User manual
Contents
1. ANC LED indicator status left side of headphones Headphones status Indicator Active noise cancelation The green LED is on is on Awareness mode is on The green LED flashes m Active noise cancelation and The green LE awareness mode is off is off Connect to airline audio systems 1 Connect the audio cable into the airline adapter 2 Insert the adapter into the dual output jacks in the airplane seat One 3 5mm jack Use the single plug No adapter is needed O Two 3 5mm jacks Use the 3 5mm dual plug airline adapter OO One power Jack and two 3 5mm jacks Use the 3 5mm dual plug airline adapter Make sure you insert it into two 3 5mm Jacks O OO Wear your headphones Adjust the headband to fit your head Tip e After use twist the headphones for easy storage EN 9 5 Technical data Music time ANC enabled with Bluetooth 16 hours Talk time ANC enabled with Bluetooth 15 hours Standby time ANC enabled with Bluetooth 45 hours e Music and talk time Unlimited with audio cable connected ormal time for a full charge 2 hours e Rechargeable Lithium Polymer battery 530 mAh e 3 5 mm audio jack for corded headphones mode e Bluetooth 4 0 Bluetooth mono support Headphones Profile HSP Hands Free Profile HFP Bluetooth stereo supported Advanced Audio Distribution Profile A2DP Audio Video Remot2. EN 3 Get started Charge the battery E e Before you use your headphones for the first time charge the battery for 5 hours for optimum battery capacity and lifetime e Use only the original USB charging cable to avoid any damage e You can operate the headphones normally during charging Normally a full charge takes 2 hours e When the battery level is low the white LED will flash Connect the supplied USB charging cable to e the micro USB charging port on the headphones and e the charger USB port of a computer Pair the headphones with your mobile phone Before you use the headphones with your mobile phone for the first time pair it with a mobile phone A successful pairing establishes a unique encrypted link between the headphones and mobile phone The headphones store the last 8 devices in the memory If you try to pair more than 8 devices the earliest paired device is replaced by the new one There are two ways to pair your headphones with your mobile phone e Manual pairing e NFC pairing Manual pairing 1 Make sure that the headphones are fully charged 2 Press and hold to turn the headphones on L gt For previous device pairing the white LED flashes once and the blue LED flashes L gt For new device pairing press and hold until the blue and white LED flashes alternately 3 Tum on the Bluetooth function of your mobile phone L gt The headphones
3. and result in personal injury e Never use your headphones when you are operating a motor vehicle riding a bicycle running or walking in traffic areas It is dangerous and illegal in many places About operating and storage temperatures and humidity e Operate or store in a place where temperature is between 15 C 5 F and 55 C 131 F up to 90 relative humidity e Battery life may be shorter in high or low temperature conditions 2 Your noise canceling on ear Bluetooth headphones Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Quick start guide VWieteinthebex Other devices A mobile phone or device e g notebook PDA Bluetooth adapters MP3 players etc which supports Bluetooth and is compatible to the headphones see Technical data on page 10 Overview of your noise canceling Bluetooth headphones Philips noise canceling on ear Bluetooth headphones SHB9850NC IN d 000 USB charging cable PHILIPS Audio cable O Micro USB charging slot Ci Music Call control button OGG OO OOO Audio jack LED indicator U Power button Microphone Q Pairing Mute button NFC detection area Active noise canceling ANC on off button Active noise canceling ANC LED indicator
4. are in pairing mode for 5 minutes air the hea ones with the mobile 4 Pair the headph ith the mobil phone For detailed information refer to the user manual of your mobile phone NFC pairing 1 Make sure you turn on the NFC function on your phone and your phone s screen remains active 2 Place your phone over the headphones so that the NFC detection area of each device can touch each other 3 Pair the headphones with the mobile P phone For detailed information refer to he user manual of your mobile phone Note e Make sure your mobile phone has the NFC feature available and switched on Make sure your mobile phone is not in standby mode Pairing with NFC is only suitable for Android mobile operating system 4 2 or above e Refer to the user manual of your mobile phone to identify its NFC detection area The following example shows you how to pair the headphones with your mobile phone T Activate the Bluetooth feature of your mobile phone select Philips SHB9850NC 2 Enter the headphones password 0000 4 zeros if prompted For those mobile EN 5 phones featuring Bluetooth 3 0 or higher no need to enter a password Add Philips SHB9850NC Enter Password Bluetooth device 0000 4 U se yo u r a control Siri Google Now press h ead p h ones W control Play or pause music tap once Connect to Bluetooth Connect the headphones to a Bluetooth device e Volu
