Luckystar 5mvp3_v4
Contents
1. MVP3 Main Board 29 AGP Accelerated Graphic Port is the new bus standard that allows the bus speed to run at 66 MHz with up to 133 MHz data transfer capabilities which is four times as fast as that of the PCI bus At this speed the AGP graphic cards can transfer data up to 528MB second This high transfer capabilities enables 3D graphic applications multiple media applications uncompressed to run smoothly and display in broadcasting quality There are three PCI slots on board 133MB s data transfer rate on PCI bus can be compared to 33MB s on EISA bus or 8MB s on ISA bus Synchronize Operation CPU to PCI interface for good graphic performance There are 3 standard 32 bit ISA slots on board All of them are bus mastering MVP3 Main Board 30 2 6 DIMM Memory Installation SMVP3 has 3 DIMMs on board Either DIMM 1 DIMM2 or DIMM3 supports 8 MB 16 MB 32 MB 64 MB and 128MB Maximum memory for SDRAM is up to 384MB EDO RAM is up to 768 MB This main board also supports asynchronous operation for CPU and DIMM data transfer Set DIP switch S1 Pin 7 when the system is under asynchronous operation DIMM3 DIMM2 DIMM MVP3 Main Board 31 Insert the module as shown Due to differe2. Chapter3 BIOS Setup 33 Award BIOS CMOS Setup 33 Standard CMOS Setup 34 BIOS Features Setup 36 Chipset Features Setup 40 Power Management Setup 42 PNP PCI Configuration Setup 45 Integrated Peripherals 47 Supervisor ser Password 50 IDE HDD Auto Detection 53 Load Setup Defaults 56 Save and Exit Setup 57 Quit Without Saving 58 Chapter4 Appendix 59 Memory Map 59 I O Map 60 Time amp DMA Channels Map 61 Interrupt Map 62 RTC amp CMOS RAM Map 63 Award BIOS Hard Disk Type 64 ISA I O Address Map 66 Chapter5 Q amp A 68 Error Messages During Power On Self Test 68 Frequently Asked Questions 70 MVP3 Main Board I Chapter 1 Introduction 1 1 Main Board Overview The main board is a new generation AGP Pentium main board with high performance in rendering and texture for 3D Graphics Based on Apollo MVP3 chipset the main board has intergrated the latest advances in processor memory I O technologies into an AT form factor It is also designed for the upcoming 100 MHz F S B CPUs like AMD K6 2 K6 3 series or Cyrix MII CPUs The main board utilizes VIA Apollo MVP3 and supports new architects such as high speed AGP graphic port SDRAM Ultra DMA 33 bus master IDE and USB port It has three Dual In line Memory Modules DIMM which can be installed with SDRAM memory The memory subsystem supports up to 512Mbyte SDRAM of non buffered 3 3V using standard 168 pin DIMM sockets The main board implements high performance I O Contro
3. I i III t I N N H U Main Board 64 5MVP3 ied ma eed P bal el Pre comp Zone 32 925 9 65535 926 72MB 33 89MB 34 106MB 35 115MB 36 124MB 40 80 6 65535 80 17 42MB 42 104 8 65535 1023 17 68MB 43 800 6 65535 852 17 44 800 9 65535 852 17 64MB 45 76 8 6555 775 17 104MB 46 0 j 6 47 users TYPE 1 O MVP3 Main Board 65 5MVP3 4 7 ISA Address Map VO Mies EN 000 O1F 020 03F 040 OSF 060 06F 070 O7F 080 OOF 0A0 OBF ODF OFO OFF 1F8 200 207 20C 20D 21F 278 27F 2B0 2DF 2 1 2E2 2E3 2F8 2FF 300 31F 360 363 364 367 368 36B 36C 36F 378 37F 380 38F 390 393 3A0 3AF DMA Controller 1 8237A 5 Interrupt Controller 1 8259A System Timer 8254 2 8742 Keyboard Controller real time Clock CMOS and NMI Mask DMA Page Register 74LS612 Interrupt Controller 2 8259A DMA Controller 2 8237A 5 1486 Math Coprocessor Fixed Disk Drive Adapter Game I O Reserved Reserved Parallel Printer Port 2 Alternate Enhanced Graphic Adapter GPIB Adapter 0 Data Acquisition Adapter 0 Serial Port 2 RS 232 C Prototype Card PC Network Low Address Reserved PC Network High Address Reserved Parallel Printer Port 1 SDLC Bisynchronous 2 Cluster Bisynchronous 1 3B
