Model QS-5A - DirectedDealers.com
Contents
1. Turn your windshield wipers to the OFF position Make sure gearshift is in P THE REMOTE CONTROL Your remote control has been designed to fit the natural contours of your hands so that it is easier to use It works off three long life lithium batteries It can control two vehicles separately Up to four remote controls can be assigned to your vehicle See your dealer for replacement batteries or additional remote controls NOTE The range of your remote control can be affected by a weak battery interference from nearby metal structures hydro poles or crowded parking lots USING YOUR REMOTE CONTROL Your remote control can transmit on two different channels allowing control of two separate vehicles Only the Panic command is transmitted on both channels Stop simultaneously Panic Each command being transmitted is confirmed by both an audible and a visual signal LED indicator LED Unlock Disarm CHANNEL 1 CHANNEL 2 To transmit a command To transmit a command on channel 2 press desired button then on channel 1 press as soon as a tone is heard or LED flashes once release the button desired button for two for a moment then press it again and hold it down for two seconds seconds A command will not be executed if you do not press button long enough Only one command will be transmitted even if a button is pressed for more than two seconds except for the Stop button that will send a Panic comm2. CHECKS 17 HOOD SWITCH 17 GEARSHIFT CHECK 17 REPLACING OR BOOSTING VEHICLE BATTERY 17 SAFETY PRECAUTIONS Before using this product carefully read the following safety precautions Immediately report any malfunction to the dealer that performed installation Under no circumstance can this product or its use be modified Always turn off main switch when vehicle is parked in an enclosed unventilated area or is in for servicing Always turn off main switch when not using your Remote Starter for extended periods of time Keep remote controls away from children Have your engine tuned regularly to ensure optimum performance of your Remote Starter Make sure your windshield wipers are turned off before leaving vehicle Regularly check safety features that stop engine see SAFETY CHECKS on page 17 Make sure you comply with all local regulations which may prohibit leaving your engine running when vehicle is unattended in a public place Always advise service personnel that your vehicle is equipped with a Remote Starter equipped with a starter cut function We strongly recommend that you have your system checked annually Contact the dealer in your area BEFORE USING YOUR REMOTE STARTER Before leaving your vehicle set the various controls in order to use your Remote Starter Set heating air conditioning controls to desired position When the remote starter starts your engine it will also turn on your climate control system
3. at least one door is opened Once the zone is corrected e g door closed the system sends another confirmation one chirp or flash if all zones are in normal condition three chirps or flashes if another zone is in violation If a zone is in violation when system is armed manually using remote and the cause of the violation is not corrected the alarm will still arm but this zone will not be able to generate an alarm condition See also DOME LIGHT DURATION When you disarm the alarm two chirps or flashes indicate that no one tried to break into or do anything to your vehicle and four chirps or flashes indicate that an alarm condition occurred during your absence The following table summarizes this section CONFIRMATION MEANING 1 chirp or flash System armed no zone in violation 2 chirps or flashes System disarmed no violation detected 3 chirps or flashes System armed with zone in violation Indicator light indicates which zone System disarmed with violation detected 4 chi flash sS ss Indicator light indicates cause of alarm condition 10 INDICATOR LIGHT Indicator light flashes a specific number of times see table below to indicate different alarm conditions when arming and disarming the system It can also act as a deterrent if installed in a place visible from outside the vehicle DURING ARMING Indicator flashes codes for zones in violation e g at least one door is opened Only on
