L4685 - myHomeVillage.com
Contents
1. Local display Description LOCAL DISPLAY is an OLED Touch Screen technology control and management DEVICE FOR The scenario control temperature control and sound system functions of the MY HOME system Integration with the device is simple and intuitive when the display is touched a click is emitted through the internal loudspeaker and the display comes on for 30 seconds if the display is OFF or a screensaver is playing the first touch will cause the display to activate without sending any controls If the display is already active the corresponding icon becomes coloured while pressed and the associate control is performed On the lower section of Local Display is a serial connector for connection of the device to a PC using the USB 3559 programming accessory for updating the configuration the set of characters and icons and the firmware Technical data Power supply from BUS 27 Vdc Operating power supply with SCS BUS 18 27 Vdc Stand by Absorption 20 mA max Operating absorption 60 mA max Operating temperature 5 35 C Size 2 flush mounted modules Legend 1 OLED technology Touch Screen 2 Configurator socket 3 BUS clamp 4 Clamp for the connection of the external temperature probe 5 Serial connector Configuration Local Display may be configured in two ways physical configuration by connecting the configurators to the appropriate sockets The configurators can on2. arting from 1 To recall an existing scenario a quick pressure of the corresponding key on the display is enough NOTE Once the necessary operations have been completed block programming by pressing the lock unlock key of the scenario module for at least 0 5 seconds until the corresponding LED turns red To delete a scenario proceed as follows 1 the scenario module must be enabled for programming 2 press the pushbutton for the scenario to be cancelled for at least 10 seconds The display will confirm that the scenario has been deleted and return to the main screen To reset the whole memory from the scenario module press the DEL key for 10 seconds The yellow LED reset scenarios will flash quickly HD4685 HC4685 HS4685 L4685 N4685 NT4685 0 9 room of the scenario module item F420 1 9 light point of the scenario module item F420 0 8 scenario number 3 scenario 1 scenario 2 scenario 3 scenario 4 NOLLWWOLNY SLIJHS TVDINHD3L N 9 6LO0L4 N 9 6 LOOLE Sound system control mode FUN 2 With this mode for the associated amplifier the user can control the switching ON or OFF the volume the cycling through the sources and their management where allowed Information on the currently active source is also displayed In this mode the parameters that can be configured are the local address of the display which must coincide with the A Pf address and the M1 mode
3. erating mode Measured temperature Decrease temperature 9 Operating mode indication 10 System status indication 11 Increase the temperature 2S eS a Se HD4685 HC4685 HS4685 L4685 N4685 NT4685 Temperature probe BUS SCS 0 9 Local Display address 1 9 Local Display address 0 8 Slave probe number 3 For more complex systems the probe can memorize the actuators to activate and the pumps to control on the BUS The programming operation must be completed directly from the central unit The central unit can also be used for the calibration of the probe During the system setting stage it will be necessary to specify the actuators used for the heating system and those used for the air conditioning system as they operate in a complementary way 11 2 3 10 4 9 5 8 6 NOILVWOLNY SLAAHS IWDINHDAL N 9 6LO0LE AN 2 6 LOOLE Temperature control probe mode with HC4693 HS4693 L4693 N4693 or NT4693 sensor FUN 4 This mode is different from the previous one in the fact that the external probe is not connected to LOCAL DISPLAY Being unable to autonomously establish the temperature it must be associated to at least one probe items HC4693 HS4693 L4693 N4693 or NT4693 The user is shown the temperature value measured by the associated probes the set temperature value and the adjustment of the local selector ZA Zone address ZB Zone address MOD Mode FUN Function F
4. f Local Display 10 KQ at 25 C BETA 3435 max length of the connection 10 metres Local Display shows the temperature value measured by the external probe the set temperature value and the local selector adjustment The operations that may be performed by user are variation of the temperature set using the local selector FAN COIL speed management Operating mode management ZA Zone address ZB Zone address MOD Mode FUN Function For simple systems where each zone controls at most one heating actuator and one air conditioning actuator both of the ON OFF type and on a system with only one pump per function the configuration of the system can be performed by simply connecting the configurators that identify the address of the device and in case of probe indicate the number of slaves present Functions A short pressure of keys 8 and 11 can be used to locally change the temperature by 3 C in relation to the settings received from the central unit A short pressure of key 6 can be used to select the mode of operation cycling through the OFF antifreeze thermal protection and automatic statuses respectively Each mode of operation is identified by a different icon A short pressure of key 2 will force the speed the fan coils cycling through speed 1 2 3 or automatic Legend Set temperature Fan Coil adjustment Fan Coil speed indication Temperature variation indication Fan Coil operation indication Change op
