PDi-P15X with Computer - PDi Communication Systems
Contents
1. Communication Systems Inc y Quick Start Guide PDi P15X with Computer Support Arm Mounted Television Document Number PD196 143R3 PDi Communication Systems Inc 40 Greenwood Ln Springboro OH 45066 WWW pdiarm com Toll free 800 628 9870 Fax 937 743 5664 PDI Communication Systems inc MODEL NUMBER Document Number PDI P15X WITH COMPUTER Better Solutions Are Within Reach WARNINGS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user of the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to This symbol is intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance NOTE TO CABLE TV INSTALLER This reminder is provided to call the cable TV systems installer s attention to Article 820 40 of the National Electrical Code The code provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of the cable entry as practical FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when t2. 1 Press the SETUP button on the remote control 2 Press A or to highlight Channels 3 Press to enter the Channels sub menu Signal Cable STD Auto Program Add Delete Channels Clear Service Level Copy Service Level Parental Control Power on Channel Channel Lock Disabled Channel Memory Override Enabled Service Level Picture Sound Channels Features OSD Language Sources FM RADIO Position A Position a Exit SETUP Next lt gt Exit SETUP Next lt gt PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 DX a MODEL NUMBER Document Number HI PDI P15X WITH COMPUTER Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 6 of 12 SIGNAL Four different tuning types are available depending upon the healthcare facility s signal type Air Cable STD Cable IRC or Cable HRC Selection of the correct signal type is required for the TV to recognize all possible channels and before Auto Programming can begin 1 In the Channels menu press A or Y to highlight Signal 2 Press lt or gt to select Air Cable STD Cable IRC or Cable HRC NOTE Most hospitals use the Cable STD signal type 3 Now perform Auto Program to add channels Auto Program The TV automatically scans each available channel for activity Channels that display activity are memorized into the selected Service Level 1 Inthe Channels menu press A or Y
3. page 8 A Cloning Main Menu will appear Press A or to highlight Restore Settings to TV Press to display a list of previously stored TV setups on the USB thumb drive Press A or to highlight the desired setup file Press gt to select it A confirmation screen will appear Press A to restore the selected setup file or press lt to return to the previous menu without restoring A progress screen will appear as the settings are restored The TV will return to normal viewing mode after restoring is complete o DEE p PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 bX m MODEL NUMBER Document Number HT i PDI P15X WITH COMPUTER _ PD 196 143R3 Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 9 of 12 Cloning Main Menu Restore Settings To TV Restore Settings to TV m P15X_ tdf Save Settings to USB Upload Firmware to TV Information Position A Next gt Position Y COMPUTER This P15X contains a full functioning computer module running Windows XP Enabling Disabling PC Analog setting The TV s PC Analog setting needs to be enabled before the computer can be booted From the SETUP menu in TV mode press the A or V button to select Source Press to enter Press A or V to highlight PC ANALOG Press lt or gt to select Enabled APO or Enabled No APO NOTE Enable APO Auto Power Off means the TV will turn off if th
4. setup as the Administrative account The computer will boot into a default account user This account has no restrictions imposed on it It is recommended that Microsoft Steady State be installed to assist in imposing further restrictions on public accounts For more information on using Microsofts Steady State program please see the help document installed with Microsoft Steady State NOTE The user account does not have a password The pdi user account has a password computer123 Connection ports The computer board for the P15X has several ports to connect hardware See the picture below for a description Serial USB 2 Ethernet PS 2 Ethernet VGA USB ports You may connect different tyoes of hardware to either of these two ports such as mice keyboards and MP3 players External CD DVD ROM drives may also be connected so software can be installed and media accessed Ethernet The two Ethernet ports are identical Either one may be used to connect to a local network WiFi Many P15X models are equipped with 802 11n for wireless networking capabilities Turning off computer Windows XP will go through a shutdown process automatically when the TV is turned off Before pressing the power button check to be sure the computer is set to shut down when the power button is pressed Use these steps to check this In Category View 1 Click the Start button Click Control Panel Click Performance and Maintenance at t
