IDL-4802-QuickGuide
Contents
1. In Remote Cabinet The IDL 4802 should be grounded by connecting a 14 or 12 AWG conductor between the grounding screw on the rear panel of the DSLAM refer to below figure and the earth ground or main grounding bar The resistance between the chassis and the grounding bar should be less than 25 Ohm Grounding Screw of IDL 4802 Grounding Screw of IDL 4802 48 Ensure that all power sources to the device are turned off during the installation 2 FAN Cable Connection POWER ee ON OFF 48 Port DSLAM Switch Q PLANET IDL 4802 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 e Lil 13 oooooooooooooooooooooooo 2 O00000000000000000000000 There are two FAN ports on the front panel One is on the FAN card the other is beside the HK port To make the fans work you must use an RJ45 to RJ45 connector cable to connect the two FAN ports FAN Port RJ 45 pin assignment 12345678 EE ka mi i 3 ADSL and POTS Connections The IDL 4802 supports 48 ports ADSL subscribers per box There are four RJ 21 50 pin female connectors on the front panel of the system Two for ADSL lines and two for POTS interfaces To connect the subscriber lines use cables with the RJ 21 50 pin male connectors When installing just plug the end of cable with connector into the LINE and PHONE connectors on the front panel The other end of the cable is generally tied to the MDF Main Distribu2. 4802 Press Enter 4 Cannot find server Microsoft Internet Explorer k File Edit View Favorites Tools Help A gt x e f JO Search Pe Favorites La i WE 28 Address http 192 168 1 1 MPE Step 2 Login the IDL 4802 A login page will appear Please tvpe vour username password and click Sign in The default username password is admin admin Web Interface Login Password Username admin signin a Level 1 SuperUser RAW Management all a Level 2 Engineer RAW Disabled from User Account a Level 3 Guest Read only After you login the IDL 4802 you will see the system information as below LH Svstem Information ACCESS LOGIN L A i LH Access Level System Date FW Boot ActiveDB Cwrent DB Super user 2009 03 27 Partition 1 Parttion 1 Partition 1 i YSTEM MAC Bridge MAC Gigal MAC Giga MAC 00 30 4F 71 53 BD 00 30 4F 71 53 BB 00 30 4F 71 53 BC SYSTEM VERSION Hardware Firmware Software Web Circuit l 48 Cc 0 77B03 0 77B03 Ud 08 26a AnnexA GIGA STATUS Gigal Giga2 LA SYSLED ALM LED Config Enabled Config Enabled Config Disabled e e Step 3 Configure the DSL PVC Go to Bridge 9 Interface Setup 9 ADSL PVC setting screen select the ADSL port and click Create to apply the PVC settings For example create PVC 1 to Port 1 The default VPI VCI is O 35 vet 0 liver 35 Traffic Rx Default LnShaped WI Tx Default UnShaped Vv Encap LLC P
3. 48 Port ADSL 2 24 IP DSLAM IDL 4802 IDL 4802 48 Quick Installation Guide Table of Contents Package CONTENTS arrbiiuknaztiin inea p E Ad tz abitata Eh 3 CO SVS Wy iri ab 4 SoreLV INSEMICHO Mi kisi jtini a A a d kata 6 Hardware FStal AON isa i i e eas sanmumeniNad geen AA 7 1 Power and Ground Connections ai a e aa a 7 2 FAN Caple Connec HON sesin a a o a f i ata 9 o ADSL and POIS Coniettiot aerial 9 4 Uplink Interfaces Connections see eenennnnnenn nn n ne nn ran nn nn tnnEn nn 10 5 Management Port Connection ixreikmigiri ikwiikkkrejoikuiien kin nies EnA 11 Oe Console Port CONNectON ika ai Ea EEA EAE OENE 11 7 Housekeeping Connectio f kanen sia kawta d le i a 11 WEB CONMOULALION irrita aid E a 13 Further information si i iii aka LA a 19 Package Contents IDL 4802 M IDL 4802 Unit x 1 M AC Power Cord x 1 CDxi Quick Installation Guide x 1 M 2 Meter Telco 50 Cable x 4 W Console Cable x 1 M Rack mounting Ear x 2 E Screw Package x 2 IM Connect Tenon x 4 E RJ 45 Cable for Fan x 1 IDL 4802 48 E IDL 4802 48Unit x 1 DC Power Terminal Block x 1 CDxi WE Quick Installation Guide x 1 M 2 Meter Telco 50 Cable x 4 W Console Cable x 1 E Rack mounting Ear x 2 M Screw Package x 2 M Connect Tenon x 4 M RJ 45 Cable for Fan x 1 If any of above items are damaged or missing please contact your dealer immediately Using a power supply with a different voltage rating will damage and void the warr
