SDS2000 Quick Start Manual
Contents
1. SDS2000 Quick Start I SIGLENT II Safety Terms and Symbols Terms on the product These terms may appear on the product DANGER Indicates direct injuries or hazards that may happen WARNING Indicates potential injuries or hazards that may happen CAUTION Indicates potential damages to the instrument or other property that may happen Symbols on the product These symbols may appear on the product AAO Warning Hazardous Protective Earth Voltage SDS2000 Quick Start Earth Ground Ground Chassis Ground General Care and Cleaning Care Do not store or leave the instrument in direct sunshine for long periods of time Notice e To avoid damages to the instrument or probe please do not leave them in fog liquid or solvent Cleaning Please perform the following steps to clean the instrument and probe regularly according to its operating conditions 1 Disconnect the instrument from all power sources and then clean it with a soft wet cloth 2 Clean the loose dust on the outside of the instrument and probe with a soft cloth When cleaning the LCD take care to avoid scarifying it Notice To avoid damages to the surface of the instrument and probe please do not use any corrosive liquid or chemical cleanser e Make sure that the instrument is completely dry before restarting it to avoid short circuits or personal injuries SIGLENT Contents STS ASS Ale ty GUMMA Aen e2. lt gt gt lt selected In the figure below the time interval between two continuous rising edge and the currently set time satisfy the limit range lt gt M 100 us Delay0 00 ps Sa 2 000Gsa Curr 2 8Mpts 1X IMQ AC 500 midi Limit Range lt gt E s A MM any 8 SDS2000 Quick Start Runt Trigger Runt trigger includes positive runt trigger and negative runt trigger This trigger mode is used to trigger pulses that pass through one trigger level but fails to pass through the other trigger level as shown in the figure below Positive runt pulse High LeveL__ L_ _f_ J J J _ _ L L eer Low Level F h t b F 4 t Negative runt pulse In the figure below the trigger signal are positive runt pulse M50 0us Delay 100s Sa 2 000Gsa Curr 14Mpts a MQ DC 1 00 Vidiv Coupling DC Pattern Trigger Identify a trigger condition by looking for a specified pattern This pattern is a logical combination AND OR NAND NOR of the two channels Each channel can be set a value among High Low or Invalid In the figure below the selected logic is AND both channel 1 and 2 are set High SIGLENT M100us Delay 0 00ps v Sa 1 0053sa s Curr 14Mpts IMO AC 100 v d 1X IMO AC 100 Vidiv Typ ype CHI High CH2 High CH3 Invalid CH4 Invalid Next Page Pattern 9 A 5 2 amv aw SEE I2C Trigger After
3. Output Terminal on the front panel 4 Press 5 Observe the waveform on the screen In normal condition the display should be a square waveform as shown in the below SDS2000 Quick Start 3 SIGLENT SIGLENT 6 Test the other channels in the same method If the Probe Compensation The Front Panel actual square waveforms does not match that in the figure above please perform Probe Compensation You should properly compensate the probe at first use of it Non compensated or inadequate compensated probe Note To avoid electric shock when using the probe may cause inaccurate measurement The following steps please firstly make sure that the insulated wire are about probe compensation of the probe is in good condition and do not touch the metallic part of the probe when it is connected 1 Perform step 1 2 3 and 4 of Function Inspection to a high voltage 2 Check the displayed waveforms and compare them with the following figure YIU TW Under Compensated Over Compensated Correctly Compensated 3 Use a nonmetallic driver to adjust the low frequency compensation adjustment hole on the probe until the waveform changes to be correct as the figure above 1 Horizontal Control 6 Universal Knob 11 Function Menus 16 Probe Compensation Ground Terminal 2 Auto Setup 7 Trigger Control 12 MATH Function 17 USB Host 3 Run Stop 8 Decode Control 13 Ref 18 Digital Channel Inputs 4 WaveGen 9 Digital Channe
