VTP-1A Series Installation Instructions
Contents
1. North American standards FCC Compliance GE Security Inc HQ and regulatory responsibility GE Security Inc 8985 Town Center Parkway Bradenton FL 34202 USA EU authorized manufacturing representative GE Security B V Kelvinstraat 7 6003 DH Weert The Netherlands C EG N4131 UL 60065 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of2. as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info
3. camera to the BNC input of the GE passive transceiver e Connect the ground screw connector to a qualified earth ground using a short thick wire GEC PVTC FCSP GEC PVTC MSP e Connect the UTP to the terminal block of the GE transceiver Active Transmitter e Connect the baseband video output of the camera to the BNC input of the GE active transmitter e Connect the UTP to the terminal block of transmitter e Connect the ground screw connector to a qualified earth ground using a short thick wire e Set the distance switch to HI for distances longer than 3 000 feet and set it to Low for distances equal or less than 3 000 feet Power e Connect a qualified 12 VDC or 24 VAC power supply cable to the transmitter s input power terminal block for the GEC 1AVT Control Room Installation UTP e Connect the UTP wires carrying video signals to the terminal block input of the active receiver e Make sure that the same UTP pair and polarity are used on both transmit and receive sides Video e Use the provided 75 ohm patch cord to connect the BNC video inputs of video receiving devices such as DVRs or matrix switches Make sure that your video receiver device s input is set to 75 ohm Power e Connect the ground screw connector to a qualified earth ground using a short thick wire e Connect a qualified 12 VDC or 24 VAC power supply cable to the input power terminal block for the GEC 1AVR AVC 4 Note This product is intended
4. has been dropped CAUTION T RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Awenn To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Inana This apparatus is a Class product This product must be connected to a mains socket outlet with a protective earthing connection A WARNING The mains plug is used as the disconnect device and shall remain readily operable Important Safety Warnings e Installation should be made by a qualified service person and should conform to all local codes e DO NOT bundle UTP signals in the same conduit as high voltage wiring e To reduce the risk of fire or electrical shock do not expose these products to rain moisture dripping or splashing e No objects filled with liquids such as vases shall be placed on GE equipment e DO NOT block ventilation openings to let sufficient airflow to the UTP devices e DO NOT install the unit in a place where the operating ambient temperature exceeds 122 F 50 C e Only unplugging the power cord is considered as a main power disconnect e Make sure that the mains Voltage input is set to the proper local
5. voltage Before powering up the unit connect the ground terminal to a qualified earth ground through a short thick wire Wiring Technical Notes These technical notes should all be considered prior to installing these devices e Use point to point unshielded twisted pair wire 24 16 AWG 0 5 1 3 mm stranded or solid Category 2 or better e The video signal may coexist in the same wire bundle as other video telephone data control signals or low voltage power You can run GE video signals in or near electromagnetic fields in accordance with National Electrical Code local or other local safety requirements e DO NOT USE SHIELDED TWISTED PAIR WIRE Multi pair 8 pair or more wires with an overall shield are fine e DO NOT USE UN TWISTED WIRE e DONOT place a transmit and a receive signal in the same wire bundle It may cause interference e DO NOT send Up the Coax Pan Tilt Zoom signals through active amplified GE transmitters or receivers Passive GE transceivers can transmit video and Up the Coax P T Z control signals up to 750 ft 228 m e Werecommend using short 18 AWG solid wires for ground connections e GE VPD products follow the EIA TIA 568 standard There are two wire color code standards EIA TIA 568A and EIA TIA 5688 Either standard can be used for making connections as long as the RJ 45 jacks at both ends of each cable follow the same standard e Measure wire distance by 1 Shorting the two conductors toge