4. corrected or not Shock sensor Each period is separated by a 5 second pause Ignition key 45 seconds for Door zone DETERRENTS ACTIVE When one of the monitoring devices detects a violation system reacts by activating the following deterrents depending on which is connected System can activate up to four deterrents simultaneously siren parking lights dome light and or horn PREVENTIVE Indicator light shows different alarm conditions see ZONE CODES on page 11 It can also act as a deterrent if installed in a place visible from outside vehicle ALARM MODES WARNING Warning signal is 7 siren chirps If a two level shock sensor is connected to system warning sounds every time vehicle is subjected to a light shock when the alarm is armed PRE ALARM If you set off alarm by accident and do not want to alarm or disturb the whole neighborhood pre alarm mode cuts in three seconds before alarm condition to give you time to disarm system In this mode parking lights siren and dome light go on and off intermittently for three seconds ALARM CONDITION When system is in alarm condition it activates the various deterrents connected to the alarm module Alarm condition remains active for 30 or 60 seconds depending on initial programming then system pauses for five seconds 45 seconds for Door zone During this pause it checks the protection zones again and restarts alarm cycle if a zone is still in violation This cycle
5. E Qr a Press buttons Qe and a simultaneously parking lights 1 4 Parking lights flash one to four times to indicate selected runtime N see table opposite Eee of Runtime If you send this command while the ignition circuits are activated by remote or key runtime does not change but confirmation is 1 2 minutes sent to indicate last selection 2 4 minutes If Low Temperature Sentinel mode is already activated when 3 8 minutes this command is sent the command sets or indicates Low 4 18 minutes Temperature mode runtime Note Runtime is doubled for a diesel engine 1 A runtime of 2 minutes 4 min for a diesel engine is not recommended for most vehicles unless you intend to drive off immediately after the remote start This selection is not available in Low Temperature mode 7 SECURITY SYSTEM PROTECTION ZONES Your security system can use up to six different monitoring devices simultaneously to protect your vehicle These devices are connected to the system on different inputs called protection zones One of these zones can send an audible warning 7 chirps while the other five generate an alarm condition if system is armed PROTECTION ZONES FUNCTIONS Pre shock i i S hirps 7 t more than 3 times within 3 min iren chirps umes Doors Siren ON for 30 or 60 second period which can be repeated Hood up to 4 times depending on initial programming and whether Additional sensor Trunk violated zone is
6. RARY VALET MODE IS ACTIVATED IF COMMAND IS REPEATED DURING REARM CYCLE WHEN AALRM SET IN PASSIVE REARMING AT THE INSTALLS 2 NO ZONE WAS IN VIOLATION WHILE 4 ATLEAST ONE ZONE WAS IN VIOLATION ALARM WAS ARMED WHILE ALARM WAS ARMED 2 DEACTIVATION 3 SYSTEM NOT READY 4 ACTIVATION D ONLY IF SYSTEM IS EQUIPPED WITH A SENSOR CAPABLE OF DETECTING TRUNK RELEASE OPTIONAL CONFIRMATION In all cases your Remote Starter will confirm that command has been received properly This will be done by either sounding horn and or siren or flashing parking lights In this manual confirmation signals are written in an abbreviated form for example horn 1 lights 2 Means that horn will sound once and parking lights will flash twice Parking light confirmations are mandatory Horn confirmations are optional programmable and require an additional connection and equipment during installation Confirmations are explained in more detail under each command START COMMANDS STARTING THE ENGINE Qr To start the engine press Qum button horn 0 lights 1 The system automatically adjusts ignition duration for your type of vehicle parking lights flash once duration four seconds then stay on all the time engine is running If more than one command is emitted each successive start command resets runtime to the beginning parking lights flash once to confirm command has been received and horn sounds once to let you know engine is a
7. REMOTE CONTROL wruwrecrareo QS SERIE ALARM SYSTEM Model QS 5A For all automatic transmission gas and diesel powered vehicles CONSULT SAFETY PRECAUTION SECTION BEFORE USING THIS PRODUCT NEVER USE THIS PRODUCT ON A MANUAL TRANSMISSION VEHICLE SOME FEATURES MAY REQUIRE ADDITIONAL MATERIAL NOT INCLUDED FRANCAIS AU VERSO PATENT NOS CAN 1 130 426 USA 4 345 554 5 614 883 5 617 819 5 673 017 AND OTHER PATENTS PENDING ms F vm Printed in Canada 09 03 193 127 314 00 GOVERNMENT REGULATIONS This device complies with the requirements of Industry Canada IC Management of Radio frequencies as specified in document CNR 210 Its use is authorized only on a no interference no protection basis in other words this device must not be used if it is determined that it causes harmful interference to services authorized by IC In addition the user of this device must accept any radio interference that may be received even if this interference could affect the operation of the device This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide
8. SABLER Programmable as Active or Inactive during installation Your Remote Starter is equipped with an Antitheft system This system consists of an output that controls a relay that disables all circuits required to operate your vehicle optional connection Two types of Antitheft can be use PASSIVE ARMING TYPE ANTITHEFT Ef This type of Antitheft system arms automatically when ignition key is turned from ON to OFF and remains OFF for one minute It can also be armed manually by sending a Lock command unless ignition key is in ON position DISARMING Antitheft system is disarmed for one minute when you send Unlock command If ignition key is not turned to ON position within one minute system automatically rearms thus preventing an intruder from starting your vehicle even with the ignition key It can be connected so that horn sounds if an intruder tries to start your vehicle when it is in the active state 14 ACTIVE TYPE ANTITHEFT Ef This type of Antitheft system arms by sending the Lock command unless ignition key is in ON position and disarms by sending the Unlock command VALET MODE CIRCUIT DISABLER The circuit disabler function can be deactivated for the same reasons and in the same way as the Antitheft system See Valet mode details on page 12 UTILITY COMMANDS Two additional commands control most of your vehicle s accessories depending on w
9. The Continuous Mode function lets you remove the key from ignition while leaving the engine running This convenient feature allows you to leave vehicle for short periods of time while climate controls remain on To access Continuous Mode send Start command while engine is idling See STARTING THE ENGINE on page 5 Parking lights engine and preset accessories will remain on for the duration of the programmed runtime see Setting the runtime on page 7 Remove key exit vehicle and lock doors All safety devices will remain active If you return to your vehicle before runtime has elapsed just turn the key to the ON position and depress brake pedal WHAT STOPS THE ENGINE For your safety engine will not start or it will stop if z Ignition key is in RUN position prevents start n Remote control sends a stop command z Hood is open n Brakes are applied Alarm is in infraction condition Engine is over revving if engine over revving monitoring is active Main switch is OFF MAIN SWITCH Main switch is usually mounted under dashboard When it is placed in the OFF position it cancels all start related functions but does not disable other commands which remain active alarm door locking etc sToP When engine is kept running by Remote Starter you can stop it with this command lights 1 The stop command also ends panic mode and alarm condition LOW TEMPERATURE MODE Or In Low Temperature Sentine
10. and if hold more than 4 seconds The remote control supplied in the kit may differ from the one illustrated above BATTERY REPLACEMENT Your remote works off three 3 volt lithium CR 2016 batteries or equivalent We strongly recommend that you keep a replacement set in your glove compartment To replace the batteries remove screw on back of remote case remove old batteries and replace with new ones Make sure that batteries point the right way see illustration opposite 3 CR 2016 TABLE OF COMMANDS BUTTONS CONFIRMATION PICTOGRAM 30 60 30 60 S SEC EC S RU NE PANIC START CONTINUOUS MODE LOCK ARM UNLOCK DISARM BewweDecwwes meo Owe o howemewe Gus How ewe wf me _ Rmemamer Ow 7a exrmewwexumer erf emm Af 3 Dewmaeesw mec Owe re Dewmmuecxs A pe 9 THIS CONFIRMATION IS SENT ONLY IF START COMMAND IS REPEATED WHEN ENGINE IS ALREADY RUNNING THIS COMMAND TERMINATES RUNTIME PANIC MODE AND ALARM CONDITION WHEN CHIRPS OR ALARM IS DEACTIVATED o WHEN CONFIRMATION ON 2ND LOCK IS ENABLED THESE CONFIRMATIONS ARE PROGRAMMABLE AS ACTIVE INACTIVE DURING INSTALLATION 9 1 NO ZONE IS IN VIOLATION DURING ARMING 3 ATLEAST ONE ZONE IS IN VIOLATION DURING ARMING X NO CHIRP WHEN VALET MODE IS ACTIVE OR WHEN ALARM IS PROGRAMMED AS DISABLED e TEMPO
11. can be repeated up to four times If situation that caused the violation is corrected in mid cycle alarm stops at end of current cycle OPERATION Your alarm system has three different operating modes active semi passive rearming and passive rearming depending on initial programming See the relevant paragraph for mode your system was configured in during installation ACTIVE In active mode the alarm must be armed and disarmed using the remote see Table of Commands on page 3 Alarm is armed as soon as command is received even if a zone is in violation when command is received However violated zone cannot trigger the alarm unless it was in a normal condition beforehand This mode is always available even if during installation your system was not configured for it SEMI PASSIVE REARMING In semi passive mode alarm must be armed and disarmed using the remote see Table of Commands on page 3 In this mode alarm rearms automatically 25 seconds after disarming rearming cycle if doors are all closed Indicator light flashes rapidly to indicate that system is in rearming cycle Note If vehicle is equipped with power locks interfaced with the system a device can be added to prevent doors from locking during rearming if key is still in ignition If applicable this device allows system to be armed but cancels locking Key detection device is _ is not _ installed on this vehicle Following table shows effect of each zone on rearmi