5. to highlight Auto Program 2 Press to select Auto Program 3 On Mode press lt or gt to set the scope of channel scanning Analog Only TV searches for analog channels only Digital Only TV searches for digital channels only Analog and Digital TV searches for both analog and digital channels 4 Press A or to highlight Channel Sequence 5 Press lt or gt to set the Channel Sequence in which the channels are displayed Interleave A D In the order of channel number regardless of the system All A then D All digital channels are displayed after all analog channels 6 Press A or to highlight the Service Level Free Basic or Premium you wish to program The menu displays the current programming status of each level as either Programmed or Blank NOTE A programmed service level can also be reprogrammed if desired 7 Press to start auto programming 8 A confirmation menu will appear before proceeding Press A to start auto programming Press W to cancel the operation The TV now will search all available channels Auto programming requires several minutes to complete NOTE Digital channel auto programming may take longer than 10 minutes to complete 9 See the Sound section to enable internal speakers Signal Cable STD Mode Analog Only Auto Program Channel Sequence Interleave At D Auto Delete Channels Free Programmed Clear Service Level Basic Blank a Copy Service Level Premium Blank Parental Contro
6. 5 pounds The single coaxial cable on top of the TV is used to supply either low voltage AC or DC power 18 to 32 Volts and the RF signal to the television iN DANGER ARM RECOIL HAZARD The safety brake pin must remain in the SAFETY BRAKE PIN HOLE whenever the television is removed from the arm or when the arm is removed from the wall bracket to prevent the arm from springing open Remove and save the Retainer Bolt and Lock Washer from the TV s swivel Remove the two Nose Cover Retainer Screws and raise the metal nose cover Slide the TV s swivel completely into the arm s clevis slot such that the Upper and Lower Swivel Plates sandwich the arm s nose The nose of the support arm should rest between each plate Align the Retainer Plate s mounting hole over the arm mounting hole Thread the Retainer Bolt with Lock Washer through the Upper Retainer Plate the arm s nose and then into the Lower Retainer Plate Tighten The coax cable in the nose of the arm should be joined with the coax cable from the television Tighten the connection with a wrench and cover it by sliding the plastic boot sections into mating position WARNING Tightening this cable connection only with your fingers will result in reliability problems weeks or months later Because the TV draws its power current through this connection eventually the finger tightened connection will loosen due to thermal cycling develop
7. TER Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 8 of 12 5 Press A or YW to highlight Save Settings to USB 6 Press to display the Save Settings to USB menu Cloning Main Menu Save Settings To USB Restore Settings to TV m Save Save Settings to USB m P15X_ tdf Upload Firmware to TV u Clear Filename Information Position AV Next gt Back lt 4 Position Next gt 7 Ifyou want to rename the file press the A or VW to highlight the file name Otherwise go to step 7 a Press lt or gt to highlight each character b Press A or V to change each character c Repeat this process until you have the desired file name Up to 8 characters may be used d Press lt or gt to exit out of the characters 8 Highlight Save 9 Press to download the TV s setup to the USB thumb drive A progress screen will be displayed 10 A confirmation screen will indicate completion of the saved file Press gt to start the process Press lt to return to cancel 11 After the settings are saved press lt to return to the Cloning Main Menu 12 Remove the USB drive to return to normal TV operation Save Settings To USB Settings saved from TV to P15X __ tdf file in USB Back 4 Next P Restore Setting to TV This allows you to upload settings you saved on the USB thumb drive from another P15X TV 1 Insert the USB thumb drive into the cloning port in the back of the TV See connector diagram on