6. GE Security Introduction The GEC 1AVR AVC 4 is a single channel active UTP receiver that provides high resolution color or black and white video over unshielded twisted pair wires of category 2 7 at distances up to 4 000 feet 1 220 m when is paired with GEC 1AVT GE active transmitter It can be used with any GE passive transceiver for distances up to 2 000 feet 610 m The GEC 1AVR AVC 4 features GE s Automatic Video Compensation AVC technology The AVC incorporates a sophisticated microprocessor controlled analog circuit that continuously analyzes the incoming video signal and compensates for cable attenuation independent of video signal content It has a built in distribution amplifier to provide two independent video outputs The GEC 1AVT is an active UTP transmitter It is equipped with a 2 position switch to adjust for distance These single channel active devices are compact in size and easy to install Their integrated ground loop isolation prevents disturbing hum bars common with long distance installations and its excellent crosstalk and noise immunity provides quality video up to the maximum distance They are equipped with built in surge suppression on the UTP input to protect video equipment against damaging voltage spikes These active devices are unidirectional and do not support Up the Coax Pan Tilt Zoom telemetry signals Any unused pair of UTP cable can be used for transporting telemetry signals IMPORTANT SAFETY INS
7. TRUCTION 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not block any ventilation openings 8 Install in accordance with the manufacturer s instructions 9 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including DVRs that produce heat 10 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wider blade or the third prong are provided for your safety If the provi led plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 11 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 12 Only use attachments accessories specified by the manufacturer 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatis has been damaged in any way such as a power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or
8. ther at the far end and measuring the loop resistance by an Ohmmeter 2 Use the Loop Resistance table to calculate the distance e DO NOT connect coax cables longer than 100 ft 30 M to the BNC connectors of any GE UTP equipment e All measured distances should include any coax cables in the path e Verify camera current requirements and wire resistance limits for the maximum distance that power can travel Use the Power Distance Chart to verify the wire distance e GE VPD products require Unshielded Twisted Pair UTP wires Category 2 or better 24 AWG 0 5 mm or thicker Table 1 Loop Resistance per 1000 feet Artie lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shack to persons Av tre exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and Maintenance instructions in the literature accompanying the appliance P N 1069767 REV 1 1 ISS 29APR10 Wire Type Resistance 24 AWG 0 53 mm 52 ohms 23 AWG 0 57 mm 42 ohms 22 AWG 0 64 mm 33 ohms Single Channel AVC Active Receiver and Transmitter Installation Sheet GEC 1AVT GEC 1AVR AVC 4 Camera End Installation Video Passive Transceiver e Connect the baseband video signal output of the
9. to be supplied by a UL Listed Direct Plug In Power Unit marked Class 2 or LPS and output rated 12 VDC 1 Amp minimum Application Drawings Single Channel Passive to Active Mid Range Application a a 2 000 ft 610 m Cat5 SEEPEALE e REE JA on GEC PVTC MRTSP GEC 1AVR AVC 4 Single Channel Active to Active Long Range Application Oo Lt 4 000 ft 1 220 m Cat5 Le igo GEC 1AVR AVC 4 GEC 1AVT Technical Specifications Electrical Regulatory information Video Format Frequency Adjustment Coax Twisted Pair CMRR Power Power Indicator NTSC PAL SECAM 20 Hz to 6 MHz Automatically controlled by internal microprocessor 75 Ohm 100 Ohms 20 24 AWG min unshielded Category 2 7 up to 750 ft 228m 70 dB 12 VDC 24 VAC 140 mA max Red LED Connectors UTP Inputs Screw less terminal blocks Video Outputs BNC Power Screw less terminal blocks Mechanical Material ABS plastic UL rating of 94V 0 Dimensions W x H x D 2 9 x 1 69 x 1 in 74 x 41 x 25 mm Weight Environmental 1 5 oz 40 g Humidity Temperature 0 to 95 noncondensing Operating 10 to 50 C Storage 30 to 70 C Specifications are subject to change without notice Included Accessories e UL Listed Direct Power Unit output rated 12VDC 1 Amp minimum e 2 Philips mounting screws Manufacturer Regulatory information
Download Pdf Manuals
Related Search