Chauvet Legend 300E Spot Manual
Contents
1. Y 4 Operation Control Panel Description LCD Display 4 Control Options Programming Navigation Buttons Operation Button Function MENU Exits from the current menu or function Enables the currently displayed menu or sets the currently selected HEES value in to the current function lt UP gt Navigates upwards through the menu list and increases the numeric value when in a function DOWN Navigates downwards through the menu list and decreases the numeric value when in a function The Legend 300E Spot features a backlit liquid crystal display LCD that provides plenty of information regarding the fixture s settings and status In addition the LCD is reversible This allows reading it normally whether the fixture is on the floor or hanging from a truss Dmx Address 001 A Md 2 25Ch Temp 30 C legend Upon power up the LCD will show the Legend logo and the fixture identification as shown on the left figure above After completing the power up tests the LCD will show the DMX address the DMX mode and the temperature along with the warning sign if the tests have detected an error Press lt ENTER gt to read the corresponding error message see Error Messages in the Technical Information section Press lt ENTER gt while looking at the error messages to clear them You can set the Legend 300E Spot start address in the 001 512 DMX range This allows for the control of up to 17 fixture2. b Accept the selected option Highlight Bl o Gobo Change the current setting will show To black out the output when the gobo wheel changes press ENTER a pop up window will open a Select YES to black out the output during a gobo change or NO to keep the output on to see the gobo changing b Accept the selected option Legend 300E Spot User Manual Rev 01g 13 Operation CHAUVET Lamp Settings From the Main Menu highlight Fixture Settings and press ENTER D The lamp will not ignite if the ambient temperature is 104 F 45 C or higher Lamp On Off 1 Highlight On Off the current setting will show 2 Toturn the lamp on or off press ENTER a pop up window will open a Select ON to turn the lamp on or OFF to turn the lamp off b Accept the selected option Lamp Status During 1 Highlight State Power On the current setting will show Power On 2 Tochange the lamp status during power on press ENTER a pop up window will open a Select ON to turn on the fixture and the lamp simultaneously or OFF to turn on the fixture without turning on the lamp b Accept the selected option Remote Turn Off 1 Highlight Off Via DMX the current setting will show 2 Toenable disable remote turn off press ENTER a pop up window will open a Select YES to enable fixture turn off from either a DMX controller or its power switch or NO to turn the fixture off only from its power switch b Acce
3. b Accept the new value Ch Operation Display Settings From the Main Menu highlight Display Settings and press lt ENTER gt a new menu with the DMX functions will open Overturn Display 1 2 LCD Backlight Off 1 Backlight Brightness 1 Temperature Unit 1 Highlight Display Inverse the current setting will show To overturn the display press lt ENTER gt a pop up window will open a Select YES to turn the LCD around fixture hanging from a truss or NO to keep the normal LCD view fixture standing on a surface b Accept the selected option Highlight Backlight Auto Off the current setting will show To configure the LCD backlight press lt ENTER gt a Select YES to automatically turn the LCD backlight off or NO to keep the LCD backlight always on b Accept the selected option Highlight Backlight Intensity the current setting will show To set the backlight brightness press ENTER a pop up window will open a Select the backlight brightness 1 10 being 1 the darkest and 10 the brightest settings b Accept the new value Highlight Temperature Unit the current setting will show To select the temperature unit press ENTER a pop up window will open a Select C to show the temperature in the Celsius scale or F to show the temperature in the Fahrenheit scale b Accept the selected option Fixture Tests From the Main Menu highlight Display Settings and
4. Edition Notes Edition Notes Trademarks Copyright Notice Manual Usage Document Printing Intended Audience Disclaimer CHAUVET Publications Hot Line Document Revision Product at a Glance CHAUVET The Legend 300E Spot User Manual Rev 01g covers the description safety precautions installation programming operation and maintenance of the Legend 300E Spot CHAUVET released this edition of the Legend 300E Spot User Manual Rev 01g in December 2010 CHAUVETO is a registered trademark of CHAUVET amp Sons Inc d b a CHAUVET or Chauvet The CHAUVET logo in its entirety including the Chauvet name and the dotted triangle and all other trademarks on this manual pertaining to services products or marketing statements example It s Green Thinking are owned or licensed by CHAUVET Any other product names logos brands company names and other trademarks featured or referred to within this document are the property of their respective trademark holders CHAUVET owns the content of this user manual in its entirety including but not limited to pictures logos trademarks and resources Copyright 2010 CHAUVET All rights reserved Electronically published by CHAUVET in the United States of America CHAUVET authorizes its customers to download and print this manual for professional information purposes only CHAUVET expressly prohibits the usage copy storage distribution modification
5. Gobo 2 reset Shutter reset Focus zoom prism frost reset Iris flatb reset Heset all No function Lamp off Enable Flatb Disable Flatb Legend 300E Spot User Manual Rev 01g Y 5 Technical Information A N N D Legend 300E Spot User Manual Rev 01g General Maintenance A Photometrics Zoom 35 Zoom 16 LL LL tt EN LL LL LLL LL LO 1 Ll oll ol lil LI O 0 5 10 Technical Information To maintain optimum performance and minimize wear the user should clean the light fixtures frequently Usage and environment are contributing factors in determining the cleaning frequency As a rule the user should clean the fixtures at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced light source life and increased mechanical wear CHAUVET recommends cleaning the fixture s external optics with a soft cloth using normal glass cleaning fluid To clean a fixture follow the recommendations below Unplug the fixture from power Wait until the fixture is cold Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external vents and reachable internal components Clean all external optics and glass surfaces with a mild solution of glass cleaner or isopropyl alcohol and a soft lint free cotton cloth or a lens cleaning tissue Apply the solution directly to the cloth or tissue and drag any di
