Quick Reference Guide
Contents
1. KANE499 Quick Reference Guide a Infra red emitter and torch light Menu controls Scroll up down Enter Function buttons x 4 See below for details Rotary switch i Particle filter Water trap Battery charging indicator Analyser Connections Flue Gas Inlet see diagram overleaf see diagram overleaf ON OFF BACKLIGHT _ Turns the analyser ON OFF Switches backlight amp torch light ON OFF SEND ENTER _ Send readings to printer Press button for 1 second _ Send readings to memory Hold button down for 2 secs Stock No 18839 July 2011 PUMP lt Turns the pump ON OFF Hold button to zero pressure O Kane International Ltd connection Flue Gas Inlet Rubber Bung Flue probe E T1 Baley charger Pressure connection P1 Pressure connection P2 differential 1 BEFORE USING ANALYSER CHECK THE FOLLOWING Particle filter is not dirty inside Water trap and flue probe hose are empty of water Water trap and rubber bung are fitted correctly to the analyser Flue probe hose is connected properly to the flue gas inlet Flue probe temperature plug is connected into T1 temperature connection Please read the Safety Warnings in the User Manual 2 FRESH AIR PURGE Position the flue probe in fresh air then press the On Off button The analyser auto calibrates for approximately 90 seconds When complete Select Ratio on the dial In fresh air2. a full combustion report O2 EFF display 02 5 4 Oxygen left after combustion Should be 20 9 in fresh air TFc 55 1 Flue temperature C Te 17 2 Inlet temperature Normally set by flue probe during fresh air purge EfC 98 3 Condensing boiler efficiency EfC Can be changed via Menu Press SEND to print a full combustion test Also sends to PC if Bluetooth fitted Hold SEND for 2 seconds to log a full combustion report AUX display 02 20 9 The default AUX auxiliary display is shown COP 00 The parameters on lines 1 2 3 and 4 can be set independently 11 55 02 To customise the AUX display select MENU SCREEN AUX BAT 59 They remain the AUX parameters until changed again by the user Press SEND to print a full combustion test Also sends to PC if Bluetooth fitted Hold SEND for 2 seconds to log a full combustion report PRESSURE TEST Also see section 9 Select Prs The pump stops Press the PUMP button to auto zero the pressure sensor Using the black connectors and manometer hose connect to P1 for single pressure or P1 and P2 for differential pressure PRS display PRESSURE Defaults to smoothing off on start up Can be changed via Menu P 0 04 Defaults to low resolution on start up Can be changed via Menu mbar Pressure units can be changed via Menu 12 56 29 Displays time to enable manually timed tests Press SEND to print a pres
3. 33 Pressure at start of tightness test P2 20 26 Pressure at end of tightness test PRINT Y The test can be printed immediately or later from the memory The analyser s memory can store up to 20 tightness tests Tightness tests are logged automatically therefore the tightness section of the memory will be full after the 20 tightness test is complete Before the 217 tightness test can be performed the tightness section of the memory must be cleared To do this select MENU REPORT TIGHTN S DEL ALL YES then press lt p DIFFERENTIAL TEMPERATURE Select Diff Temp to measure flow return and differential temperatures DIFF TEMP display TEMP Pump automatically switches off when dial is moved to Diff Temp T1c 60 1 Use the T1 connection for the flow temperature sensor T2c 47 0 Use the T2 connection for the return temperature sensor IES VE 13 1 Real time temperature difference Press SEND to print a differential temperature test Also sends to PC if Bluetooth fitted Hold SEND for 2 seconds to log a differential temperature report 10 ROOM CO TESTING Select Room CO for CO investigations Please refer to user manual ROOM CO display ROOM CO Duration of this test is variable from 0 to 30 minutes as per BS7967 COP 00 Real time CO reading ppm TEST 14 Test 00 start To stop the Room CO test press the PUMP button LOG 01 The complete Room CO test is automatically stored as a log nu
4. 8 Z My Customer Appliance Ref K455 1 0 YOUR COMPANY NAME amp PHONE NUMBER HERE DIFF TEMP LOG as TIME 12 18 15705708 66 1 47 8 Appliance Ref K4 gt gt 1 0 YOUR COMPANY NAME 2 PHONE NUMBER HERE ROOM CO TEST HI 12 58 15705708 LOG TIME TEST N 0 Pr 10 00 y Ol 09 P HA E XIMUM CO 11 ZZ pa pue pue pd pd pus D Customer Appliance Thank you for reading this data sheet For pricing or for further information please contact us at our UK Office using the details below SUR steel UK Office Keison Products P O Box 2124 Chelmsford Essex CM1 3UP England Tel 44 0 1245 600560 Fax 44 0 1245 808399 Email sales keison co uk Please note Product designs and specifications are subject to change without notice The user is responsible for determining the suitability of this product