8. Volume TV Free Service Level Enabled Power on Volume TV Basic Service Level Enabled Internal Speaker Enable TV Premium Service Level Enabled HDMI Audio Port Composite Video HEL m Composite S Video S Video arte te Sound Mode Component Enabled Headphone Sound Mode HDMI Enabled PC ANALOG Enabled FM RADIO Enabled ee ee Position AV Position AV Exit SETUP Exit SETUP CLONING Cloning allows quick programming of a TV from a USB thumb drive Clone operation involves first downloading setup information from a programmed host TV to a thumb drive and then uploading the setup information to another TV Cloning can also be used to re program a TV Save Settings to USB 1 Using a computer create a folder titled PDITDF on a USB thumb drive 2 Remove 3 screws from back access cover and remove cover from TV 3 Turnon the TV 4 Insert the USB thumb drive into the cloning port in the back of the TV See connector diagram on page 8 A Cloning Main Menu will appear ae lt Access cover screws saeee eee ee Se 2 eB eee DD E S a D O O O O O A R See eee eeese2222 22 2 e tE Ses SS SSSSescoe2e2e2e2ee 2s het SPP PPP PP eee eT e eee eee 3 e On cema IN w iota TFT TLL e r e COMPOSITE COMPONENT S VIDEO IN omy PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 DX a MODEL NUMBER Document Number HT PDI P15X WITH COMPU
9. ck the calibration target to calibrate the touch screen Administrator Access is Required Configure Test Configure the calibration type Test touch screen calibration d offset oc Ce to NOTE f you are not able to access the Hampshire TSHARC Control Panel with the touch screen A interface use a mouse to access it Once the Hampshire TSHARC Control Panel is launched calibration should start automatically within a few seconds Restoring Windows to Factory Default If the operating system becomes corrupt it can be restored to factory defaults Warning This process will destroy all data and settings on the disk It cannot be undone 1 Attach a USB keyboard to the computer Turn on the computer and within the first 5 seconds select Boot Recovery Image At the login prompt enter username pdisystem and password computer1 23 Click Login If the username and password are accepted then click Start System Restore Process Follow the prompts to continue the restoration process After the computer reboots it will be reset to factory defaults ee eS Additional Information Additional information is available in the user manual Please visit the company web site at www pdiarm com or contact the office Request document number PD196 135 PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 bX
10. emote have correctly mounted the TV and connected the coax cable that provides both Power and RF signal SERVICE LEVELS The P15X contains four separate Service Levels allowing the hospital to offer either basic or enhanced viewing The current service level can be quickly determined by accessing the Setup menu using the programming remote control The service level can be changed to any of the 4 levels at any time by entering the Setup menu and changing the Service Level menu items Service Level Picture Sound Channels Features OSD Language Sources FM RADIO Position A Y Exit SETUP Next lt gt Disabled is like a mechanical key lock when in Disabled service level the TV can be turned OFF and ON but cannot be used for viewing A standard message appears on a black screen Free lets patients watch hospital education and information channels without renting the TV The channels containing programming for no charge are typically programmed into this level of service This is the factory default setting for Service Level Basic service typically allows additional channels beyond those offered in the FREE level Premium is the highest Service Level with typically the most channels available for viewing CHANNELS The Channels menu allows you to program different signal sources into three of the Service Levels Free Basic and Premium and to add or delete individual channels Only one Service Level is usable at a time
11. ere is no image To exit press SETUP button until the Programming menus disappear TV Enable APO Composite Video Enable APO S VIDEO Enable APO Component Enable APO HDMI Enable APO PC ANALOG Enable APO FM RADIO Enabled al ae pi Power On Source Last Position Y Exit SETUP Initial setup 1 Be sure the PC ANALOG source is enabled See the Enabling Disabling PC Analog setting section 2 To switch from television to computer mode press the AV button located on the right side of the control panel between the Channel Up Down and Power buttons 3 Windows will automatically boot to the desktop 4 f using a touch screen go to page 11 PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 bX a MODEL NUMBER Document Number DI PDI P15X WITH COMPUTER Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 10 of 12 A NOTE The P15X does not come with virus protection software preinstalled PDi Communication Systems Inc strongly recommends installing virus protection software NOTE Default user accounts are not restricted in any way PDi Communication Systems Inc strongly recommends creating a user account with limited privileges NOTE Be sure that automatic Windows updates are enabled as well as Windows Firewall to help protect against Internet threats Understanding Default Computer Accounts A pdi user account has been