4. as to Check if the attenuation coefficient of the current channel make a good waveform displaying matches with the attenuation ratio of the probe SIGLENT as soon as possible and return the 2 rage ea bear rn ean ill i cause instrument to the factory to have it repaired by 4 There is waveform displaying but not stable ns ee qualified personnel authorized by SIGLENT a DISPLAY is Vectors Please turn the Type to 4 Restart the instrument after completing inspections 1 Check the trigger source check whether the Source Dots to solve the problem above in menu of TRIG is the actual operating channel Gean 5 If it still does not work normally please contact 2 aha ie waveform E a is sec tee se 7 USB storage can t be recognized lock hole SIGLENT PAER ACANTONAR OAS Ine tee When ang 1 Check if the USB flash disk can work normally frequency signal is connected to the instrument 2 Check if the USB Device Host can work normally 2 After the signal is sampled there is no corresponding You d better make sure that the current time base is 3 Make sure the USB disk being used is of flash type waveform displaying correct the instrument does not support USB of hardware type 4 Make sure the system format of used USB disk is FAT32 5 Restart the instrument and then insert the USB to check it 6 If it is still in abnormal use please contact with SIGLENT 3 Check the trigger type Edge
5. setting the serial 1 or 2 to I2C type in trigger menu you can use universal knob to set to trigger on start stop condition restart no ack EEPROM or on the read write frame with specific device address and data value During I2C trigger settings it is essential to set source channel previously in decode menu In the figure below the trigger condition is set to start channel 1 is set as Data signal channel 2 is set as Clock signal SIGLENT Trigd M500us Delay 244 0us v Sa 1 000Gsa Curr 700K pts 1X IMO G 2 00 Vidiv 1x MO DC 11100 Yidi SDS2000 Quick Start 9 SIGLENT SIGLENT SPI Trigger Vertical Control a a Nor j i After setting the serial trigger to SPI type in trigger menu ail Press the button to set to Normal trigger mode VERTICAL Vertical Scale Modify the vertical scale of current you can select to trigger on MISO data or MOSI data aii i T locka d h le whil The data length are variable to set from 4 to 96 v Press the button to set to Auto trigger mode waveform Turn clockwise to ecrease t re scale while i turn counterclockwise to increase it During the modification s the amplitude of the waveform will enlarge or reduce and Single Press the button to set to Single trigger mode SARLIN EE Trigger ly ia the scale message at the right side of the screen will also After setting the serial trigger to UART RS232 type in x change Press down the knob to quickl
6. trigger level value of the current waveform Press down the knob to reset the parameter to zero 11 12 13 Trigger Type PA Display the currently selected trigger type and trigger condition setting Different labels are displayed when different trigger types are selected For example means triggered on Slop side in edge trigger Channel Setting Probe Attenuation Factor Display currently selected probe attenuation factor All factors are 1X 5X 10X 50X 100X 500X 1000X Channel Coupling Display the selected coupling mode of the current channel All modes are DC AC GND Voltage Scale 1 00V div Represent the voltage value of each grid on the vertical axis of the screen Use POSITION knobe to modify the parameter which is variable from BW Limit E If the current BW Limit is On then the mark BJ displays When the vertical scale is 2mV div the BW Limit turns on automatically Impedance Display currently selected impedance 1MQ 50Q of the channel Trigger Level Position Display position of the current channel trigger level Press down the konb to reset the level to vertical center of the screen Menu Display menus of the currently selected function module Press any menu softkey to perform corresponding setting SDS2000 Quick Start 17 SIGLENT SIGLENT i N Run Stop J Using Security Lock Troubleshooting 2 Check if the signal connecting cord is correctly 5 No display after pressi
7. trigger suits to general signal and Video trigger suits to video signal Only in correct trigger type can the waveform stably displays 4 Change the setting of trigger holdoff 1 Check if the probe is correctly connected to the signalconnecting cord 18 SDS2000 Quick Start SDS2000 Quick Start 19
8. ERNOD aes ec cents a E EEE 14 Function MENUS ssssessessessseesneestsssensseessnecnsenseseessesssessauesensnscnstsccensousnecanesonuessusnesanesnaenosuenees 14 General Inspection User VALET CE seeniori Ee Epe eee stetitactoes 16 USING SE GUN LOCK arsane EA ES EA E 18 1 Inspect the shipping container 2 TOU SS INO UNO mareen E E S ern RNE 18 Keep the damaged shipping container or cushioning material until the contents of the shipment have been completely checked and the instrument has passed both electrical and mechanical tests wWWrgg The consigner or carrier will be responsible for damages to the instrument resulting from shipment SIGLENT would not provide free maintenance or replacement ICE 2 Inspect the instrument If there are instruments found damaged defective or failure in electrical and mechanical tests please contact SIGLENT 3 Check the accessories Please check the accessories according to the packing list If the accessories are incomplete or damaged please contact your SIGLENT sales representative WW8z Figure 2 TopView SDS2000 Quick Start 1 IV SDS2000 Quick Start Adjust the Supporting Legs Adjust the supporting legs properly to use them as stands to tilt the oscilloscope upwards for stable placement as well as easier operation and observation of the instrument Before adjusting After adjusting 2 SDS2000 Quick Start SIGLENT Connect to AC Power Supply The oscilloscope
