Bedienungsanleitung - Eickemeyer Veterinary Equipment Inc.
Contents
1. 16 17 operation manual XL A180 XL M180 safetv reference place the equipment page 2 1 Safetv reference Place the equipment 1 1 Safetv reference normal use The equipment may only be used with accessories wearing parts and disposable items which have been designated bv the manufacturer as suitable for the instrument or the safetv use of which is proven user qualification The equipment may only be used by persons who have a corresponding specialised qualification and who have been instructed in use of the equipment It is the user s responsibility to make sure the equipment is safe and operates properly before using the equipment 1 2 Place the equipment unpacking items included Carefully unpack the equipment and accessories and remove it from their packing Check for missing items and evidence of shipping damage File any complaints with the manufacture or supplier immediately Retain the original packing materials for later use These can come in handy when the equipment must be transported Please verify immediately after having unpacked the equipment whether the delivery is complete The standard extent of delivery includes of the following e light source e mains cable e usermanual e video cable Y C BNC only XL A safetv precautions at the site of installation e Alwavs place the equipment on a solid base e Make sure that air circulation is sufficient S e Nevercover the louver type2. malfunction you should check the wiring at first Most errors are based on wrong wiring The last column shows the referring chapter malfunction possible reason remedial measure equipment doesn t work line cable not connected connect line cable main switch doesn t shining Po main switch off turn main switch on both line fuses defective check line fuses exchange wrong line voltage adjusted adjust right line voltage with fuse drawer equipment doesn t work lamp after changing wrong check connector of the lamp main switch shining connected B jlampdefective change lamp fF one line fuse defective check line fuses exchange P wrong line voltage adjusted adjust right line voltage with fuse drawer intensity adjustment doesn t no signal from external video check video in connection external video in work device device must be switched on PL front panel controller defective exchange of controller wrong light guide in use exchange of light guide lamp is flashing but not ventilator blocked or defective check ventilator ignited lamp defective Cid hangellamp Cid power supply defective exchange power supply Cd life time indicator is not clock board defective exchange PCB working service manual XL A180 XL M180 spare parts 6 2 Selection of the line voltage setting To set the correct voltage proceed as follows e PULL OUT THE MAINS PLUG e Using a small screwdriver or other sharp instruments the
3. number of vour unit Please alwavs indicate these data when ordering spare parts or in case of anv question Tvpe Please enter here the technical data of your device gt Date Class Hz Amp warrantv 1 vear according to our warrantv conditions Opening the equipment or performance of anv repairs or modifications of the equipment bv unauthorised persons shall relive the manufacturer of anv liabilitv for its performance Anv such opening repair or modification performed during the warrantv period shall void all warrantv Wear parts are not included in the warranty The firm of the manufacturer shall be liable for failure or deterioration in the safe operation operational reliability and performance of this equipment only subject to the conditions that all assembly operations system expansions readjustments or repairs to same have been performed by a person or persons duly authorised by the manufacturer that all electrical installations at the location of us meet applicable national and local electrical codes and that the instrument has been used in accordance with its operating instructions at all times operation manual XL A180 XL M180 general advises signs and svmbols page 4 rights All rights on this user manual especially the rights of duplication and publication and the rights on translation are reserved No part of this user manual mav be reproduced bv anv means bv photo static copv microfilm or other methods without pre
4. black rectangular board above the socket can be lifted out e The white panel with the fuse can be taken out and turned 180 and then put back into the fuse container e After that the rectangular fuse board can be put back the small nose of the board facing downwards and firmly pressed until it has completely snapped in e Now the small white panel should show the correct voltage 6 3 Exchanging the mains fuses Mains fuses are located on the rear panel of the control unit right above the mains terminal device in a small drawer If you need to exchange the mains fuses proceed as follows e PULL OUT THE MAINS PLUG e Loosen the drawer by unfastening the two clamps located to the left and to the right of the drawer with a peaked tool and pull out the drawer e Take out the fuses e Check the fuses A blown fuse is indicated by the blackened glass cylinder or the visibly melted fuse conductor If necessary check the fuse with an ohmmeter e Install the corresponding fuses e Re install the fuse drawer e Switch on the equipment again If you have exchanged a defective fuse against a new one and the fuse blows again the unit has an error In this case you must return the device to your dealer for testing and repair 6 4 Exchanging the lamp If the life time of The lamp has expired it must be exchanged against a new one The lamp is especially stressed when switched on or off Thus it will blow when switching on or off the lig
