K6 Camera User`s manual
Contents
1. 60 It is to adjust monitor window saturation The value ranges from 0 to 100 The default value is 50 The larger the number the strong the color is This value has no effect on the general brightness of the whole video The video color may become too strong if the value is too high For the grey part of the video the distortion may occur if the white balance is not accurate Please note the video may not be attractive if the value is too low The recommended value ranges from 40 to 60 The value here is to adjust the edge of the video The value ranges from 0 to 100 The larger the value is the clear the edge is and vice versa Please note there is noise if the value here is too high The default value is 50 and the recommended value ranges from 40 to 60 It is to reduce video noise The larger the number is the lower the noise is The details of the video may disappear if the value here is too large Anti flicker e Outdoor In this mode you can switch exposure mode to get the effect under the corresponding exposure mode e 50Hz When the current is 50Hz system can auto adjust the exposure according to the environment brightness in case there is any strip 60Hz When the current is 60Hz system can auto adjust the exposure according to the environment brightness in case there is any strip Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component2. Name Pb Hg Cd Cr VI PBB PBDE Circuit Board A 5 o s 2 a Component Device Construction o o o o o o Material Wire and Cable O o o o o o Packing A 7 E o A Components Accessories o o o o o o O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T 11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T1 1363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e All trademarks and registered trademarks mentioned are the properties of their respective owners e If there is any uncertainty or controversy please refer to the final explanation of US e Please visit our website or c
3. Use direction buttons to set position and zone size Default Return amp Exit Language EN COM al Address 1 254 Setup Apply Return amp Exit System lt Version XXXXXXXXX Info Return amp Exit Image Sharpness 0 100 Brightness 0 100 Contrastne 0 100 ss Saturation 0 100 Sharp 0 100 Suppress Chroma 0 100 suppress Gamma 0 5 Video 1080P 25 OK CANCEL Format 1 1080PQ 30 720P G25 l 720 PG30 l 72 op s0e 7 20P 60 Return amp Exi t Reset Exit 4 2 Note Parameter Function Brightness Saturation It is to adjust monitor window bright The value ranges from 0 to 100 The default value is 50 The larger the number is the bright the video is When you input the value here the bright section and the dark section of the video will be adjusted accordingly You can use this function when the whole video is too dark or too bright Please note the video may become hazy if the value is too high The recommended value ranges from 40 to 60 It is to adjust monitor window contrast The value ranges from 0 to 100 The default value is 50 The larger the number is the higher the contrast is You can use this function when the whole video bright is OK but the contrast is not proper Please note the video may become hazy if the value is too low If this value is too high the dark section may lack brightness while the bright section may over exposure The recommended value ranges from 40 to
4. 4000 1 2000 1 1000 1 500 1 250 1 120 1 100 1 60 1 50 1 30 1 25 1 15 1 12 1 10 1 8 1 6 1 5 1 4 1 3 Customized Gain Max 0 100 Gain Min 0 100 Return amp Exit Exp Level 0 14 Exp Speed 0 7 Anti flicker Outoodr 50H e 50HZ 1 50 1 100 1 25 Z 60HZ 1 10 1 5 1 4 e 60HZ 1 60 1 120 1 30 1 4 1 12 1 6 The 50HZ and 60HZ mode have different manual exposure mode and there is no low motion blur and low noise exposure mode BLC Si BLC OFF ON WDR 0 100 HLC 0 100 The HLC is valid when auto exposure and outdoor anti flicker mode are both valid Return amp Exit White Auto Balance Manual Blue 1 100 Red 1 100 Return amp Ex it Day Night Day Night Auto B W Color Function 2DNR 0 100 3DNR 0 100 D Zoom 1 10 Lens Manual DC Return amp Ex it Advanced a CAM A Mirror Flip Mirror OFF ON Flip OFF ON Return amp Exit Motion OFF Detect ON ql Area Sel 0 3 There are four motion detect zones ranging from 0 to 3 You need to set parameters for each zone Area State OFF ON Sensitivity 0 100 Threshold 0 100 ArearSetup Positione Size Use direction buttons to set position and zone size Default Return amp Exit Privacy OFF Mask ON J Area Sel 0 7 There are eight privacy mask zones ranging from 0 to 7 You need to set parameters for each zone Area state OFF ON Area setup Position Size
5. HD Analog Camera User s Manual Version 1 0 0 1 Table of Contents General Introduction 1 1 Overview 1 2 Features 1 3 Functions 1 4 Specifications Framework 2 1 DIMENSIONS Jaa rene ed eee Sd Dot oe Welcome Thank you for purchasing our analog camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference 11 Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC in the IEC60950 1 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended If this product is installed in the ceiling please make sure the installation position can sustain the min 50N 4 Qualified engineers needed All the e