6. A brief description of the problem Be sure to pack the fixture properly Any shipping damage resulting from inadequate packaging will be the customer s responsibility As a suggestion proper UPS packing or double boxing is always a safe method to use CHAUVET reserves the right to use its own discretion to repair or replace returned product s Claims The carrier is responsible for any damage incurred during shipping Therefore if the received merchandise appears to have damages caused during shipping the customer must submit the damage report and any related claims with the carrier not CHAUVET The customer must submit the report upon reception of the damaged merchandise Failure to do so in a timely manner may invalidate the customer s claim with the carrier For other issues such as missing components or parts damage not related to shipping or concealed damage the customer must make claims to CHAUVET within seven 7 days of receiving the merchandise Contact Us World Headquarters General Information CHAUVET 5200 NW 108th Avenue Sunrise FL 33351 Voice 954 929 1115 Fax 954 929 5560 Toll free 800 762 1084 Technical Support Voice 954 929 1115 Press 4 Fax 954 756 8015 World Wide Web www chauvetlighting com 28 Legend 300E Spot User Manual Rev 01g Technical Information CHAVET Technical Specifications Weight amp dimensions DSTO UA EE 14 5 in 370 mm e un EE 17 9 in 456 mm A 6 O AA A
7. Macro 11 096 U 103 Macro 12 104U 111 Macro 13 112U 119 Macro 14 120U 127 Macro 15 128 U 135 Macro 16 136 143 Macro 17 144U 151 Macro 18 152 U 159 Macro 19 160 U 167 Macro 20 169U 175 Macro 21 176U 183 Macro 22 184U 191 Macro 23 192U 199 Macro 24 200U 207 Macro 25 208 U 215 Macro 26 216 U 223 Macro 27 224 231 Macro 28 232 239 Macro 29 240 247 Macro 30 248 U 255 Macro 31 21 25 Pan Tilt Macro Continues on the next page Legend 300E Spot User Manual Rev 01g 23 Operation 24 Continued from the previous page Mode 2 Channel Function Cont 26 27 28 29 Preset Color Color Macro Function Value 000 U 070 U 080 U 090 U 100 U 1100 120 U 130 U 140 U 150 0 160 U 170 U 180 U 190 U 200 210 230 240 250 U P T Macro Speed 000 U 255 069 079 089 099 109 119 129 139 149 159 169 179 189 199 209 229 239 249 255 Percent Setting Fast Slow White Color 1 Color 2 Color 3 Color 4 Color 5 Color 6 Color 7 Color 8 Color 9 Color 10 Color 11 Open Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro 6 Macro 7 Macro 8 Macro 9 Macro 10 Macro 11 Macro 12 No function Enable BO during Pan or Tilt Disable BO during Pan or Tilt Enable BO during color change Disable BO during color change Enable BO during gobo change Disable BO during gobo change Lamp on Pan Tilt reset Color CMY reset Gobo 1
8. and press ENTER a new menu with the fixture information will open 1 Highlight Fixture Use Time the accumulated fixture s operation time will show You cannot modify or reset the fixture operation timer 1 Highlight Lamp On Time the accumulated lamp s operation time will show 2 Toreset the lamp operation timer press ENTER a pop up window will open a Select Reset Time to reset the timer or Exit to exit without resetting b Accept the selected option 1 Highlight Firmware Version 2 Tosee the firmware versions installed press ENTER a sub menu will open a The display will show the current firmware version for each of the four CPU boards A through D in the fixture b Return to the previous menu From the Main Menu highlight Reset and press ENTER a new menu with the resettable attributes will open You can leave this sub menu at any time by pressing lt MENU gt 1 Highlight Pan Tilt and press ENTER a pop up window will open a Select YES to reset the pan and tilt movements to their home positions b Accept the selected option 1 Highlight Color CMY and press ENTER a pop up window will open a Select YES to reset the color wheel and the CMY filters to their home positions b Accept the selected option 1 Highlight Gobo and press ENTER a pop up window will open a Select YES to reset the gobo wheel to its home position b Accept the selected option 1 Highlight Shut
9. press ENTER a new menu with the test functions will open Automatic Fixture Test 1 2 Highlight Auto Test To start the built in test sequence press ENTER a The fixture will start the test sequence pan tilt color CMY gobo selection gobo rotation shutter dimmer prism activation prism rotation frost zoom and lamp on off b You can stop the test by pressing MENU c Return to the previous menu La The automatic fixture test runs only once after activation Manual Fixture Test 1 Highlight Manual Test and press lt ENTER gt a sub menu will open Highlight the desired attribute the current setting will show To change the value of the selected attribute press ENTER a pop up window will open a Set the attribute value 000 255 the fixture will assume the new attribute value as you change it as if you were working with a DMX controller b Accept the new value Repeat steps 2 and 3 for the other attributes When done with the test exit to the previous menu the values of all tested channels will go back to zero Legend 300E Spot User Manual Rev 01g 15 Operation Fixture Information Fixture Operation Timer 4 Lamp Operation Timer Firmware Version Reset Functions 4 Pan Tilt Reset Color CMY Reset Gobo Reset Shutter Dimmer Reset Focus Zoom Prism Frost Reset Iris Flatb Reset All 16 CHAUVET From the Main Menu highlight Fixture Information
10. protected circuit Never connect this product to a dimmer pack Make sure the fixture s power cable is not crimped or damaged Never disconnect this product by pulling or tugging on the power cable Operation Do not operate this fixture if you see damage on the housing lenses ultraviolet filter or cables have the damaged parts replaced by an authorized technician at once Do not aim this fixture toward any surface closer than 16 feet 5 m Otherwise you may damage or overheat the illuminated surface Do not cover the ventilation slots when the fixture is operating to avoid internal overheating Do not aim this fixture toward the Sun Otherwise the lenses could concentrate the solar energy and cause internal overheating The maximum ambient temperature Ta is 104 F 40 C Do not operate this product at a higher temperature In case of a serious operating problem stop using this product immediately In the unlikely event that your Legend 300E Spot may require service please contact CHAUVET Technical Support 2 Legend 300E Spot User Manual Rev 01g Introduction Ch 2 Introduction Product The Legend 300E Spot is a compact electronic moving yoke spot fixture equipped with i a 300 watt HID lamp It includes a color wheel with eight slots plus white It also comes Description with two gobo wheels one with seven rotating slot n lock gobos plus open and the other with eight fixed gobos plus open It also includ
