IcomIC-F1810-2810 UserGuide
Contents
1. J ooa es BASIC OPERATION 2 E Receiving and transmitting Receiving Push O to turn the power ON Push CH Up or CH Down or rotate CH Up Down to select a channel in sequence When receiving a call adjust the audio output level to a comfortable listening level Transmitting Wait for the channel to become clear to avoid interference Take the microphone off hook e 5 tone mute may be released The audible condition is select ed and BUSY indicator lights green e A priority channel may be selected automatically Wait for the channel to become clear e The channel is busy when BUSY indicator lights green Push CALL when initiating a call from your side e Coded audio may be heard from the transceiver then 411 appears e This operation may not be necessary depending on your signal ing system Ask your dealer for details While pushing and holding PTT speak into the micro phone at your normal voice level Release PTT to receive Y IMPORTANT To maximize the readability of your signal 1 Pause briefly after pushing PTT 2 Hold the microphone 5 to 10 cm from your mouth then speak into the microphone at a normal voice level BQ S 2 BASIC OPERATION Transmitting notes e Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions The channe2. O 1 PANEL DESCRIPTION RE DIAL KEY Push to transmit the last transmitted DTMF code CALL KEYS Push to transmit a 5 tone BIIS ID code eCall transmission is necessary before calling another station depending on your signalling system Call A and or Call B may be available when your system employs selective Individual Group calls Ask your dealer which call is assigned to each key EMERGENCY KEYS Push and hold to transmit an emergency call When Emergency Single Silent or Emergency Repeat Silent is pushed an emergency call is transmitted without a beep emission and LCD indication change e H you want to cancel the emergency call push or push and hold the key again before transmitting the call e The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre setting BIIS PMR operation only SURVEILLANCE KEY Push to turn the surveillance function ON or OFF When this function is turned ON the beep is not emitted and the LCD backlight does not light when a signal is received or a key is pushed etc TX CODE ENTER KEY Push to enter the ID code edit mode directly for both 5 tone and BIIS Then set the desired digit using CH Up CH Down or 10 keypad p 11 IC F1810 or IC F2810 only TX CODE CHANNEL SELECT KEY sr Push to enter the ID code channel selection mode directly Then set the desired channel using CH Up CH Down p
3. W RER Wd l A NOTE Use the terminals as shown below for the cable connections Crimp A CAUTION NEVER remove the fuse holder from the DC power cable IC F1810 or IC F2810 only IC F1710 and IC F2710 has a built in speaker MICROPHONE HANGER Connect the supplied mi crophone hanger to the vehicle s ground for mi crophone on off hook functions See p 2 OPTIONAL CABLE OPC 617 Connect an external mo dem unit dimmer control etc 4 CONNECTION AND MAINTENANCE E Supplied Accessories Microphone IC F1810 F2810 only Microphone hanger and screw set ER gl Ww f Speaker Key cap P2 P 2 p Flat washers eene Spring washers CEOE Eo Nuts eeee Microphone hanger cable SS Function name stickers Bracket bolts eee Mounting screws M5x12 HR Self tapping screws M5x16 a e Function name stickers There are no names on the programmable function keys since the functions can be freely assigned to these keys Attach the supplied function name stickers as below to the appropriate keys for easy recognition of that key s assigned function Then protect the attached stickers from unsticking with the supplied key cap as below E Mounting the transceiver The universal mounting bracket supplied with your transceiv er allows overhead mounting e Mount the transceiver
4. When no record is available Y ETE r Push Up or Down or rotate DIAL to select the desired call Push P1 Digital for 1 sec again to return to the standby condition eWhen no operation is performed for 30 sec the transceiver returns to the standby condition automatically 3 BIIS OPERATION E Transmitting a call A total of 3 ways for code selection are available selecting the call code from memory entering the call code from the keypad and calling back from the queue channel record Using call memory While in the standby condition push P1 Digital to enter the call code memory channel selection mode see appears Appears Push Up or Down or rotate DIAL to select the desired call code 3 Push PO Call or PTT to call PTT call can be made only when PTT call capability is permitted ZY NOTE When no answer back is received the trans E ceiver repeats the call 3 times default automatically Y is displayed during each call However an g error beep sounds and is displayed when no Z answer back is received after the calls MMA Push PTT to transmit release to receive Push P4 Moni Audi to send the Clear down signal Q Calling back from the queue channel While in the standby condition push P1 Digital for 1 sec to enter the queue memory channel selection mode Push Up or Down or rotate DIAL to sele