4. K AIN HKICOM HK2IN HK2COM HK3IN HK3COM HK4IN HKACOM ALMCOM 123456789 10 IIIN Om Amn A w N o Operation diagram of Housekeeping Inputs and Alarm Contact Output Environment Sensor IDL 4802 IDL 4802 ALMO UT A larm Equipment ALMCOM WEB Configuration This section describes how to use Web Configuration Tool to maintain vour IP DSLAM The IDL 4802 contains a HTIP server Vou can login and configure it bv using vour Web Browser Preparation Before attempting to configure the IDL 4802 please ensure as below Set vour computer s IP with the same network segment of the IP DSLAM For example IDL 4802 default MGMT IP is 192 168 1 1 255 255 255 0 Then vou can set computers IP to 192 168 1 x 255 255 255 0 The range for x is from 2 to 253 Internet Protocol TCP IP Properties f General You can get IP settings assigned automatically if pour network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 792 168 4 0 Subnet mask 255 255 255 0 Default gateway Use the following DNS server addresses Preferred DNS server Alternate DNS server Pe Step 1 Using your WEB Browser Open web browser and type http 192 168 1 1 in the browser s address box This IP is the default MGMT IP address of IDL
5. Service lamin ON Service Prottel 1 Spectrum EE Profiel 1 Ja j The Service Profile range from 1 to 120 The Spectrum Profile range from 1 to 120 The TCA Profile range from 1 to 64 port o1 12 w 00 O 2 OFF OFF 1 1 1 eo 3 OFF OFF ii A a O 4 OFF OFF A 4 4 PO 5 OFF OFF 1 4 TR EA E pt oF ai E i ioe 7 OFF OFF 1 4 A L Te TE OFF ki a a j O 3 OFF OFFO T TA a F TO 10 OFF OFF 1 1 1 O 4 OFF OFF 1 1 COE l Step 5 Connect the ADSL2 2 CPE to Patch Panel Connect the ADSL2 2 CPE to Patch Panel and configure it the VPI VCI value must be the same with IDL 4802 After finish setting the CPE will establish the ADSL connection with IDL 4802 You can check the connection status as below figure The Current Status is ON Now the clients can access to Internet through IDL 4802 Admin ONY Service profiel 1 Spectrum Profile 1 TCA profile 1 Al Oo gt Service Profile range from 1 to 120 e Spectrum Profile range from 1 to 120 The TCA Profile range from 1 to 64 e KA Cc EJ a 3 O O e e SERVICE PROFILE SPECTRUM PROFILE TCA PROFILE 17 _ Step 6 Save the running configuration to Flash Remember to save vour running configuration to the flash otherwise the settings will be lost if vou power off IDL 4802 Go to Maintenance gt Database setting screen select the D Save Running Config to Flash System Config There are two partitions on f
6. anty for this product Overview Front Panel The front panels are shown below 48 Port DSLAM Switch PLANET IDL 4802 DSL Stat 4 3 5 7 9 14 19 45 17 10 21 23 25 27 29 31 33 35 37 39 41 43 4547 ik QOQQQQOQOOOQQOQOOQQOQOQOQQOQOQOOQOOQQ stadiy 2 O00000000000000000000000 IDL 4802 48 Port DSLAM Switch PLANET IDL 4802 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 eli 1 oooooooooooooooooooooooo 20D00000000000000000000000 IDL 4802 48 Interface Definition Interface Description POWER Power On Off switch 48V DC Power plug in IDL 4802 48 RJ 45 port for connection with the RJ 45 port on the front panel FAN of fan card to provide power to the fan HK RJ 50 port for housekeeping inputs and one alarm contact output RS 232 port for system configuration and maintenance 9600 Console 8 N 1 A hidden reset button for hardware resetting IERI Cut Off Ethernet Port connected to LAN for providing svstem out band MGMT Telnet control interface such as svstem monitor control or software upgrade LED Definition LED Color Description Uplink Port connect with 100 1000Mbps On Orange Ethernet link Off Uplink Port connect with 10Mbps Ethernet link Active Green Off Inactive Uplink Port Transmit receive data Normal Operation Self test fail Green Normal Operation To indicate the system alarm status On ADSL Port is activated a