11. 50 U 069 079 089 099 109 119 129 139 149 159 169 179 189 199 209 229 239 249 255 Function Legend 300E Spot User Manual Rev 01g Percent Setting Open Gobo 8 Gobo 9 Gobo 10 Gobo 1 1 Gobo 12 Gobo 13 Gobo 14 Gobo 15 Gobo 8 Shaking Gobo 9 Shaking Gobo 10 Shaking Gobo 11 Shaking Gobo 12 Shaking Gobo 13 Shaking Gobo 14 Shaking Gobo 15 Shaking Fast Slow CW rotation Stop Slow Fast CCW rotation Near Far 0 100 Normal Prism effect Index Fast Slow CW rotation Stop Slow Fast CCW rotation 0 100 0 100 No function Enable BO during Pan or Tilt Disable BO during Pan or Tilt Enable BO during color change Disable BO during color change Enable BO during gobo change Disable BO during gobo change Lamp on Pan Tilt reset Color CMY reset Gobo 1 Gobo 2 reset Shutter reset Focus zoom prism frost reset Iris flatb reset Reset all No function Lamp off Enable flatb Disable flatb 91 Operation CHAUVET Mode 2 Channel Function Value Percent Setting 1 zl OO o0 hN o 10 11 12 13 14 15 16 22 Pan 0000 255 0 540 Pan Eine 000 255 0 100 000 0 255 0 270 000 255 0 100 Fast Slow Dimmer 000 255 0 100 Dimmer Fine 000 U 255 0 100 Black out Open Slow Fast Slow open fast close Fast open slow close Slow open slow close Random strobe Open White Red Orange 3 200 K 5 600 K Pin
12. AA AAA A 20 MOOG EE 20 leie 22 5 Technical Information AA nia 25 General MAIC fS ge EE 25 Legend 300E Spot User Manual Rev 01g a Table of Contents POIS ateo 25 ENON MOSSA JOS iii mt 26 TH OUDISSIOOL IAG EE Te EE 27 FAO TUIITS OCC OUI AAA 28 E e EE 28 Seded erases aa ena ea ae oe acta O ET atta Cane 28 Technical Specie 6 EE 29 b Legend 300E Spot User Manual Rev 01g Ch 1 Before You Begin What is Before You Begin One Legend 300E Spot Two omega clamps Included Three additional gobos One Warranty Card One Quick Reference Guide Unpacking Immediately upon receiving this product carefully unpack it and check the container in i which you received it Make sure that you have received all the parts indicated above Instructions and that they are all in good condition If the material inside the container this product and any other accessory included with it appears damaged from shipping or if the container shows signs of mishandling notify the shipper immediately In addition retain the container and all the packing material for inspection See the Claims section in the Technical Information chapter Typographic Conventions COLORado UM Icon Meaning Convention 1 512 50 60 10 Claims lt SET gt Settings MENU gt Settings 1 10 Yes No ON Icon A D 4 Meaning A range of values in the text A set of mutually exclus
13. NAN ATA AA 23 7 in 601 mm o haaa ab uh Dt NING ue dat RESENS MURAG na pio 47 5 Ibs 21 55 kg Power AUTO TAO IM ma Ana RETO 100 240 V 50 60 Hz Operating currenb 120 V OO TAZ eadera aee eulos aoa ae auf Sese esee hl el Mca lla Ea 4 12 A Operating curent 290 N80 KEE 3 1A PUSH CUENTO 120060 rA 3 1A Inr shC rrent 250 Ve 50 m EE 1 6A Power consumpton 120 Yo60 e KEE 477W Power consumpion 230 V00 KE 468 W Power factor 120 V60 un EE 0 99 POWER taciones aaa Nabangga a na aaa aaah a E OB POLE nG GLOG GNG nob mGa Ha 0 95 HUS ESS ER o agent fin Nan EE Glass 20 mm T 10 A 250 V external Light source PA AA AA AA AA 300 W HID lamp Approved AMP ana e E AT ANAN Philips MSR Gold 300 2 8 400 K 750 hrs SOCK EL said MiniFastFit Head Motion Range ET 540 eer EE 270 Thermal Maximum ambient temperature nennen enne ar klan inni nennen sess sans sana aiias 104 F 40 C Maximum surface temperature esses eene nnne nennen nnne nennen nenne nnns 135 F 57 C Photo Optic Iaminance atom e ee RE 12 200 lux Iaminange ats N1 35 ZOO AAA AAA AAA 2 800 lux Gobo Wheel 1 A ici T D T rV 26 83 mm MAS fe WEE den 23 29 mm STING age 4 32 mm ENT NEE glass Gobo Wheel 2 Otter lege 31 42 mm Maga alameda iii tada 23 04 mm TACOS ss LA AAA EA EA RA ac cel na el AA AAA At 0 80 mm NG NR TO TERR steel Control amp Programming BU lockin
14. Summary Mode 1 DMX Channel O O J O OI A QQ N NINE m m m m m m m m m j El OO 1 OI NI OO oa AI WO NM Function Mode 2 Pan Pan Fine Tilt Tilt Fine Pan Tilt Speed Dimmer Shutter Color Cyan Magenta Yellow Gobo 1 R Gobo 1 Gobo 2 Focus Zoom Prism R Prism Iris Frost Function DMX Channel O D NI OJAI AI OJN gt NINININI AN A RN RN NY NI a a a sch ajaj m m m a OI Our 1 oO a RP NO 2 1 0 0 OINI OO AO P WO ND CHAUVET Function Pan Pan Fine Tilt Tilt Fine Pan Tilt Speed Dimmer Dimmer Fine Shutter Color Cyan Magenta Yellow CMY Speed Gobo 1 R Gobo 1 R Gobo 1 Fine Gobo 2 Focus Zoom Prism R Prism R Prism Fine Iris Frost Pan Tilt Macro P T Macro Speed Preset Color Color Macro Function Legend 300E Spot User Manual Rev 01g Introduction FEI Og A Ce GI P XS IG Rear Panel Power On Off Power Cord Legend 300E Spot User Manual Rev 01g 5 Setup 3 Setup AC Power A D AC Plug A Fuse Replacement DMX Linking DMX Modes CHAUVET The Legend 300E Spot has an auto ranging power supply that can work with an input voltage range of 100 240 VAC 50 60 Hz Make sure that you are connecting this product to the proper voltage as per the specifications in this guide the product s user manual or on the product s sticker Always connect t
15. a pop up window will open a Select Reset Time to reset the timer or Exit to exit without resetting it b Accept the selected option It is a good idea to use the Fixture Maintenance Time as a reminder to change the lamp 1 Highlight Factory Setting and press ENTER a pop up window will open a Select YES to default the fixture to factory settings or NO to exit without resetting b Accept the selected option and wait for the fixture to reset c Return to the previous menu The Offset Mode provides fine adjustments for the home position of all the moving parts in the optical path as well as the pan and tilt movements This way when in their home position the moving parts do not show any border or reduce the light output 1 Press MENU to enter the regular Menu Mode 2 Press ENTER for more than three seconds to enter the Offset Mode the Offset Mode menu will show 1 Select Pan and press ENTER a pop up window will open a Select the new value 128 127 b Accept the new value 1 Select Tilt and press ENTER a pop up window will open a Select the new value 128 127 b Accept the new value 1 Select Shutter and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value 1 Select Dimmer and press lt ENTER gt a pop up window will open a Select the new value 0 255 b Accept the new value 1 Select Color and press lt ENTER gt a pop u