5. forth for uncontrolled environments This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Trademarks Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Gibson Innovations Limited is under license Other trademarks and trade names are those of their respective owners EN 11 Siri Siri is a trademark of Apple Inc registered in the US and other countries Google Google and the Google Logo are registered trademarks of Google Inc N Mark The N Mark is a trademark or registered trademark of NFC Forum Inc in the United States and in other countries 12 EN 7 Frequently asked questions My Bluetooth headphones do not switch on The battery level is low Charge the headphones cannot pair my Bluetooth headphones with a mobile phone The Bluetooth is disabled Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headphones Pairing does not work Make sure the headphones are in pairing mode e Follow the steps described in this user manual see Pair the headphones with your mobile phone on page 5 e Make sure that the LED light flashes blue and white alternately before you release Do not stop holding the button if you see he blue LED only The mobile phone cannot find the head
6. or more of the following measures e Relocate the receiving antenna e Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body This transmitter must not be co located or operated in conjunction with any other antenna or transmitter Caution Changes or modifications made to this equipment not expressly approved by Philips may void the FCC authorization to operate this equipment Model number SHB9850NC Trade Name Philips Responsible party P amp F USA Inc PO Box 2248 Alpharetta GA 30023 2248 1 866 310 0744 Notice for Canada This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 IC Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set
7. Always there to help you Register your product and get support at www philips com support i Question Contact SHB9850NC Philips User manual PHILIPS Contents 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your noise canceling on ear Bluetooth headphones 3 What s in the box 3 Other devices 3 Overview of your noise canceling Bluetooth headphones 3 3 Get started 5 Charge the battery 5 Pair the headphones with your mobile phone 5 4 Use your headphones 7 Connect to Bluetooth 7 Connect to ANC active noise cancelation 8 Connect to airline audio systems 9 Wear your headphones 9 5 Technical data 10 6 Notice 11 Notice of compliance 11 Trademarks 11 7 Frequently asked questions 13 EN 1 Important safety instructions Hearing Safety Danger e To avoid hearing damage limit the time you use headphones at high volume and set the volume to a safe level The louder the volume the shorter the safe listening time is Be sure to observe the following guidelines when using your headset e Listen at reasonable volumes for reasonable periods of time e Be careful not to adjust the volume continuously upwards as your hearing adapts Do not turn up the volume so high that you can t hear what s around you You should use caution or temporarily discontinue use in potentially hazardous situations Excessive sound pressure f
8. de of headphones Headphones status Indicator The headphones are The blue LED connected to a Bluetooth flashes for every device while the 8 seconds headphones in standby mode or while you are listening to music The headphones are ready The LED flashes for pairing blue and white alternately The headphones are on The blue LED but not connected to a flashes quickly Bluetooth device Low battery The white LED flashes slowly The white LED is off Battery is fully charged Wired connection You can also use the headphones with the audio cable provided when the battery is too low Make sure the headphones turned off before using the audio cable Connect the supplied audio cable to the headphones and external audio device Connect to ANC active noise cancelation Enable ANC e Press and hold the ANC on off button for 2 seconds to enable noise cancelation e Press and hold the ANC on off button for 2 seconds to disable noise cancelation Tip e When the ANC function is not required switch off the ANC on off button to continue your call or listening to music Enable awareness mode e Press the ANC on off button to enable awareness e Press the ANC on off button to disable awareness L gt The ANC function will be on off automatically Note e The awareness mode can be enabled only when ANC is also enabled
9. e Control Profile AVRCP e Operating range Up to 10 meters 33 feet e Digital echo amp noise reduction e Auto power off e Active noise cancelation Hybrid 4 microphones e Low battery warning available Note e Specifications are subject to change without notice 6 Notice Notice of compliance Notice for US This set complies with the FCC rules Part 15 and with 21 CFR 1040 10 Operation is subject to the following two conditions D This device may not cause harmful interference and Q This device must accept any interference received including interference that may cause undesired operation FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of protection against harmful inte residential installation This equi uses and can radiate radio freq and if not installed and used in he FCC Rules These limits are designed to provide reasonable rference ina pment generates uency energy accordance with the instruction manual may cause harmful interference to radio commun ications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged o try to correct the interference by one