5. 10 During ID code channel selection mode push for 1 sec to enter the ID code edit mode for 5 tone and BIIS Then set the desired digit using CH Up CH Down or 10 keypad p 11 IC F1810 or IC F2810 only ye TX CODE CHANNEL UP DOWN KEYS Push or Rotate to select a TX code channel directly Rotate when this function is assigned to DIAL ID MR SELECT KEY Recalls detected ID codes Push this key then select the ID code using CH Up CH Down Up to 5 ID s are memorized Push and hold to erase the selected D s SCRAMBLER KEY Push to toggle the voice scrambler function ON and OFF COMPANDER KEY Push to toggle the compander function ON and OFF The compander function reduces noise components from the transmitted audio to provide clear communication HOOK SCAN KEY When the hook on scan function is turned ON push this key to stop scanning temporarily Push this key again to re start scanning USER SET MODE KEY Push and hold to enter user set mode e During user set mode push this key to select an item and change the value or condition using push CH Up CH Down Push and hold this key again to exit user set mode User set mode is also available via the Power ON function Refer to p 13 also OPT 1 2 3 KEYS Push to control the output signal level of the optional ports in the optional unit connector DIGITAL BUTTON KEY BIIS operation only Push to select the call ID list trans
6. If an incorrect connection is made after cutting the transceiver might be damaged NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury NEVER allow children to touch the transceiver NEVER expose the transceiver to rain snow or any liquids USE the specified microphone only Other microphones have different pin assignments and may damage the trans ceiver DO NOT use or place the transceiver in areas with tem peratures below 30 C or above 60 C or in areas subject to direct sunlight such as the dashboard AVOID operating the transceiver without running the vehi cle s engine The vehicle s battery will quickly run out if the transceiver transmits while the vehicle s engine OFF AVOID placing the transceiver in excessively dusty envi ronments AVOID placing the transceiver against walls This will obstruct heat dissipation AVOID the use of chemical agents such as benzine or alcohol when cleaning as they damage the transceiver sur faces BE CAREFUL The transceiver will become hot when operating continuously for long periods TABLE OF CONTENTS IMPORTANT ositit ete uatan atada ea de i EXPLICIT DEFINITIONS AAA i PRECAUTION fssciscescecteecrtectvecvescatssessoutesereinarescrtvcriessiustsssteisreieveicoee i TABLE OF CONTENTS 1 PANEL DESCRIPTION cscessssssessssesseesseeseesesseenessesseeseensaeee ME Front E EE 1 E Fun
7. OPC 617 as shown below Cut off the bushing as in the illustration when you install the optional OPC 617 OPTIONAL CABLE PIN ASSIGNMENT O00000 0000 Dimmer cont IN or Horn drive cont OUT IGSW cont IN AF GND AF OUT Det AF GND Det AF OUT Mod GND Mod IN PTT control IN or FTSW control IN E Antenna A key element in the performance of any communication sys tem is an antenna Contact your dealer about antennas and the best places to mount them E Fuse replacement A fuse is installed in the supplied DC power cable If a fuse blows or the transceiver stops functioning track down the source of the problem if possible and replace the damaged fuse with a new rated one OFuse rating 10 A USE the 10 A fuse only E Cleaning If the transceiver becomes dusty or dirty wipe it clean with a soft dry cloth AVOID the use of solvents such as benzene or Noh alcohol as they may damage the transceiver sur a faces CONNECTION AND MAINTENANCE 4 E Options e RMK 2 SEPARATION KIT OPC 609 SEPARATION CABLE Allows you to install the transceiver main unit separately from the front panel for operating convenience e SP 5 SP 22 EXTERNAL SPEAKER Input impedance 4Q Max input power 5 W SP 5 Large speaker for good audio quality SP 22 Compact and easy to install The same as supplied with the transceiver depending on version e HM 100TN HM 100N HM 148 HM 152 HM
8. Y error beep sounds and i is displayed when no YW answer back is received after the calls NY BIIS OPERATION 3 Push PTT to transmit release to receive Push P4 Moni Audi to send the Clear down signal For your information When the UpDate setting for the call code is enabled the set code is overwritten into the call code memory 3 BIIS OPERATION E Receiving a message Receiving a status message When a status message is received e Beeps sound e The calling station ID or text and the status message is dis played alternately when the indication mode is 1 line depending on the setting Y Push P4 Moni Audi to return to the standby condition Y NOTE Only the calling station ID or text is displayed no E message is displayed alternately when the scroll timer is g set to OFF In this case push Status Up Status Down Z to display the status message manually MN Receiving an SDM Short Data Message When an SDM is received e Beeps sound e The calling station ID or text and the SDM is displayed alter nately when the indication mode is 1 line depending on the set ting ev EI appears Appears Ki When the received SDM includes more than 12 charac ters the message scrolls automatically when the auto matic scroll function is activated e Push Status Up Status Down to scroll the message manually Y 4 Push
9. assigned as DIGITAL key when that key has been activated PANEL DESCRIPTION 1 E Programmable function keys The following functions can be assigned to DIAL UP DOWN PO P1 P2 P3 and P4 programmable func tion keys Consult your Icom dealer or system operator for details con cerning your transceivers programming If the programmable function names are bracketed in the fol lowing explanations the specific key is used to activate the function depends on the programming The functions you can assign to DIAL are limited Only functions marked with x can be assigned yx CH UP AND DOWN KEYS Push or Rotate to select an operating channel Push or Rotate to select a transmit code channel after pushing TX Code CH Select Push or Rotate to select a DTMF channel after pushing DTMF Autodial Push or Rotate to select a scan group after pushing and holding Scan A Start Stop Scan B Start Stop Push or Rotate to select a BIS code status number or SDM after pushing Digital Rotate when this function is assigned to DIAL ye ZONE UP AND DOWN KEY This function is for DIAL only Rotate to select the desired zone S 1 PANEL DESCRIPTION ZONE KEY Push this key then select the desired zone using CH Up CH Down What is zone The desired channels are assigned into a zone according to the intended use for grouping For example Staff A and Sta