5. ceding written consent of the manufacturer or be reproduced multiplied or published bv means of electronic data processing The information given in this user manual can be changed or extended without notice and do not represent anv liabilitv Errors and technical changes excepted attention important notel safetv notel service please read the enclosed instructions unit model BF beware of dangerous electrical voltage connection for ground potential alternating voltage PEL BBB operation manual XL A180 XL M180 description of the equipment 3 Description of the equipment This light source is a high intensitv 180 Watt XENON light source which is designed for use in every endoscopic discipline The colour temperature of 5 600 Kelvin equals the colour temperature of daylight The light source can be used with every light guide system by the simply exchangeable adapter A mechanical diaphragm is used to adjust the output intensity without any influence on the colour temperature The equipment complies with the latest safety standards for medical products and is approved to CE page 5 operation manual XL A180 XL M180 operating elements page 6 4 Operating elements 4 1 Operating elements on the front panel A LA m INTENSITY MAN AUTO RD POWER REMAINING LAMP LIFE LAMP CHG ON OFF 500h 250h 100h 50h Main switch Remaining lamp Light guide Push bottons Push bottons l
6. e correct one voltage 230VAC gt indicator 230 voltage 115VAC gt indicator 115 If the incorrect voltage is indicated then the equipment may under no circumstances be connect Before connecting a light cable into a light source adapter of the equipment please ensure that you have the correct plug and adapter A plug that is too long or too thin can for example be pushed too far into the equipment and can damage the sensitive diaphragm or lens inside This will result moreover in considerable loss of light in the same way as a plug that is too short or a plug of the wrong diameter because of the wrong position of the contacts at the light entry All wiring has to be done before switching on the equipment After switching on a light source and the ensuing ignition of the lamp the equipment should remain O switched on for at least 1 4 hour A shorter shining period will considerably shorten the life expectancy of the lamp After switching off a light source however it may be immediately switched on again A waiting period or cooling off period is not necessary CONNECT THE MAINS CABLE Use the delivered protectively earthed power supply cord to connect the control unit to the mains Please check before whether the current voltage selection matches your local mains voltage CONNECT THE EXTERNAL INPUT DEVICES only XL A As described before there are several standards of videosignal available on the rearpanel Here
7. htsource In order to exchange the lamp proceed as follows e Switch off the equipment l e Pull out the mains plug l e Unscrew the five screws located on both sides and rear of the housing and lift off the cover 1 e ifthe lamp has burned right before it may be still very hot Let it cool down before proceeding e Disconnect the lamp connector e Loosenthe hand screw and push up the lamp guard e Pull out the lamp backwards out of its holder e insert a new lamp into the holder and close the lamp guard like before e Reconnectthe lamp cable 1 e RESET THE LIFE TIME INDICATOR by switching the little red switch on the clockboard into the opposite position e Install the cover Take care that the grounding cable of the cover is installed properly e Fastenthe cover with the screws plug in the mains plug and switch on the equipment page 11 service manual XL A180 XL M180 spare parts page 12 top view cable t knurled head screw 8 lamp guard lamp plug fixed jack heat protecting filter lens optional 6 5 Further maintenance in conjunction with lamp change on the conditions in the environment This dust should be removed from the equipment with a vacuum cleaner using a small nozzle attachment Dust can sometimes cling quite firmly to the fan blades This should then be cleaned with a cloth and a little alcohol spirits Likewise dust settles on the heat pro
8. ife indicator connector increase decrease manual automatic only XL A intensity mode only XL A Main switch The control unit is turned on by switching the mains switch The mains switch has two different switching positions switched on O switched off When the control unit is switched on this is indicated by the up light green lamp inside the switch Light guide connector This connector is used to connect the light guide to the lightsource There is an interchangeable adapter screwed in The adapter used has to match the light guide fitting you are using Several adapters for all types of light guides are available Most of these adapters have an automatic snap in O for the light guide Remaining lamp life indicator only XL A Indicates the remaining life time of the XENON lamp When you switch on the light source it will start up with internal self check After 500 hours working time the indicator LAMP CHG will start flashing It is recommended to replace the lamp with a new lamp pushbuttons INCREASE DECREASE INTENSITV These buttons are used to adjust the intensity of the output in manual mode If the mechanical diaphragm is opened or closed completelv a vellow light in the switch will indicate this pushbuttons MANUAL AUTOMATIC MODE oniv XL A These pushbuttons are used to switch the light source between MANUAL and AUTOMATIC mode The actual mode is indicated bv a green light in the switch operation ma