10. me up slide up or slide up and hold T Tumon your mobile phone Bluetooth device 2 Press and hold to turn the headphones on t The blue LED flashes L gt The headphones are reconnected Volume down slide down or slide down to the last connected mobile phone and hold Bluetooth device automatically Ea e Ifyou turn on the mobile phone Bluetooth device or activate the Bluetooth feature after turning on the headphones you have to reconnect the headphones and mobile phone Bluetooth device manually Skip forward slide forward e If your mobile phone Bluetooth device cannot reconnect automatically try to reconnect manually by clicking the headphones name again under the Bluetooth setting manual on your mobile phone Bluetooth device Note B e Skip backward slide backward e Ifthe headphones fail to connect to any Bluetooth device within range in 5 minutes it will switch off automatically to save the battery life Manage your calls and music On off e Turn the headphones on press and hold for 4 seconds e Turn the headphones off press and hold for 4 seconds L gt The white LED is on and fades out EN Call control e Pick up hang up a call tap once Reject an incoming call tap and hold e Switch caller during a call slide forward e Mute unmute the microphone in a call press LED indicator status right si
11. page 10 My headphones do not work when the audio cable is connected Microphone function will be deactivated if a 3 5mm audio cable is connected to the headset In such case your headphones are only for music enjoyment For further support visit www philips com support EN 13 2015 Gibson Innovations Limited All rights reserved This product has been manufactured by and is sold under the responsibility of Gibson Innovations Ltd and Gibson Innovations Ltd is the warrantor in relation to this product Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N V and are used under license from Koninklijke Philips N V UM_SHB9850NC_27_EN_V1 0 wk1533 PHILIPS
12. phones e The headphones may be connected to a previously paired device Turn off the connected device or move it out of range e Pairing may have been reset or the headphones have been previously paired with another device Pair the headphones with the mobile phone again as described in the user manual see Pair the headphones with your mobile phone on page 5 Voice dialing or redialing does not work on my mobile phone Your mobile phone may not support this feature The other side cannot hear me on the mobile phone The microphone is muted Press once to enable the microphone My Bluetooth headphones are connected to a Bluetooth stereo enabled mobile phone but music only plays on the mobile phone speaker Refer to the user manual of your mobile phone Select to listen to music through the headphones The audio quality is poor and crackling noise can be heard The Bluetooth device is out of range Reduce the distance between your headphones and Bluetooth device or remove obstacles between them The audio quality is poor when streaming from the mobile phone is very slow or audio streaming does not work at all Make sure your mobile phone not only supports mono HSP HFP but also supports A2DP see Technical data on page 10 hear but cannot control music on my Bluetooth device e g play pause skip forward backward Make sure the Bluetooth audio source supports AVRCP see Technical data on
13. rom earphones and headphones can cause hearing loss Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving e For your safety avoid distractions from music or phone calls while in traffic or other potentially dangerous environments General information To avoid damage or malfunction EE Caution Do not expose headphones to excessive heat Do not drop your headphones e Headphones shall not be exposed to dripping or splashing Do not allow your headphones to be submerged in water e Do not use any cleaning agents containing alcohol ammonia benzene or abrasives If cleaning is required use a soft cloth if necessary dampened with a minimum amount of water or diluted mild soap to clean the product e The integrated battery shall not be exposed to excessive heat such as sunshine fire or the like e Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type e Use only the Philips airline adapter to connect the headphones to airplane seat jacks Do not use other airline adapters as they might not result in correct response or even result in personal injury such as burns or property damage due to overheating Remove the adapter and disconnect immediately if you experience warming or loss of audio Do not insert any plug into the power jack of the airplane seat because it may damage the headphones
Download Pdf Manuals
Related Search