4. BIOS ZASLELTH CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HOD AUTO DETECTION PMP PCI CONF IGUBA Esc Quit Tire Select tem FtG Save Exit Setup Shift FZ Change Calar Load Setup Defaults loads optimized settings which are stored in the BIOS ROM The auto configured settings only affect BIOS Features Setup and Chipset Features Setup screens There is no effect on the standard CMOS setup To use this feature highlight it on the main screen and press the lt Enter gt key A line will appear on screen asking if you want to load the setup default values Press the lt Y gt key and then press the lt Enter gt key The setup defaults will then load Press lt N gt if you don t want to MVP3 Main Board 56 5MVP3 3 11 Save amp Exit Setup The Save amp Exit Setup option will bring you back to boot up procedure with all the changes you have made which are recorded in the CMOS RAM ROM PCI 13A BIOS 2ASLELTB CMIY SETUP UTILITY AWARD SOFTWARE IMC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USEH PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION CONF IGURA SUE 12 amd ESIT te LOAD SETUP DEFAU Esc Quit 1 Select Item F18 Save Exit Setup S
5. 01 second alarm 02 minutes 03 minutes alarm 04 hours 05 hours alarm 06 day of week 07 of month 08 month 09 year Oa status register a Ob status register b Oc status register c Od status register d Oe diagnostic status byte Of shutdown byte 10 floppy disk drive type byte 12 hard disk type byte 13 reserve 14 equipment type 15 base memory low byte 16 base memory high byte 17 extension memory low byte 18 extension memory high byte 19 2d 2e 2f 30 Reserved for extension memory low byte 3 reserved for extension memory high byte 32 date century byte 33 information flag 34 3f reserve 40 7f reserved for chipset setting data MVP3 Main Board 63 5MVP3 4 6 Award BIOS Hard Disk Type m comp Zone 128 305 17 10MB 300 615 17 512 940 17 6 6 52 17 4 A 65835 1 TIME 8 256 su 17 m sms 9 900 15 65535 901 17 117MB 13 306 8 128 39 17 21MB 14 73 7 65535 733 17 44MB 161 s I 4 o 17 21 977 300 17 42MB st sm 7 ess om in mn S mi 7 si om GMB 733 300 732 17 7 I 300 732 17 AB 733 0 733 306 336 ru m 5 0 s Low 25 1004 9 65535 95 17 28 1224 15 65535 69 17 159 29 1004 8 65535 823 17
6. Secondary Slave UDMA Disabled the 4 items IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA and IDE Secondary Slave UDMA will not be available MVP3 Main Board 47 5MVP3 IDE Primary Master PIO IDE Primary Slave PIO This feature detects your primary master hard disk device Auto default Mode 0 1 2 3 4 IDE Secondary Master PIO IDE Secondary Slave PIO This feature detects your secondary master hard disk device Auto default Mode 0 1 2 3 4 Onboard FDC Controller Enabled default Disabled Onboard Serial Port 1 3F8 IRQ4 default 2F8 IRQ3 3ES IRQ4 Auto Disabled Onboard Serial Port 2 3F8 IRQ4 2F8 IRQ3 default 3ES IRQ4 Auto Disabled MVP3 Main Board 48 5MVP3 IR Address Select Disabled Select Disabled to disable IR function default 3F8H IR Mode HP SIR ASKIR IRQ Mode IRQ10 IRQ11 IRQ3 IRQ4 2F8H IR Mode HP SIR ASKIR IRQ Mode IRQ10 IRQ11 IRQ3 IRQ4 3E8H IR Mode HP SIR ASKIR IRQ Mode IRQ10 IRQ11 IRQ3 IRQ4 2E8H IR Mode HP SIR ASKIR IRQ Mode IRQ10 IRQ11 IRQ3 IRQ4 Onboard Parallel Port 378 IRQ7 default 3BC IRQ7 278H IRQ5 Disabled Parallel Port Mode SPP Default EPP ECP Choosing this item there is another line shown ECP Mode Use DMA 3 default 1 ECP EPP Choosing this item ano