12. ess the power button on my computer Shut down v NOTE A forced shutdown will occur 2 minutes after turning off the TV if Windows has not automatically A shut down before then Touch screen Calibration If your P15X is equipped with a touch screen it may need to be calibrated 1 Goto the All Programs menu under Start 2 Select Hampshire TSHARC Control Panel from the menu FA Activate Windows My Bluetooth Places Set Program Access and Defaults S Windows Catalog 4 Internet 5 Internet Explorer b Windows Update va J E mail R Accessories Outlook Express a Games F Realtek MSN F Realtek Sound Manager Windows Media Playa Startup Wi Hampshire TSHARC Control Panel 33 Windows Messenger 4 Internet Explorer MSN Tour Windows XP My Bluetooth Places F Files and Settings Tr A Outlook Express amp D wizard Remote Assistance it pal Aor TSHARC d windows Media Player ane 33 Windows Messenger F windows Movie Maker Log Off oJ Turn Off Computer All Programs PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 o lt m MODEL NUMBER Document Number I i PDI P15X WITH COMPUTER Better Solitions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 12 of 12 3 Select the calibration tab and follow the on screen instructions Hampshire TSHARC Control Panel Rev 6 20cs Touch for cli
13. he bottom of the first column of icons Under the or pick a Control Panel icon section click Power Options Select the Advanced tab in the Power Option Properties window If it is set then Shut down will appear in the When press the power button on my computer dropdown menu in the Power buttons section If Shut down is not the selected item then select it from the dropdown menu Click OK 8 Close out of all open windows AaRWN o PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 o lt a MODEL NUMBER Document Number HT PDI P15X WITH COMPUTER Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 11 of 12 In Classic View 1 Click the Start button 2 Click Control Panel 3 Click Power Options Icon 4 Select the Advanced tab in the Power Option Properties window 5 If it is set then Shut down will appear in the When press the power button on my computer dropdown menu in the Power buttons section If Shut down is not the selected item then select it from the dropdown menu Click OK 7 Close out of all open windows 2 Power Options Properties Power Schemes Advanced Hibemate UPS el h Select the power saving settings you want to use Options C Always show icon on the taskbar Prompt for password when computer resumes from standby Power buttons When pr
14. he equipment is operated in a residential or commercial installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help SAFETY INSTRUCTIONS INSTRUCTIONS Be sure to read follow and keep these instructions Heed all the warnings MAINTENANCE AND SERVICING Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped gt gt Pr gt F amp F PF A SUPPORT ARM MOUNTED TELEVISION Page 2 of 12 Never remove the back cover of the TV this can expose you to high voltage and other hazards If the TV does not operate properly unplug it and call an authorized service center or PDI CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing othe
15. his manual PDI Communication Systems Inc make no representation or warranties with respect to the accuracy or completeness of the contents of this manual and specifically disclaim any implied warranties or merchantability or fitness for any particular purpose and shall in no event be liable for any loss of profit or any other damages The information contained herein is believed to be accurate but is not warranted and is subject to change without notice or obligation TRADEMARKS Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories All other brand names and product names used in this manual are trademarks registered trademarks or trade names of their respective holder PDI and Better Solutions Are Within Reach are registered trademarks of PDI Communication Systems Inc Springboro Ohio PRODUCT ACCESSORIES Not Included with TV Programming Remote PD108 420 Support Arm PDI 508C 12 Wall Bracket Power Supply PDI 771B PDI 771CA Central Power Supply PDI 772HE Individual Power Supply PDI 750A PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 bX PDI Communication Systems inc Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 4 of 12 INSTALLATION ON SUPPORT ARM The PDI P15X television is designed to attach to a wall mounted suspension arm capable of supporting a television weighing 1
