Quick Draw Electronics Shooting Sports Timer User Manual Model
Contents
1. 3 Quick Draw Electronics Shooting Sports Timer User Manual Model TS1000 Rev B Sept 2008 WELCOME TO THE QUICKDRAW ELECTRONICS SHOOTING SPORT TIMER THE BASIC SYSTEM TS1000 0001 1001 CONSISTS OF 2 SOUND SENSORS 2 LIGHT ASSEMBLIES 1 TIMER BOX 2 TIMER TO LIGHT CABLES 2 SENSOR TO LIGHT CABLES 1 PUSHBUTTON 1 POWER CORD THE TS1000 0001 1002 SYSTEM INCLUDES 2 TARGET ASSEMBLIES ALONG WITH THE COMPLETE TS1000 0001 1001 SYSTEM SETUP Single Timer Setup AC Power Supply AC Power Supply Dual Timer Setup SET UP IS QUICK AND EASY START BY ATTACHING A SOUND SENSOR AND A LIGHT ASSEMBLY TO THE BACK OF EACH TARGET MAKE SURE THE LIGHTS ARE CLEARLY CENTERED ON THE TARGET WINDOW PLUG IN THE SENSOR TO LIGHT CABLE TO EACH UNIT PLUG ONE END OF THE LIGHT TO TIMER CABLE INTO THE LIGHT BOX PLUG IN THE OTHER END TO THE BACK OF THE TIMER BOX PLUG IN THE PUSHBUTTON JACK TO THE BACK OF THE TIMER BOX PLUG IN THE POWER CORD TO THE POWER JACK ON THE BACK OF THE TIMER BOX PLUG INTO POWER SOURCE YOU ARE READY TO START MODES NORMAL MODE WHEN THE UNIT IS PLUGGED IN IT WILL GO THROUGH A SELF TEST PROCESS THE DIGITAL DISPLAY WILL RUN UNTIL IT REACHES 9 999 DURING THIS CYCLE TIME THE LIGHT BOXES WILL BE CONSTANTLY LIT WHEN THE CYCLE IS COMPLETE THE LIGHTS WILL FLASH BRIEFLY AND THEN GO OUT AT THIS POINT THE SYSTEM IS READY TO START THE TIMER RANDOM DELAY PRESS THE PUSHBUTTON AND RELEASE THE DISPLAY WILL RE2. connects up to four timers together ww 5 LL Hand Switch Remo Sur LL L B B T S alloon Switch long handle gold contacts e Shoot Timer Replacement Impact Sensors 40 50 20 30 30 6 30 20 40 52 21
3. AD 0 000 WHEN THE LIGHT ILLUMINATES THE TIMER STARTS A HIT ON THE TARGET WILL STOP THE TIMER IF YOU ARE SHOOTING WITH A SINGLE TARGET A HIT WILL CAUSE YOUR LIGHT TO GO OUT IF YOUR ARE SHOOTING WITH TWO TARGETS THE WINNING TARGET LIGHT WILL FLASH TO RESTART SYSTEM PRESS PUSHBUTTON PRACTICE MODE TO TOGGLE TO THE PRACTICE MODE HOLD THE PUSHBUTTON DOWN FOR 12 SECONDS THE DISPLAY WILL READ PPPP A DELAY BEGINS THE SYSTEM WILL THEN SOUND A BEEP THIS WOULD BE THE SHOOTER SET SIGNAL AFTER A RANDOM DELAY THE LIGHT WILL ILLUMINATE AND THE TIMER WILL BEGIN A HIT ON THE TARGET WILL STOP THE TIMER OTHERWISE THE TIMER WILL RUN TO 9 999 AND START THE CYCLY OVER AGAIN THE RECYCLE DELAY DEPENDES ON THE NUMBER OF LIGHTS PLUGGED INTO THE TIMER IF BOTH LIGHTS ARE PLUGGED IN THE TIMER WAITS 16 SECONDS AND THEN RESTARTS THE CYCLE IF ONE LIGHT IS PLUGGED IN THEN THE TIMER WAITS 4 SECONDS BEFORE STARTING THE CYCLE TO EXIT PRACTICE MODE AND GO TO SLAVE MODE PRESS THE PUSHBUTTON FOR 12 SECONDS UNTIL DISPLAY READS SSSS COMPETITION MODE TO TOGGLE TO THE COMPETITION MODE HOLD THE PUSHBUTTON DOWN FOR 12 SECONDS WHEN IN THE PRACTICE MODE THE DISPLAY WILL READ SSSS WHEN IN THE COMPETITION MODE THE TIMER WILL TURN ON THE LIGHTS AND START THE TIMER EXACTLY 2 SECONDS AFTER THE RELEASE OF THE REMOTE SWITCH THE USER DETERMINES THE RANDOM DELAY TIME BY WAITING TO RELEASE THE REMOTE BUTTON THE USER CAN CONCEAL THE REMOTE SWITCH FRO
4. M THE SHOOTERS SO THAT THEY CAN NOT ANTICIPATE THE LIGHT ON EVENT A HIT ON THE TARGET WILL STOP THE TIMER IF YOU ARE SHOOTING WITH A SINGLE TARGET A HIT WILL CAUSE YOUR LIGHT TO GO OUT IF YOU ARE SHOOTING WITH TWO TARGETS THE WINNING TARGET LIGHT WILL FLASH THIS MODEIS INTENDED TO ALLOW MULTIPLE TIMERS TO BE SLAVED TOGETHER AN OPTIONAL COMPETITION CONTROLLER IS AVAILABLE TO AUTOMATE THE RANDOM PUSH BUTTON TO EXIT COMPETITION MODE AND RETURN TO NORMAL MODE PRESS THE PUSHBUTTON FOR 12 SECONDS UNTIL DISPLAY READS 0 000 Competition Controller Slave Mode Cable C Power Supply Dual Timer Setup with Competition Controller BALLOON SWITCH OPERATION WHEN THE TIMER IS USED WITH A BALLOON SWITCH THE USER INSTALLS A BALLOON IN THE BALLOON TARGET AND THEN PRESSES THE START BUTTON IF TWO BALLOON TARGETS ARE USED THE WINNERS LIGHT WILL FLASH A NEW BALLOON MUST BE INSTALLED IN THE BALLOON TARGET AFTER EACH SHOT IF A BALLOON IS NOT PRESENT THE TIMER ASSUMES THAT THE TARGET IS NOT PRESENT AND WILL NOT FLASH THE LIGHTS DECLARING A WINNER THE BURSTING OF THE BALLOON SIGNALS THE TIMER TO STOP THE TIME OPTIONAL EQUIPMENT THE OPTIONAL FOOT SWITCH MAY BE PLUGGED INTO THE TIMER BOX IN LIEU OF THE PUSHBUTTON THE OPTIONAL DC POWER CABLE MAY BE USED WITH AN AUXILLARY POWER UNIT OR BATTERY Options Extras and Spares Cash Check or Money Order Discount Price Credit Card Debit Cards or Paypal Price lave mode cable set
Download Pdf Manuals
Related Search