Home

PD – 2600 / 2601 / 2602 / 2603 Series User`s Manual

1. screw The screw bosses of PD 2601 base pp 7601 Base e should now align with the screw holes on aie ra sidewall of system chassis Only 1 screw ears needs to be applied Use the self tapping _ h aJe screw that comes with PD 2601 to fix from C e side of sidewall as demonstrated in Outside of sidewall ix 6 Connect interface cable Carefully close back the top cover of HT or PB system and connect the interface cable of PD 2601 to appropriate port in system connector area Then close the back cover of the system INSTALLING PD 2602 Opening the rear connect cover on system To install PD 2602 to the base of KS or TP systems the rear connect cover on its base has to be removed as described in the user s manual The plastic hook plate to remove the rear connect cover in slim base is indicated in Pix 7 and that for universal base is indicated in Pix 7 Pix 8 Part 6 Fixing pole display base to system To fix the PD 2602 to base of KS or TP systems please connect the interface cable of PD 2602 through the cable exit in base as in Pix 9 a peeping view of pole display joint base bottom Pix 9 to the appropriate port in main unit passing the inside of system base as indicated in the top view picture Pix 10 Match the pole base joint mechanism to the system rear connect area Fit 2 screws through washers at arrowed points to hold the joint tight INSTALLING PD 2603 Open back cover on system First push in the circle
2. the circled knobs on both sides as in Pix 1 to remove the back cover Take out the arrow pointed pole cover from it Opening the top cover of system Prepare a piece of clean soft clothe of appropriate size in front of the HT system to prevent damage Turn the display panel to straight up position For both HT and PB Pix 1 system push in the rectangular marked spring button in Pix 1 on both sides of chassis and raise the rear edge of the top cover The COM port DC support can be set at this moment Find joining points on system Pix 2 Refer to Pix 2 that is a picture of the HT or PB chassis near the right bottom corner as you are facing the HT or PB system from its back with several portions enlarged around please find 2 rectangular PD installation holes A on the bottom chassis 2 circular locating holes B on I O plate and 2 circular screw holes C on metal sidewall Find joining points on pole display base Part 4 Pix 3 Take PD 2601 out of its box and refer to Pix 3 that is a picture of the pole display base unit lowest part of the PD with 2 enlarged portions to the right and a slightly enlarged side view picture to the left to find 2 bottom locking lugs A 2 short cylindrical locating bosses B to fit into I O plate and 2 plastic screw bosses C on side Please note that the PD cable comes out of the bottom end of the base tube yet in the illustration pictures the cable is eliminated for sake of minimum vis
3. DP Defeat mode Ove User defined font A A YES i O O Auto eroll message NO NO No ves yes YEs eT DRIVER INSTALLATION For application software to use RS232 interfaced PD 260X there is no direct need for any driver The OPOS OLE POS driver or the JPOS Java POS driver would be required for OPOS or JPOS programs and the PD 260X would have to be set to Epson command mode These drivers are available from our web page http www posiflex com tw Download 20list asp Status 1 amp Series_Name U POS amp Model_Name OPOS and execute the file SETUP EXE to install the OPOS Control Manager To add the customer display under OPOS control please set in OPOS Control Manager device name PD2x Line Display in the top row For RS 232 models select the COM port in the 3 row and set baud rate to 9600 in 4 row as in the left sample screen below Select USB in 3 row for USB interface models as in the right sample picture below For USB interfaced PD 260X please visit our web site and find the driver from the class PD23_26U The guidance for each function call in the library USBPD dll is covered in the ReadMe file in that class N N Tending code change N N N Part 9 SPECIFICATION OPTICAL Number of digits 20 digits row 2 rows Dot matrix 5 X 7 dots Digit height 9 03 mm Digit width 5 25 mm Display color Blue or Green MECHANICAL Total Height PD 2600 410 mm Total W
4. POSIFLEX PD 2600 2601 2602 2603 Series User s Manual Rev CO FCC Notes This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improp er application About This Manual Posiflex has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise damages including without limitation loss of data or profits