5. O PRESSURE Stored pressure tests VIEW DEL ALL or EXIT max 20 tests MA TIGHTN S Stored let by and tightness tests VIEW DEL ALL or EXIT 20 tests Fc TEMP Stored differential temperature tests VIEW DEL ALL or EXIT 20 tests MN ROOM CO Stored room CO tests VIEW DEL ALL or EXIT max 20 tests SCREEN CONTRAST CONTRAST Factory setting is 04 setting is Factory setting is 04 Enables users to customise the parameters on the AUX display User can set any parameter on lines 1 2 3 and 4 HEADER Sets printout header 2 lines 20 characters per line SERVICE CODE Password protected for authorised service agents Leave set to 0000 To EXIT EACH Sub MENU select EXIT To EXIT the MENU move the rotary switch to any position other than Menu Any changes that have not been entered will be ignored 12 Printouts bk AG 1 YOUR COMPANY NAME amp PHONE NUMBER HERE TEST 19 DATE 15 85 98 TIME 12 98 05 COMBUSTION NAT GAS EFF CC LOSSES XAIR CO COe PRS mBAR 4 2081 MH Mu Customer Appliance Ref Rass 1 0 YOUR COMPANY NAME amp PHONE NUMBER HERE PRESSURE OG a4 TIME 12 56 15705708 PRS MBAR 6 20 Customer Appliance Ref K455 ien O YOUR COMPANY NAME amp PHONE NUMBER HERE LUG TIME Let By Test PRS_i MBAR PRS_ amp MBAR LET BY MINS Tightness Test O Tee PR5_i mBAR PRS_2 MBAR 4PR5 mBAR STABIL N MINS TIGHTN S MINS ud 11 53 1570570
6. mber OTHER DISPLAY CODES PO Pump Off OC Open Circuit on temperature input FOR BEST PRESSURE SENSOR ACCURACY 1 Switch the analyser on for 5 minutes to let the temperature stabilise 2 Zero the pressure sensor when the analyser in the exact position that it will be used TO FULLY CHARGE NIMH RECHARGEABLE BATTERIES 1 The analyser must be switched on 2 Connect the charger and switched it on charging indicator illuminates 3 Switch the analyser off the display will show BATTERY CHARGING 4 The BAT status number of fully charged NiMH batteries is typically 70 11 USING THE MENU Select Menu on the rotary switch and navigate using the function buttons er o Soroll down SETUP SET FUEL o L OIL 28 35 sec PROPANE BUTANE LPG PELLETS MN Nec gt 6 EfN nett efficiency EfG gross efficiency EfC condensing efficiency MI SET TIME Uses Military time 7am 07 00 7pm 19 00 a SET DATE Uses DD MM YY format PRESSURE SMOOTH OFF normal response ON slower damped response RESOLVE LOW normal HIGH displays to an extra decimal place Sy PS UNITS mbar mmH O Pa kPa PSI mmHg hPa InH2O LET BY Set duration of let by test in minutes Default 1 minute TIMES STABIL N Set duration of stabilisation in minutes Default 1 minute TIGHTN S Set duration of tightness test in minutes Default 2 minute REPORT COMB N Stored combustion tests VIEW DEL ALL or EXIT max 99 tests M
7. sure test Also sends to PC if Bluetooth fitted Hold SEND for 2 seconds to log a pressure report LET BY and TIGHTNESS TESTING Also see section 9 Select Tightness The pump stops Press the PUMP button to auto zero the pressure sensor Select yes or no for the let by test by using A or V then press Connect from the test point to P1 using a black connector and manometer hose Adjust the gas pressure as you would with a U tube manometer Press ge to start either the let by test or the stabilisation period LET BY Let by test display P1 10 35 Pressure at the start of the let by test P2 10 35 Real time pressure reading TIME 59 Let by default time is 1 minute Can be changed via Menu Note When complete adjust the gas pressure if necessary then press g to start the stabilisation period STABIL N Stabilisation display P1 20 00 Real time pressure reading mbar TIME 59 Stabilisation default time is 1 minute Can be changed via Menu When complete adjust the gas pressure if necessary then press g to start the tightness test TIGHTN S Tightness test display RI 20 33 Pressure at start of tightness test P2 20 33 Real time pressure reading TIME 119 Tightness default time is 2 minute Can be changed via Menu When complete the display will show LOG 06 Let by and tightness test are automatically stored as a log number P1 20
8. the CO reading Oppm Select O2 Eff on the dial In fresh air the O reading 20 9 Select Status on the dial to view the following STATUS display BAT 59 Battery status If less than 20 recharge or replace see section 10 11 46 29 Current time Can be set via the Menu see section 11 15 05 08 Current date Can be set via the Menu see section 11 CAL 283 Number of days until next check and calibration is required Note Boiler inlet air temperature can either be a Set automatically by the flue probe during the fresh air purge or bb Continuously measured if a thermocouple is plugged into the T2 socket 3 COMBUSTION TESTS Select Ratio on the dial to check that the analyser is set for the correct fuel To change fuel select MENU SETUP SET FUEL then use scroll and enter see section 11 Position the flue probe as per the boiler manufacturer s instructions typically the tip of the flue probe is inserted to the centre of the flue The readings will stabilise after 60 seconds assuming the boiler conditions are stable The rotary switch can be used to display the following information RATIO display NAT GAS Fuel type can be changed via Menu see section 11 R 0 0001 CO COz ratio COP 12 Carbon Monoxide ppm CO2 8 8 Carbon Dioxide Press SEND to print a full combustion test Also sends to PC if Bluetooth fitted Hold SEND for 2 seconds to log
Download Pdf Manuals
Related Search