Instructions - Audio General Inc.
Contents
1. Suspend screens from holes in endcaps as shown S hooks chains or cable and turnbuckles should be provided by installer S hooks should go through the front holes on the endcaps see drawing on page 2 and both ends of the S hooks should be crimped for additional safety Chains should be attached to beams or other structural members Turnbuckles should be adjusted so screen hangs level Wall Installation Mount screen through holes in back of endcaps as shown Installer should furnish screws toggle bolts molly bolts nylon or lead anchors as required Wall Installation with 6 Extension Brackets Mount the brackets not included with screen see diagram below right using hardware recommended for Wall Installation above Then suspend the screen from the front holes with S hooks as in Suspended For added safety crimp both ends of the S hooks so the screen cannot come off For a more rigid installation mount the screen from the back holes to the front of the bracket by using the screws and nuts provided with the brackets Recessed Installation Recess should permit access for removal of screen if necessary Screen may be mounted as in suspended or wall installation Optional Ceiling Opening Trim Kit available see diagrams below and on page 2 and separate instruction sheet included with Ceiling Opening Trim Kit Electrical Connections Screen operates on 110 120V 60 hz 1 1 amp current draw2. hardware provided by installer Suspended gt Methods of Installation Fasteners for wall mounting by others 3 S Hooks for S w 4 suspended eee installation o O i by others I 7 8 hole for electrical connection Dims Side View aie a 4 o He L277 A e x 0 lo a fe o O O Mao Z 4 T 21 46 Y 1 melh rhe lt lt 4 gt a 63 4 gt 5 6 Extension 2 16 a Bracket a Le Appropriate hardware SS provided by installer ILT Limit Adjustment Continued from Page 1 To set the viewing surface to an alternate format O position move the viewing surface to the desired pg ays position and press the STOP button Press and UD TA hold STOP for at least three seconds to record Pw m Bt the position POSITION FUNCTION f Please Note Pressing and DOWN Set LOWER limit releasing the UP button on the switch will move the screen to its upper limit Pressing and releas UP Set UPPER limit CENTER Normal Operation ing the DOWN button will move the screen to its lower limit Switch Sid O While the motor is in motion pressing STOP for Back View less than two seconds will stop the viewing surface at its present position Once the motor is stopped pressing the STOP button will move the vie
3. over the roller When run to the down limit a minimum of 114 wraps of fabric must remain on the roller The motor limit screws are normally located on the audience left of screen roller DOWN LIMIT ADJUSTMENT To Reduce Screen Drop Raise screen surface about 1 above desired setting and turn off Turn the WHITE DOWN limit screw clockwise three screw turns roller revolution Test by running screen down and repeat steps 1 and 2 until desired position is reached To Increase Screen Drop Run screen to the down limit With the down switch on turn the WHITE DOWN limit screw counterclockwise three turns of screw equals roller revolution to increase drop Test by running screen up about 1 and back down to new down limit Repeat steps 2 and 3 until desired position is reached CAUTION At least 1 wraps of fabric must remain on the roller when screen is at the down limit UP LIMIT ADJUSTMENT Screen is Running Too Far Up Lower screen surface about 1 below desired setting and turn off Turn the YELLOW UP limit screw clockwise three screw turns roller revolution Test by running screen up Repeat steps 1 through 3 until desired position is reached Screen Needs to Run Up More Run screen down about 1 and turn off With the up switch on turn the YELLOW UP limit screw counterclockwise three turns of screw equals roller revolution Repeat steps 1 and 2 until desired position is reached CAU
4. Installation Operating Instructions Targa Electric Projection Screen by Draper Caution Read instructions through completely before proceeding Follow instructions carefully Installation contrary to instructions invalidates warranty Screen should be accessible for complete removal should fabric become damaged or should other service be required Screen should be installed level using a carpenter s level Nothing should be fastened to screen dowel or viewing surface Operating switch es packed separately in screen carton Do not discard with pack ing material Screen operates on 110 120V 60 hz 1 1 amp current draw NOTE Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment These instructions are meant as a guide only They do not imply any responsibility on the part of Draper Inc for improper installation or faulty workmanship at the jobsite Hanging Screen General When locating viewing surface and checking clearance for screen s operation remember surface is centered in case Handle case carefully to protect its finish Regardless of mounting method screen should be positively and securely supported so that vibration or even abusive pulling on the viewing surface will not cause case to work loose or fall Installer must insure that fasteners used are of adequate strength and suit able for the mounting surface chosen Suspended Installation
