Star Wars Darth Vader Lightsaber with Removable Blade
Contents
1. Adult Collectible 94731 94729 Asst TAD DE a 7 ZN a FX LIGHTSABER COLLECTIBLE with Removable Blade FORCE Xx ALKALINE 1 5V AAA or LRO3 3 BATTERIES NOT INCLUDED REQUIRED Phillips cross head screwdriver not included needed to insert batteries Some assembly required PLEASE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE Never use to strike people or animals BAT TERY DAUA ASAN Continued 4 Using a Phillips crosshead screwdriver not included loosen screw in battery pack sleeve screw will remain attached to sleeve Slide sleeve off battery pack Insert 3 x 1 5V AAA or LRO3 size alkaline batteries in the battery pack Make sure the batteries are correctly Oriented refer to the and markings as a guide 6 To re insert the battery pack slide sleeve back onto pack and tighten screw Align the yellow arrow on the pack with the yellow triangle inside the hilt handle Slide it in until it stops DO NOT FORCE eo a Replace pommel end cap by screwing it on clockwise N S WARNING To prevent risk of electric shock or serious injury never disassemble the lightsaber blade e DO NOT attempt to perform any repairs yourself There are no consumer repairable parts inside e Never use to strike others This product is not intended for striking people animals or objects This product is not covered by warranty for damage caused by striking against hard objects e Never run2. and be sure to insert them correctly by matching the and polarity markings 3 Do not mix old batteries and new batteries or standard carbon zinc with alkaline batteries 4 Remove exhausted or dead batteries from the product 5 Remove batteries if product is not to be played with for a long time 6 Do not short circuit the supply terminals 7 Should this product cause or be affected by local electrical interference move it away from other electrical equipment Reset switching off and back on again or removing and re inserting batteries if necessary 8 RECHARGEABLE BATTERIES Do not mix these with any other types of batteries Always remove from the product before recharging Recharge batteries under adult supervision DO NOT RECHARGE OTHER TYPES OF BATTERIES FCC Statement ae This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to compy aui the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instr
3. with the lightsaber Never use the lightsaber in total darkness e Always check the area around you before swinging the lightsaber to ensure you do not injure anyone or cause damage e Turn off the lightsaber when not in use Never leave the lightsaber on when unattended e To prevent risk of electric shock or serious injury never immerse the lightsaber in water or allow the lightsaber to become wet Use only a soft dry cloth to clean e f the blade of the lightsaber becomes cracked or damaged stop using the lightsaber immediately BATTERVAINSTALUATIONT amp SASSEMBLY 1 Make sure the lightsaber is OFF 2 Unscrew pommel end cap counter clockwise to expose the battery pack 3 Completely remove the battery pack from the hilt handle S We P N 7041360000 Product and colors may vary 2010 Lucasfilm Ltd amp or TM where indicated All rights reserved and or amp 2009 Hasbro All Rights Reserved TM amp denote U S trademarks IMPORTANT BATTERY INFORMATION N CAUTION 1 As with all small batteries the batteries used with this product should be kept away from small children who still put things in their mouths If they are swallowed promptly see a doctor and have the doctor phone 202 625 3333 collect If you reside outside the United States have the doctor call your local poison control center 2 Always follow the instructions carefully Use only batteries specified
4. e FX Lightsaber for dueling A No This product should not be used to strike people or animals Although the blade is very durable it should never be used for fighting or dueling The Force FX Lightsaber was produced to be a collectible Q Sometimes see a dark spot in the middle of the blade Is there something wrong with the lightsaber A No The dark area is actually a result of the design All the Force FX Lightsabers are handmade and as a result this slightly dark area at the middle of the blade is normal This does not affect the performance of the lightsaber in any way
5. l marking One LARGE groove in front Support with Ill marking When the hilt and blade are attached Rest the hilt in the large groove and the blade in the Small groove Both LARGE grooves in front Support with I and Il marking Support with III marking When the hilt and blade are separated Rest the hilt in the LARGE grooves in the front and the blade in the SMALL grooves in the back e 00 Store the collar or cap and belt clip in the stand when it s not being used Yh f M Unscrew the cap and remove it from the hilt Slide the collar onto the blade Replace the blade in the hilt aligning the groove for the correct position Screw in the collar as you hold the blade in place and apply pressure to keep the blade pressed against the inside of the hilt Slide the sleeve on the blade and tighten the knob Q Is the Force FX Lightsaber a licensed collectible A Yes The Force FX Lightsaber is a licensed collectible approved and endorsed by Lucasfilm Ltd As a collectible the Force FX Lightsaber is not suitable for children under 14 years of age Adult supervision is recommended Q Is the Force FX Lightsaber a limited edition prop replica A No Although the design of the Force FX Lightsaber is faithful to the look of the movie prop it is not an exact replica The hilt of the Force FX Lightsaber was made slightly larger than the act
6. ual movie prop in order to accommodate the electronics that control the light and sound effects The Force FX Lightsaber collectibles are not limited to a pre determined edition size therefore they are not classified as limited edition replicas Q What is the blade on the Force FX Lightsaber made of A The Force FX Lightsaber features a polycarbonate blade Once activated the blade glows brightly and the replica plays back digitally recorded sound effects taken directly from the film Q Is the blade on the Force FX Lightsaber removable A Yes the blade is removable please refer to instructions on this sheet for proper removal Q How do the light and sound effects work in the Force FX Lightsaber A The Force FX Lightsaber incorporates motion sensors which sense both the motion of the blade as well as when it comes in contact with something An on board multi channel chip is programmed with digital sound effects originally created for the movie by Skywalker Sound The Force FX Lightsaber replicates the following sound effects e Power up e Idle hum e Swing with pitch change e Clash e Power down Q How long should the light in the Force FX Lightsaber last A It should run for several hours on a fresh set of batteries The electronics if cared for properly should last for several thousand hours of use Replace the batteries whenever the performance begins to change such as reduced brightness or volume Q Can use my Forc
7. uctions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Consult the dealer or an experienced radio TV technician for help CAUTION Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment On Off Locate the ON OFF switch on the control panel as shown in the diagram To turn the lightsaber ON slide the switch forward away from you To turn the lightsaber OFF Slide the switch backward toward you sounds if you press the button when the blade is separated from the hilt S Unscrew the knob Unscrew the collar NOTE the knob is captive and is designed to remain attached to the sleeve Slide the sleeve off the blade Slide the collar off the Remove the blade blade Slide the sleeve onto the hilt and tighten the knob The holders on the stand can be positioned differently for multiple display options One SMALL groove in front Support with I and I
Download Pdf Manuals
Related Search