User Guide
Contents
1. e If you experience nasal dryness or irritation using a humidifier is recommended Fitting 1 Hold the pillows away from your nose ensuring that the pillow size eg M with the left L and right R indicators are correctly facing towards you then guide the nasal pillows into your nostrils L into your left nostril R into your right nostril Pull the headgear over your head by holding the bottom strap and stretching it around the back of your head The top strap should sit comfortably on top of your head Tip There are raised logos on top of the frame so you can feel the correct way up when fitting in the dark 2 Move the mask away from your face then place it back to get a comfortable fit Ensure the nasal pillows fit securely into your nostrils with both pillows positioned upright English 3 ea Finally connect the end of the mask tubing into your device air tubing Your mask is now fitted and ready to use When the device is running a light breeze should be felt through the vent To inspect the vent place a finger close but not over the entire vent area Adjustment To achieve a comfortable fit adjust the split straps by spreading them apart to loosen or draw them closer together to tighten Removal To take off your mask system pull the mask and headgear by the split strap up and over your head Disassembly T 2 Holding the top of the mask tubing squeeze and pull the pillows away from the mask2. after cleaning and in the case of excess condensation Disassemble the mask then reassemble according to the instructions Refit or reposition your mask Adjust your headgear Check your mask is assembled correctly Pressure flow The mask contains passive venting to protect against curve rebreathing As a result of manufacturing variations the vent flow rate may vary Pressure Flow cm H O L min 4 20 E 3 8 29 E 12 37 16 43 20 49 5 10 D 4 6 8 10 12 14 16 18 20 Mask pressure cm H O Dead space Physical dead space is the empty volume of the information mask to the end of the swivel Using the large pillows it is 123 mL Therapy pressure 4 to 20 cm H20 English 1 Resistance Drop in pressure measured nominal at 50 L min 0 4 cm H2O at 100 L min 1 4 cm H2O Environmental Operating temperature 41 F to 104 F 5 C to conditions 40 C Operating humidity 15 to 95 non condensing Storage and transport temperature 4 F to 140 F 20 C to 60 C Storage and transport humidity up to 95 relative humidity non condensing Gross dimensions Large 23 23 H x 5 87 W x 1 18 D 590 mm H x 149 mm W x 30 mm D Mask frame system no headgear Mask setting options For S9 Select Pillows For other devices Select SWIFT if available otherwise select MIRAGE as the mask option Notes o The mask system does not contain PVC DEHP or phthalates o This product is not made with na
3. apparent cracking crazing tears etc the component should be discarded and replaced e Avoid connecting flexible PVC products eg PVC tubing directly to any part of the mask Flexible PVC contains elements that can be detrimental to the materials of the mask and may cause the components to crack or break Daily After each use e Disassemble the pillows from the frame according to the disassembly instructions e Thoroughly clean the separated mask components excluding headgear by gently rubbing in warm approximately 86 F 30 C water using mild soap e To optimize the mask seal facial oils should be removed from the pillows after use e Use a soft bristle brush to clean the vent e Inspect each component and if required repeat washing until visually clean e Rinse all components well with drinking quality water and allow to air dry out of direct sunlight Dry the vent by gently wiping with a cloth English 5 e When all components including the vent are dry reassemble according to the reassembly instructions Weekly e Handwash the headgear in warm approximately 86 F 30 C water using mild soap It may be washed without being disassembled Rinse well and allow it to air dry out of direct sunlight Reprocessing the mask between patients This mask should be reprocessed when used between patients Cleaning disinfection and sterilization instructions are available from the ResMed website www resmed com ma
4. they are compatible with the CPAP or bilevel device If used outside specification or if used with incompatible devices the seal and comfort of the mask may not be effective optimum therapy may not be achieved and leak or variation in the rate of leak may affect the CPAP or bilevel device function Discontinue using this mask if you have ANY adverse reaction to the use ofthe mask and consult your physician or sleep therapist Using a mask may cause tooth gum or jaw soreness or aggravate an existing dental condition If symptoms occur consult your physician or dentist As with all masks some rebreathing may occur at low CPAP pressures e Refer to your CPAP or bilevel device manual for details on settings and operational information e Remove all packaging before using the mask Using your mask When using your mask with ResMed CPAP or bilevel devices that have mask setting options refer to the Technical specifications section in this user guide for mask selection options For a full list of compatible devices for this mask see the Mask Device Compatibility List on www resmed com on the Products page under Service amp Support If you do not have internet access please contact your ResMed representative Notes o This mask is not compatible for use with ResMed AutoSet CS 2 and VPAP Adapt SV devices o SmartStart may not operate effectively when using this mask with some CPAP or bilevel devices that have this feature
