Manual (english)
Contents
1. You can solder this end resistor on a 3pin or 5pin XLR Plug this adapter into the DMX output of the device 3 3 DMX connection with terminator Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy environment like a disco for installations we recommend using a DMX terminator This prevents corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR connector with a 120 O resistor between pins 2 and 3 which is then plugged into the XLR output socket of the last device in the series Please look to the bottom drawings COMMON DMX O1 DMX Eg Not Used 0405 Not Used COMMON LZ IN DMX INPUT DMA DMX OUTPUT o DMX 9 12 DMX INPUT DMX OUTPUT VARYTEC 1209 2 PIN 3 PIN2 If you using a controller with 5 pins DMX output you need to use a5 to 3 pin adapter cable 4 Control To get to the menu you have to press MENU With UP DOWN you can scroll through the menu If you have reached the desired point of menu press ENTER With UP DOWN you can make your desired settings Conform your settings with ENTER 4 1 Structure of the menu Main Menu Submenu Function description Axxx A001 A255 Set the DMX address disp Yes Reverse the display LodR Yes Reset to factory settings uEr Shows the software version AFxx AF00 AF16 Set the speed of strobe Sout Sound to light 5 DMX Chart Channel Value Value to Function2. Containers with water should not be placed on the set Keep away from sources of hum and noise Such as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the device for an extended period of time be sure to disconnect the plug from the receptacle 3 12 VARYTEC Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards 1 2 Further safety instructions IMPORTANT Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried o
3. VARYTEC Manual Strobe Mini LED20 VARYTEC 1 2 3 4 5 6 Table of contents Safety INSIFUCHIONS D 3 1 1 FOR SAFE AND EFFICIENT OPERATION i 3 1 2 Furthersately INSTUCUONS isaac ia 4 o A 9 Connections eere ree khi Fee tage dad adan aiar 9 3 1 Electrical connections erre ene rr RN eran EK aa RAN Ne Ein RRA 9 3 2 DMX COMNMECTIONS e MC ERREUR 9 3 3 DMX connection with terminator cece eeeeeeceaeaeeeeeeeseceaaaeeeeeeeeeseccaeeeeeeeeeeeeea 9 Seem in bei 10 4 1 Structure of the MEnu ice iii 10 DMX GEA m 10 BE eH 11 2 12 VARYTEC 1 Safety instructions e This device is suitable for indoor use not outdoors only e All modifications to the device will void the warranty e Repairs are to carry out by skilled personnel only e Use only fuses of the same type and original parts as spare parts e Protect the unit from rain and humidity to avoid fire and electric shocks e Make sure to unplug the power supply before opening the housing 1 1 FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 32 F 0 C or exceeding 104 F 35 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust
4. from 1 0 255 Dimmer 2 0 255 Set the speed 3 0 255 Special effects 10 12 VARYTEC 6 Technical data Power supply Voltage Power consumption max Battery Light source LM type Power Number Power Optics Flash rate Connections Current in Current out XLR in out Controlling Sound to light Automatic Master Slave DMX512 Hardware Protection class Dimensions L B H Weight AC110 240V 50 60Hz 28 W No SMD LEDs 19 2 W 48 0 4 W 0 20 Flashes s Schutzko No 3Pin Yes Yes Yes 3 channels IP20 219x135x205mm 1 kg 11 12 VARYTEC Importer B amp K Braun GmbH Industriestra e 2 D 76307 Karlsbad www bkbraun com info bkbraun com CE A RoHS So 2002 95 EC 12 12
5. of device Only safety ropes with quick release safety fastener elements may be used Hang up the safety rope in the hole of the mounting bracket Direct the rope over the 7 12 VARYTEC truss or an appropriate fastening point Hang up the end in the fastening element and tie up the locking nut A safety rope once exposed to failing load or damaged may not be used furthermore The maximum drop exceed must not exceed 20cm A safety rope once exposed to failing load or damaged may not be used furthermore Adjust the desired inclination angle via the mounting bracket and tighten the screw 8 12 VARYTEC 2 Introduction Thank you for buying the Strobe LED 100DMX It is a powerful device For a successful installation and operation please read this manual carefully 3 Connections 3 1 Electrical connections If you wish to change the power supply settings see the chapter Appendix Connect the fixture to the mains with the enclosed power cable and plug The earth has to be connected Cable EU Cable US Pin International Brown Black Live L Light blue White Neutral N Yellow Green Green Earth 3 2 DMX connections To make a DMX512 connection go ahead like it is described in the picture Make sure that you use shielded cable 3pole or 5pole XLR cables are suitable Important After the last device the line has to be terminated In order to do this you have to solder a 1200 resistor between the pins Data and Data
6. sharp edges Assure yourself with regular checks that there are no damages to the power cable or the device Don t switch the device in short time intervals e g in second cycle on or off Keep away children and laymen off the device Health risk Don t look directly into the light source At certain circumstances it is possible that some people get epileptic seizures This is especially true for individuals whose epilepsy was determined by a doctor Therefore do not install it in danger zones such as stairs exit routes Point out the visitors before operating on the use of a strobe Avoid prolonged flash sequences Designated use This device was developed for professional use on stages in discos theatres etc The device is only approved for a connection up to 230V 50 60 Hz AC voltage and only for indoor use Regular breaks during operation increase the lifetime of your device Avoid convulsions or any form of forceful impact during the installation or the start up of the device Make sure that the device is not exposed excessive heat humidity or dust at the place of installation Take care that no cables are lying around You would endanger your own safety and also the safety of a third party It is not allowed to operate or store the device in an environment in which spray water rain humidity or fog is expected Humidity or very high atmospheric humidity could reduce the isolation of the device and could cause deat