10. level is pre programmed e Select memory channels tone channels and DTMF codes FUNCTION DISPLAY p 2 when in the DTMF code channel selection mode Displays a variety of information such as an operating Set TX codes and BIIS status number Input text message for SDM operation channel number name 5 tone code DTMF numbers and dee g poras audible condition etc t Start up with a password he BUSY INDICATOR Kiel Lights green while receiving a signal or when the squelch is open Rotate to select an operating channel etc e IC F1810 F2810 UP DOWN Keys Push to select an operating channel etc The desired function can be assigned by your dealer p 3 a 1 PANEL DESCRIPTION POWER SWITCH POWER Push to turn the power ON and OFF e The following functions are available at power ON as options Automatic scan start Password prompt Set mode TRANSMIT INDICATOR Lights red while transmitting DEALER PROGRAMMABLE KEYS Desired functions can be programmed independently by your dealer p 3 E In this instruction manual these keys are from the left J called POV P1 P2 P3 P4 MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro phone E NEVER connect non specified microphones The pin ZY assignments may be different and the transceiver may be damaged MICROPHONE The supplied microphone has a PTT switch and a hanger hook e The following functions are available whe
11. 152T HAND MICROPHONE HM 100TN HM 152T Hand microphone with a DTMF key pad e SM 25 DESKTOP MICROPHONE e UT 109 02 UT 110 02 SCRAMBLER UNITS Non rolling type UT 109 Rolling type UT 110 voice scrambler unit provides higher communication security e UT 111 LTR TRUNKING BOARD Provides trunking operation e OPC 617 Acc CABLE Allows you to connect to an external terminal DOC O ICOM We Icom Inc Japan 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive 1999 5 EC and that any applicable Essential Test Suite measurements have been performed Kind of equipment VHF TRANSCEIVER Type designation IC F1710 F1810 DECLARATION OF CONFORMITY C 01680 D sseldorf 15th Mar 2005 Place and date of issue Icom Europe GmbH Himmelgeister stra e 100 D 40225 D sseldorf 136 174 MHz 12 5 KHz 25 KHz 136 174 MHz 12 5 KHz 20 KHz Version where applicable This compliance is based on conformity with the following harmonised standards specifications or documents i EN 301 489 1 v1 2 1 2000 8 ii EN 301 489 5 v1 2 1 2000 8 iii EN 60950 2000 iv EN 300 086 2 v1 1 1 March 2001 v EN 300 219 March 2001 vi EN 300 113 2 v1 1 1 March 2001 Authorized representative name H Ikegami General Man
12. 60950 2000 iv EN 300 086 2 v1 1 1 March 2001 v EN 300 219 March 2001 Authorized representative name H Ikegami General Manager vi EN 300 113 2 v1 1 1 March 2001 Signature Icom Inc About e marking Detailed installation notes for Icom mobile transceivers to be fitted into vehicles are available Please contact your Icom dealer or distributor Count on us lt Intended Country of Use gt OGER FRA OESP OSWE UA ONED OPOR ODEN LIGBR OBEL OITA OFIN Um OLUX OGRE OSUI L NOR A 6407H 1EU Icom Inc Printed in Japan SR See d ck 4 2004 2005 Icom Inc 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan
13. Group call When a group call is received e Beeps sound e qn appears and the mute is released e The programmed text message e g and the calling sta tion ID or text is displayed when the indication mode is 2 lines eThe programmed text message e g 2LHii and the calling station ID or text is displayed alternately when the indication mode is 1 line depending on the setting e amp appears or blinks depending on the setting Appears Appears or blinks L Y dal amp Push and hold PTT then speak into the microphone at a normal voice level e TX indicator lights red 77 NOTE Only one station is permitted to speak Q Release PTT to return to receive e BUSY indicator lights green while receiving a signal To finish the conversation push MONITOR Moni Audi to send the Clear down signal e Eith i n can send a Clear down signal s displayed for 2 sec approx e qn disappears and the transceiver returns to the standby con dition BIIS OPERATION 3 Q Displaying the received call record Queue indication The transceiver memorizes the calling station ID in the mem ory Up to 3 calls can be memorized and the oldest call record is erased when a 4th call is received However once the transceiver is powered OFF the all records are cleared Push P1 Digital for 1 sec e Displays following indication When a record is available
14. O gt ICOM INSTRUCTION MANUAL VHF MOBILE TRANSCEIVER IC F1710 IC F1810 UHF MOBILE TRANSCEIVER IC F2710 IC F2810 Icom Inc O m BIIS 1200 Compatible AAAA RAD me es ca ies ic CP e 4 KH E Above photo shows the IC F1810 or IC F2810 IMPORTANT READ ALL INSTRUCTIONS carefully and com pletely before using the transceiver SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC F1710 IC F1810 IC F2710 and IC F2810 VHF UHF MOBILE TRANSCEIVERS EXPLICIT DEFINITIONS WORD DEFINITION AWARNING Personal injury fire hazard or electric shock may occur CAUTION Equipment damage may occur NOTE If disregarded inconvenience only No risk of personal injury fire or electric shock Icom Icom Inc and the COM logo are registered trademarks of Icom Incorporated Japan in the United states the United Kingdom Germany France Spain Russia and or other countries All other products or brands are registered trademarks or trademarks of their respective holders PRECAUTION Z WARNING NEVER connect the transceiver to an AC outlet This may pose a fire hazard or result in an electric shock NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery This connection will ruin the transceiver NEVER cut the DC power cable between the DC plug and fuse holder
