E 17 Connecting the Strobe Nt E 19 Withthe Syne GON aaa E 19 With the Fiber optic Cable pp E 21 Taking Photographe ee E 23 Using the Sync Cord pp E 23 Using the Fiber optic Cable pp E 24 Using the Diffuser pe E 26 Using the Red E 27 Customize Mode pp E 28 Maintenance and Storage pp E 30 Troubleshooting 0 E 31 ne 0 212 672 6 Beene ae ee ene ee eee eran ee ee a E 32 Safety Precautions SEA amp SEA strobes have been designed for in water use only Limit the strobes use out of water to test firing only For safe handling of the product please read the following precautions carefully before use Failure to heed the precautions listed below could result in serious consequences To prevent injury or damage to yourself and or others please observe the precautions as they contain highly important information related to personal and product safety DANGER _ Situations that involve a high risk of severe injury or death Z N WARNING Situations that could result in severe injury or death CAUTION Situations that could result in property damage or personal injury N DANGER Never attempt to disassemble repair or alter the product yourself to prevent sig
33. vy objects on them or twist them O rings last for one year Although it depends on how well they are maintained how often they are used and how they are stored O rings generally last for one year It is advisable to inspect them before use and replace them early _Accessories Before using this model check to make sure that all accessories are present 2 YS Mount Strobe Adaptor WER es mounted on the YS D2 Silicone Grease Diffuser 120 Fixing Bolt M4 Hexagon Wrench Red Filter x2 Spare cap bolt x1 Diffuser Strap x2 O ring Maintenance Manual YS D2 Instruction Manual this manual Identification of Parts Target light P E 13 Fiber optic cable socket for additional strobe PE 22 WA Ja AN PFiber optic cable hook P E 21 Strap eyelet P E 26 3 Fiber optic cable ste i YS Mount Strobe Adaptor P E 15 Battery cap P E 17 Light level control A A AE dial P E 13 READY TTL lamp P E 14 Fiber optic cable hook Target light P E 21 switch P E 13 Mode switch Fixing bolt P E 13 P E 16 Identification of parts Operation OFF Turns the power off Set the mode switch to OFF when you are not using the strobe A Set the mode switch to this position if setting the light amount to Manual When connecting using a fiber optic cable set the mode switch to this position for digital cameras with pre flash m
Download Pdf Manuals
Related Search