5. Junction box is located inside left endcap and cover plate is secured to endcap with two screws Junction box contains red black and white pigtail leads and green internal ground wire per wiring diagram on reverse Screen is shipped with internal wiring complete and control switch es fully boxed Wire connecting screen to switch es and switch es to power supply should be furnished by installer Connections should be made in accordance with attached wiring diagram and wiring should comply with National and local electrical codes All operating switches should be off before power is connected Ceiling Tile _ By others F 411 S Pearl St Spiceland IN 47385 USA I 765 987 7999 www draperinc com I fax 765 987 7142 Copyright 2007 Draper Inc Form Targa_Inst07 R4 Printed in U S A Operation Before operating screen remove tape securing fabric and dowel to roller If viewing surface hangs out of case 8 9 tape has probably been broken by rough handling in shipment allowing surface to unwrap one turn about the roller Manually wrap fabric back around the roller without turning the roller itself 110 120V Single Station Control 3 position up off down switch permits operation to be stopped at any point Factory adjusted limit switches automatically stop screen when fully down or fully up 110 120V Multiple Station Control Switches are similar in appearance to 110 120V Single Station Control Screen stops when switc
6. Low Voltage Controls Internal Screen Wiring o White Neutral r o Black r 7 Green Ground L_ I I I Dashed wiring by electrician I 1 l l l l l l Data Cable To Motor with Built In Low Voltage Wall Switch RF or IR Receiver or integrated control system l To 110 120V Line To Motor with Built In Low Voltage Pressing and holding the STOP button when the motor is at rest or in motion www draperinc com DRAPER 765 987 7999 for at least three seconds will record a new alternate format position Internal Screen Wiring Dashed wiring by electrician Data Cables Wall Switches i RF or IR Receivers i or integrated control systems To 110 120V Line
7. TION Do NOT allow the dowel to wrap up over the roller when the screen is running up This could damage the screen Caution Do not remove the roller assembly from the case unless necessary for repairs If the roller assembly is removed be sure motor is fully re seated in the bracket and re secure it carefully with the motor retaining spring see diagram at right Limit Adjustments Built in Low Voltage Motors Connect the ILT switch to the motor via the terminal blocks or via the modular port using four conductor modular cable When using modular cable the cable connectors MUST NOT be crimped in reverse as with standard telephone cable Set the slide switch to the lower position Press and hold the DOWN button on the switch to move the viewing surface to the desired lower limit If the screen moves in the opposite direction release the DOWN button and depress the STOP button This will reverse the operation of the UP and DOWN switches Set the slide switch to the higher position Move the viewing surface to the desired upper limit by pressing and holding the UP button on the wall switch Return the slide switch to the center position to return to normal operation Continued on Page 2 If you encounter any difficulties installing or servicing your Targa screen call your dealer or Draper Inc Spiceland Indiana 765 987 7999 or fax 765 987 7142 Targa by Draper Types of Installation Wall Mounted Appropriate
8. h is released and may be restarted in either direction Factory adjusted limit switches stop screen automatically when fully up or fully down 24V Control Three button up stop down switches stop at any point desired operate in any sequence Factory adjusted limit switches automatically stop screen when fully up or fully down Key Operated Switching Two kinds of key operated switches are optionally available with this unit The key operated power supply switch controls power to the screen and switches When it is off the switches will not operate screen Key may be removed from the switch in either on or off position A three position key switch permits the screen to be operated directly by key In this case the screen s operator must always have a key RS232 Ethernet Serial communication and network communication optionally available with wall switches RF or IR remote Limit Adjustments Standard Quiet Motors Tools needed Flashlight small flathead screwdriver Allen wrench 4mm or 5 2 Screen settings have been factory set as ordered and should not normally require further adjustment However if you find it necessary to adjust for more or less viewing area proceed as follows CAUTION Always be prepared to shut screen off manually when new adjustment is being tested Screen may be severely damaged if viewing surface is allowed to run too far up or too far down When running up the dowel should never wrap
9. wing surface to its alternate format position Page 2 of 2 Case Dimensions T 1 4 oes m E mw Fabric width 7 el 5 7 8 Q a is 7 8 dia a i Viewing electrical ijai SS connection 31 2 surface hole Wiring Diagrams 110 120V Motor and Quiet Motor Single Station Control Internal Screen Wiring o White Common r o Black Down gt Red Up gt Green Ground L I I f Dashed wiring by electrician I I I Control switch Blue o Rea l gt Black Single gang box by others Min 4 x 21 8 x 17 8 deep r L4 Location of key Operated on off L switch if furnished To 110 120V Line Multiple Station Control Internal Screen Wirin A g 4 o White Common 7 l ras oo Black Down o Red Up L Red Blue Single gang box by others i Min 4 x 21 8 x 17 8 deep l 3 shown More or less equally I feasible 7 Location of key 1 operated on off uf switch if furnished I it oe r gt 2 Green Ground E oie po Cap off with wire l E nut and tape i SRS ele I I Red Blue I l I Black i Dashed wiring l i by electrician l Red Blue i l I I ml l Black l l I I I J To 110 120V Line Wiring Diagrams 110 120V Motor and Quiet Motor with Built in Low Voltage Controller Single Low Voltage Control Multiple
Download Pdf Manuals
Related Search