16. ad main controller State Power On parameter set to NO Lamp temperature problems Lamp problems Dimmer not at full output Lamp still cold CTC or CMY filter interfering Defective or old lamp Misaligned lamp Defective lamp wires or socket Defective ballast Defective or old lamp Temperature problems Defective lamp wires or socket Defective ballast Excessive circuit load Short circuit along the power wires Wrong DMX addressing Damaged DMX cables Wrong polarity on the controller Loose DMX cables Faulty DMX interface Faulty Display Main board Non DMX cables Bouncing signals Long cable low level signal Too many fixtures Interference from AC wires Legend 300E Spot User Manual Rev 01g Technical Information Action s Repair outlet problem or use another outlet Replace blown fuse with same type and rating fuse Repair or replace power cord plug Heplace power switch Replace power supply Replace main controller Change parameter to YES Check error messages and follow instructions Check error messages and follow instructions Adjust dimmer value Wait for lamp to come up with full output temperature Set color wheel or filter to home position Replace lamp Realign lamp Repair change wiring or socket Replace ballast Replace lamp Check error messages and follow instructions Repair change wiring or socket Replace ballast Check total load placed on the electrical circuit Check for a shor
17. alues CHAVET Mode 1 Channel Function Value Percent Setting 1 01 amp G ND CO o 10 11 12 13 20 Pan 0000 255 0 540 Pan Fine 000 255 0 100 000 255 0 270 Tilt Fine 000 U 255 0 100 Pan Tilt Speed 000 U 255 Fast Slow Dimmer 000 U_ 255 0 100 Black out Open Slow Fast Slow open Fast close Fast open Slow close Slow open Slow close Random strobe Open White Color Fast Slow CW rotation Stop Slow Fast CCW rotation 000 U 255 0 100 000 U 255 0 100 000 255 0 100 Open Gobo 1 Gobo 2 Gobo 3 Gobo 5 Shaking Gobo 6 Shaking Gobo 7 Shaking Fast Slow CW rotation Stop Slow Fast CCW rotation 000 U 127 Index R Gobo 1 128 U 189 Fast Slow CW rotation 190 U 193 Stop 194 U 255 Slow Fast CCW rotation Red Orange 3 200 K 5 600 K Pink Green Dark Blue Color Mix Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 1 Shaking Gobo 2 Shaking Gobo 3 Shaking Gobo 4 Shaking Continues on the next page Legend 300E Spot User Manual Rev 01g CHAUVET Mode 1 Channel Function Cont 15 16 17 18 19 20 21 Operation Continued from the previous page Value Focus 0000 255 Zoom 000U 255 EE 009 U 255 0000 127 1280 189 190 193 194 U 255 ris 0000 255 Frost 000U 255 000 070 080 090 100 110 120 130 U 140 150 U 160 U 170 180 190 200 210 0 230 U 240 2
18. an to avoid the risk of lamp explosion Setup 10 Mounting Orientation Rigging Procedure Product Mounting Diagram CHAUVET Before mounting this fixture read and follow the safety recommendations indicated in the Safety Notes page 2 of this manual Always mount this fixture in any safe position while making sure that there is adequate room around it for ventilation Make sure to mount this fixture away from any flammable material as indicated in the Safety Notes page 2 of this manual CHAUVET recommends following the general guidelines below when mounting the Legend 300E Spot When selecting an installation location consider ease of access to the fixture for operation programming adjustments and routine maintenance Never mount the fixture in places where rain high humidity extreme temperature changes or restricted ventilation may affect it If hanging this fixture make sure that the location where you are mounting the fixture can support its weight Please see the Technical Specifications section of this manual for the weight requirement of this fixture The Legend 300E Spot comes with an already installed mounting bracket to which you will be able to attach the two included omega clamps Be aware that you will have to use two mounting points per fixture In addition you will have to use a safety cable not included to link the fixture to the structure Legend 300E Spot User Manual Rev 01g
19. es remote focus and a rotating 3 facet prism Features 21 or 29 channel compact fully electronic 300 watt moving yoke spot Pan 540 Tilt 270 Color wheel 7 colors white Split linear colors Color wheel spins at variable speed Gobo wheel 1 Indexed rotating gobo wheel with gobo shake 7 metal slot n lock gobos open Gobo wheel spins at variable speed 16 bit gobo rotation Gobo wheel 2 Indexed gobo wheel 8 metal gobos open Gobo wheel spins at variable speed Static frost CTC filters 5 600 K and 3 200 K CMY color mixing system with vector speed adjustments 3 facet rotating prism Variable shutter Variable iris Variable focus Variable 16 bit dimming 0 100 Linear zoom 16 35 Individual reset of pan tilt color gobo shutter prism focus Move in black for pan tilt color gobo Remote fixture reset lamp on off and vector control speed adjustments Built in movement macros with range adjustments Built in color macros Battery powered display Additional Features 3 pin and 5 pin DMX connections Three additional free gobos User configurable lamp ignition delay User configurable maintenance reminder Electronic ballast with power factor correction Electronic power supply Automatic pan amp tilt correction Pan amp tilt locks Lamp amp fixture use timers Power saver mode Options W DMX wireless DMX receiver W DMX wireless DMX transmitter Legend 300E Spot User Manual Rev 01g 3 Introduction DMX Channel
