Smart pH Meter - Milwaukee Instruments
Contents
1. H7 MW 100 pH Meter range 0 0 14 0 pH Smart pH Meter OPERATION The meter is supplied complete with a 9V battery Slide off the battery compartment cover on the back of the meter Install the battery into the battery clip connector while observing polarity Always remove the electrode protective cap before taking any measurement If the electrode has been left dry soak the tip bottom 2 5 cm in rinse solution M10000B for a few minutes to reactivate it l M MW 100 pH Meter range 0 0 14 0 pH Connect the pH electrode to the BNC socket on the top of the meter Make sure that the meter has been calibrated before taking any measurements see Calibration Procedure Immerse the tip 2 5 cm of the pH electrode into the sample Turn the instrument on by pressing the ON OFF key Allow the reading to stabilize before taking measurements After measurements switch the meter off and store the electrode with a few drops of storage solution MA9015 in the protective cap CALIBRATION PROCEDURE Remove the protective cap from the electrode Rinse tip off with distilled water or a small quantity of pH 7 Immerse the electrode tip into a new sachet of pH7 calibration solution and allow the reading to stabilize CAL S B LU TION ION RH e Adjust the pH7 OFFSET calibration tr2. SPECIFICATIONS AW Milwaukee MW100 RANGE 0 0 to 14 0 pH RESOLUTION 0 1 pH ACCURACY 25 C 0 2 pH TYPICAL EMC DEVIATION 0 1 pH pH ELECTRODE MA911B 1 included ENVIRONMENT 0 to 50 C 95 RH max BATTERY TYPE 1 x 9V alkaline included BATTERY LIFE approximately 300 hours of use DIMENSIONS 143 x 80 x 32 mm WEIGHT 220 g with battery meter only OPTIONAL ACCESSORIES M10004B pH 4 01 buffer solution 20 mL sachet 25 pcs M10007B pH 7 01 buffer solution 20 mL sachet 25 pcs M10010B pH 10 01 buffer solution 20 mL sachet 25 pcs M10000B Electrode rinse solution 20 mL sachet 25 pcs MA9015 Electrode storage solution 220 mL bottle MA911B 1 pH electrode with BNC connector and 1 m cable MA950 Portable meter wall mounting kit WARRANTY This instrument is warranted from all defects in materials and manufacturing for a period of two years from the date of purchase The electrode is warranted for a period of six months If during this period the repair or replacement of parts is required where the damage is not due to negligence or erroneous operation by the user please return the parts to either dealer or our office and the repair will be effected free of charge Note We reserve the right to modify the design construction and appearance of our products without advance notice ONLO OOLMWLSI NN Milwaukee USER MANUAL PORTABLE pH METER MODEL MW100 Smart p Meter Calibration pH4 10 p
3. immer MV Miwaukee to display 7 0 pH e Open a new sachet of pH4 calibration solution and use a small quantity to rinse the electrode oe e Immerse the electrode tip inside the pH4 o mg sachet and allow the reading to stabilize prano ou e Adjust the pH4 pH10 SLOPE calibration trimmer to read 4 0 pH range 0 0 14 0 pH e The calibration is now complete and the meter is ready to take measurements e It is suggested the meter be calibrated at least once a month after a prolonged period of inactivity and after electrode replacement BATTERY REPLACEMENT When the battery becomes weak the meter will display 63 When the low battery indicator appears the battery has only about 50 hours of working time left A low battery will result in unreliable measurements Prompt battery replacement is required Battery replacement must only take place in a non hazardous area using an alkaline 9V battery Turn the meter off slide the battery compartment cover located at the rear of the meter off and replace the 9V I battery with a new one Make sure the battery contacts are fully engaged in the connector seat the battery in its compartment and replace the cover Ifi Rocky Mount NC USA MADE IN EUROPE ROMANIA Milwaukee x
Download Pdf Manuals
Related Search