9. F SIGLENT IGLE OLOGIES f SIGLENT 8082304 ows Quick Start SDS2000 Series Digital Oscilloscope gt Persien ene Partien nam a TE H e 7 X po J 9 Y ae pal kb Q A j CH2 masm me sk QS01020 E02A SIGLENT Copyright Information SIGLENT TECHNOLOGIES CO LTD All Rights Reserved Declaration SIGLENT products are protected by patent law in and outside of P R C SIGLENT reserves the right to modify or change parts of or all the specifications or pricing policies at company s sole decision Information in this publication replaces all previously corresponding material Any way of copying extracting or translating the contents of this manual is not allowed without the permission of SIGLENT Note SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO LTD Contact us SIGLENT TECHNOLOGIES CO LTD Address 3 F building NO 4 Antongda Industrial Zone 3rd Liuxian Road Bao an District Shenzhen P R C Tel 86 755 36615186 E mail sales siglent com Hitp www siglent com SIGLENT General Safety Summary Carefully read the following safety precautions to avoid any personal injury or damage to the instrument and any products connected to it To avoid potential hazards please use the instrument as specified Use Proper Power Line Only the power cord designed for the instrument and authorized by local country could be used Ground the Instrument The i
10. a RAA ee ari a nce ios ea ggg RR I Safety Terms ANd SymbolS cceeeeeesseessseeeeeee cent eeensessneceeeeeeeeeenensnessreceteceeeeeensensessrocneeeeees II General Care And Cleaning eeeseeseeesseesseesserssnessrrnsnensnennn enes enn tenn enn enes ne nn tenn renen ennen nen nen nanna II 1 Quick start GMerall IMSPECtion fer RNA R RARE REA RR AREAN AE NA A RR SORAN Appearance and Dimension s sssssrssessesesesesrsenennnnananenenenennnnn nana ennen non nen menemen nenene nan 1 AJUS TRES Ue 970 at 010 ES OS aaa 2 Connec ie AG POWer Sumy Sess es rece ata RR eee eae eee eee 2 Power on INSPCCtION 2eeeree ee eeeee eee e ect te eee e eee eetneee eee e tear ennen enn ennen ennen ennen nn nn nens nn nn 3 FORNE CH ING P OWE dekide uuina ka sce aresreenceeeaveie deur ueiece teens rt RIS ARENAN 3 FURGHON INS DOG N T esse rosetten ters Ner Eees 3 Probe Compensation e eeeesssssssnrrrrrrrnrsnnnnnnrnrrrnnnrnnsnnnernnrrnnnnrnnnnn etern nrnnnnnnn nn nn enn renen nte nn 4 The Front Panal eer nr eer enn en nee eee 5 TMe FSET AN teense ee eee eal tee ai aiea erence 6 HTT OGUCTION OF Eaei mn e a rr 7 Horizontal Control Tr Lee Tere a E RR E I ere ee Lee RE V re a TE T 7 Iii eie cga girre RR ARA 7 Ceac ES OM 00 Nee oe a a ae a ara ae 11 SDS2000 Quick Start III SIGLENT SIGLENT Ege CONTO rer ere een er ere eee meets ent seer en eeee on ener ee eee eer eet ene ne tenn eee fern ee 13 Quick start Appearance and Dimension RIVETS a
11. accept 100 240V 45 440Hz AC power supply Please use the power cord provided as accessories to connect the instrument to the power source as shown in the figure below Power Socket Note In want of replacing the fuse please return the instrument to the factory that produced it to have it repaired by qualified service personnel authorized by SIGLENT SIGLENT Power on Inspection When the scope is energized turn on the power switch at the lower left corner on the front panel During the start up process the instrument performs a series of self test items and you can hear the sound of relay switching After the self test completed the User Interface displays immediately Connect the Probe SIGLENT provides passive probe for the SDS2000 series oscilloscope Please refer to corresponding Probe User Manual for detailed technical information Connect the probe 1 Connect the BNC terminal of the probe to one of the channel BNC connector of the front panel 2 Connect the probe tip to the circuit point to test and the ground alligator clip of the probe to the ground terminal of the circuit Function Inspection 1 Press Default to restore the oscilloscope to its default setup 2 Connect the ground alligator clip of the probe to the Ground Terminal on the front panel Compensation Signal Output Terminal Ground Terminal 3 Use the probe to connect the CH1 Input Terminal and the Compensation Signal