20. failed going to home position after power up or fixture reset Indicated moving part failed going to home position after power up or fixture reset Check lamp Check lamp socket and wiring Check ballast and igniter Check sensor wiring Check sensor integrity Check control board Check fans Check fan wiring Clean vents Check fans Check fan wiring Clean vents Proceed with maintenance and reset timer Change lamp Change main board Check sensors wiring and position Check stepper motor belt and driver board Check control boards Check moving head s free movement Check sensors wiring and position Check stepper motor belt and driver board Check the corresponding control board Check main control board Check part s free movement and integrity Check sensors wiring and position Check stepper motor belt and driver board Check the corresponding control board Check main control board Legend 300E Spot User Manual Rev 01g Ch Troubleshooting Guide Symptom Fixture does not power up Fixture powers up but lamp does not ignite Lamp ignited but has low intensity color temperature Lamp flickers or turns off by itself Circuit breaker fuse keeps tripping blowing Fixture does not respond to DMX when nearby fixtures on the same universe do DMX signal problems see Appendix gt DMX Primer D Cause s No power on outlet Blown fuse Bad power cord plug Bad power switch Bad power supply B
21. g 3 and 5 pin XLR male socket Bises ERR locking 3 and 5 pin XLR female socket Data DiN CORK UFO cistitis pin 1 shield pin 2 pin 3 A hn kA KN MUN Ga DMX 512 USITT BMX Ga Fal ECC ET 21 and 29 Ordering Information Legend Eeer di LEGEND300SPOT Two Legend 300E Spot units in a single road case LEGEND300SPOT X2 Warranty Information Waah Quran in up cua ropa teo 2 year limited warranty Legend 300E Spot User Manual Rev 01g 29 CHAUVET 5200 NW 108th Ave Sunrise FL 33351 U S A 800 762 1084 954 929 1115 FAX 954 929 5560 www chauvetlighting com Legend 300E Spot User Manual Rev 01g December 2010
22. he Legend 300E Spot to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire To determine the power requirements for the Legend 300E Spot see the label affixed to the side of the fixture Alternatively you may refer to the corresponding specifications chart in the Technical Information chapter of this manual The listed current rating indicates the maximum current draw during normal operation Please refer to the Sizing the Circuit Breakers section in the Appendix chapter of this manual Never connect the Legend 300E Spot to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch The Legend 300E Spot comes with a bare ended power input cord The fixture side of this power cord enters the fixture through a strain reliever rubber boot and it cannot be disconnected from the fixture Use the table below to wire the plug to the power cord Connection Wire US Wire Europe Screw Color AC Live Yellow or Brass AC Neutral Silver AC Ground Green Yellow Green Yellow Green Make sure to disconnect the fixture s power cord before replacing a blown fuse and always replace it with a fuse of the same type and rating 1 With a Philips screwdriver unscrew the fuse holder out of its housing and remove the blown fuse from its holder 2 Replace the blown fuse with a fuse of the exact same type and rating 3 Reverse step 1 and rec
23. ive values in the text A DIP switch to be configured A new term or a section or chapter of this document The name of another publication or manual A button on the fixture s control panel A fixture function or a menu option A sequence of menu options A range of menu values from which to choose in a menu A set of two mutually exclusive menu options in a menu A unique value to entered or select in a menu Meaning This icon indicates critical installation configuration or operation information Failure to comply with this information may render the fixture partially or completely inoperative damage third party equipment or cause harm to the user This icon indicates important installation or configuration information Failure to comply with this information may prevent the fixture from functioning correctly This icon indicates useful although non critical information transmission protocol La The term DMX used throughout this document refers to the USITT DMX512 A Legend 300E Spot User Manual Rev 01g CB mm fom num UH s ER mali lt ATOra Y Oi i L e Cy r perore Y ou Begin z B OU LE Safety Notes Please read the following notes carefully because they include important safety information about the installation usage and maintenance of this product It is important to read all these notes before starting to work with this product There are no user serviceable parts inside this product Any reference to i ser
24. k Green Dark Blue Color Mix Fast Slow CW rotation Stop Slow Fast CCW rotation 0 100 000 U 255 0 100 000 255 0 100 Fast Slow Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 1 Shaking Gobo 2 Shaking Gobo 3 Shaking Gobo 4 Shaking Gobo 5 Shaking Gobo 6 Shaking Gobo 7 Shaking Fast Slow CW rotation Stop Slow Fast CCW rotation Index Fast Slow CW rotation Stop Slow Fast CCW rotation R Gobo 1 Fine 000 U 255 0 100 Color R Gobo 1 Continues on the next page Legend 300E Spot User Manual Rev 01g Operation CH Mode 2 Channel Function Value Percent Setting Cont Continued from the previous page Open Gobo 8 Gobo 9 Gobo 10 Gobo 11 Gobo 12 Gobo 13 Gobo 14 Gobo 15 Gobo 8 Shaking Gobo 9 Shaking Gobo 10 Shaking Gobo 11 Shaking Gobo 12 Shaking Gobo 13 Shaking Gobo 14 Shaking Gobo 15 Shaking Fast Slow CW rotation Stop Slow Fast CCW rotation 18 Focus 0000 255 Near Far 19 000 U 255 0 100 20 000 U 008 Normal 009 U 255 Prism effect 000 0 127 Index 128 U 189 Fast Slow CW rotation 190U 193 Stop 194U 255 Slow Fast CCW rotation 22 000 U 255 0 100 23 iris 0000 255 100 0 008 255 Frost 000 U 007 Off 008 015 Macro 1 016 023 Macro 2 024 U 031 Macro 3 032 039 Macro 4 040 U 047 Macro 5 048 U 055 Macro 6 056 U 063 Macro 7 064 U 071 Macro 8 072 U 079 Macro9 080 U 087 Macro 10 088 095
25. nstalled on the Legend 300E Spot fixture Legend 300E Spot User Manual Rev 01g Ch Operation Fixture Settings From the Main Menu highlight Fixture Settings and press lt ENTER gt a new menu with the fixture settings will open Reverse Pan Direction 1 2 Reverse Tilt Direction 1 2 Head Motion Black Out 1 Color Change Black Out 1 Gobo Change Black Out 1 Highlight Pan Inverse the current setting will show To reverse the pan direction press lt ENTER gt a pop up window will open a Select YES to reverse the pan direction or NO to use the normal pan direction b Accept the selected option Highlight Tilt Inverse the current setting will show To reverse the tilt direction press lt ENTER gt a pop up window will open a Select YES to reverse the tilt direction or NO to use the normal tilt direction b Accept the selected option Highlight Bl o P T Moving the current setting will show To black out the output when the head moves press ENTER a pop up window will open a Select YES to black out the output when the head tilts or pans or NO to keep the output on while the head moves b Accept the selected option Highlight Bl o Color Change the current setting will show To black out the output when the color wheel changes press ENTER a pop up window will open a Select YES to black out the output during a color change or NO to keep the output on to see the color changing
