System Setup
Contents
1. 2 SCHLAG E LINK System Setup The lock should already be installed on your door If not use the installation instructions document number Q i to install the lock and then come back to this document Lock Programming Code Important Information six 6 digits Bridge MAC ID twelve 12 characters Web Support part2 schlage com Customer Service 877 288 7707 L Locate the programming code on top of the lock installation R tM SCHILAGE staetion instructions instructions document Q Write the programming code in OLIN the Important Information box at the top of this page e The programming code is six digits long and is located on the yellow sticker on the installation sheet that is packed in the box e The programming code can be changed If you have changed your programming code the code that is printed on the label will not work See Manual Lock Programming at part2 schlage com e If you don t remember your programming code you can reset your lock which will restore the original programming code See Manual Lock Programming at part2 schlage com 2 Locate the bridge MAC ID Write the MAC ID in the Important Information box at the top of this page e The MAC ID is 12 characters long and is located on the yellow label inside the battery compartment of the bridge Install the light module e The light module can be used to control a lamp e The light module repeats the Z Wave signal2. In some homes the light module must be used to improve communication between the bridge and the lock See the Understanding Signals section for more information During the online portion of the setup the system will determine if it is communicating properly or not You can move the light module during online setup if necessary e The light module should be installed into any indoor three prong 120 volt A C outlet 4 Optional Plug a lamp into the Z Wave two prong side of the light module e There are two outlets on the light module One of the outlets has only two prongs and is labelled with a Z Wave sticker A lamp 25 wave watts minimum and 300 watts maximum can be controlled by the o Max 30 system if it is plugged into the Z Wave side of the light module Incandescent Use only an incandescent light bulb in the lamp that is plugged into the light module DO NOT use a CFL compact fluorescent light bulb or any other kind of electric device The other outlet has three prongs and can be used simply as a pass through outlet 1500 watts maximum It is not controlled by the system and the system is not affected when it is used Install the 9 volt battery into the bridge e Use the 9 volt battery that is included in the box e Use any premium quality 9 volt battery for replacement Initialize the bridge a Press and hold the plus and minus buttons simultaneously for 10 seconds Release
3. fully apply Refer to your local laws for your specific rights under this warranty Guaranteed Fit Program Schlage products are designed to fit standard residential door preparations and retrofit existing tubular locks Note Mortise locks and preparations are not considered standard and are not guaranteed under this program During the initial installation if there is a problem with the Product s performance the Original User may simply contact Schlage Customer Service at 877 288 7707 in the U S and Canada Program and warranty claims If you encounter a residential door preparation or fit issue under the Guaranteed Fit Program or have a claim under this warranty please contact Schlage Customer Service for repair replacement or refund of the original purchase price in exchange for the return of the Product to Schlage am Ingersoll Rand Residential Solutions 2010 Schlage Lock Company link system setup Rev 03 10 b
4. 8829 5152558 5769472 6533336 D372854 D467155 5308131 5809816 6540274 D406056 D472788 5395144 5816086 6581426 D406528 D487388 5593193 5820290 6802546 D426452 D520331 5598726 5881590 6905773 D428324 D520332 5640863 5918916 6926319 D450558 D537702 5683127 6286347 7148477 D457048 D541620 5715717 6297725 7159424 D457049 D543435 LOCK PRODUCT Lifetime Limited Mechanical and Finish Warranty and 1 Year Limited Electronics Warranty Subject to the terms and conditions of this warranty Schlage extends a lifetime limited mechanical and finish warranty and a one year limited electronics warranty to the original consumer user Original User of our Schlage brand lock product Lock Product against defects in material and workmanship as long as the Original User occupies the residential premises upon which the Lock Product was originally installed NON LOCK PRODUCT 1 Year Limited Mechanical and Electronics Warranty Subject to the terms and conditions of this warranty Schlage extends a 1 year limited mechanical and electronics warranty to the original consumer user Original User of our Schlage brand non lock product used in conjunction with our Lock Product Non Lock Product against defects in material and workmanship as long as the Original User occupies the residential premises upon which the Lock Product was originally installed Lock Product and Non Lock Product are collectively referred to herein as
5. Product What Schlage will do Upon return of the defective Product to Schlage Schlage s sole obligation at its option is to either repair or replace the Product or refund the original purchase price in exchange for the Product Original User This warranty only applies to the Original User of Products This warranty is not transferable What is not covered The following costs expenses and damages are not covered by the provisions of this limited warranty i labor costs including but not limited to such costs as the removal and reinstallation of Product ii shipping and freight expenses required to return Product to Schlage iii failures defects or damage including but not limited to any security failure or loss of data caused by any third party product service or system connected or used in conjunction with the Product and iv any other incidental consequential indirect special and or punitive damages whether based on contract warranty tort including but not limited to strict liability or negligence patent infringement or otherwise even if advised of the possibility of such damages The provisions of this warranty do not apply to Product i used in commercial applications ii used in common area applications iii used for purposes for which they are not designed or intended iv which have been subjected to alteration abuse misuse negligence or accident v which have been improperly stored