7. I IDE reset Pin2 Ground Pin3 Data 7 4 Data 8 Pin5 Data 6 Pin6 Data 9 Pin7 Data 5 Pin 8 Data 10 Pin9 Data 4 Pin 10 Data 11 Pin 11 Data 3 Pin 12 Data 12 Pin 13 Data 2 Pin 14 Data 13 Pin 15 Data 1 Pin 16 Data 14 Pin 17 Data 0 Pin 18 Data 15 Pin 19 Ground Pin 20 Key NC Pin 21 PDREQ Pin 22 Ground Pin 23 write Pin 24 Ground Pin 25 read Pin 26 Ground Pin 27 INC Pin 28 ALE Pin 29 INC Pin 30 Ground Pin 31 IDE IRQ 14 Pin 32 IOSC15 Pin 33 Address Al Pin 34 NC Pin 35 Address AO Pin 36 Address A2 Pin 37 chip select 0 Pin 38 IDE chip select I Pin 39 IDE active Pin 40 Ground MVP3 Main Board 21 2 4 9 LAN Wake up on LAN marked as LAN is a 3 pin connector To support this feature a network card is required for the system More than that a network management software must be installed too WOL Wake up on LAN Wake LAN function requirement Power should offer at least 750mA to the signal SV trickle voltage to support WOL function MVP3 Main Board 28 2 5 Expansion Slots Expansion slots contain one A G P slot three PCI slots and three ISA slots on this main board Below are details Expansion Sots PCI Slots
8. UGA H 18914 Hard Disk Primary LPT amp CUM 5 Reserved Disahled HDD FID i P master Quit tie Jelect Item Madem Bing Hesume Disabled Help PU PD Madify ETC Alarm Besume Disabled HId Values Shift FZ Calar Laad Setup Defaults ACPI function Disabled default Enabled Power Management User Define default users can configure their own power management Min Saving Max Saving Disabled MVP3 Main Board 42 5MVP3 PM Control By APM No system BIOS will ignore APM Yes default system BIOS will wait for APM s prompt before it enter any PM mode e g Doze standby or suspend Note 1 if APM is installed and there is a task running even if the timer is time out the APM will not prompt the BIOS to put the system into any power saving mode Note2 If APM is not installed this option has effect Video Off Method DPMS default Blank Screen V H Sync Blank MODEM Use IRQ 3 default 4 5 7 9 10 11 NA Soft Off by PWRBTN Instant off Delay 4 sec This allows the user to set the soft off power button to turn off the system or set to 4 seconds holding the power and system will shut down in 4 seconds HDD Power Down Disabled default 1 min 15 min Doze Mode Disabled default 1 min 1 hour Suspend mode Disabled default 1 min 1 hour MVP3 Main Board 43 5MVP3 Modem Ring Resume Enabled modem ring on fun
9. supported by LBA mode is 8 4 GB which is obtained by the following formula No Cylinder 1024 X No Head 255 X Sector 63 X Bytes Per Sector 512 8 4 GB MVP3 Main Board 54 5MVP3 3 Large Mode Extended HDD access mode supported by Award software Some IDE HDDs contain more than 1024 cylinder without LBA support in some cases user do not want LBA The Award amp BIOS provides another alternative to support these kinds of large mode Cyls Head Sector Mode 1120 16 59 NORMAL 560 32 59 LARGE BIOS tricks DOS or other OS that the number of cylinders is less than 1024 by dividing it by 2 At the same time the number of heads is multiplied by 2 A reverse transformation process will be made inside int 12h in order to access the right HDD address the right HDD address 4 Maximum HDD Size No Cylinder 1024 X No Head 32 X No Sector 63 X No Bytes Per Sector 512 1 GB To support LBA or large mode of HDDs there must be some softwares involved All these softwares are located in the Award HDD service routine int 13h It may be failed to access a HDD with LBA large mode selected if you are running under an perating system which replaces the whole int 13h Unix operating systems do not support either LBA or large and must utility the standard mode Unix can support drives larger than 528MB MVP3 Main Board 55 5MVP3 3 10 Load Setup Defaults BOM