26. obo Replacement Diagram Make sure to disconnect the fixture s power cord before replacing a gobo Always replace a gobo with a gobo of the same dimensions When inserting a glass gobo always make sure that the shiny side of the gobo glass base faces the lamp This provides a layer of protection against the high temperature from the lamp Turn the fixture off and disconnect it from the power outlet Open the head cover by loosening the four fastening screws at the sides of the top cover Separate the gobo plate away from the gobo wheel by pushing it toward the front of the moving head direction 1 in the diagram Be careful not to push the gobo out of the gobo plate Extract the gobo plate by pulling it outward direction 2 in the diagram On a flat surface remove the expansion ring that holds the gobo in place and remove the gobo from the gobo plate Insert a new gobo and hold it in place with the expansion ring Slide the tip of the gobo plate under the pressure plate near the center of the gobo wheel Push the gobo plate inwards DO NOT force the gobo plate into the gobo wheel slot If correctly installed the gobo plate should accommodate itself in the gobo wheel slot Legend 300E Spot User Manual Rev 01g Ch Setup Lamp The Legend 300E Spot is equipped with a Philips MSR Gold 300 2 lamp This lamp uses a socket called FastFit which allows for fast and easy lamp changes Follow the Re placement procedure below
27. onnect power You may link the Legend 300E Spot to a DMX controller using a standard DMX serial connection If using other DMX compatible fixtures with the Legend 300E Spot it is possible to control them individually with a single DMX controller If you are not familiar with the DMX standard you may download the DMX Primer document from the CHAUVET Web site The Legend 300E Spot uses the standard DMX data connection for its DMX Modes Mode 1 and Mode 2 You will find information about these DMX modes in the Introduction chapter brief description the Operation Instructions chapter configuration details and the DMX Values section individual channel values Legend 300E Spot User Manual Rev 01g Setup CHAUVET The Legend 300E Spot comes with two gobo wheels Gobo wheel 1 has seven rotating Gobo Wheels gobos while gobo wheel 2 has eight fixed gobos as indicated below The diagram shows the first and last gobo on each wheel as per the DMX Values tables Rotating Gobos Fixed Gobos 26 8 mm 26 8 mm 26 8 mm Extra Gobos 24 mm Color Wheel CTC 3200 K Legend 300E Spot User Manual Rev 01g 7 Setup CHAUVET Gobo The gobos in the Legend 300E Spot s gobo wheel are removable from their gobo plates This operation is quite simple although it requires the technician to be careful and to Replacement follow the recommended procedure A Procedure 1 2 3 4 5 6 7 8 G
28. ontinue below To change the current mode press ENTER a pop up window will open a Select a DMX mode Mode 1 Mode 2 b Accept the selected option Highlight View DMX Value Press MENU to exit or continue below Press ENTER the value for each of the attributes of the current DMX mode will show a Scroll along the list to see the values of all the current attributes b Return to the previous menu The list will show either 17 or 25 attributes depending on the current DMX mode h al 8 Highlight WDMX Setting Press MENU to exit or continue below To see the WDMX settings press ENTER a sub menu will open Press MENU to exit or continue below To activate or deactivate W DMX highlight Active the current setting will show and press lt ENTER gt a pop up window will open a Select YES to activate W DMX or NO to deactivate W DMX b Accept the selected option To enable or disable retransmission highlight Retransmit the current setting will show and press lt ENTER gt a pop up window will open a Select YES to enable retransmission or NO to deactivate retransmission b Accept the selected option To reset the memory highlight Reset Memory and press lt ENTER gt a pop up window will open a Select YES to reset the memory or NO to exit without resetting b Accept the selected option Return to the previous menu The W DMX functionality requires the W DMX transceiver i
29. or printing of this manual or its content for any other purpose without its written consent For better results print this document in color on letter size paper 8 5 x 11 inches double sided If using A4 paper 210 x 297 mm configure your printer to scale the content of this document to A4 paper Any person in charge of installing operating and or maintaining the Legend 300E Spot should read the guide that shipped with it and this manual in their entirety before installing operating or maintaining this product CHAUVET believes that the information contained in this manual is accurate in all respects However CHAUVET assumes no responsibility for any error or omissions in this document CHAUVET reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of CHAUVET to notify any person or company of such revision or changes This does not constitute in any way acommitment by CHAUVET to make such changes CHAUVET may issue a revision of this manual or a new edition of it to incorporate such changes If you have any comments about the accuracy of this document or general suggestions regarding how we can improve it please call us at 800 762 1084 US callers or 1 954 929 1115 international callers You can download the latest versions of all CHAUVET products manuals from www chauvetlighting com The Legend 300E Spot User Manual Rev 01g supersedes all pre