12. ef waveform Turn clockwise to decrease the scale while turn counterclockwise to increase it During the modification the amplitude of the waveform will enlarge or reduce and the scale message at the middle of the screen will also change In addition the knob can be used to select a digital channel SIGLENT Run Control RUN CONTROL lt Defa ut Waye Wave P con Press the button to open the WaveGen menu at te Press the button to reset the oscilloscope to its default setup The default voltage scale and timebase are aan respectively 1V div and 1us div SDS2000 provides built in signal generator function Ten types of signal including Sine Square Ramp Pulse DC Noise Cardiac Gaus Pulse Exp Rise and Exp Fall are supported The most output frequency is 25MHz setting function The oscilloscope will automatically adjust In addition the insrtument can output any waveforms by the horizontal time base vertical scale and trigger mode connecting EasyWave software through remote conrtol according to the input signal to make the waveform displays in a perfect state Press the button to enable the waveform auto Sas Stop _ Press the button to set the state of the instrument to RUN or STOP In RUN state the indicator light displays yellow In STOP state it displays red SDS2000 Quick Start 13 SIGLENT Universal Knob Intensity Adjust Adjust Wavefo
13. ess again to turn it off 4 gt Horizontal POSITION Modify the trigger position The waveform will move left or right when you revolve the knob Meanwhile the Delay value will also increase or decrease as the the waveform moves Press down the knob to return the waveform to horizontal center of the screen S Horizontal Time Base Modify the horizontal time base Turn it clockwise or counterclockwise to reduce or increase the time base The waveform will display expanded or compressed and the time base message at the upper left of the screen will change as the time base changes Trigger Control TRIGGER Auto Setup omar sire Press the button to open trigger menu This oscilloscope provides various trigger types Edge Slope Pulse Video Window Interval DropOut Runt Pattern and Serial Bus l2C SPI UART RS232 CAN LIN We will introduce Video Interval Runt Pattern and Serial Bus trigger in the following HDTV Video Trig ger Analog video signal includes NTSC and PAL and HDTV signal are supported in SDS2000 oscilloscopes In video operation you can select Custom to set any line and field SDS2000 Quick Start 7 mm I Interval Trigger The time interval from the rising edge or falling edge of input signal passes through the trigger level to the next rising edge or falling edge passes through the trigger level and the currently set time satisfy the Limit Range lt gt
14. l Control 14 Channel Vertical Control 19 Function Menu Softkeys 5 Default Setup 10 MATH Ref Vertical Control 15 WaveGen Output 20 Analog Inputs 21 Power On Off 4 SDS2000 Quick Start SDS2000 Quick Start 5 SIGLENT The Rear Panel 1 Handle Pull up the handle vertically for easy carrying press it down if you do not need the handle 2 EXT TRIG Connector 3 Pass Fail or Trig Out Output Via this interface the oscilloscope can output a signal that can reflect the current capture rate of the instrument at each trigger or a Pass Fail pulse I S I ea U a EE Ca a E E a A i E err SSS EE 4 LAN Interface The instrument can be connected to network via this interface to perform remote control 5 USB Device PictBridge printer or PC can be connected via this interface to print the current interface of the oscilloscope or control the instrument through PC software 6 Lock Hole You could lock the instrument in a fixed location using a security lock please buy it yourself via the lock hole 7 AC Power Socket The standard power supply for the instrument is 100 240V 45 440Hz Please use the power cord provided as accessories to connect the instrument to AC power 6 SDS2000 Quick Start SIGLENT Front Panel Function Brief Horizontal Control Press the button to open waveform display mode menu The selectable modes include X Y Y T ROLL Press the button to open delay sweep function Pr