7. can create a voltage potential between the earth grounds of two or more buildings If products installed in separate building are interconnected the voltage potential can cause a hazardous condition Consult a qualified electrical consultant to determine whether or not this phenomenon exists and if necessary implement corrective action before interconnecting the products If the equipment is to be used with telecommunications circuit take the following precautions Never install telephone wiring during a lightning storm Never install telephone jacks in wet location unless the jack is specially designed for wet location Never touch un insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Caution when installing or modifying telephone lines other than a cordless tele phone during an electrical storm There is a remote risk of electric shock from lightning Do not use a telephone or other equipment connected to telephone lines to report a gas leak in the vicinity of the leak Hardware Installation The PLANET IDL 4802 is a 1 5U high box tvpe IP DSLAM with rack mountable enclosure It can be installed in a standard 19 inch rack by using the mounting brackets provided Mount the shelf on the rack using the large screws provided STANDARD FRONT MOUNT MOUNTING MOUNTING BRACKET i i BRACKET FRONT The procedures to connect and wire the svste
8. equired 6 Console Port Connection 48 Port DSLAM Switch PLANET IDL 4802 DSL Stat 4 3 5 7 91443151719 21 23 25 27 29 31 33 35 37 39 41 43 4547 oti oooooooooooooooooooooooo 2 O00000000000000000000000 PHONE 2 The Console interface on the front panel is the main control interface of the IDL 4802 To connect the host PC to the console port a RJ45 male connector to RS232 DB9 female connector cable is required The RJ45 connector of the cable is connected to the COM port of the DSLAM the DB9 connector of the cable is connected to the PC COM port 7 Housekeeping Connection 4 3 5 7 9 11131517 19 21 23 25 27 29 31 33 35 37 39 41 43 4547 Li oooooooooooooooooooooooo 20D00000000000000000000000 PHONE 2 The IDL 4802 equips with a RJ 50 port HK on the front panel to provide four housekeeping inputs and one alarm contact output Generally housekeeping contacts can connect to environment sensor controlled switch to indicate the operation environment condition 11 Ee The HK circuit contains a photo coupler powered by the IDL 4802 to detect the open or close status of the loop between HK_IN and HK_COM users don t need to feed 3 3v power into the circuit As to the alarm output there is a relay between ALMOUT and ALMCOM to control the status of the loop to be OPEN or CLOSE to the alarm equipment close between ALMOUT and ALMCOM for alarm open if no alarm HK Port RJ 50 pin assignment ALMOUT H
9. lash select your Partition which you want to save and click Write Running The configuration will save to the Flash Default Partition is Partition1 Further information For further detail configurations and information can be found in the user s manual CD If vou have anv other questions please contact the local dealer where vou purchasing this product 19iF This page is intentionally left blank
10. m are as follows 1 Power and Ground Connections Power Connections With IDL 4802 connect the AC power cord to the AC supply socket on the rear panel as below figure and plug the cord into the external power source The voltage must be 100 to 240V AC With IDL 4802 48 the DC power interface is a 4 pin terminal block with polarity signs on the front panel as below figure It can be powered from two 48V DC power supply The DC power connector is a 4P terminal block 2P is for accommodating one DC power input and other 2P is for accommodating another DC power input The DC power should be connected to a well fused power supply After completing chassis installation please apply power to the fused power distribution panel feeding the chassis When using a DC voltmeter please check for proper voltage 60V 36V DC and make sure that the polarity is correct 7 Ee 4 3 5 7 9 11131517 19 21 23 25 27 29 31 33 35 37 39 41 43 4547 Li oooooooooooooooooooooooo 2 O00000000000000000000000 Ground Connections E In Central Office There should be a CO GND that is adequately grounded If the measured resistance from the grounding screw on the rear panel of the DSLAM refer to below figure to CO GND is less than 5 Ohm then it can be assumed that the system is well grounded If the measured resistance is larger than 5 Ohm it is recommended to connect the grounding screw to CO GND using 14 or 12 AWG wire gauge conductor