5. acters each Support 12 international character sets of 12 characters each e Simple installation e Selectable between Serial RS232 interface model and USB interface model e Supports UPOS 1 8 and is WEPOS ready e Case color choices ivory black for HT terminals or black for FT KS and TP terminals Part 2 INSTALLATION GUIDES HOST SYSTEM PREPARAION For serial interface RS232 PD 2601lor PD 2602 or PD 2603 to be used in HT or PB or KS or TP or FT series you have to adjust during power off the internal jumper of the host system to supply 5 V DC to the COM port selected for the serial interface pole display This adjustment has to be done by a qualified electronic technician following guide from relevant technical manual The default communication protocol should be set to 9600 bps none parity 8 data bits 1 stop bit with hardware handshaking on CTS The power for the USB interface type pole display is supported through the USB connection However should these customer displays are to be connected through an USB HUB instead of a direct USB port of the system the HUB must be powered by a separate power adaptor otherwise there could be the power shortage problem INSTALLING PD 2600 In base of stand alone models PD 2600 models only looking from rear side of the bottom the connector area will look like below For serial RS232 interface models To Display head RS232 In 12 VAC In The RJ45 type modular connector is for interna
6. d a knobs on both sides as in Pix 11 to remove the back cover A Remove pole cover Pix 11 Remove the pole cover on rear edge of the base top cover of FT system by first removing the 2 arrowed screws in Pix 12 and then pushing the wedge shaped pole cover up Install PD and connect interface cable Insert the base of PD 2603 PD 2603U from top of FT system base with the flat side of the pole base facing the back cover direction and screw back the 2 screws as in Pix 13 Connect the interface 5 cable to appropriate port Pix 13 COMMAND EMULATION MODE SETUP DIP switch window a Pix 14 Now please check the back of PD 260X display head as in the left picture in Pix 14 There is a small piece of plastic cover for the DIP switch window Slide the cover downward but don t pull it off otherwise you may have to practice for inserting it back You can find 6 positions of DIP switches Part 7 in this window Adjust for the appropriate command mode used by the application program according to below table Switch position counts from left to right and ON means pushed up as indicated in the right part in Pix 14 aaa ie aesae Ie The factory default command mode is set to Noritake mode for normal delivery Please change it to Epson mode if OPOS or UPOS driver is used for the application program POWER ON SIGN With interface cable connection well installed and with COM port power set for s
7. erial models turn on the HT or KS or TP Posiflex POS system a firmware identifier as power on sign will appear on the pole display screen for a while to indicate that pole display is self tested O K and ready to work USING THE CUSTOMER DISPLAY INTERRFACE SELECTION This series of customer display is designed to serve in HT KS TP FT series Posiflex POS systems with RS232 interface models and with USB interface modek It is advisable to well study the I O port availability of the host system before determining which interface model to be used When a RS232 serial interface model of PD 2601 2602 2603 is used the jumper on main board of HT KS TP FT system must be modified to supply power to the COM port designated for PD 2601 2602 2603 Whenever the RS232 interface PD 2601 2602 2603 is to be removed from the HT KS TP FT system consequently the jumper has to be changed back to neutralize the COM port otherwise damage could occur The USB interface model of PD 2601 2602 2603 should be connected directly to an USB port and must not be through any non self powered USB HUB to get power through the USB port itself and there is no need for other special arrangement COMMAND MODE SELECTION GUIDE The below table provides some comparison for selection on command mode to be used in the application program if it is not yet determined Part 8 Blinking Cursor N N A Invisible Blinking Blinking Block Block Block
8. idth PD 2600 220 mm Total Depth PD 2600 110 mm Total Height PD 2601 392 mm Total Height PD 2602 325 mm Total Height PD 2603 375 mm Display Head Height 57 5 mm Display Head Width 196 6 mm Display Head Depth 39 5 mm Case color Black or Ivory ELECTRICAL Power frominterface port of FT HT KS TP system 5VDC 1A ENVIRONMENTAL Operating temperature 0 to 40 C Storage temperature 20 to 70 C Operating humidity 20 to 85 non condensing Storage humidity 5 to 90 non condensing WARNING If the user opens the pole display housing to make any modification all the product warranty will be voided NOTE Please refer to Posiflex Product Information CD orDVD or visit our web http www posiflex com tw for further information when needed Part 10