5. User Guide English AirFit Pio Nasal Pillows System Fitting Mise en place Colocaci n Colocac o Removal Retrait Remoci n Remoc o Reassembly Remontage Montaje Remontagem English AirFit P10 NASAL PILLOWS SYSTEM Thank you for choosing the AirFit P10 This document provides the user instructions for the AirFit P10 and AirFit P10 for Her masks referred to collectively as AirFit P10 throughout this manual AirFit P10 has blue headgear while AirFit P10 for Her has pink headgear Using this guide Please read the entire guide before use When following instructions refer to the images at the front and back of the guide Intended Use The AirFit P10 channels airflow noninvasively to a patient from a positive airway pressure PAP device such as a continuous positive airway pressure CPAP or bilevel device The AirFit P10 is e tobe used by patients gt 66 Ib 30 kg for whom positive airway pressure has been prescribed e intended for single patient re use in the home environment and multipatient re use in the hospital institutional environment GENERAL WARNINGS e The mask must be used under qualified supervision for users who are unable to remove the mask by themselves The mask may not be suitable for those predisposed to aspiration e The vent must be kept clear e The mask should only be used with CPAP or bilevel devices recommended by a physician or respiratory therapi
6. carthur Drive Bella Vista NSW 2153 Australia Distributed by ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA ResMed UK Ltd 96 Jubilee Ave Milton Park Abingdon Oxfordshire 0X14 4RW UK See www resmed com for other ResMed locations worldwide For patent information see www resmed com ip AirFit is a trademark of ResMed Ltd 2013 ResMed Ltd
7. frame Remove the headgear from the stabilizers by holding the fabric end of each strap and pulling out to reveal the buttonhole then sliding over the node and off the end of each stabilizer Your mask is now disassembled Reassembly iR With the gray side facing out insert each end of the headgear strap over the stabilizers through the buttonholes Secure in place by wrapping each strap end up and around the nodes Holding the split straps pull the headgear from the stabilizer to ensure it is tightly secure around the nodes Ensure the headgear strap is not twisted Attach the pillows to the mask frame by inserting the top and bottom clips into the correct slots shorter clip into top slot longer clip into bottom slot on the mask frame Your mask is now reassembled Ensure the inner walls of the nasal pillows are not compressed or collapsed If they are squeeze each nasal pillow so they return to the correct shape Cleaning your mask at home Your mask and headgear should only be gently handwashed The mask vent may discolour over time due to dust Follow the cleaning instructions in this guide to maintain performance and safety of the mask WARNING Always follow cleaning instructions and use mild soap Some cleaning products may damage the mask its parts and their function or leave harmful residual vapours that could be inhaled if not rinsed thoroughly CAUTION e f any visible deterioration of a system component is
8. r information on your warranty rights contact your local ResMed dealer or ResMed office Mask components Composants du masque Piezas de la mascarilla Componentes da m scara Headgear Harnais Arn s Arn s Split strap headgear Harnais avec sangle a laniere double Arn s con correa dividida Arn s com correla dividida Buttonhole Boutonni re Ojal Botoeira Fabric end Extr mit en tissu Extremo de tela Extremidade de tecido Pillows Coussins Almohadillas Almofadas Nasal pillows Masque narinaire Almohadillas nasales Almofadas nasais Frame Entourage rigide Armazon Armac o Stabilizer Stabilisateur Estabilizador Estabilizador Node Noeud Saliente Ressalto Vent Orifice de ventilation Ventilaci n Respiradouro Mask tubing Circuit du masque Tubo de la mascarilla Tubo da m scara Pillows system frame system Coussins support complet Sistema de almohadillas Sistema de armaz n Sistema de almofadas sistema da armac o Complete system Systeme complet Sistema completo Sistema completo XS Extra Small Tr s petit Extra pequeno Extra Pequeno S Small Petit Peque o Pequeno M Medium Moyen Mediano Medio L Large Grand Grande Grande AirFit Pio ResMed Global leaders in sleep and respiratory medicine www resmed com 618278 1 2013 10 taal Manufacturer ResMed Ltd 1 Elizabeth Ma
