User Manual - Pro-Ject Audio Systems
Contents
1. e Unlock and slide open the battery case cover e Replace the battery Make sure the battery is the right way round e Close the battery case cover Battery type 1 x CR2032 3V or 1 x CR2025 3V Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Technical specifications Pro Ject Stereo Box S Phono Power output 2 x 25W 37W at 8 ohms 4 ohms both channels driven Frequency response 20Hz 20kHz 1 5dB Channel separation gt 40dB at 20kHz Noise floor gt 100dBA THD lt 0 1 at 10W Gain 31dB Line level inputs 3 pairs RCA phono sockets IN2 IN3 IN4 Phono input 1 pair RCA phono sockets IN1 Phono amplifier Moving magnet MM RIAA equalisation curve accuracy 20Hz 20kHz max 0 5dB Input impedance 20kohms Speaker connectors 4mm banana plugs spades connectors or naked wire Outboard power supply 20V 3A DC suitable for your country s mains supply Power consumption 3A DC lt 1W in standby Replacement battery remote control 1 x CR2032 3V or 1 x CR2025 3V Dimensions W x H x D D with sockets 206 x 40 x 150 165 mm Weight 1120g without power supply Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only when the problem cannot be resolved there should2. 10 CID CIA BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Stereo Box S Phono Dear music lover Thank you for purchasing a Pro Ject Audio Systems integrated amplifier In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse 15 Important notice Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power supply is used to disconnect the unit from the mains Make sure that the power supply is easily y accessible at all times Never handle the device the power supply while your hands are wet or damp Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Connectors o IN1 IN2 IN3 Jr Fix Power KO O 0 S 0o 0 MA ANDA ANA A PHONO Pro Ject Audio Systems ae Austria ed OUT 1 Make all connections except the connection to the headphone and USB whilst the unit is disconne
3. the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 5 for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Copyright trademarks Pro Ject Audio Systems is a Registered Trademark of The information was correct at the time of going to H Lichtenegger press The manufacturer reserves the right to make This guide was produced by Pro Ject Audio Systems changes to the technical specification without prior Copyright 2015 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 4 Pro Ject Audio Systems gt Pro Ject Stereo Box S Phono Revision 2015 1 8
4. analogue record device or a Pro Ject Head Box headphone amplifier nes OUT Fix provides a fixed output level Pre Out A power amplifier or active loudspeakers can be connected to the output sockets marked OUT Var Connection to the speakers The output terminals accept loudspeaker cables terminated with 4mm Banana plugs spades connectors or naked wire Mains power connection The unit is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug from the power supply to the Power 20V DC socket before connecting the power supply to the mains S turns the unit on or back into standby voi and adjust the sound volume D CH and select the inputs Remote control ON OFF Front panel controls o gt 4 Stereo Box S Phono To switch on from standby or to standby The push button on the left side of the front panel turns the unit on or back into standby The blue LED above the stand by push button shows that the unit is switched on Input selector After the unit is powered on pressing the buttons and P gt next to the LEDs inputs indicators selects desired input Volume Adjust the volume to the desired level using the large knob on the front panel Pro Ject Audio Systems Pro Ject Stereo Box S Phono Revision 2015 1 8 3 Replacing batteries Proceed as follows
5. cted from the mains 2 Never connect or disconnect power supply to or from the unit whilst the power supply is connected to the mains Never use any other power supply than the one supplied with the unit with the exception of dedicated Power Boxes which can replace original power supplies 3 Take care to connect the left and right channels of In1 In2 In3 In4 correctly The right channel is V usually marked red the left channel black or white 4 Speaker connections for the left speaker are located on the right hand side of rear view above connections to right speaker are located near the power socket Speaker connectors marked red represent according indicators on speaker terminal The red speaker terminals carry the positive signal the black speaker terminals the negative signal Make sure the polarity of the connection is correct at each end of the cables Only connect one loudspeaker with an impedance not less than 4 ohms per channel Connecting the record player MM or high output MC cartridges only Connect the tonearm signal lead to the IN1 The earthing wire may be connected to the screw terminal if you encounter hum problems when using the record player Connecting line level sources Line level sources such as CD player radio or TV can be connected to the input sockets marked IN2 IN3 or IN4 2 Pro Ject Audio Systems gt Pro Ject Stereo Box S Phono Revision 2015 1 8 Record output OUT Fix connects an
Download Pdf Manuals
Related Search