12. e code is shown at a time If more than one zone is in violation during arming code changes when zone shown is corrected example door closed DURING DISARMING Indicator flashes code for last zone that generated the alarm condition Code is shown when you press e button This code is repeated until you apply the brakes The following table shows the meaning of zone codes number of flashes ZONE CODES FLASHES ZONE INDICATED 1 System is armed 2 A door is was open 3 Hood is was open 4 Alarm condition is was detected on shock sensor input 5 Key is was in ignition position IGN 6 Alarm condition is was detected on additional sensor input Additional sensor monitors status of ssssssss 7 Loss of power 12V battery supply was removed 8 Alarm status is has been detected on pre shock sensor input Indicator can show two other conditions CONSTANT DIM LIGHT Indicates that alarm is permanently disarmed See VALET MODE on page 12 RAPID FLASHES Indicates that system is in rearming cycle See PASSIVE REARMING and SEMI PASSIVE REARMING on page 14 SECONDARY FUNCTIONS ANTI LOCK When connected to ignition key cylinder this function prevents system from locking the doors during automatic rearming if key is in the ignition It can also be connected to a switch to select automatic locking as ACTIVE or INACTIVE TEMPORARY VALET MODE ALARM This mode is used to cancel automatic rearming for an indefinite period of t
13. ehicle is equipped with a factory security system and runtime expires during rearming cycle factory security system is reactivated but not the remote starter security system because opening a door is simulated for factory system rearming 9 The following table shows the effect that each zone has on the rearming cycle Protection zone Effect on rearming cycle Hood Doors These four zones prolong rearming cycle as long as they remain in Additional sensor Trunk violation Shock sensor Ignition Activated by ignition key Cancels rearming Activated by remote starter No effect Warning No effect Applying brakes or ignition key in ON position cancels rearming until a door is opened which causes rearming cycle to restart from the beginning See also TEMPORARY VALET MODE and DOME LIGHT DURATION You can disarm only with remote control by pressing ef button see Table of Commands on page 4 System is disarmed immediately and restarts rearming cycle from the beginning TO TERMINATE ALARM CONDITION You can terminate alarm condition by pressing e button which also disarms system or by pressing either of the or a buttons which terminates alarm condition without disarming system CONFIRMATION When the alarm is armed one chirp of the siren and or flash of the parking lights means that all protection zones are in normal condition and system is ready Three chirps or flashes means that one or more zones are in violation e g
14. hich were connected during installation headlight defroster etc For details consult your technician Commann 1 A RS To activate this function press a and Re buttons simultaneously lights 1 The accessory associated with this command is then activated for 1 second O 1 minute L or 8 minutes L depending on programming This duration can be cancelled by repeating command lights 1 COMMAND 2 E We To activate this function press ef and Re buttons simultaneously lights 1 The accessory associated with this command is then activated for 1 second g 1 minute L or 8 minutes Lj depending on programming This duration can be cancelled by repeating command lights 1 CAR FINDER d ef Press a and ef buttons simultaneously lights 3 horn 7 This function sounds horn short tune and flashes parking lights to help you locate your vehicle in a large parking lot PANIC gt 4 SEC Press button lt and hold it for more than 4 seconds This command activates all deterrents that are connected to the system parking lights horn siren and dome light for 30 sec O or 60 sec L depending on programming made during installation Panic mode is used to attract attention if you are experiencing difficulties This command will not be executed if engine is kept running by ignition key Use the stop command to abort panic mode or press brake pedal 15 START FAIL CODES Qe ef When a remote start atte
