Home

Now - Tonaro Go Karts Online

1. 13 Tonaro SA warrants this go kart to be free of manufacturers defect for a period of 60 days from the original date of purchase 14 This warranty does not cover wearing of parts including but not limited to the clutch tyres and brake pads 15 This warranty does not cover damage or failure due to inadequate maintenance or neglect by owner 16 This warranty does not cover physical damage or failure due to overloading misuse or reck less operating behaviour 17 This warranty is available to the original purchaser 18 If there is a defect in workmanship or material during the warranty period we will repair or replace 19 This warranty does not cover normal wear and tear damage caused by abuse or neglect overheating or overloading corrosion unauthorised modifications or alterations damage caused by incorrect fuel oil or lack of it consumables including tyres spark plugs bearings brake pads clutch assembly brake or throttle cables air filter If the product requires repair inspection by an approved authorised dealer or mechanic it is the customer s responsibility to deliver the product to the place of repair inspection and to arrange for collection If the repair fault is not covered by warranty the customer shall pay for all costs related to the repair and inspection 13 TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE ACTION SOLUTION Engine Stops and won t 1 Bad coil assembly Replace coil cap start E
2. Please view DVD for detailed instruction We have made a list of some handy tips to assist you with assembling your Go Kart Firstly connect the front frame with the middle frame Bolt securely Connect the rear frame and suspension springs to main frame Connect rear frame loosely as later you will need to bolt the seatbelt here We recommend using lock tight as the nuts can become loose over time with the vibration Regularly check and tighten nuts and bolts Check pre assembled nuts and bolts as these have been found to be loose It is the buyers responsibility to check these are all secure before using the go karts Connect steering column and fully extend to the highest position Tighten collar clamps using larger allen key provided Connect hydraulic brake handle to left steering Use smaller allen key provided to tighten handle bracket Fig 8 Keep cable on inner side of the outside frame amp between the wishbone below steering Make sure you remove small black plastic tongue on the brake handle Use a pair of nose pliers to remove this Release throttle cable amp on off wiring cable on steering Run through wishbone of steering with brake cable Run cables along brake side of go kart keep on the inner edge of frame Fig 5 Connect the on off switch wiring running from steering to the earth on the petrol tank Fig 6 The air filter needs to be removed before attaching throttle cable to lever on motor Undo both wing nuts to rem
3. kart correctly and added correct amount of oil to the engine and wet clutch unit Fig 6 On off switch wiring connected to earth below petrol tank Fig 5 Brake 8 throttle cables on steering assembly Fig 7 Position of Throttle cable on motor Remove air filter to attach Fig 8 Hydraulic brake clamp attachment to steering wheel Use allen key to tighten SAFETY RECOMMENDATIONS PLEASE FOLLOW THESE INSTRUCTIONS Spend time and explain carefully to young children and inexperi enced riders how to operate go karts Drivers under 16 years of age must only operate the go karts with the permission of their parents guardian Younger children should be accompanied by an adult at all times This applies to participating and non participating persons Children under 16 years of age must always be closely and actively supervised Never permit anyone to operate the go kart without proper instruc tions Ensure seatbelts and safety helmets are ALWAYS worn Explain clearly use of the throttle and brake handle and the kill switch Always make a pre operation inspection before you start the engine This is essential and may prevent an accident or equipment damage It is advised to place the rear of the kart on blocks so the wheels spin freely to enable you to check controls adequately Once the engine has been started go over all controls and ensure they are operating effectively and make adjustments accordingly Allow eng
4. 2 Air cleaner is dirty and Clean shake all dust out dusty Ea Replace Never run engine without air cleaner Go Kart moving or 1 Throttle cable engaged Check for kinks Ensure the inner creeping forward or wire cable is moving freely within wanting to take off the black casing Check the throttle lever is spring ing back to off position 12 PLEASE NOTE These Go Karts are not designed for 4WD Tracks steep hills rocky or very uneven terrain They are essentially a grass drift go kart Damage may occur when used in unsuitable terrain amp we hold no liability if the go kart is not adequately maintained or used inappropriately Please do not tow with these karts as clutch may overheat and cause damage Running the karts for long periods of time at low revs can also cause damage to the clutch Although the karts can be easily governed for younger children or inexperienced riders this should only be a temporary adjustment Please ensure all bolts nuts including pre assembled parts are tight and secure before use Check on a regular basis especially during the running in period as they can vibrate loose We recommend lock tight for extra security especially when go kart is used on uneven terrain Fig 4 Ultimate Drifta Go Kart 200cc Roll Cage Steering assembly Seatbelt attachment Rear frame Front frame Mid Frame Front tie rods Leg amp foot protector bars 10 11 12 ASSEMBLY INSTRUCTIONS