15. P4 Moni Audi to return to the standby condition Received message selection The transceiver memorizes the received message in the memory Up to 6 messages for status and SDM or 95 char acter SDM s can be memorized The oldest message is erased when the 7th message is received However once the transceiver is powered OFF all messages are cleared Push P1 Digital for 1 sec e Displays queue memory Push P1 Digital momentarily e Displays message memory When a message is available When no message is available Y Push Up or Down or rotate DIAL to select the desired message eWhen selecting the SDM that includes more than 12 characters the message scrolls automatically when the automatic scroll function is activated e Push Status Up Status Down to scroll the message manually BIIS OPERATION 3 Push P1 Digital for 1 sec again to return to the standby condition eWhen no operation is performed for 30 sec the transceiver returns to the standby condition automatically 3 BIIS OPERATION E Transmitting a status General The status message can be selected with the programmed text and the message text is also displayed on the function display of the called station Up to 24 status types 1 to 24 are available and the status messages 22 and 24 have designated meanings Status 22 Emergency Status 24 GPS request The status 22 can also be used as a normal
16. ager Signature Icom Inc CE Versions of the IC F1710 F1810 F2710 F2810 which display the CE symbol on the serial number seal comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999 5 EC This warning symbol indicates that this equipment operates in non harmonised frequency bands and or may be subject to licensing conditions in the country of use Be sure to check that you have the correct version of this radio or the correct pro gramming of this radio to comply with national licensing requirement O ICOM We Icom Inc Japan 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive 1999 5 EC and that any applicable Essential Test Suite measurements have been performed Kind of equipment UHF TRANSCEIVER Type designation IC F271 O F281 O DECLARATION OF CONFORMITY C 0168 Diisseldorf 25th Feb 2005 Place and date of issue Icom Europe GmbH Himmelgeister stra e 100 D 40225 Diisseldorf 400 470 MHz 12 5 KHz 25 KHz 400 470 MHz 12 5 KHz 20 KHz Version where applicable This compliance is based on conformity with the following harmonised standards specifications or documents i EN 301 489 1 v1 2 1 2000 8 ii EN 301 489 5 v1 2 1 2000 8 iii EN
17. ct the desired record OG Push PO Call or PTT to call PTT call can be made only when PTT call capability is permitted ZY NOTE When no answer back is received the trans ceiver repeats the call 3 times default automatically and is displayed during each call However an error beep sounds and is displayed when no CG answer back is received after the calls Push PTT to transmit release to receive Push P4 Moni Audi to send the Clear down signal WA Q Direct code entry While in the standby condition push P3 TX Code Enter to enter the TX code edit mode e Code digit for editing blinks Push P3 TX Code Enter to select the desired digit to be edited e Digit for editing differs according to the setting Set the desired digit using CH Up CH Down DIAL or 10 keypad IC F1810 or IC F2810 only Push P3 TX Code Enter to set the digit then the digit to the right will blink automatically e When the 10 keypad is used for setting the digit to the right will blink automatically without pushing P3 TX Code Enter Repeat 3 and to input all allowable digits Push PO Call or PTT to call PTT call can be made only when PTT call capability is permitted Y NOTE When no answer back is received the trans Y ceiver repeats the call 3 times default automatically g MO and 3 i is displayed during each call However an
18. ction display E Programmable function keys 2 BASIC OPERATION ccccessseesessessesseseeessesseesnesseseeeseeneneees 8 13 E Turning power ON Ho E Channel selection oo eee cesecssseeseeseseeeeseseeeeeseaeeaeseeeeaeeeneatens E Call procedure oe cece eee eeeeeeeeeceeeseseeseeeseseeeseseeeeaeees E Receiving and transmitting Pe S Transmitting Ne TX code channel selection s nssnesnsssnssnsennernernnrrnernnrnnnnnne 10 TX code number edit S DTMF transmissions e a G a E Scrambler function sssesseseseeieeeerereineierrersrrsinirernrrernererrernreerneen E User set mode Se 3 BIS OPERATION cccececsseseeessessesssessessessesseeseesseseneseenenes 14 24 E Default setting 0 eee ceceeeseeseeeeeeseeseeeaeseeeeaecseeeaessnseaeeeneeeeaes E Receiving a call d Olndividual Calll sde K l RUE Displaying the received call record Queue indication E Transmitting a TR OUSiNg Call MEMO geed Geer Edge dek Calling back from the queue channel O Direct COMO MWY EE E Receiving A MESSAGE cscs cece ceeeseeeseseeesseenseenseeeseansneneaees 18 Receiving a status message ee cece tenet 18 Receiving an SDM Short Data Message eee 18 Received message selection E Transmitting a status KA TEE Transmitting a status 2 E Transmitting an SDM Short Data Message 21 SE EE CT EE Transmitting an SDM Si Q Programming an SDM Memory cece eee ee ete
19. dit mode directly for both 5 tone and BIIS Push this key after the communica tion to send a Clear down signal during BIIS channel operation P2 Null No function is assigned Up Down DIAL CH Up Down While in the standby condition selects the operating channel After pushing Digital or TX Code CH Select selects call list or TX code channel respectively P3 TX Code Enter P4 Moni Audi E Receiving a call Individual call When an individual call is received e Beeps sound e 411 appears and the mute is released e The programmed text message e g and the calling station ID or text is displayed when the indication mode is 2 lines es The programmed text message e g and the calling station ID or text is displayed alternately when the indication mode is 1 line depending on the setting e A appears or blinks depending on the setting Appears Appears or blinks Y 4 a Push and hold PTT then speak into the microphone at a normal voice level es TS indicator lights red Release PTT to return to receive e BUSY indicator lights green while receiving a signal To finish the conversation push P4 Moni Audi to send the Clear down signal e Either station can send a Clear down signal P is displayed for 2 sec approx e qn disappears and the transceiver returns to the standby con dition