5. he pumps to control on the BUS The programming operation must be completed directly from the central unit The central unit can also be used for the calibration of the probe During the system setting stage it will be necessary to specify the actuators used for the heating system and those used for the air conditioning system as they operate in a complementary way Local Display Slave probe HC HS L N NT4685 HC HS L N NT4693 Socket Configurator Socket Configurator ZA 4 ZA 4 ZB ZB 7 MOD 1 MOD SLA FUN 4 SLA 1 Each mode of operation is identified by a different icon A short pressure of key 2 will force the speed the fan coils cycling through speed 1 2 3 or automatic
6. ion requirements The recommended installation height is 150 160 cm Cover plate Support Local display NOTE AXOLUTE LIVING LIGHT and LIGHT TECH series boxes supports and cover plates can be found in the General installation catalogue Scenario control mode FUN 1 Thanks to this mode it will be possible to manage and change 4 different associated scenarios of the F420 scenario module and activate them by pressing one of the 4 icons shown on the display A Room PL Light point MOD Mode FUN Function Scenario programming To program change or delete a scenario the programming of Module item F420 must be enabled confirmed by the programming status LED turning green press the lock unlock key for at least 0 5 seconds After this has been done proceed as follows 1 Press one of the four keys to which the scenario should be associated to for 3 seconds The screen shows the name and icon of the selected scenario and the programming bar to indicate that the learning procedure has started If the device does not receive any commands within 30 minutes from the start of the learning procedure programming will automatically stop 2 set the scenario using the corresponding controls for the various Automation Temperature control Sound system etc functions 3 confirm the scenario by quickly pressing on the display 4 to change a scenario or create new ones to associate to other pushbuttons repeat the procedure st
7. ly be used to select the type of function To set other parameters it will be necessary to connect Local Display to the PC and use the TiLocalDisplay Software from the PC using the dedicated TiLocalDisplay software Based on the configuration set the device can work in four different modes Scenario control mode With external probe 3457 Temperature control probe mode with HC4693 HS4693 14693 N4693 NT4693 probe Sound system control mode HD4685 HC4685 HS4685 L4685 N4685 NT4685 Front view FUN Gees S 1A A 1B PL PF C MOD Rear view NOILVWOLNY SLAAHS IWDINHDAL N 9 6LO0L4 AN 2 6 LOOLE HD4685 HC4685 HS4685 L4685 N4685 NT4685 TiLocal Display Software sample screenshots af Configuratore ZA Configuratore ZB Sonda locale Presenza i9 Parametri Configuratore SLA Main possible functions using the software Selection of the operating mode to set for the device temperature control scenarios sound system Configuration of the settings of the probe and of its parameters Configuration of the general device parameters e g screensaver Icon style definition Installation Local Display is installed using a traditional procedure using a box support and cover plate the device is not fitted with a temperature probe Therefore it will not be necessary to comply with the probe installat
8. of the associated amplifier and the name of the sources that can be controlled A Room 0 9 amplifier room PF Loudspeaker 1 9 amplifier loudspeaker MOD Mode 0 4 source switching ON FUN Function 2 NOTE with M 0 source 1 is switched on without first switching OFF the sources Follow Me mode Functions A quick pressure of keys 6 and 7 will respectively switch ON and OFF the associated amplifier If the associated amplifier is on an extended pressure of keys 6 and 7 may be used to adjust the volume the intensity of which will be displayed by means of an icon 5 A short pressure of keys 2 and 4 will respectively cycle through the sources installed in the system and launch a control for the currently active source If the associated amplifier is OFF and no source is on the screen will not show any information Press key 4 for 3 seconds to configure the alarm clock see the user manual for details SD OB WN HD4685 HC4685 HS4685 L4685 N4685 NT4685 7 2 3 6 4 5 Legend Indication of the amplifier status or radio frequency Cycling of sources radio aux Active source indication Change radio station Volume level indication Associated amplifier ON and volume increase Associated amplifier OFF and volume decrease Temperature control probe mode with external probe FUN 3 An external temperature probe item 3457 with the following characteristics can be connected on the back o
9. or simple systems where each zone controls at most one heating actuator and one air conditioning actuator both of the ON OFF type and on a system with only one pump per function the configuration of the system can be performed by simply connecting the configurators that identify the address of the device and in case of probe indicate the number of slaves present Example of configuration of a zone address 47 with Local Display and probe item HC4693 HS4693 L4693 N4693 and NT4693 Local Slave display probe Functions A short pressure of keys 8 and 11 can be used to locally change the temperature by 3 C in relation to the settings received from the central unit A short pressure of key 6 can be used to select the mode of operation cycling through the OFF antifreeze thermal protection and automatic statuses respectively HD4685 HC4685 HS4685 L4685 N4685 NT4685 The possible operations for the user are the adjustment of the set temperature using the local selector and the change of status of the probe In this mode the parameters that can be configured are the local display address which must coincide with the ZA ZB address of the associated probe the type of control of the pump the type of mode and the number of slave probes 0 9 probe address 1 9 probe address 0 8 Slave probe number 4 For more complex systems the probe can memorize the actuators to activate and t
Download Pdf Manuals
Related Search