11. nd linked DSL status Green Off ADSL Port is Disabled ADSL Port is activated but not linked Rear Panel The rear panels are shown below Ik IDL 4802 ik r i i IDL 4802 48 Port Definition Port Description _ _ AC Power cord plug in 100 240VAC is allowed AEN IDL 4802 Safetv Instruction The following is the safetv instructions for IP DSLAM before installing gt gt The maximum operating temperature of the IP DSLAM is 65 C Care must be taken to allow sufficient air circulation or space between units when the IP DSLAM is installed inside a closed rack assembly and racks should safely support the combined weight of all IP DSLAM gt gt The connections and equipment that supply power to the IP DSLAM should be capable of operating safely with the maximum power requirements of the IP DSLAM In the event of a power overload the supply circuits and supply wiring should not become hazardous gt gt The AC power cord must plug into the right supply voltage Make sure that the supplied AC voltage is correct and stable If the input AC voltage is over 10 lower than the standard may cause the IP DSLAM to malfunction gt gt Generally when installed after the final configuration the product must comply with the applicable safety standards and regulatory requirements of the country in which it is installed If necessary consult for technical support gt gt A rare condition
12. rotocol Base VLAN Disabled V au Delete Port at 12 vilpve 1 v Query Select Port VPI VCI Rx Traffic Tx Traffic ENCAP i Co 4 fi f gt O 2 m yo SE e O 3 ti O 4 O 5 O 6 TO z le 8 O g 10 re 11 O 12 ATM TRAFFIC PARAMETER Vou can see the Port has been created VPI O iya 35 Traffic Default UnShaped Y Tx Default UnShaped Encap LLC Protocol Base VLAN Disabled v ALL Cc Create Modify Port 01 12 MIZ v cuer l i Protocol Select Port VPI VCI Rx Traffic Tx Traffic ENCAP Base VLAN Wo 1 D 35 Default Default LLC Disabled ow WN o 0 0 o oooooo 15IF Step 4 Enable the ADSL Port Service Go to System 9 ADSL Port Service setting screen select the ADSL port and Admin is ON Click Modify to make this Port is ON System gt gt ADSL Port Service ONY Bervice Profile 1 Spectrum Profile 1 TCA Profi 1 All e Service Profile range from 1 to 120 The Spectrum Profile range from 1 to 120 The TCA Profile range from 1 to 64 Port 01712 ta ME SAMA aan an Gn Sa we 2 OFF OFF 1 1 1 5 OF OFF a E 4 oO 4 OFF OFF 1 4 I Lo 5 OFF OFF 1 1 3 MELA a g E a O 7 OFF OFF 1 4 FET Ber a OFF OFF i 4 All a a a ar z Te We 10 OFF OFF 1 1 1 O n OFF OFF H 4 A d You can see the Admin status became to ON System gt gt ADSL Port
13. tion Frame The MDF Patch panel is optional of standard package 9 e Please plug in the RJ 21 cable with connector tenon as below figures Co LI OQ 48 Port DSLAM Switch PLANET A l xii _ _ IDL 4802 dana y Pasina E a E Le ail a A 8 Ply A id nn A Aa 48 Port DSLAM Switch Q PLANET IDL 4802 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 4547 Link 000000000000000000000000 i Standby 2000000000000000000000000 4 The system provides two types of trunk interfaces two ports for each type There are electrical RJ 45 and optical SFP interfaces When both electrical and optical ports are connected system will automatically select the interface according to the priority setting Fiber first or Copper first SFP Mini GBIC Prepare a proper SFP module and install it into the optical trunk port Then you can connect fiber optics cabling that uses LC connectors or SC connectors with the use of an optional SC to LC adapter to the fiber optics connector on the trunk port 5 Management Port Connection 48 Port DSLAM Switch Q PLANET IDL 4802 DSL Stat 4 3 5 7 91443145171921 23 25 27 29 31 33 35 37 39 41 43 4547 oti oooooooooooooooooooooooo 20000000000000000000000004 PHONE 2 The IDL 4802 provides one RJ45 MGMT on the front panel for Ethernet interface connection To connect the Ethernet interface to PC directly an Ethernet crossover cable is r
Download Pdf Manuals
Related Search
IDL 4802 QuickGuide