20. ed Push PO Call or PTT to transmit the SDM to the selected station group PTT call can be made only when PTT call capability is permitted e2 beeps will sound and the transceiver returns to the standby condition automatically when the transmission is successful 22 3 BIIS OPERATION Programming an SDM memory IC F1810 or IC F2810 only During standby condition push P1 Digital twice then push Up or Down to select the desired SDM to be edit ed Push or to enter the message editing condition The first character blinks when is pushed the last character blinks when is pushed e amp blinks Blinks Blinks a When is pushed Q Push the appropriate digit key 0 to 9 to enter the desired character See the table at right for the available characters Pushing UP also enters space pushing DOWN deletes the selected character Push to move the cursor to the right push to move the cursor to the left Repeat steps 3 and to set the desired text message Push P1 Digital for 1 sec to overwrite the set content into the memory e Push P1 Digital momentarily to cancel the editing and return to the original message indication e Available characters Key Characters SSISRESRZS NOTE A decimal point can only be written with the CS F70 F1700 CLONING SOFTWARE Pre programmed charac ters can be rewritten with
21. eeeeeeeee 22 E Position data transmission eee eee eeeeeeeeeeeeteaee 23 E Printer connection A E Digital EE E Auto emergency transmission s nssssssesnsisernerrerrerrnsrnsennsenne 23 E Stun function y E BIS indication ege cecesnvssevcensceoccesrestecdansteccinssivvensceeseestesees 24 E Priority A channel selection ss sssnssnssnsssnsrerinerrerrerrnnrnnernsnnne 24 E Horn output 4 CONNECTION AND MAINTENANCE 0 ceecessstsseeeeseeeeeeee 25 29 E Rear panel connection ou cece e cece eee e see eeeeeseeseeetae E Supplied Accessories E Mounting the transceiver o oo eee ce eee eee eseeeeeeeseaeeeeatae E Optional UT 111 installation 2 cece eee eeeeeeeeeeeeees E Optional UT 109 or UT 110 installation 5 E Optional OPC 617 installation eee eee eeeeeeeeeeeeeees W ISSEN ESA E Fuse replacement Fa E Cleaning Asea a a Raa aa ae eE AEAEE Bellen EE CA DLO oe EAE E PANEL DESCRIPTION 1 E Front panel AR Ee SE 3 gt 1 lg 7 Sei eo KC w GE C E IC F1710 SC S Ge g V Su 6mo ero O gt EEE SSS SE e Ce 8w ES IC F1810 i F2810 m DODOGE ies O AF VOLUME CONTROL KNOB 10 KEYPAD IC F1810 or IC F2810 only Rotate the knob to adjust the audio output level The keypad allows you to enter digits to e Minimum audio
22. ff B are assigned into a Business zone and John and Cindy are assigned into a Private zone MMA SCAN A START STOP KEY This key s operation depends on the Power ON Scan setting When the power ON scan function is turned OFF Push to start and cancel scanning operation In case of transmission during scan cancels scanning When the power ON scan function is turned ON Push to pause scanning Scanning resumes after a speci fied time period has passed In case of transmission during scan pauses scanning Scanning resumes after a specified time period has passed after the transmission is finished Push and hold this key for 1 sec to indicate the scan group then select the desired group using CH Up CH Down SCAN B START STOP KEY Push to start and cancel scanning operation In case of transmission during scan pauses scanning Scanning resumes after a specified time period has passed after the transmission is finished Push and hold this key for 1 sec to indicate the scan group then select the desired group using CH Up CH Down SCAN ADD DEL TAG KEY Push to add or delete the selected channel to from the scan group PRIO A B KEYS Push to select Priority A or Priority B channel Push and hold Prio A Rewrite to rewrite the Prio A chan nel MR CH 1 2 3 4 KEYS Push to select an operating channel directly MONI AUDI KEY Activates one of or two of the following
23. functions on each channel independently e Push and hold to un mute the channel audio is emitted Audible condition e Push to mute the channel sets to Inaudible only e Push to un mute the channel sets to Audible only e Push after the communication is finished to send a reset code G NOTE The un mute condition Audible condition may E automatically return to the mute condition Inaudible con Z dition after a specified period depending on programming SS PUBLIC ADDRESS KEY While in the hailer mode push this key for the audio output via the hailer amplifier Ask your dealer for details While in the normal mode the audio output via the cable can be controlled from the transceiver separately from VOL con trol knob when an optional OPC 617 acc caBLe is installed es This audio output can be used as a public address function when an external audio amplifier and speaker are connected additionally Push this key then speak into the microphone while pushing the PTT switch e CH Up CH Down allow you to set the audio output level from min imum to maximum RX SPEAKER KEY While in the hailer mode the external speaker drive function is also available simultaneously when the external connec tions are made for the public address function The received audio can be heard via the external speaker when this key is pushed e This function is useful when you are out of t