9. ill startin MANUAL mode The output of light can now be adjusted either stronger or weaker bv the push buttons INTENSITV Then intensitv is adjusted bv a mechanical diaphragm with the result that the spectrum of white light does not change when dimmed When the diaphragm is completelv open for maximum light intensitv or completelv closed for minimum light intensitv when the respective kev is pressed this will be indicated bv the vellow LED light in the corresponding kev Using the equipment with video camera oniv XL A Connections or wiring of the equipment Besides the mains connection and the connection of the light cable with endoscope the video signal must now also be connected to the external input device Setting mode oniv XL A With standard cameras therefore for automatic brightness control through the light source you set the mode AUTO by pressing the button AUTO and the green LED in the button then lights up When vou switch on AUTO the electronics will also automaticallv switch to an average brightness from then on Setting the brightness on the monitor screen in auto mode If the automatically set picture brightness is not sufficient or if it is too bright then brightness can be adjusted brighter or darker by the button INTENSITY as with manual operation When the brightness diaphragm on the light source is completely open or completely closed this will be indicated by the yellow LED light in the brightness but
10. nual XL A180 XL M180 operating elements page 7 4 2 Operating elements on the rear Potential ground Video connector connector oniv XL A o VBS gt U A e WIN jil MMU Fuse holder Mains voltage connector Mains voltage indicator TISV 7T5A 230V T25A CC Potential ground connector When running the equipment in rooms which compiv to class 1 or 2E according to MedGV the light source must be joined to the central potential equalisation of the operating theatre or of the equipment trolley by means of a grounding cable Mains voltage connector This is the connector for mains voltage Use only the added mains cable mains fuses voltage selector This drawer contains the mains fuses The window inside the drawer shows the currently selected mains voltage You have to control whether your mains voltage corresponds with the selection shown in the window Video IN connector only XL A Here vou have to connect the external video source to run the light source in automatic mode Use only one of the connections BNC for composit VHS signal Y C for S VHS signal operation manual XL A180 XL M180 connecting and operating the equipment page 8 5 Connecting and operating the equipment Before vou connect the mains plug check on the back of the equipment that the voltage indicated in the square panel above the mains socket is th
11. onnector lamp protective class certificates manufacturer dimensions weight 8 Spare parts Lamp OSRAM XBO R180W 45C Fuses Fine fuses 5x20 mm mains fuses Power supplv Starter board XL100 180 Front panel controller automatic Front panel controller manual Clock board page 16 230 VAC 10 115 VAC 10 270 W fine fuses 5x20mm 2x T2 5A 2xT5A all lightguides connectable using interchangeable adapters Xenon high pressure lamp 180 Watt 5600 K OSRAM XBO R180W 45C BF CE ILO electronic GmbH Quickborn 355x110x325 mm WxHxD 8 5 kg 230 VAC 2x T 2 5A 115 VAC 2x T 5A service manual XL A180 XL M180 table technical service information page 17 9 Table Technical service information
12. operation manual service manual Xenon XL A180 180 Watt Xenon high intensitv lightsource with automatic intensitv control and lamp life time indicator LA mm INTENSITY MAN AUTO iI Oo POWER REMAINING LAMP LIFE LAMP CHG ON OFF 500h 250h 100h 50h Xenon XL M180 180 Watt Xenon high intensity lightsource with manual intensity control AS 8 mm ie OO POWER ON OFF INTENSITY operation manual XL A180 XL M180 table of contents 1 Safetv reference Place the equipment 1 1 Safety reference nc ts A ele al Mein nt NL Gant 1 2 Place the equipment sise 2 General advises signs and symbols 3 Description of the equipment 4 Operating elements 4 1 Operating elements on the front panel 4 2 Operating elements on the reaf serrar ena r anna 5 Connecting and operating the equipment 6 Service manual Maintenance of the equipment 6 1 possible causes remedy nn nna 6 2 Selection of the line voltage setting 6 3 Exchanging the mains fuses 2 sen ennnnnnennnnnnnnnnnnnrnnn nanna 6 4 Exchanging the lamp ii feda e a 6 5 Further maintenance in conjunction with lamp change en 6 6 Cleaning Disinfecting nn r nn nn 6 7 Wiring diagram iii ii anis een aA Eare a aana Tiaan Ea 7 Technical data 8 Spare parts 9 Table Technical service information BA E neutral XL180 2001 A doc page 1