15. ime You will find this mode useful when fuelling up or working on your vehicle To activate Temporary Valet Mode press ef button during rearming cycle indicator light flashes rapidly When light stops flashing it confirms that Temporary Valet Mode has been activated To cancel this mode place ignition key in RUN position then remove it passive rearming is reactivated when you open a door You can also arm the system using the remote which cancels Temporary Valet Mode 11 VALET MopE This mode is used to deactivate alarm permanently when you take your vehicle in for servicing for example Valet switch activates Valet Mode or terminates alarm condition when your remote control is not available lost batteries dead etc This switch must be installed in a hidden place known only to regular users of the vehicle Ask your installer to tell you where it is TO ACTIVATE VALET MODE place ignition key in ON position then press Valet switch for about 3 seconds until indicator light comes on at half brightness TO DEACTIVATE VALET MODE place ignition key in ON position then press Valet switch for about 3 seconds until indicator light goes out Notes If you perform both sequences one after the other you need to pause for 3 seconds between the two sequences Valet Mode is automatically deactivated when key is turned to the ON position and or engine is remote started for the tenth time This is to prevent Valet M
16. kept on by vehicle s factory system Special condition If during dome light duration a Lock command is sent while a door is opened system arms and ignores door violation if door is still open 45 seconds after dome light duration ends system recognizes door violation and changes to alarm condition E 12 LOCKIUNLOCK COMMANDS AND ALARM SYSTEM ARMINGIDISARMING If your vehicle is equipped with electric door locks several functions can be operated by remote control These features are optional and may require purchasing additional equipment Consult your dealer for advice Arming and disarming the security system also controls Lock Unlock functions Following systems can be controlled Door locks e Trunkorhatchback release Interior lights LOCK ARM amp Press the a button doors are locked and alarm system is armed parking lights flash once and siren chirps once to confirm command has been received and that none of the protected zones are in violation Parking light confirmation is sent as many times as command is repeated so you are sure that system has received the command Audible confirmation is also repeated siren or horn depending on programming if option Confirmation on 2nd lock is activated during installation If a zone is in violation during arming confirmation is different 3 flashes or chirps to warn you See table of alarm codes to know which zone is in violation UNLOCK DISARM Ef P
17. l mode system starts your engine automatically when temperature falls below a preset level Engine will run for programmed runtime after which system will wait 272 hours and then start engine again if temperature is still below preset level To activate deactivate Low Temperature mode press Qum and buttons simultaneously When mode is activated Parking lights will flash 4 times then if temperature is below preset level engine will start If temperature is above preset level system waits until it goes below preset level before starting If system cannot execute command for example safety sequence is not valid hood is open etc confirmation will be different lights 3 When mode is deactivated Parking lights will flash twice to confirm that mode is deactivated Applying brakes also deactivates Low Temperature mode SETTING THE START TEMPERATURE rs fi To change preset temperature at which you want your Remote Starter to start engine press and buttons simultaneously lights 1 4 Parking lights will flash from 1 to 4 times to indicate selected start t t tabl it Number of Preset start emperature see table opposite Flashes temperature If you send command when ignition has been turned on by s z Remote Starter or key preset start temperature does not 1 5 C 23 F change However confirmation is still sent to indicate last 2 15 C 5 F selection 3 20 C 7 F 4 30 C 22 F SETTING THE RUNTIM
18. lready running Repeating this command will produce an audible confirmation that engine has started which can be useful if vehicle is not in sight F ENGINE FAILS TO START If your system cannot start your engine at first attempt it will wait for a few seconds and then try again it could try again twice depending on reason for failure to start After three attempts it will shut down automatically and wait for new command see Start fail Codes on page 15 UPON ENTERING YOUR VEHICLE To prevent engine from turning off when you enter your vehicle do not depress brake pedal before having placed key in ignition and turned it to ON position AN DO NOT TURN IGNITION KEY TO START POSITION Drive as usual ENGINE RUNTIME Your engine will stop automatically after a preset time see Setting the runtime on page 7 Parking lights will stay on as long as engine is running TRIGGER INPUT Your remote starter is equipped with a negative trigger pulse input This input can be connected to another remote control device or to a timer output optional If this input is connected consult this device s manual or ask your technician which command controls the Start Stop function The Start Stop commands received on this input are ignored while the engine is running on a remote start All Start Stop functions controlled by this input behave in the same way as functions controlled by remote CONTINUOUS MODE Qr