24. g can be recorded when using a PC dispatch application In addition when using the ANI with log in the PTT side tone function can be used to inform you that the ID is sent and voice communication can be performed E Auto emergency transmission When Emergency Single Silent or Emergency Repeat Silent is pushed an emergency signal is automatically transmitted for the specified time period The status 22 Emergency is sent to the selected ID station and the position data is transmitted after the emergency sig nal when a GPS receiver is connected to the transceiver The emergency transmission is performed on the emergency channel however when no emergency channel is specified the signal is transmitted on the previously selected channel There is no change in the function display or beep emission during automatic emergency transmission 24 3 BIIS OPERATION E Stun function When the specified ID set as a killer ID is received the stun function is activated When the killer ID is received the transceiver switches to the password required condition Entering of the password via the keypad is necessary to operate the transceiver again in this case E BIIS indication The following indications are available for the BIIS operation on a BIIS channel L Individual group call is successful Message status or SDM transmission is suc cessful No answer back is received Appears during retry of t
25. he call 2nd call End the communication Operating channel is in the busy condition E Priority A channel selection When one of the following operations is performed the trans ceiver selects the Priority A channel automatically Priority A is selected when Clear down signal is received transmitted Set the Move to PrioA CH item as Clear down Turning the power ON The Priority A channel is selected each time the transceiv er power is turned ON e Status call The Priority A channel is selected when transmitting a sta tus call Enable the Send Status on PrioA CH item in the BIS configuration E Horn output Automatic honking function is available when the optional OPC 617 Acc CABLE is connected When a status message is received the transceiver controls the vehicles horn for the specified time period to inform a status message is received This function is convenient when the operator away from the transceiver Ask your dealer or system operator or refer to the service manual for connection and setting details CONNECTION AND MAINTENANCE 4 E Rear panel connection Antenna ANTENNA CONNECTOR Reserved fora Connects to an antenna future function Contact your dealer about EXTERNAL antenna selection and SPEAKER JACK N placement Connect a 4 8 o external speaker UU 0 W oO EOE DC POWER RECEPTACLE Connects to a 12 V DC battery Pay atten WDD
26. he vehicle e The audio output level is linked to the transceiver s volume control LIGHT KEY Push to turn the transceiver s backlight ON for about 5 sec when the backlight function is turned OFF in user set mode LOCK KEY Push and hold to electronically lock all programmable keys except the following Call incl Call A and Call B Moni Audi and Emergency PANEL DESCRIPTION 1 HIGH LOW KEY Push to select the transmit output power temporarily or per manently depending on the pre setting e Ask your dealer for the output power level for each selection C TONE CH ENT KEY Push to select the continuous tone channel using CH Up CH Down to change the tone frequency code setting after pushing this key The selected channel remains set as the continuous tone channel until another channel is designated as such TALK AROUND KEY Turn the talk around function ON and OFF The talk around function equalizes the transmit frequency to the receive frequency for transceiver to transceiver communication WIDE NARROW KEY Push to toggle the IF bandwidth between wide and narrow e The wide passband width can be selected from 25 0 or 20 0 kHz using the CS F70 F1700 CLONING sorTware Ask your Dealer for details DTMF AUTODIAL KEY Push to enter the DTMF channel selection mode Then select the desired DTMF channel using CH Up CH Down After selecting the desired DTMF channel push this key to transmit the DTMF code
27. ks Push CH Up CH Down or 10 keypad or rotate CH Up Down to set the desired digit Push TX Code Enter to set the digit The digit to the right will blink automatically e When the 10 keypad is used for setting the digit to the right will blink automatically without pushing TX Code CH Select Repeat and to input all allowable digits Push Call or PTT to transmit the edited TX code IC F1810 or IC F2810 only 12 2 BASIC OPERATION DTMF transmission If the transceiver has DTMF Autodial assigned to it the auto matic DTMF transmission function is available Up to 8 DTMF channels are available TO SELECT A TX CODE Push DTMF Autodial a DTMF channel appears Push CH Up or CH Down or rotate CH Up Down to select the desired DTMF channel Push DTMF Autodial to transmit the DTMF code in the selected DTMF channel E Scrambler function The voice scrambler function provides private communication between stations The frequency inversion type is equipped to all versions moreover the optional Rolling or Non rolling type can be available Push Scrambler to turn the scrambler function ON appears Push Scrambler again to turn the scrambler function OFF e 0 disappears E User set mode User set mode is accessed with User Set Mode and allows you to set seldom changed settings In this case you can customize the transceiver operati