7. frame of the inspection test at least all four years by an expert Review by a qualified person at least once a year How to carry out the overhead installation In tidal fall you should install the device out of the lounge area of people IMPORTANT Overhead installation requires a high level of experience This includes knowledge of calculating the payload used installation material and safety inspections of the used material and the projector whereas the required experience is not limited to this Do not try to carry out installation yourself under any circumstances if you are not qualified Contact a professional installer An inappropriate installation can lead to injuries and or damaged properties It is not allowed to install the device in the grip area of people If the device may hang from the ceiling or from high beams the use of truss systems is mandatory The device may not be installed so it can swing freely in the room Please note Crashing down items can cause serious injuries Do not install the projector if you doubt the safety of a possible installation form Before installation make sure that the mounting surface has the ability to carry the tenfold point load of the own weight of the device Mount the device with the mounting bracket to your trussing system using an appropriate clamp During overhead installation the device must be always secured by a safety rope which is designed to hold the twelvefold weight
8. hly electric shocks If you use fog devices the device has not be exposed to a direct smoke jet There has to be a safety distance of at least 0 5m between this device and the fog machine Make sure that the saturation of the fog has to enable a visibility of at least 10m The ambient temperature has to be between 0 C and 40 C Avoid direct sunlight and close proximity to heaters You have also to attend it during the transport in closed motor vehicles 5 12 VARYTEC You have to attend that with an ambient temperature von 40 C it is not allowed that the relative humidity exceeds 50 Operate the device not during thunderstorms Surge voltages could destroy the device Unplug the power supply during thunderstorms During the installation the use of the mounting bracket is obligatory Surrounding objects or surfaces should not be in contact with the device Make sure that during the installation and removal of the device the area below the place of installation is basically cordoned off This also applies to implementation of service The device has basically been protected by a suitable safety Make familiar yourself with the functions of the device before start up People without the experience should not handle with the device The most cause of functional disorder is inappropriate handling Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn di
9. rt For transport use the original packing or designated accessory to avoid damages during the transport For reasons of safety unauthorized changes are forbidden A usage of the device which differs from usages which are described in this manual can cause damages of the device In that case the warranty expires Additional you should notice that every differed usage is related with dangers and can cause e g an electrical short fire electric shock or crash Overhead installation Danger of life You have to observe the regulations of BGV C1 formerly VBG 70 and EN60598 2 17 Installations are to carry out by skilled personnel only The suspension devices have to be build and measured so they can withstand for an hour the tenfold of the payload without suffering a permanent detrimental deformation 6 12 VARYTEC Basically installation has to be made by using a second separate suspension This can be e g a suitable net The second suspension must be designed and attached so no part of the installation can fall down in case of failure During construction reconstruction and deconstruction unnecessary stay in the range of moving areas on lightning bridges under elevated work stations or any other danger zones is forbidden The operator is obliged to following safety related and mechanical facilities Before the first start up or after critical changes before restarting it has to be checked by an expert Review in the
10. ut by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards IMPORTANT Keep away from water and humidity Make sure to unplug the power supply before opening the housing Please read careful through this manual before the first start up All persons which are entrusted with installation start up operation maintenance and repair of this device have to e Show a corresponding competence e Follow the lines of this manual e Face this manual as part of the product e Keep this manual over the lifetime of the product e Pass this manual to new owners of the device e Download the latest version of the manual Safety related red flags IMPORTANT Handle with the dangerous electric voltages carefully With this voltage there is the danger to get a life threatening electric shock Always observe After taken the device from a cold room to a warm room it is not allowed to activate the device It is possible that thereby emerged condensed water damages the device Activate the device not until it reached ambient temperature 4 12 VARYTEC Prevent that the power cable has contact with other cables Handle carefully with power cables and power connections Don t touch them with clammy hands Make sure that the voltage which is to connect not exceeds the specified values Make sure that it isn t possible to squeeze or damage the power cable with
Download Pdf Manuals
Related Search