6. both buttons The orange light on the bridge will continue to flash for 10 15 seconds e This procedure can be used to initialize the bridge at any time See System Reset at part2 schlage com for more information L Enroll the light module into the bridge a Hold the bridge within 6 feet 1 8 meters of the light module throughout all of step 7 Press and release the plus button on the bridge Double click the button on the light module d Observe the lights on bridge The orange light will blink while enrollment is taking place Enrollment is complete when the orange light becomes solid 8 Enroll the lock into the bridge e Before you begin this step find the six digit lock programming code located in the Important Information box on the first page For your convenience there is space to write the programming code below e After you begin the enrollment process you have 30 seconds to complete the remainder of the steps The bridge must remain within 6 feet 1 8 meters of the lock throughout the enrollment process Q OO OOOO 0010 00 OOOO 0000 OOOO Press Press Observe es then gt Blinking On Bridge Six digit lock programming code On Lock On Lock Observe Wait For Observe eS gt Success Blinking 3 Lights 3 Beeps Blinking Repeat this process for additional locks NOTE ONLY if you observe a red blinking light instead of a green blinking light exclude the lock f
7. f they are pointing at each other No Communication In this drawing there is no communication between the Bridge and Lock The signal is first diminished by the wall Then then signal is blocked entirely by the metal object Limited Communication In this drawing the Light Module and the Bridge can communicate but the Lock can still not communicate with anything Good Communication In this drawing the signal problem is fixed by placing the Light Module in a location that has good communication with both the Bridge and the Lock The Light Module repeats the signal from the Bridge to the Lock L Area of Good Communication FCC Notice This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications to this equipment not expressly approved by Schlage could void the user s authority to operate the equipment FCC ID P2GBE369 IC 7954A BE369 FCC ID P2GFE599 IC 7954A FE599 FCC ID P2GBR100 IC 7954A BR100 PATENT NOTICE Schlage products and those of its subsidiary companies and licensees may be covered by both issued and pending U S and foreign patents copyrights and trademarks Manufactured items are covered by one or more of the following patents 5070715 5765412 6523375 D372417 D45
8. installed maintained or operated vi which have been used in violation of written instructions provided by Schlage vii which have been subjected to improper temperature humidity or other environmental conditions or viii which based on Schlage s examination do not disclose to Schlage s satisfaction non conformance to the warranty Additionally this warranty DOES NOT COVER scratches abrasions or deterioration due to the use of paints solvents or other chemicals Exclusions Oil Rubbed Bronze finish 613 is designed to improve over time and change in appearance creating a living finish through daily use and thus finish discoloration is not applicable to the above warranty Additional terms Schlage does not authorize any person to create for it any obligation or liability in connection with the Product Schlage s maximum liability hereunder is limited to the original purchase price of the Product No action arising out of any claimed breach of this warranty by Schlage may be brought by the Original User more than one 1 year after the cause of action has arisen How local law applies This warranty gives you specific legal rights and you may also have other rights as otherwise permitted by law If this Product is considered a consumer product please be advised that some local laws do not allow limitations on incidental or consequential damages or how long an implied warranty lasts so that the above limitations may not
9. rom the bridge and then try enrollment again a Press and release the minus button on the bridge b Enter the six digit programming code on the keypad and wait for three orange lights and three beeps c Press the Schlage button and then the zero 0 button on the keypad and wait for three orange lights and three beeps d Wait for all lights to stop blinking You should then be able to enroll the lock normally 9 This portion of the setup is complete For the next portion you will need a computer that is connected to the Internet e Internet Explorer 7 0 or Firefox 3 0 is required for proper operation You can check your browser version by clicking Help gt About in the browser s menu If you do not have the proper version you can download a newer version from the following web sites e Internet Explorer 7 0 www microsoft com windows downloads ie getitnow mspx e Firefox 3 0 www mozilla com Using either Internet Explorer 7 0 or Firefox 3 0 browse to www schlagelink com Look for Just purchased a Schlage LINK System Click here and click the link Understanding Signals Below are some examples of how signals interact with objects you may have in your home Walls will diminish the signal Metal objects such as refrigerators or file cabinets will block the signal entirely Also notice that the signals for the Light Module and the Lock are directional The Lock and Light Module have a better chance of communicating i
Download Pdf Manuals
Related Search