30. p window will open a Select the new value 128 127 b Accept the new value 1 Select Cyan and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value 1 Select Magenta and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value Continues on the next page Legend 300E Spot User Manual Rev 01g 17 Operation 18 Yellow Gobo 1 R Gobo 1 Gobo 2 Iris Prism R Prism Frost Flab Focus Zoom CHAUVET Continued from the previous page Select Yellow and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value Select Gobo 1 and press ENTER a pop up window will open a Select the new value 128 127 b Accept the new value Select R Gobo 7 and press lt ENTER gt a Select the new value 128 127 b Accept the new value Select Gobo 2 and press ENTER a pop up window will open a Select the new value 128 127 b Accept the new value Select Iris and press lt ENTER gt a pop up window will open Select the new value 0 255 and press lt ENTER gt Return to the Offset Mode menu Select Prism and press ENTER a pop up window will open Select the new value 0 255 and press ENTER Return to the Offset Mode menu Select R Prism and press ENTER a pop up window will open a Select the new value 128 127 b Accept the ne
31. pt the selected option Lamp On if DMX Present 1 Highlight On if DMX On the current setting will show 2 Toturn the lamp on when DMX is present press ENTER a pop up window will open a Select YES to turn the lamp on if DMX signal is present or NO to turn the lamp on only from the control panel b Accept the selected option Lamp Off if DMX Absent 1 Highlight Off if DMX Off the current setting will show 2 Toturn the lamp off when DMX is absent press ENTER a pop up window will open a Select YES to turn the lamp off if DMX signal is absent or NO to turn the lamp off only from the control panel b Accept the selected option Fan Speed 1 Highlight Cooling Mode the current setting will show 2 Tochange the fan speed setting press ENTER a pop up window will open a Select AUTO to allow the fixture s controller to set the fan speed or HIGH to set the fan speed to high mode b Accept the new selection Lamp Strike Delay 1 Highlight Ignition Delay the current setting will show 2 Tosetthe lamp strike delay press ENTER a pop up window will open a Select the delay before the lamp strikes after power up in seconds 0 255 b Accept the new value Fixture Shut Off Delay 1 Highlight Low Power Delay the current setting will show 2 Tosetthe lamp shut off delay press ENTER a pop up window will open a Select the delay before the fixture powers off after lamp off in seconds 0 255
32. rt and grime to the outside of the lens Gently polish the external glass surfaces until they are free of haze and lint When cleaning units with a movable mirror you should keep the contact with the mirror surface to a minimum to avoid scratching or damaging it Always dry the external optics and glass surfaces carefully after cleaning them If the fixture has one or more fans refrain from spinning them using compressed illuminance lux 2 800 695 315 12 200 3 070 1 400 359 16 i 15 Distance m 25 Technical Information CHAUVET Error Messages Message Cause s Action s Lamp Startup Fail Temperature Sense Error Lamp too Hot Low Power Lamp Too Hot Power Off Maintenance Fixture The lamp has not started after being struck No communication with temperature sensor Ambient temperature higher than 105 C lamp in low power for safety Ambient temperature higher than 110 C lamp off for safety Fixture Maintenance timer expired Lamp On Over 700 Hour Lamp change is overdue Memory Initial Fail CPU B Error CPU C Error CPU D Error Pan Reset Error Pan Encode Error Tilt Reset Error Tilt Encode Error Shutter Reset Fail Dimmer Reset Fail Color Reset Fail Cyan Reset Fail Magenta Reset Fail Yellow Reset Fail Gobo Reset Fail R Gobo Reset Fail Effect Reset Fail R Effect Reset Fail Frost Reset Fail 26 Memory chip error No communication with auxiliary CPU Moving head
33. s in the 29 channel Mode 2 The Legend 300E Spot works with any compatible DMX controller using standard DMX cables or the optional W DMX receiver Carry out all the programming procedures indicated below from the control panel Refer to the Menu Map page to learn how the menu options relate to each other To enter programming mode press MENU until you see the Main Menu To highlight a menu option or to change a setting press UP or lt DOWN gt To change menu levels as shown in the Menu Map press ENTER or lt MENU gt This is equivalent to moving right and left of the Menu Map respectively To accept the current or new value press lt ENTER gt To return to the previous menu without making changes press MENU To exit programming mode press MENU until you see the Main Menu or do not press any button for 30 seconds Legend 300E Spot User Manual Rev 1g AA Operation 12 DMX Functions DMX Address DMX Mode View DMX Values 4 W DMX Settings CHAUVET From the Main Menu highlight DMX Functions and press ENTER a new menu with the DMX functions will open 1 2 3 Highlight DMX Address the current address will show Press MENU to exit or continue below To change the current address press ENTER a pop up window will open a Change the starting address 001 512 b Accept the new value Highlight DMX Channel Mode the current mode will show Press MENU to exit or c
34. t in the electrical wiring Check DMX mode and starting DMX address Check DMX cables Check polarity switch settings on the controller Check cable connections Replace the Main board Replace the Main board Use only DMX compatible cables Install terminator as suggested Install an optically coupled DMX splitter right after the fixture with the strong signal Install an optically coupled DMX splitter after unit 32 or before Keep DMX cables separated from power cables or fluorescent black lights If you still experience technical problems after trying the above solutions contact CHAUVET Technical Support 27 Technical Information CHAUVET Returns The user must send the merchandise prepaid in the original box and with its original packing and accessories CHAUVET will not issue call tags Procedure Call CHAUVET and request a Return Merchandise Authorization Number RMA before shipping the fixture Be prepared to provide the model number serial number and a brief description of the cause for the return The user must clearly label the package with a Return Merchandise Authorization Number RMA CHAUVET will refuse any product returned without an RMA La DO NOT write the RMA directly on the box Instead write it on a properly affixed label Once you receive the RMA please include the following information on a piece of paper inside the box Your name Your address Your phone number The RMA