10. to close and back to open the system will enter sleep mode immediately This function is to make sure power saving is working well In PC system it is used to connect to the push button SMI switch located on the case front panel if there is The system can be forced to power saving mode by pressing the SMI switch SMI Operation Open Normal Close System will enter sleep mode TB LED with a 2 pin Berg strip on case front panel indicates the current speed status of system It is used to connect to the Turbo Led on the front panel of the case if there is Reset connector is a 2 pin keyed Berg strip connected to the push button reset switch on the case s front panel Shorting both pin 1 amp pin 2 can reset the system which is similar to the power off and then on again Pin Operation Open Normal Close Hardware reset SPEAKER connector is 4 keyed Berg strip It is used to connect to the case speaker to the main board for sound purpose KEYLOCK is a 2 pin connector It is used to connect the key lock on the case front panel if there is Keyboard may be disconnected with the system through this function Pin Operation Open Normal Close Short the connector to be disconnected with the system POWER LED is a 3 pin connector It is used to connect to the LED on the case front panel The LED shows the status of the power MVP3 Main Board 17 2 4 2 Ba
11. 2 Amperes 3 3V 5 3 Amperes 12V 10 800 mA 5V 5 150 mA 12V 5 100 mA ME WOL Wake up on LAN function Power supply should offer at least 750mA to the signal SV trickle voltage to support e Power supply regulation Onboard switching voltage that support appropriate power to the CPU and future upgraded CPUs e Special features Wake up on LAN Modem ring on Windows 95 power off Auto detection of CPU voltage temperature and fan speed MVP3 Main Board 4 1 3 Notice of Hardware Installation Before hardware installation make sure you have checked the following things A Check the package If any of these items is missing or damaged contact the dealer from whom you purchase Leave this main board in its original package until you are ready to install it In the package there are the main board manual cables driver amp utility CD B Make sure power is off C Avoid ESD Electrical Static Discharge While working with this main board wear a grounded wristband or ankle strap to avoid ESD Electrical Static Discharge MVP3 Main Board 5 MVP3 Main Board Chapter 2 Installation 2 1 Layout Reference USB 5 we BIOS H MOU
12. Cacheahle Enabled Current Uini U System BIOS CacheahIe Enabled Memary Hale frt t5rm ddr Disabled PCI Dynamic Bursting Enabled PCI Master WS Write Enabled PCI Master Bead Prefetch Enabled PCI 2 Access 1 Betry Disabled AGP Aperture Size 128M Quit fl Select Item AGP ZX Made Disable Help PU PD Modify HId Values Shift FZ Calar Laad Setup Defaults Bank 0 1 2 3 4 5 DRAM Timing This will determine the timing of SDRAM The user can separately adjust the timing of bank 0 1 2 3 4 5 FP EDO 70ns default FP EDO 70ns Normal Medium Fast Turbo SDRAM Cycle Length