19. mpt fails it is possible to determine what caused the failure to start Press the Qu and ef buttons simultaneously The number of times the parking lights flash corresponds to the start fail code The table below lists the various start fail codes Code Failure to start details 1 Module has received a Stop command remote or timer 2 Brakes were applied during or after start sequence or module overload occurred 3 Stopped by alarm 4 Engine does not crank when starting sequence is initiated 5 Start command ignored because hood is open 7 Start command ignored because key is in ignition in Run position 8 Remote starter main switch is OFF or output overload 9 Runtime has elapsed 10 Remote starter attempted to start engine three times unsuccessfully 11 Remote starter sensed engine was already running 12 Engine is over revving RPM gt 3000 13 Engine not cranking fast enough during start sequence 16 Internal failure of module If any of these start fail codes persist consult your dealer ALARM CONDITION CODES A Use this command to identify which zone is in violation during arming or which generated alarm condition Press ana a buttons simultaneously parking lights will flash number of times corresponding to code for protection zone in violation If more than one zone is in violation code for the zone with highest priority is shown 1 highest priority See table of code
20. ng cycle Protection zone Effect on rearming cycle Hood Y a Additional sensor Trunk These three zones prolong rearming cycle as long as they remain in violation Shock sensor Ignition Activated by ignition key Cancels rearming Activated by remote starter No effect Doors This zone cancels rearming completely Warning No effect Applying brakes or activating Temporary Valet Mode cancels rearming PASSIVE REARMING In passive rearming mode opening a door triggers rearming cycle Alarm will be armed 30 seconds after checking that all protection zones are in normal condition This 30 second period is called rearming cycle If a zone detects a violation during rearming cycle countdown stops and restarts at 30 seconds when all zones are back in normal condition During rearming cycle indicator light flashes rapidly After five seconds system sends an audible confirmation siren chirps once indicating that system will arm after 25 seconds After this delay alarm is armed and sends a second confirmation siren chirps once and parking lights flash once to indicate that system is armed If you wish to remain in vehicle without driving off you can cancel rearming cycle by applying brakes When you exit the vehicle cycle resumes and system arms automatically see also TEMPORARY VALET MODE If you disarm the system and do not open the door within 60 seconds it rearms itself automatically 2 If v
21. ode from being left on for long periods of time GLOSSARY SIREN Siren has six different sounds i e it chirps repeatedly and has six different melodies It chirps intermittently short repeated chirps during a pre alarm and continuously during an alarm condition It can confirm arm and disarm commands with short chirps see table in CONFIRMATION section This function is programmable as active or inactive during installation HORN Horn beeps intermittently short repeated beeps during an alarm condition This function is optional and may require the installation of additional material Ask your installer for more details PARKING LIGHTS Parking lights flash intermittently repeated flashes during a pre alarm and alarm condition Parking lights also confirm that commands have been received See table in CONFIRMATION section VIOLATION Violation means a situation that causes a protection zone to generate an alarm condition example a door was opened etc DOME LIGHT DURATION The system turns vehicle dome light on for 30 seconds upon unlocking command not applicable in semi passive rearming mode In passive rearming mode system ignores the Door zone while dome light is on which prolongs rearming cycle by 30 seconds On some vehicles dome light may remain on after all doors have been closed If this option applies to your vehicle rearming cycle is prolonged by the number of seconds during which dome light is