15. n to horizontal center of the screen 16 SDS2000 Quick Start SIGLENT Product Logo SIGLENT is the registered trademark of our company Channel Label Waveform Different channels are marked by different colors and the color of the waveform complies with the color of the channel 3 Working state Available states include Arm Ready Trig d Stop Auto Horizontal Time Base Represent the time of each grid on the horizontal axis of the screen You could revolve ns to modify the parameter which is variable from1ns gt 50s SIGLENT 6 Trigger position Display the trigger position of the waveform on the screen 7 USB Device Interface Mark Indicate the current set of USB Device Interface If the icon displays m the interface is set to USBTMC if the icon display E the interface is set to Printer 8 Frequency Counter Display the firmware frequency of current waveform 9 Sample Rate Memory Depth Display the current sample rate and memory depth of the oscilloscope Use horizontal SCALE knobe to modify the parameter 10 Trigger Setting Trigger Source CH Display the trigger source currently selected Different labels are displayed when different trigger source are selected and the color of the trigger parameter area will change accordingly Coupling Mode Hl Display coupling mode DC AC LF Reject HF Reject of the current trigger Source Trigger Level L 0 00mV Display the
16. ng connected to BNC Check whether the trigger Mode is Normal or Single If needed you could use the security lock please buy it The general failures and consequential solutions are 3 Check if the probe is correctly connected to the and if the trigger level exceeds the waveform range If yourself to lock the instrument in a fixed location The listed below When you find them please deal with them item under test yes set the trigger level to the middle or change the method align the clock with the clock hole and plug it into in the following corresponding ways If the problem 4 a n ae are signal generated trom the item trigger Mode to Auto under test the lock hole vertically turn the key clockwise to lock the proves to be unsolvable by yourself please contact with 5 Pesamnle eind Note press Auto Scale could automatically replace the instrument and then pull the key out SIGLENT as soon as possible p gna above setting 1 The screen remains dark after power on 3 The voltage amplitude measured is higher or lower than the actual value the error usually occurs in use of 6 The waveform displays like ladder 1 Check if the power is correctly connected the probe 2 Check if the power switch is faulted 3 Check whether the fuse is burned out If the fuse needs to be changed please contact with 1 The horizontal time base may be too low you can increase it to improve the horizontal resolution so
17. nstrument is grounded through the protective earth conductor of the power line To avoid electric shock please make sure the instrument is grounded correctly before connecting its input or output terminals Connect the Signal Wire Correctly The potential of the signal wire is equal to the earth so do not connect the signal wire to a high voltage Look Over All Terminals Ratings To avoid fire or electric shock please look over all ratings and sign instruction of the instrument Before connecting the instrument please read the manual carefully to gain more information about the ratings Use Proper Overvoltage Protection Make sure that no overvoltage such as that casued by a thunderstorm can reach the product or else the operator might expose to danger of electrical shock Electrostatic Prevention Operate in an electrostatic discharge protective area environment to avoid damages induced by static discharge Always ground both the internal and external conductors of the cable to release static before connecting Keep Well Ventilation inadequate ventilation may cause increasing of temperature which will eventually damage the instrument So keep well ventilation and inspect the intake and fan regularly Avoid Circuit or Components Exposed Do not touch exposed contacts or components when the power is on Use Only the Specified Fuse Do Not Operate Without Covers Do not operate the instrument with covers or panels removed
18. rm Intensity Grid Brightness Transpanrency In non menu operation mode menu is hidden turn this knob to adjust waveform intensity 0 100 Turn clockwise to increase the brightness and counterclockwise to reduce You can also press Display Intensity and use the knob to do adjusting To adjust grid brightness 0 100 or transparency 20 80 please operate in the same way as waveform intensity Universal Knob In menu operation when the light below the knob is lighted you could revolve the knob to select between submenus under the current menu and press it down to select the current submenu In addition it can also be used to modify parameters and input filename 14 SDS2000 Quick Start Function Menus set waveform Type Color Persist Clear Display Grid Intensity Brightness and Transperancy Transperancy indicates the display transperancy of any popup messagebox For instance you could use universal knob to adjust transperancy of the messagebox when Cursor Measurement is on Press the button to enter the utility menu to set system related functions or parameters such as IO Set Sound language In addition some advanced functions such as Pass Fail test Print Setup Do Self Test and Update are also supported then press down any menu to display corresponding help information To display the submenus help information of the current menu firstly you should open the current menu and then pres