28. l is in mute condition Inaudible condition 4n does not appear The channel is busy Un matched or matched CTCSS is received Depending on the pre setting The selected channel is a receive only channel e Time out timer After continuous transmission for the pre programmed time period the time out timer is activated causing the transceiv er to stop transmitting e Penalty timer Once the time out timer is activated transmission is further inhibited for a period determined by the penalty timer TX code channel selection If the transceiver has TX Code CH Select assigned to it the indication can be toggled between the operating channel number or name and TX code channel number or name When the TX code channel number or name is displayed CH Up CH Down selects the TX code channel USING TX CODE CH SELECT KEY Push TX Code CH Select a TX code channel number or name appears Push CH Up or CH Down or rotate CH Up Down to select the desired TX code channel Push Call or PTT during BIIS operation to transmit the selected TX code USING TX CODE CH UP TX CODE CH DOWN KEY If the transceiver has a TX Code CH Up TX Code CH Down or TX Code CH Up Down key assignment the pro grammed TX code channel can be selected directly when pushed or rotated ZY NOTE for PMR or BIS PMR operation e The LCD indication does not change when the operating channel number o
29. mit message and stand by condition Toggles between queue channel and received message record indication after queue channel is selected Push and hold to select queue channel indication PANEL DESCRIPTION 1 x STATUS UP DOWN KEYS BIIS operation only While in the standby condition push or rotate to display the transmit status indication and select a status number When a received SDM is displayed push or rotate to cancel the automatic scroll and scroll the message manu ally When an SDM that contains more than 12 characters is displayed push or rotate to scroll the message manually Rotate when this function is assigned to DIAL ml BASIC OPERATION E Turning power ON Push O to turn the power ON If the transceiver is programmed for a start up password input the digit codes as directed by your dealer e 10 keypad can be used for password input IC F1810 or IC F2810 only e The keys as below can be used for password input The transceiver detects numbers in the same block as identical Therefore 01234 and 56789 are the same Cr gt CC fc lie Wes Paes P3 Me P4 CH HHC In this instruction manual these keys are from the left called PO P1 P2 P3 P4 ve 0 5 0 1 2 3 4 5 6 7 8 9 NUMBER When the PASSWORD indication does not clear after inputting 6 digits the input code n
30. n the microphone is on or off hook Automatic scan start when on hook Automatic priority channel selection when off hook Sets to Inaudible condition mute condition when on hook Sets to Audible condition unmute condition when off hook E Function display o 8 o Lk Yul LOW qn D i SIGNAL STRENGTH INDICATOR Indicates relative signal strength level LOW POWER INDICATOR Appears when low output power is selected AUDIBLE INDICATOR Appears when the channel is in the audible unmute condition Appears when the specified 5 tone BIIS code is received COMPANDER INDICATOR Appears when the compander function is activated SCRAMBLER INDICATOR Appears when the voice scrambler function is activated BELL INDICATOR Appears blinks when the specific 5 tone BIIS code is received according to the pre programming CALL CODE MEMORY INDICATOR Appears when the call code memory is selected SDM MEMORY INDICATOR Appears when the SDM memory is displayed SDM INDICATOR Appears when an SDM is received or a transmit SDM is selected ALPHANUMERIC DISPLAY Displays an operating channel number channel name Set mode contents DTMF code etc The indication mode can be selected from 1 line or 2 lines Ask your dealer for details In this instruction manual the LCD illustration is described using the 2 lines indication mode ACTIVATED KEY INDICATOR Appears above the key
31. on to suit your preferences and operating style Entering the user set mode While pushing and holding P1 and P2 push to turn the power ON Then push and hold PO to enter user set mode PO P1 P2 0 Push PO several times to select the appropriate item Then push Up or Down or rotate DIAL to set the desired level condition e Available set mode functions are Backlight LCD Contrast Beep Beep Level SQL Level AF Min Level Mic Gain Horn P0 Up Down or DIAL BASIC OPERATION 2 Push again to exit set mode User set mode is also available via a programmable key Please refer to p 7 User Set Mode section 14 BIIS OPERATION 3 E Default setting The following functions are assigned to each programmable key as the default However the assigned function can be changed by your dealer Ask your dealer for details 7 NOTE TX Code Enter must be assigned to a key In this instruction manual these keys Le are from the left called PO P1 P2 P3 P4 PO Call Push to transmit a 5 tone BIIS call when the selected channel is a 5 tone or BIIS channel P1 Digital Push to select the call list ID transmit message or to display the receive message record for selection Push to enter the ID code e
32. r name is displayed Depending on the pre setting e To check the selected TX code push TX Code CH Select WMWQA AN TX code number edit If the transceiver has TX Code CH Select or TX Code Enter assigned to it TX code contents can be edited within the allowable digits USING TX CODE CH SELECT KEY Push TX Code CH Select to enter the TX code channel selection mode e Select the desired channel before entering the TX code channel selection mode if necessary Push TX Code CH Select for 1 sec to enter the TX code edit mode 3 Push TX Code CH Select to select the desired digit to be edited e The digit to be edited blinks Push CH Up CH Down or 10 keypad or rotate CH Up Down to set the desired digit Push TX Code CH Select to set the digit The digit to the right will blink automatically e When the 10 keypad is used for setting the digit to the right will blink automatically without pushing TX Code CH Select Repeat and to input all allowable digits Push Call or PTT to transmit the edited TX code IC F1810 or IC F2810 only BASIC OPERATION 2 USING TX CODE ENTER KEY Select the desired TX code channel via TX Code CH Select CH Up or CH Down TX Code CH Up TX Code CH Down or TX Code CH Up Down Push TX Code Enter to enter the TX code edit mode Push TX Code Enter to select the desired digit to be edit ed e The digit to be edited blin