13. slots of the unit e The equipment may be used only in rooms having electrical installations conforming to applicable national state and local electronically codes e The unit must be joined to the central potential equalisation of the operating theatre or of the equipment trolley by means of a grounding cable e The device must be connect to line voltage using the delivered protectively earthed power supply cord e The equipment may not be used in areas where there are dangerous flammable gases e The equipment may only be connect to devices which also comply to the IEC601 1 e Never look direct in the lightbeam of a light source operation manual XL A180 XL M180 general advises signs and svmbols 2 General advises signs and svmbols Thank vou for vour expression of confidence in the manufacturers brand name Like all of our other products this product is the result of vears of experience and great care in engineering and manufacture This manual is destined to learn vou understanding the function and the operation of vour equipment Before vou switch on the equipment for the first time please thoroughiv read this manual and pav special attention to all safetv instructions so that endangering for the user and the patient is precluded Please alwavs store this manual with the equipment data of the equipment page 3 The tvpe label rear of unit contains technical data tvpe and serial Serial No
14. tective filter this should also be cleaned with a soft cloth or blotting paper and pure alcohol or spirits Concerning use of flammable liquids pay attention to safety precautions After operation dust may have been sucked through the fan blades into the equipment depending D 6 6 Cleaning Disinfecting NOTE PULL OUT THE MAINS PLUG Q All parts of the outer surfaces of the equipment are totally insensitive to all the usual cleaning and disinfecting materials so that you can use any of these without limitation Apply liquids using a soft cloth or soft blotting paper in order to avoid scratches on the surfaces and in order to be able to control the amount of liquid With flammable liquids like alcohol especially you should apply with a cloth Do not let any liquid get into the equipment After cleaning with flammable liquids leave the equipment to dry for one hour before it is switched on again There is danger for example that an alcohol air explosive mixture could form after cleansing service manual XL A180 XL M180 spare parts page 13 6 7 Wiring diagram service manual XL A180 XL M180 spare parts page 14 Power supplv Front panel controller XL A service manual XL A180 XL M180 spare parts page 15 Front panel controller XL M Clock board oniv XL A Starter board service manual XL A180 XL M180 spare parts 7 Technical data Mains voltage Power consumption Mains fuses lightguide c
15. tons We remind you to leave the lamp burning for at least 1 4 hour because shorter burning period will reduce the life expectancy of the lamp After switching off the equipment it may immediately be switched on again A cooling off or waiting period is not necessary page 9 service manual XL A180 XL M180 spare parts page 10 6 Service manual Maintenance of the equipment general maintenance and repair advice The instructions and information given in this chapter are only for instructed personnel who are aware of the safetv precautions necessarv for repair and maintenance of medical electronic devices ILO electronic refuse anv liabilitv for unauthorised repair and modification The manufacturer will provide those circuit diagrams itemised parts listings descriptions sets of adjustment instructions and other items of available documentation to suitably qualified user personnel dulv authorised bv the manufacturer for their use in repairing those components of the equipment that have been designated by their respective manufactures as reparable Only the supply of such technical documentation relating to the equipment shall not be construed as constituting manufacturer s authorisation of user s personnel regardless of their levels of technical training to open or repair the equipment Explicitly exempted here from are those maintenance and repair operations described in this manual 6 1 possible causes remedy In any case of
16. you can connect external input devices If you are using standard VBS signal BNC terminal please always apply high quality 75Q coaxial cables If the external device has a switchable 75Q termination resistor you should switch this on If you connect several devices in a row only the last device in the line needs to be terminated by the termination resistor If the external device does not provide such a termination resistor vou should connect the coaxial cable via a T connection adapter The open end of the T connection adapter is then terminated with the 75Q resistor We recommend the use of the delivered S VHS cable CONNECT THE POTENTIAL EQUALISATION CONDUCTOR Join the terminal device for potential equalisation on the rearpanel with the central potential equalisation of the operating theatre or of the equipment trollev CONNECT THE LIGHTCABLE Connect the lightguide to the lightsource using a suitable adapter for vour lightguide OPERATING Switch on the equipment After connecting the mains the grounding conductor the light cable and the endoscope the equipment is readv for use and can be switched on at the mains switch on the front panel The green mains light Power inside the switch will light up The lamp will automaticallv ignite It will burn with full power right from the start operation manual XL A180 XL M180 connecting and operating the equipment Setting the light intensitv MANUAL mode The light source w
Download Pdf Manuals
Related Search