9. ranty is only available to the initial consumer It is not transferable If the product fails under conditions of normal use ResMed will repair or replace at its option the defective product or any of its components This limited warranty does not cover a any damage caused as a result of improper use abuse modification or alteration of the product b repairs carried out by any service organization that has not been expressly authorized by ResMed to perform such repairs and c any damage or contamination due to cigarette pipe cigar or other smoke Warranty is void on product sold or resold outside the region of original purchase Warranty claims on defective product must be made by the initial consumer at the point of purchase This warranty replaces all other expressed or implied warranties including any implied warranty of merchantability or fitness for a particular purpose Some regions or states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you ResMed shall not be responsible for any incidental or consequential damages claimed to have resulted from the sale installation or use of any ResMed product Some regions or states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from region to region For furthe
10. sks sterilization americas If you do not have internet access please contact your ResMed representative Troubleshooting Problem possible cause Solution Pillows won t seal properly mask is uncomfortable or causes red marks Pillows may have been fitted Check that the nasal pillows with the incorrectly adjusted incorrectly left L and right R indicators are or the headgear is fitted inserted correctly L into your left incorrectly nostril R into your right nostril Carefully follow the fitting instructions Readjust the headgear to ensure it is fitted comfortably Inner wall position of one or both Squeeze pillow sides to release inner pillows is incorrect wall The correct position is shown in the reassembly instructions Pillows are the wrong size Talk to your clinician Pillows may be dirty Clean pillows according to the instructions Headgear is too loose Wash headgear to help it return to its original form Follow the washing instructions Adjust the headgear split straps Problem possible cause Vent is blocked or dirty discolored Vent is wet Mask too noisy System is assembled incorrectly System is leaking air Technical specifications Solution If the vent requires cleaning use a soft bristle brush The vent may discolor over time and this is not a safety concern Follow the cleaning instructions in this guide to maintain performance and safety of the mask Ensure the vent is dry
11. st e The mask should not be used unless the device is turned on Once the mask is fitted ensure the device is blowing air Explanation CPAP and bilevel devices are intended to be used with special masks or connectors which have vent holes to allow continuous flow of air out of the mask When English 1 the device is turned on and functioning properly new air from the device flushes the exhaled air out through the mask vent holes However when the device is not operating insufficient fresh air will be provided through the mask and the exhaled air may be rebreathed Rebreathing of exhaled air for longer than several minutes can in some circumstances lead to suffocation This applies to most models of CPAP or bilevel devices Follow all precautions when using supplemental oxygen Oxygen flow must be turned off when the CPAP or bilevel device is not operating so that unused oxygen does not accumulate within the device enclosure and create a risk of fire Oxygen supports combustion Oxygen must not be used while smoking or in the presence of an open flame Only use oxygen in well ventilated rooms At a fixed rate of supplemental oxygen flow the inhaled oxygen concentration varies depending on the pressure settings patient breathing pattern mask point of application and leak rate This warning applies to most types of CPAP or bilevel devices The technical specifications of the mask are provided for your clinician to check that
12. tural rubber latex o The manufacturer reserves the right to change these specifications without notice Storage Ensure that the mask is thoroughly clean and dry before storing It for any length of time Store the mask in a dry place out of direct sunlight Disposal This mask does not contain any hazardous substances and may be disposed of with your normal household refuse Symbols The following symbols may appear on your product or packaging CATALOG NUMBER o HUM DITY LIMITADOS FRAGE PATH CARE Re onty PP Catalog number LOT Batch code BATCH ODE Humidity limitation awe a Temperature limitation x Not made with natural Fragile handle with care ZOS B latex ECREP European Authorized Manufacturer Representative Keep away from rain t This way up THE WAY Li Indicates a Warning or Caution and alerts you to a possible injury or explains special measures for the safe and effective use of the device Caution consult accompanying documents Prescription only In the US Federal law restricts these devices to sale by or on the order of a physician Polypropylene recyclable English 9 Limited warranty ResMed Ltd hereafter ResMed warrants that your ResMed mask system including mask frame cushion headgear and tubing shall be free from defects in material and workmanship from the date of purchase for the period of 90 days or in the case of disposable masks the maximum use period This war
Download Pdf Manuals
Related Search