F1CWS Evo User Guide
Contents
1. P3 Removingthe Top Panel The top panel is held in place by 2 long screws that are accessed from the bottom of the case With the chass s upside down remove the 2 screws from either side The top panelcan now be lifted off the chassis Removing the HDD Cage The HDD cage Is held in place by 6 screws which are all accessible from the top of the case Remove all 6 screws and lift the cage out of the chassis 2510 Fitting Cooling Fan amp IRRC Module Optional Y4x10 The FICWS Evo can accommodate a 40 or 60mm fan gt 60mm may interfere with fitting of 2 5 HD see HDD k i es installation The fan bracket is packed with the other screws and accessories Fit your purchased fan with 2 screws as shown Depending on 40 or 60mm Fit the fan assembly to the case using a single screw from under the chassis The IRRC module can be installed into the position shown in red using 2 screws supplied P4 PREPARING FOR ASSEMBLY Installing the Motherboard Locate the I O shield that is supplied with your motherboard and firmly push it in place Ensure that it fully clips in place otherwise the motherboard will be difficult to fit The motherboard should be prepared ready for installation by fitting CPU cooler and RAM ng AN M3 x 4 Carefully lower the motherboard into the chassis with the 1 0 port side leading so that the ports align with the I O shield holes and can fit correctly When the motherboa2. STREACOM FRIESE USER GUIDE Dates Index Foreword ce Product Overview ee Preparation for Assembly SAAMA Installing the Motherboard lu aia e Installing the Hard Drives AMM Replacing the HDD Cage and Top Panel Foreword Thank you for your purchase of this Streacom product every care has been taken to ensure that It meets with the high standards that we have set for ourselves Should you have any questions that are not covered in this user guide support can be offered via email through our website at www streacom com We sincerely hope that you enjoy using our product P2 INDEX Specification Chassis Material Aluminum Available Colours Motherboard Compatibility HDD Drive Support ODD Drive Support Cooling Method Dimensions Power Supply Support IR Solution Net Weight Mini ITX None 1 6KG 2 Key Features e IR Receiver Window PER Top Panel Iein Power LED 4 Power Button u 40 or 60mm Fan Bracket Fan not Included Silver Black sandblast finish 1x3 5 1x2 5 or 3x 2 5 depending on components installed 1 x 40x40x10mm or 1 x 60x60x10mm fan not Included 197 x 197 x 77mm LxWxH 3mm feet NanoPSU 8 external DC adapter not included Streacom IRRC receiver 8 remote not included Os IO Shield Opening las Power Button PCB u DC Power Jack Hole 9 IR Receiver Mounting IRRC Not Included 10 HDD Mounting Cage OVERVIEW
3. many drives are used and positioning requirements Replacethe HDD Cage With the hard drives fitted the cage can now be replaced into the chassis Carefully lower the assembly ensuring cables are routed correctly connected and that there is no component conflict The HDD cage should be secured to the chassis using 8 screws in total 6 at the top and 2 from underneath Note that the 2 screw underneath fix to the 2 5 hard drive so if no 2 5 drive ts installed these screws can be Ignored Replace the Top Panel With all the components installed all that remains is to replace the top panel and secure it in place with the 2 long screws from underneath the chassis When replacing the top panel ensure the correct orientation as the 2 long securing screws should match up with the nuts in the top panel REPLACING THE HDD CAGE AND TOP PANEL P7 TRACOM
4. rd is correctly in position fix it to the chassis stand offs using the screws provided Ensure that all the holes correctly align before fully tightening the screws Connect NanoPSU amp Other Cables With the motherboard in place you can now connect the PSU and any other internal connectors such as the power button switch You should also connect the SATA cables in perpetration for installing the hard drives INSTALLING THE MOTHERBOARD P5 Installing the Hard Drives Depending on the type of components fitted you can install a maximum of 1 x 3 5 1x 2 5 or 3 x 2 5 hard drives If fitting a 3 5 hard drive there are a 4 positions and 2 orientations that can be used as shown in the diagram Select a location and orientation that best suits component and cabling requirements Rubber pads supplied can be affixed to the mounting holes used in order to reduce mechanical vibration if SSD s are not used P6 FITTING THE HARD DRIVES The primary 2 5 hard drive can be mounted vertically using 2 screws Ensure that the HDD connectors are facing toward the back of the chassis Please note that if you are using a 60mm fan a 90 degree power sata connector must be used to avoid conflict with the fan If not installing a 3 5 hard drive 2 x 2 9 hard drives can be fitted horizontally as shown There are a total of 3 mounting positions available for the 2 5 drives which can be selected depending on how
Download Pdf Manuals
Related Search