33. securely with the 4 supplied screws to a thick surface which can support more than 1 5 kg E Fitwasher D Ss amp I A When using self tapping screws CONNECTION AND MAINTENANCE 4 E Optional UT 111 installation Install the optional UT 111 unit as follows Turn the power OFF then disconnect the DC power cable Unscrew the 4 cover screws then remove the bottom cover Cut the pattern on the PCB at the CP57 then solder CP58 as shown below Install the unit as shown in the diagram below Replace the bottom cover and screws then re connect the DC power cable GY See p 28 when unin Z stalling the unit 4 CONNECTION AND MAINTENANCE E Optional UT 109 or UT 110 installation Turn the power OFF then disconnect the DC power cable Unscrew the 4 cover screws then remove the bottom cover 3 Cut the pattern on the PCB at the TX mic circuit MIC and RX AF circuit AF OUT then solder CP37 as shown below Install the scrambler unit as described in the installation of optional UT 111 installation on p 27 Replace the bottom cover and screws Y NOTE When uninstalling the unit Ge sure to re solder the disconnected points and un solder the connected G points as above when you Y remove the unit Otherwise Gro TX modulation or AF f output is available Re solder LU A gt R Un solder e 2 SE r x E Optional OPC 617 installation Install the
34. status message by disabling the designated meaning However the status 24 is fixed The status call can be sent with both individual and group calls Q Transmitting a status While in the standby condition push P1 Digital then push Up or Down or rotate DIAL to select the desired station group code Push P1 Digital again then push UP or DOWN to select the desired status message Or you can select the desired status message using Status Up Status Down key directly Y Status message is displayed Push PO Call or PTT to transmit the status message to the selected station group PITT call can be made only when PTT call capability is permitted e2 beeps will sound and the transceiver returns to the standby condition automatically when the transmission is successful BIIS OPERATION 3 E Transmitting an SDM Short Data Message Q General The short data message SDM can be sent to an individual station or group stations Also 8 SDM memory channels are available and the messages can be edited via PC program ming Q Transmitting an SDM While in the standby condition push P1 Digital then ER push Up or Down or rotate DIAL to select the desired station group code Push P1 Digital again then push Up or Down or rotate DIAL to select the desired SDM Or you can select the desired SDM using Status Up Status Down key directly Appears SDM is display
35. the 10 keypad except for the decimal point as it is not included in the transceiver char acter list and cannot be displayed again WA QQ E Position data transmission When the optional cable and a GPS receiver is connected to the transceiver the position longitude and latitude data can be transmitted automatically Ask your dealer or system operator for connection details The position data is transmitted when e Status 24 message is received When the status 24 message GPS request is received e Fully automatic When automatic position transmission is enabled send the position data according to Time Marker and Interval Timer settings PTT is released When Send with Logoff is enabled Set the Log In Off item as L OFF e After sending a status message When Send with Status is enabled e After sending an SDM When Send with SDM is enabled e After sending status 22 Emergency When Send with Emergency is enabled E Printer connection When the optional cable is connected to the transceiver a printer can be connected to print out the received SDM con tent and the ID of the station who sent the message Ask your dealer or system operator for connection details BIIS OPERATION 3 E Digital ANI The own ID can be transmitted each time the PTT is pushed log in or released log off during individual or group call communications By receiving the ANI the communication lo
36. umber may be incorrect Turn the power off and start over in this case E Channel selection Several types of channel selections are available Methods may differ according to your system set up NON ZONE TYPE Push CH Up or CH Down or rotate CH Up Down to select the desired operating channel in sequence or push one of MR CH 1 to MR CH 4 keys to select a channel directly ZONE TYPE Push Zone then push CH Up or CH Down or rotate Zone Up Down to select the desired zone AUTOMATIC SCAN TYPE Channel setting is not necessary for this type When turning power ON the transceiver automatically starts scanning Scanning stops when receiving a call E Call procedure When your system employs tone signaling excluding CTCSS and DTCS the call procedure may be necessary prior to voice transmission The tone signalling employed may be a selec tive calling system which allows you to call specific station s only and prevent unwanted stations from contacting you Select the desired TX code channel or 5 tone code according to your System Operator s instructions e This may not be necessary depending on programming e Refer to pgs 10 11 for selection Push the call key assigned to one of the dealer program mable keys or PTT After transmitting the remainder of your communication can be carried out in the normal fashion Non selective calling Selective calling
Download Pdf Manuals
Related Search