16. l Power on Channel Channel Lock Disabled Channel Memory Override Enabled Position YT Position Exit SETUP Exit SETUP SOUND The Sound sub menu allows very precise adjustments of several sound parameters 1 Press the SETUP button on the remote control 2 Press A or to highlight Sound 3 Press gt to enter the Sound sub menu PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 bX a MODEL NUMBER Document Number HT PDI P15X WITH COMPUTER __ PD 196 143R3 Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 7 of 12 Service Level Minimum Volume Picture Maximum Volume Sound Power on Volume Channels Internal Speaker Enable Features HDMI Audio Port OSD Language English Composite S Video Sources gt Sound Mode FM RADIO gt Headphone Sound Mode Position AV Position AV Exit SETUP Exit SETUP Internal Speaker Enable The speakers inside the TV s cabinet can be turned on or off for each TV Service Level NOTE Sound to the earphone jack remains on at all times In the Sound menu press A or F to highlight Internal Speaker Enable Press gt to enter it Press A or to highlight the Service Level Free Basic or Premium you want to enable Press lt or gt to select Enable Press SETUP to return to the previous menu To exit press SETUP until the programming menus disappear Minimum Volume Speaker Maximum
17. lug must remain readily operable CAUTION Unplug this apparatus during lightning storms or when unused for long period of time PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 DX m MODEL NUMBER Document Number I i PDI P15X WITH COMPUTER Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 3 of 12 PRODUCT MODIFICATION DO NOT attempt to modify this product in any way without written authorization Unauthorized modification could void the user s authority to operate this product OVERHEAD FALLING HAZARD WARNING To prevent injury this apparatus must be securely attached to the wall in accordance with the installation instructions TVs can pose a striking hazard when mounted at an elevated position OTHER EQUIPMENT Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus Use caution when moving the cart apparatus Only use attachments accessoriesspecified by the manufacturer Copyright Disclaimer amp Trademarks COPYRIGHT PDI Communication Systems Inc claims proprietary right to the material disclosed in this user manual This manual is issued for user information only and may not be used to manufacture anything shown herein Copyright 2009 by PDI Communication Systems Inc All rights reserved DISCLAIMER The author and publisher have used their best efforts in preparing t
18. r than contained in the operating instructions unless you are qualified to do so POWER CORD Protect the power cord from being walked on or pinched particularly at the plugs convenience receptacles and the point where they exit from the apparatus CAUTION Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two plates and a third grounding prong The wide blade or the third prong is provided for your safety If the plug does not fit into your outlet consult an electrician RAIN AND MOISTURE WARNING To avoid the hazards of fire or electrical shock DO NOT expose this television to rain or moisture INSTALLATION DO NOT block any ventilation openings Do not install near any heat source such as radiators heat registers stove or other apparatus including amplifiers that produces heat WET LOCATION Apparatus SHOULD NOT be exposed to dripping or splashing Objects filled with liquids such as vases SHOULD NOT be placed on the apparatus OXYGEN ENVIRONMENT WARNING DO NOT use in any oxygen tent or oxygen chamber Such use may cause a fire hazard CLEANING AND DISINFECTION Clean the exterior of this television by removing dust with a lint free cloth CAUTION DO NOT use abrasive or chemical cleaning agents Clean only with a dry cloth DISCONNECTING DEVICE FROM MAINS Main plug is the disconnecting device The p
19. resistance and prompt a service call Tighten all F fitting connections with a wrench 6 For PDI 500 series arms remove the Safety Brake Pin from the Safety Brake Pin Hole reattach the acorn nut to the pin and store the assembly inside the nose of the arm by attaching it to the coax cable using the attached plastic clip For PDI 405 series arms remove the Safety Brake Pin from the Safety Brake Pin Hole and install thru rear mounting holes of the nose cover Securely tighten DO NOT store the pin inside the nose of PDI 405 series arms Close the metal nose cover onto the nose Reinstall the two Nose Cover Retainer Screws MODEL NUMBER Document Number PDI P15X WITH COMPUTER Brake Pin Hole Nose Cover Retainer Screws Dam Mounting Hole Retainer Bolt Lock Washer Note Slide boot to cover exposed connector after the connection is made Upper Retainer Plate Lower Retainer Plate PDi Communication Systems Inc 40 Greenwood Lane Springboro Ohio 45066 USA PH 800 628 9870 FX 937 743 5664 o lt a MODEL NUMBER Document Number HT PDI P15X WITH COMPUTER Better Solutions Are Within Reach SUPPORT ARM MOUNTED TELEVISION Page 5 of 12 PROGRAMMING The P15X is programmed by a series of menus that can be accessed with a programming remote part number PD108 420 The following instructions explain how to quickly set up the P15X NOTE The instructions assume you have a programming r
Download Pdf Manuals
Related Search