35. ter Dimmer and press ENTER a pop up window will open a Select YES to reset the shutter and dimmer to their home positions b Accept the selected option 1 Highlight Focus Zoom Prism Frost and press ENTER a pop up window will open a Select YES to reset the focus the zoom the prism and the frost to their home positions b Accept the selected option 1 Highlight Iris Flatb and press ENTER a pop up window will open a Select YES to reset the iris and flatb to their home positions b Accept the selected option 1 Highlight Al and press ENTER a pop up window will open a Select YES to reset all moving optical parts and the moving head to their home positions b Accept the selected option Legend 300E Spot User Manual Rev 01g Ch Special Functions Fixture Maintenance Timers 4 Fixture Defaulting Offset Mode Entering Offset Mode Pan Tilt Shutter Dimmer Color Cyan Magenta Operation From the Main Menu highlight Special Functions and press ENTER a new menu with the special functions will open 1 Highlight Fixture Maintenance and press ENTER the current maintenance interval and remaining time will show 2 Tochange the maintenance interval timer highlight Interval and press ENTER a pop up window will open a Select the new interval in hours b Accept the new value 3 Toreset the remaining time counter highlight Remain Time and press ENTER
36. to safely change the Legend 300E Spot s lamp Procedure 1 0 N O OOF CO N CO Lamp Replacement Diagram Increasing the Lamp s Life Legend 300E Spot User Manual Rev 01g Turn the fixture off and disconnect it from the power outlet Wait at least 15 minutes for the lamp to cool down Loosen the two screws on the lamp cover marked A in the diagram Lift and rotate the lamp cover as per the diagram to expose the base of the lamp Rotate the ceramic base of the lamp 90 counterclockwise Pull the lamp out by holding it from its base only Insert the new lamp and turn it 90 clockwise Reverse steps 3 and 4 Use the adjustment screws marked B in the diagram to position the lamp in the center of the reflector to obtain the best output AN WARNING YAN hand Disconnect the fixture from AC power before re lamping isk of fire Protect e lot lamp Risk and eyes Lamp cover Lamp base ALWAYS turn the lamp off by using the DMX controller or the fixture s control panel Then wait at least five minutes before switching off the fixture This will keep the fans running to extract any remaining heat from the fixture s head DO NOT power cycle the fixture unless it is necessary DO NOT touch the lamp without wearing gloves to avoid leaving grease on the bulb or on the contacts that could reduce the lamp s life ALWAYS change the lamp when it has reached its recommended lifesp
37. vicing it you may find from now on in this User Manual will only apply to properly CHAUVETO certified technicians Do not open the housing or attempt any repairs unless you are one of them Please refer to all applicable local codes and regulations for the proper installation of this product Personal Safety Avoid direct eye exposure to the light source while the fixture is on Always disconnect this product from its power source before servicing Always connect this product to a grounded circuit to avoid the risk of electrocution Lamp explosion hazard Do not open the lamp cover within five minutes of having turned off the fixture The bulb remains hot for a long time after turn off Never touch the bulb barehanded and always handle it by its metallic contacts Do not touch this product s housing when operating because it may be very hot Mounting and Rigging This product is for indoor use only To prevent risk of fire or shock do not expose this product to rain or moisture Make sure there are no flammable materials close to this product while operating When hanging this product always secure it to a fastening device using a safety chain cable not provided Do not carry this fixture from the head use the handles instead Power and Wiring Always make sure that you are connecting this product to the proper voltage as per the specifications in this manual or on the product s sticker Connect this fixture ONLY to a grounded and
38. vious versions of this manual Please discard any older versions of this manual you may have whether in printed or electronic format and replace them with this version Author Editor Manager PD Manager O Desmonteix D Couppe M Graham F Sellers Use on Dimmer Auto Programs Outdoor Use Auto ranging Power Supply Sound Activated Replaceable Fuse DMX User Serviceable Master Slave Duty Cycle Legend 300E Spot User Manual Rev 01g Table of Contents CHAUVET Table of Contents Tt Betor YOU Be EE 1 E e NG EE 1 Biet te Tue Watt leen EE 1 TV DOGE AMG CONV SIMU ONNS EE 1 CONME Af ale DEE 1 Sale INES A AAA AA AS 2 a AA AA AA AA AA AE 3 IO UCD Sc IIA A 3 E AN 3 AQUINONA ROQUES EE 3 A O O AO nee et O IE 3 DMX Channel Summa Vettel eebe ge eeben 4 MODO EE 4 ee d rg 161010 018s E 5 is OS AA AA AA AA AMO 6 NAA 6 EE 6 TE FAC DIAC CIN AA HO 6 DMA NI Ms EET 6 EE 6 GODO e EE 7 PP AA 7 Eolo Vy eel EE 7 GORGE DAC CIN eM NE TEE PP e 8 Lamp FACTO AG SIN EE 9 Increasing the Lamp S EE 9 Mea AA O O O OO 0 o 10 EE 10 ROING pP 10 Bs ODE de EE EE 11 Control GERT nde ME 11 EG BA BI EE 11 Ge AG AA 11 Ho AA AA PA 11 NAVO EA ONS A q En a 11 EE 12 SAA o aanak naba AD BG Gb aan bb ia DILL Anb an bu S EG ac pba bisan 13 A RA BA 14 EE EE EE EE 15 SE 15 Fure ANO NON a a IS ei e e a e 16 ee UNCION Sen EE 16 Special er de 17 ONS lee 17 ERIE HO ONE MO AA AA AA AA 17 MENO tetro tb erc epe vm 19 DMA Vales AAA A
39. w value Select Frost and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value Select Flatb and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value Select Focus and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value Select Zoom and press ENTER a pop up window will open a Select the new value 0 255 b Accept the new value Legend 300E Spot User Manual Rev 01g Operation t Menu Map Main Level 2 Level 3 Level 4 Level DMX Address 001 52 NIA Mode 1 21 channel N A DMX Channel Mode Mode 2 29 channel N A DMX Functions View DMX Value N A N A a NU Requires optional WDMX card Reset Memory Tilt Inverse Fixture Setting BI o P T Moving No Yes N A BI O Color Change BI O Gobo Change On Off On Off State Power On Off Via DMX On if DMX On No Yes Lamp Setting N A Off if DMX Off Cooling Mode Auto High Low Power Delay 0 256s Zs 4 No Yes Backlight Auto Off Display Setting 7 N A Auto Test Fixture Test N A N A Manual Test Fixture Use Time Fixture Information Lamp On Time Exit Rest Time N A Pan Tilt Color CMY Reset Functions Shutter Dimmer No Yes N A Focus Zoom Prism Frost Iris Flatb All Fixture Maintenance Interval Remain Time Special Functions N A Factory Setting No Yes Legend 300E Spot User Manual Rev 01g 19 Operation DMX V
Download Pdf Manuals
Related Search