6. alog HD camera conforms to the HDAVS standard It supports video signal high speed long distance transmission without any delay It can be controlled by the DVR conforming to the HDAVS 1 2 Features e High performance CMOS image sensor megapixel definition e HD video coaxial cable to transmit the control signal e Support 75 3 coaxial cable transmission without any loss Transmission distance is over 300m Support analog HD and standard definition switch Support 1080P 25 1080P 30 720P 25 720P 30 720P 50 720P 60 High speed long distance real time transmission Support OSD on screen display suitable for user self defined setup Support privacy mask image digital zoom Support DC12V power supplying Support 3D noise reduction denoise excellent performance in low illumination environment IP66 compliance Support ICR switch to realize surveillance both in the daytime and at night e Support intelligent IR function 1 3 Functions HDAVS Specification HDAVS is an over coaxial cable analog HD video transmission standard The technology renders two HD video formats by progressive scanning OSD User friendly on screen display for you to select the different functions ICR The IR cut removal is to filter the IR light in the daytime and then auto switch to the general fitter at night This function allows the camera to output the high sensitivity and clear video Smart IR technology The sensor controls the IR light
7. device installation pedestal to the proper position and then line up the three screw holes in the device pedestal to the three plastic expansion bolt holes in the installation position Put the three self tapping screws in the three plastic expansion bolts firmly Loosen the M3X8 cross recessed pan head slot screw of the pedestal to unfasten the preforming Do not remove loosen a little bit will be OK Adjust the lens to the proper monitor angle and then use the original preforming to turn the M3X8 cross recessed pan head slot screw back Steps Line up the three spigots of the decoration ring to the jags from the bottom to the top and then turn clockwise until you hear a clear sound KA Now the installation is complete Ceiling or Wall Expansion Bolt Pi ry E a 3 Installation Pedestal M3X18 Cross Recessed Pan Head l r TL ST3X18 Self tapping Screw Screw and Preforming i Gland Cover Decoration Ring Dome Body Figure 3 1 4 Menu 4 1 Menu List Exposure Exposure Auto Mode Low Gain Max 0 100 Noise Gain Min 0 100 Return amp Exit For the 2 and the 3 menu when you click Exit button to exit system saves current setup by default Low Motion Shutter Max e PAL 0ms 40ms Blur J e NTSC 0ms 33ms Shutter Min e PAL 0ms 40ms e NTSC 0ms 33ms Return amp Exit Shutter 1 100000 1 10000 Manuals 1
8. less than 95 no condensation Humidit Power Consumption 3 5W MAX Input 12V 0 29A Over 300m via 75 3 coaxial cable a Weight 300g Installation Mode Wall mount In ceiling mount 2 Framework 2 1 Dimensions Please refer to the following figures for the dimension information The unit is mm See Figure 2 1 Lens 113 6 Dome Body Dome Decoration Ring Video _ NG Power gt Standard Definition art High Definition Switch Control Cable Figure 2 1 When the standard definition high definition switch control cable is short circuit system outputs standard definition video Otherwise when the circuit is open system outputs the high definition video 3 Installation Important e Before the installation please make sure the installation surface can sustain at least 3X weight of the bracket and the camera Please follow the steps listed below See Figure 3 1 Step 1 Turn clockwise to remove the decoration ring from the snap joints Step 2 Please take the installation position map in the accessories bag and then paste it on the ceiling or the wall according to your monitor area requirements Step 3 Draw and then dig three plastic expansion bolts holes in the installation surface and then insert three expansion bolts in the holes Secure these three bolts firmly Please draw the cable out from the cable exit when you install the device Step4 Adjust the
9. on off via the combination work of the hardware and software which realizes the automatically IR light compensation according to the environment illumination 1 4 Specifications Please refer to the following sheet for specification 2 Megapixel HDAVS Analog Camera Parameter AVS D2210 Video Format PAL NTSC Effective Pixel 1920 H 1080 V Electronic Shutter Support slow shutter 1 3s 1 100 000s Video Standard HDAVS CVBS compliance Video Frame Rate 1920x1080 25fps 1920x1080 30fps 1280x720 25 fps 1280x720 30 fps 1280x720 50 fps 1280x720 60 fps Lens Port M12 Lens Type 3 6mm Day Night Switch ICR mechanical auto switch Video Output 1 channel HDAVS analog high definition video output CVBS analog standard definition video output Can switch Denoise Noise Reduction Support 2D 3D denoise OSD Menu Control Support l EXPOSURE Exposure Mode Exposure Level Exposure Speed Anti Flicker BLC Return WHITE BALANCE Auto Manual Day Night Return amp Exit DAY NIGHT Auto B amp W Color Return amp Exit FUNCTION 2DNR 3DNR D zoom Lens Return amp Exit Cam Title Mirror amp Flip Motion Detect Privacy Mask Language COM ADVANGER Setup System Info Return amp Exit Sharpness Brightness Contrastness Saturation Sharp Suppress Chroma Suppress Gamma Video Format Return amp Exit Max IR Distance Transmission Distance Protection Level IP66 Working Temperature 30 C 60 C Humidity is
10. ontact your local service engineer for more information
11. xamination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series analog camera should be installed in a cool dry place away from direct sunlight or strong light inflammable explosive substances and etc The working temperature ranges from 30 C to 60 C Please keep it away from the electromagnetic radiation object and environment Please make sure the CMOS component is out of the radiation of the laser beam device Otherwise it may result in CMOS optical component damage Please keep the sound ventilation Do not allow the water and other liquid falling into the camera 6 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package 7 Daily Maintenance 111 Please shut down the device and then unplug the power cable before you begin daily maintenance work Use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CMOS component when you do not use the camera iv 1 General Introduction 1 1 Overview This series megapixel an
Download Pdf Manuals
Related Search