9. l use and is already occupied The RS232 input port is a DB9 female connector Connect the attached RS 232 signal cable to this port and one of the COM port in the host system Set the RS 232 communication protocol for this port to 9600 bps no parity 8 bits 1 stop bit with hardware handshaking Connect the power adaptor to the rightmost power connector Turn on the switch in the front side of the base For USB interface models USB To Display head 424 V DC Out 24VDCIn 12 VAC In The RJ45 type modular connector is for internal use and is also already occupied Connect the B type connector of the interface cable to USB in connector area and the A type end to USB port of the host Insert the 2 pin or 3 pin power connector from either 12 V AC or 24 V DC power Part 3 adaptor to the 12 V DC In or 24 V DC In jack in the connector area Insert either end of the power cable to 24 V DC Out jack in the connector area and insert the other end to the power connector of Posiflex POS printer if needed Be sure to hear a click at each connection to obtain a firm contact You may now place the base on a horizontal surface and prepare to power on and adjust the direction of the display head for best viewing effect in application INSTALLING PD 2601 Opening the back cover on system For ease of PD 2601 installation operation the HT K main unit or PB system has to be opened with sufficient precautions First push in
10. r respective holders P N 19460901140 Part 1 BRIEF INTRODUCTION THE PRODUCT The PD 2600 is a stand alone pole mount customer display designed for discrete POS applications The PD 2601 is a pole mount customer display option designed for Posiflex HT series POS terminals and also the PB series discrete systems The PD 2602 is a pole mount customer display option designed for Posiflex KS or TP series touch POS terminals The PD 2603 is a pole mount customer display option designed for Posiflex FT series touch POS terminals It is delivered in separate carton for HT PB KS TP FT series and shall be installed per instruction in this manual FEATURES e Bright VFD vacuum fluorescent display with green or blue filter e Rear mount Pole Display for Posiflex HT series hybrid terminals or PB series discrete systems or KS or FT series fan free touch POS terminals or TP series touch POS terminals e Two line display with 20 characters per line e Adequately large characters for easy viewing 9 03 mm by 5 25 mm e Long life and trouble free operation e 15 30 and 45 adjustable viewing angles Total height 410 mm Stand alone Total height 392 mm PD 2601 on base of HT and PB series Total height 325 mm PD 2602 on base of KS and TP series Total height 375 mm PD 2603 on base of FT series Display frame can rotate horizontally 270 freely Various command emulation modes selectable by DIP switch Support 12 Code Pages of 128 char
11. resulting from the furnishing performance or use of this material This information is provided as is and Posiflex Technologies Inc expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Inc the publisher of this documentation Copyright Posiflex Technologies Inc 2008 All brand and product names and trademarks are the property of thei
12. ual confusion Insert bottom locking lugs Pix 4 A Turn the pole display base unit opposite to have the bottom locking lugs A in Pix 3 facing left and now msert the 2 bottom locking lugs A on base unit into the 2 rectangular installation holes A on bottom of HT or PB chassis from the right corner with the pole display slightly inclined to the left as in Pix 4 Please note that both bottom locking lugs A should be completely inserted and come out of the bottom plate of HT or PB system as emphasized by an arrow in the enlarged portion Fit in locating bosses Please always keep a gentle pressure at the bottom end of pole base bottom locking lugs A to the left away from the sidewall of system chassis when moving the upper part of pole toward sidewall and matching the 2 short cylindrical locating bosses B into 2 round holes B in the I O plate Please refer to Pix 5 to see the 2 locating bosses B from inside of HT or PB system Part 5 Pix 5 Please note the importance of keeping the leftward pressure on bottom end of pole display during the process of turning the pole upright and inserting the locating bosses B or even when you want to release the locating bosses B away from I O plate B and turn the upper end of pole display to left to remove the locking lugs A from bottom chassis A Ignorance of this point may damage or even break off the locking lugs A due to improper torque applied Apply sidewall

PD – 2600 / 2601 / 2602 / 2603 Series User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

PD &ndash; 2600 / 2601 / 2602 / 2603 Series User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

PD – 2600 / 2601 / 2602 / 2603 Series User`s Manual