22. onfirmation as often as you wish Remember to rearm alarm after trunk is closed Lock command SYSTEM EQUIPPED WITH AN ADDITIONAL SENSOR L If your system is equipped with a sensor designed to monitor status of trunk added at time of installation parking lights will flash three times to confirm command was received When trunk is released 3 chirps are emitted to warn that alarm will not take into account the status of this zone or the shock sensor s zone for the next 5 minutes If you do not release trunk within 10 seconds the system will rearm trunk automatically The timer is reset each time the command is repeated which allows for a new 5 minute period to close the trunk lid The system will sound a chirp when trunk is closed to confirm it has been rearmed If trunk is open for more than 5 minutes the system switches to alarm status AUTOMATIC LOCK UNLOCK Programmable as Active or Inactive during installation This function locks the doors when ignition key is in ON position engine is running and brakes are applied Doors are unlocked when key is turned from ON to OFF or when Continuous Mode is activated If Unlock function is set to unlock only driver s door on the first command the Automatic Unlock function will unlock driver s door only If dome light is connected to system it is activated when an automatic unlock OCCUIS This function is Active _ Inactive _ OTHER COMMANDS ANTITHEFT CIRCUIT DI
23. reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications not expressly approved by lt manufacturer gt could void the user s authority to operate the equipment I 1164 Route 220 516A Elm Street St Elie d Orford Qu bec Canada Manchester NH 03101 JOB 2S0 USA Table of contents SAFETY PRECAUTIONS 2 BEFORE USING YOUR REMOTE STARTER 2 THE REMOTE CONTROL 3 USING YOUR REMOTE CONTROL 3 BATTERY REPLACEMENT 3 TABLE OF COMMANDS 4 START COMMANDS 5 SECURITY SYSTEM 8 LOCK UNLOCK COMMANDS AND ALARM SYSTEM ARMING DISARMING 13 OTHER COMMANDS 14 SAFETY
24. ress the ef button doors are unlocked and alarm is disarmed parking lights flash and siren chirps twice to confirm command has been received and that no alarm condition was generated during your absence If there was a violation confirmation is different 4 flashes or chirps to warn you See table of alarm codes to know which zone generated alarm condition The Unlock function can be programmed and connected in such a way that the first Unlock command only unlocks the driver s door while a following Unlock command unlocks the other door s Dome light will turn on for 30 seconds every time Unlock command is sent not applicable in semi passive mode and only if option is hookup This 30 second duration is cancelled when Lock command or Trunk command is sent brakes are applied or key is inserted in ignition and turned to ON position 13 TRUNK RELEASE R Press m button Trunk is released and parking lights flash three times to confirm command has been received Trunk cannot be released if ignition key is in ON position Furthermore if alarm is armed and system is not equipped with an additional sensor capable of detecting trunk release optional equipment not included opening of trunk with remote control will not be possible In this case parking lights flash once to confirm that command has been received but trunk could not be released If you are not sure you have received confirmation repeat command System will repeat c
25. s below Code Protection Zone Priority 1 System is armed 8 A door is was open Hood is was open Alarm condition is was detected on shock sensor input Key is was in ignition position IGN Alarm condition is was detected on additional sensor input Additional sensor monitors status of Loss of power 12V battery supply was removed co 1 o h 16 o moo More than 3 warnings were given within 3 minutes by pre shock input SAFETY CHECKS In order to maintain a high safety standard proceed with the following checks every month HOOD SWITCH Remote start your vehicle e Open hood Engine should stop as soon as hood is opened If engine does not stop immediately turn main switch to OFF position and leave it off until situation is rectified Contact your service center GEARSHIFT CHECK If key must be in ignition for gearshift to be moved out of P your vehicle is safe as long as keys are kept away from children If on the other hand gearshift can be put in gear without key being in ignition proceed with this simple check Put gearshift in gear Remain in the vehicle and be ready to apply brakes Start vehicle with remote starter Repeat these steps with gearshift in every position other than Park and Neutral If starter reacts within 90 seconds which would not be safe turn main switch to OFF position and leave it off until sit
26. uation is rectified Contact your service center e With gearshift in P start vehicle with remote starter Remain in vehicle and be ready to apply brakes e Without applying brakes move gearshift out of P If without applying brakes engine does not stop immediately which would not be safe turn main switch to OFF position and leave it off until situation is rectified Contact your service center REPLACING OR BOOSTING VEHICLE BATTERY If you have to replace or boost your battery for any reason turn main switch to OFF position and leave it OFF until battery is replaced or fully charged Reversing polarity when boosting your battery could permanently damage your remote starter Note If alarm is armed when battery is disconnected siren will sound when battery is reconnected if a zone is in violation To avoid this put system in Valet Mode before disconnecting battery Note
Download Pdf Manuals
Related Search