5. ASSEMBLY INSTRUCTIONS USER MANUAL WWAW gokactsonline c0 za GO KART REGISTRATION To be recorded at original date of purchase PURCHASER Name amp Address DATE OF PURCHASE GO KART ID CODES MODEL NO ENGINE NO Imprinted in engine case behind seat FRAME NO Located on rear frame near brake COLOUR CONGRATULATIONS You are now the proud owner of a Drift Go Kart Remember This is a motorised vehicle and not a toy If instructions are not followed there is a possibility of personal injury or equipment damage SPARE PARTS LIST Front Connecting Arms L H and R H Short tie rod Long tie rod Front wheel hub Dust cap Steering wheel Steering column Steering column with fittings Bottom plate Steering Handle assy complete Throttle handle Brake handle Throttle cable Kill switch wiring Kill switch on off Clutch Centrifugal Clutch spring Carburetor Shock absorber Pull start Wheel rim drift go kart Wheel rim caged go kart Tyres caged Drift tyres amp rims complete Hydraulic brake unit complete Hydraulic brake pads Hydraulic brake bracket 15 IMPORTANT PLEASE READ CONDITIONS OF USE SAFETY DISCLAIMER All our karts are off road leisure go karts and as no safety standards are available driving is at your own risk Neither the manufacturer Tonaro SA sales agents or distributors are liable for personal or other damage neither to participating or non participat ing p
6. ars and connecting bar between the two onto front frame Line up holes and place bolts washer attach bolts loosely Add remaining frame and connect to back frame Bolt and tighten all bolts Double check all bolts on the roll cage are tight and attached to main frame Wrap padding around roll cage and cable tie in place Cover with sun cover Place seat on and attach harness seat belt to main frame Ensure tyre pressure is at 18 20 psi in all tyres Do not let down This may result in the rims digging in to the ground when cornering and the kart rolling Fill engine with approximately 600ml oil 20W50 or 10W40 Fill from behind the seat Fill Wet Clutch with correct type and amount of oil Oil Capacity 300ml Recommended Oil Castrol 4T 10W 40 part synthetic based If insufficient oil is added the clutch will be damaged Fill with 95 unleaded petrol To Start Ensure Fuel lever on set choke to on position Once started move choke into run front position When starting go kart for the first time it may be necessary to pull the starter handle 4 5 times Do not allow pull start to snap back Return it gently to prevent damage to the starter After engine is started let it warm up for 2 3 minutes before riding Please take the time to ensure the go kart has been assembled correctly and all controls are operating correctly Please view DVD prior to assembling and using your go kart This will ensure you have assembled your go
7. ersons At delivery the owner takes full responsibility for the kart and use ofthe kart The owner at time of purchase assumes all risks associated with the use of the go kart and agrees to these terms of use Ensure that the person driving is of an age size and has the necessary skills and experience to drive the kart safely Ensure that the go kart is used in the appropriate environment and condi tions present allow safe operating of the go kart to the driver and all non drivers These go karts are not designed for jumping racing or performing any ab rupt spin out manouevres They are not designed for steep or uneven terrain or for use on public roads Please use on safe terrain which you are familiar with Failure to adhere to these warnings may result in accidents and serious injury Drivers under 16 must do so only with the permission of their parents guardian Younger children must be accompanied by an adult at all times Please refer to Drift 2 User Manual and Engine Owners Manual supplied by manufacturer for additional information and trouble shooting 14 Thank you for Buying a Drift Go Kart from Tonaro SA PLEASE read all instructions and manuals prior to assembling go karts PLEASE ensure you watch DVD provided either on your computer or dvd player Please continue reading user manual so you understand the go kart to ensure many years of safe and fun family enjoyment Troubleshooting chart is located a
8. ine to warm up for up to 2 or 3 minutes before riding to help prevent spark plug fouling up Check brake and throttle cables are adjusted correctly and there are no kinks Ensure ALL bolts and nuts are tight and secure Check regularly Check tyre pressure regularly Recommended tyre pressure is18 20 psi