19. ror During the modification the waveform will move up and down and the position message at the lower part Notes for more trigger types and corresponding operation of the screen will change along Press down the knob information please refer to the trigger chapter of to quickly reset the vertical position to zero SDS2000 User Manual 10 SDS2000 Quick Start SDS2000 Quick Start 11 SIGLENT Decoding for 12C signal of 7 address is described in the following figure Digita Digital channel function button Press the button to open digital channel menu SDS2000 supports 8 integrated digital channels Math Press the button to open math operation menu under which the operation of adding subtracting multiplying dividing FFT integral differential and sqare are supported 12 SDS2000 Quick Start oe Press the button to enable the reference waveform function thus to compare the current waveform with the reference waveform to decide circuit failures SDS2000 supports 4 reference waveforms saving Vertical POSITION Modify the vertical position of Math Ref waveform Turn clockwise to increase the position while turn counterclockwise to decrease During the modification the waveform will move up and down and the position message at the lower part of the screen will change along Press down the knob to quickly reset the vertical position to zero Vertical Scale Modify the vertical scale of Math R
20. s down the HELP button the last step is to select any submenu you want Press the button to enable print function If the instrument is connected to a printer which is usable press it to perform print function Press the button to enter the measurement setting menu You could set measurement setting Statistic function and all measure In measurement setting you could select as many as five parameters and display them simultaneously on the screen In Statistic function the curent value Mean value Min value Max value Std Dev and Counts are displayed on the screen In all measure you could display all Voltage Time Delay parameters by pressing the corresponding softkey SIGLENT Press the button to enter the sample setting menu to set the acquisition mode Normal Peak Detect Average High Res dot inserting mode and memory depth 7K 14K 70K 140K 700K 1 4M 7M 14M Press the button to enter the file save and recall function menu the storable file types includes Setups Waveforms Picture and CSV SDS2000 Quick Start 15 User Interface SIGLENT M 5001s Delay0 00ps 2 5 Trigger Position Use horizontal POSITION Oo knob to modify the parameter Turn clockwise or counterclockwise to make the waveform move right or left which will respectively cause the Delay parameter to decrease or increase Press down the knob to automatically reset the parameter to zero as well as make the waveform retur
21. y switch the vertical trigger menu you can select to trigger on start stop Level Modify the trigger level Turn it clockwise scale adjustment modes between Coarse and Fine checksum error or data The data width are variable to set from 5 to 8bits or counterclockwise to make the level move up or down In the meanwhile the level value displayed at the upper ee CAN Trigger right of the screen will increase or decrease Press it are marked by different colors which are also used to NS Decoding function button down to quickly reset the trigger level to the vertical center mark both the waveforms on the screen and the a PERSER After setting the serial trigger to CAN type in trigger of corresponding waveforms channel input connectors Press channel button to rress it to open decode menu menu you can select to trigger on start remote ID open the corresponding channel and press again to SDS2000 supports two serial buses ID DATA or Error of CAN H or CAN L signal fore including 1 and 2 for analog signal Variable CH1 CH2 CH3 CH4 decoding LIN Trigger Vertical POSITION Modify the vertical position Position The protocols includes 12C SPI ae a 7 y ART RS232 CAN and LIN After setting the serial trigger to LIN type in trigger menu of current waveform Turn clockwise to increase the U RS232 CAN and LIN you can select to trigger on Start ID ID DATA or position while turn counterclockwise to decrease Data Er
Download Pdf Manuals
Related Search