Powermax+ i3048 - A&C Green Energy
Contents
1. same for the negative wire Be sure the polarity is connected properly Length of these two connecting wires should be no more than 3 feet Hand tighten the nuts on each battery terminal until snug Do not over tighten 2 Connect the load to AC OUTPUT Load is defined as whatever is connecting to your appliances so your house circuitry Appliances Generator Battery Bank Typical Off Grid System 5 Operation Before powering up this unit please double check to make sure all connections are proper and secure 1 The IVT switch when lit with the green LED indicates the unit is ON and the inverter is supplying pure sine wave power to the AC OUTPUT terminal on the back panel 2 The inverter is capable of continuously powering AC products that use a maximum of 3kW Because the power or wattage Rating of AC products is the average power they use the initial starting power may exceed the rated power Appliances such as TVs computer monitors and electric motors are examples of products that have high surge requirements at start up Although your PowerMax 3048 inverter can supply momentary surge power twice the power rating there could be occasions when products rated less than their rated watts may still exceed the inverter s surge capabilities resulting in a triggered safety overload shutdown If this problem occurs when attempting to simultaneously operate several AC products first try switching on the inverter2. with all AC products appliances turned off After everything is powered off turn each appliance on one by one starting with the high surge product first 6 Troubleshooting Problem Inverter shutdown and LCD displays HIGH BATTERY Possible Cause 1 Defective batteries or connection 2 Batteries are overcharged Solutions 1 Check battery and connection replace 2 Wait until voltage drops then inverter will start automatically Inverter shutdown and LCD displays LOW BATTERY Batteries are fully discharged Wait until the batteries receive a minimum charge then inverter will start automatically Inverter shutdown and LCD displays OVER TEMP Inverter temperature is too high Inverter will start automatically when internal temperature drops Make sure that the area is well ventilated Inverter shutdown and LCD displays OVER LOAD Power overload Turn off the inverter and check the load Turn inverter back on Fuse Melted 7 Maintenance 1 Batteries connected in reverse polarity 2 The inverter has been damaged 1 Re connect the batteries properly amp replace fuse 2 Contact for repair WARNING DE ENERGIZE THE SYSTEM BEFORE DOING ANY REPAIR OR MAINTENANCE THE INVERTER S CAPACITORS HOLD CHARGE EVEN WHEN THE UNIT IS UNPLUGGED NO WORK SHOULD BE DONE WITHOUT CONSULTING A LICENSED ELECTRICIAN FIRST In order to keep the electric equipment
3. PowerMax 13048 Pure Sine Wave Inverter User s Manual 1 Security IMPORTANT To prevent bodily injury or property damage please follow these instructions precisely With personal safety as a primary focus in design this charge controller has been engineered to function properly and efficiently 1 2 ce Professional installation and guidance is always recommended Otherwise please contact your authorized PowerMax agent before installation Keep the inverter dry Do not clean with a wet or damp cloth This is an electric device and cannot get wet at all Prevent any spills on or near the inverter Keep all children and any person with limited understanding and or decreased mental capacity away from the controller Keep the controller away from direct sunlight or any other heat source Please check the rated voltages of your wind turbine solar panel and battery before connection Their rated voltages all should be the same Pay close attention to the connection of your wind turbine solar panels and batteries to make sure positive goes to positive and negative goes to negative Smaller gauge wires should not be used with higher current equipment Ensure that all component connections are tight and secure DO NOT TOUCH any bare parts on the controller The high voltage can cause lethal shock 2 General Description This PowerMax inverter can convert the batteries DC voltage to reliable pure sine wave AC voltage for sta
4. in the best working condition and preserve its performance we recommend conducting an inspection every 6 months Again please take caution in conducting any maintenance or repair e Remove dust and dirt from the controller and inverter units e Check for any discoloration or deformations of the cable sheaths and components e Check to ensure all cables are taut and terminal screws are still tight e Check to make sure all module housing screws are tight 8 Technical Specifications Model Normal Output Power Normal DC Input Voltage Over Voltage Shutdown Over Voltage Recovery Under Voltage Shutdown Under Voltage Recovery No Load Loss Output Wave Rated Output Voltage Total Harmonic Distortion Output Frequency Dynamic Response Load Capacity Inverter Efficiency Noise Level 1m Isolate Level Protection Type Operation Ambient Temperature Operation Altitude Operation Ambient Humidity Size W x H x D mm Weight KG 13048 3KW 48V Dc 68V DC 66V DC 42V DC 48V DC 5A Pure Sine Wave 120V AC lt 4 60Hz O5Hz 5 120 1min 150 10S 90 lt 40dB 1500V AC 1 min High battery low battery over load short circuit over temperature pole confusion protection for storage battery 10 50 C lt 4000m 0 90 no condensing 470 x 430 x 300 24 5
5. ndard household appliances such as televisions computers water pumps and lava lamps The inverter is designed to provide years of trouble free operation and includes an automatic safety monitoring circuitry to protect the inverter and your batteries 3 Main Features Pure sine wave output can power any household appliance Integrated circuitry uses less wire connection Improved system integration through micro processor technology Excellent protection o over voltage shutdown under voltage shutdown overload protection short circuit protection overheating protection O O OO 4 Connection 1 Selecting a Suitable Location For safe and optimum performance install the inverter in a location that is e DRY Do not expose the inverter to spills or humidity e COOL Operate only in ambient temperatures between 32 F and 104 F Keep away from direct sunlight furnaces heating vents or other heat producing equipment e WELL VENTILATED Allow at least 4 inches clearance above and on all sides of the unit for proper cooling and air circulation e SAFE Do not install the inverter in a compartment with flammable liquids or explosive vapors e CLEAN Keep the inverter clean and free of dust and or dirt This is especially important if the inverter is used in an industrial work environment 2 Power Connection iy Using16mm electrical wiring connect the battery s positive pole to the positive battery terminal on the inverter and the
Download Pdf Manuals
Related Search