9. nstructions will not be cov ered by warranty 2 After assembling please retighten all nuts and bolts and double check all parts are secure and operating correctly 3 Before starting the engine ensure correct type and quantity of engine oil and wet clutch oil has been used 4 Oil the chain with chain lube before use and on a regular basis Follow all maintenance instruc tions 5 Use unleaded 95 fuel only 6 Once the engine has been started allow to warm up for 2 3 minutes before test driving 7 Do not allow the engine to operate at low revs as this may overheat and damage the clutch This warranty does not cover damage to the clutch through overheating Over heating may be caused by incorrect driving habits such as driving too slowly revs too low stop and go driving driving with the brake engaged and restricting the throttle Driving in confined or limited areas will damage the clutch 8 Test ride and notify us immediately if there is a fault found with the go kart 9 Do not attempt to do any repairs without contacting us first as this will void warranty 10 We will replace parts that are damaged or defective 11 Product warranty does not cover damage due to misuse or abuse 12 The warranty is voided if the go kart is modified in any way overloaded leased or rented Also if improperly maintained serviced or repaired Any damage due to accidents or through negli gence used to perform stunts jumps or any other misuse
10. ove unit Run throttle cable to lever on back of motor Remove small screw on bolt Carefully insert cable wire through hole Replace screw amp tighten screw to hold cable wire in place Be careful not to damage wire inner cable as this needs to move freely Fig 7 Use cable ties to neatly tie to frame Make sure all cables are free of acute an gles amp operate freely Roll cage assembly Unwrap all framing extra bolts and padding Place bolts nuts in a neat pile 6 TROUBLESHOOTING GUIDE PROBLEM Engine Stalls Engine backfires Running Poorly Hard to Start Cuts Off Chain Falls Off Difficulty Braking Making Grinding noise Kill switch not working POSSIBLE CAUSE 1 Spark Plug fouled carbon deposition 2 Fuel too low 3 Make sure kill switch is not engaged 4 Check choke to see if it is open Too much choke will flood engine 5 Fuel line hose 1 Chain Sprockets not aligned 2 Chain too loose 3 Excessive chain wear or stretch 1 Brake pads worn out 2 Hydraulic brake fluid low 1 Kill switch wire plug in con nector separated at the en gine 2 Wire end terminal has come loose from the engine 11 ACTION SOLUTION Clean spark plug Install a new spark plug Recom mend BPRSES Fill fuel tank min 1 3 Do not over fill Check fuel switch is on If motor is warm you will not need choke Check spark plug is not wet from the petrol flooding the plug You ma
11. t the back of this manual see engine manual for engine maintenance and inspection CAUTION BEFORE USE Please ensure you add engine oil to the engine oil reservoir These engines are four stroke You must also add oil to the clutch reservoir see image below Engine oil capacity 600ml Use Castrol GTX 20W50 The engine oil reservoir is lower to the ground than the wet clutch reservoir and has a small dipstick Clutch oil capacity 300ml Recommended oil for clutch Castrol 4T 10W 40 These go karts have a wet clutch so require oil to be added to clutch The wet clutch unit is closest to the chain guard and has the larger dipstick Fig 1 Wet clutch reservoir Add 300ml oil PETROL We recommend 95 unleaded Do not overfill petrol tank NEVER MIX FUEL and OIL If transporting your go kart turn the fuel valve off to prevent spillage and engine flooding Fig 2 Oil for Engine 600ml Castrol GTX 20W50 Pennie EVERYDAY PLUS Oil for Engine 10W 30 or 10W 40 600m Fig 3 Oil for Clutch 300ml id Castrol 4T 10W 40 POWER GPS WARNING The exhaust becomes hot during operation and re mains hot for a while after stopping the engine Be careful not to touch while it is hot Ensure children are aware of this Please supervise to prevent severe burns WARRANTY 1 Please read manufacturers handbook and all instructions supplied by Tonaro SA before assembling your go kart Damage caused by failing to follow correct i
12. y need to dry the plug out or replace Make sure fuel line has no kink re Align Sprockets Check sprocket on clutch and bolt holding clutch onto shaft Adjust chain tension Motor may need sliding back on adjustable mount Replace chain Replace brake pads Check connection Push together Re install or tighten screw holding wire end to engine case 10 11 12 MAINTENANCE PROCEDURES Please also refer to and follow manufacturers instructions Please refer to engine manual for engine maintenance and inspection After use clean wash the go kart and regularly use WD40 or CRC This will enable you to examine your kart for any potential problems or adjustments that need to be made Clean air filter regularly from dust Keep chain lubed Spray with chain oil regularly Lubricate wheel bearings and moving parts regularly To drain oil there is a sump bolt at the back and under the motor Do not allow the engine to operate at low revs for long periods as this may over heat and damage the clutch Ensure wet clutch contains sufficient oil or else damage will occur We recommend NGK sparkplugs BPRSES or BPR6ES Please take care of your go kart 10 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 Place back frame on Bolton loosely as this is where one point of the safety harness will be attached at the end of assembly Position left and right front upright b

Now - Tonaro Go Karts Online

Contents

Download Pdf Manuals

Related Search

Related Contents