control the DRAM page missing and row miss leadoff timing 2 3 default Video BIOS Cacheable Enabled Default Disabled MVP3 Main Board 40 5MVP3 Memory Hole at 15Mb Addr this field enable a memory hole in main memory space CPU cycles matching an enabled hole are passed on to PCI bus Disabled default 15M 16M AGP Aperture Size To select the size of the Accelerated Graphics Port AGP aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation 128M default 64M 32M 16M 8M 4M OnCHip USB Enabled default Enabling this function adds the function of USB Keyboard Support Disabled USB Keyboard Support Disabled default Enabled enable this function whe
13. Enable default Disable Assign IRQ for VGA Enable default Disable MVP3 Main Board 46 5MVP3 3 7 Integrated Peripherals PCI IS BIOS CZRGLELTB INTEGRATED PERTPHERALS AWAED JOFTWARE INC OnChip IDE First Chanel Onboard FDC Camtraller Enabled OnChip IDE 3ecand Channel Enabled Onhaard Serial Port 1 1 4 IDE Prefetch Mode Enahled Serial Part 2 IDE HDD Black Mode Enchied IB fiddress Select Disable IDE Primary Master PIO IDE Frimary Slave PIU Secondary Moster PIU futa Onboard Parallel Port 1 q7H IBQ7 IDE Secondary Slave FIO Parallel Part Mode SPP IDE Primary Master UDMA IDE Primary Slave UDMA Auta Jecandary Master UDMA futa IDE Secondary Slave UDMA fiuta Init Display First AGP Quit Select Item Help PU PD Modify 014 Values Shift FZ Calar Load Setup Defaults OnChip IDE First Channel I Enabled default it allows to adjust the items IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA and IDE Primary Slave UDMA Disabled the items IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA and IDE Primary Slave UDMA will not be available OnChip IDE Second Channel 1 Enabled default it allows to adjust the 4 items IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA and IDE
14. F Monochrome Display and Printer Adapter MVP3 Main Board 66 5MVP3 VO dis 3CF Enhanced Graphics Adapter 3D0 3DF Color Graphics Monitor Adapter 3F0 3F7 Diskette Drive Controller 3F8 3FF Serial Port 1 RS 232 C 6E2 6E3 Data Acquisition Adapter 1 790 793 Cluster Adapter 1 AE2 AE3 Data Acquisition Adapter 2 B90 B93 Cluster Adapter 2 EE2 EE3 Data Acquisition Adapter 3 1390 1393 Cluster Adapter 3 22E1 GPIB Adapter 1 2390 2393 Cluster Adapter 4 42F 1 GPIB Adapter 2 62 1 GPIB Adapter 3 82 1 GPIB Adapter 4 A2EI GPIB Adapter 5 C2EI GPIB Adapter 6 E2EI GPIB Adapter 7 MVP3 Main Board 67 5MVP3 Chapter 5 Q amp A 5 Errors Messages During Power On Self Test During power on self test post BIOS will automatically detect the system devices Below is the questions that users may always meet The user may press Esc key to skip the full memory test 1 Beep sound On power on the system make beep sound to offer different messages If the system is configured correctly it prompts a short beep to show correct the devices configuration is done correctly When VGA card and DIMM modules are not plugged well the system makes longer and constant beep sounds BIOS ROM checksum error It indicates the checksum of the BIOS code is not right and system will always halt on power on screen Contact the dealer to exchange a new BIOS CMOS battery fails It indicates the CMO
15. PCIZIS PnP fissign IB For USB Enabled IBQ t2 assigned ta PCI ISA PnP fissign Fur VGA Enabled IBQ t4 assigned ta PCIZIS PnP assigned ta PCI IS PnP assigned ta PCIVISA PnP assigned PCI IS PnP Quit Select Item assigned PnP Helg PU PD Modify assigned PCI IS PnP Values Shift FZ Calar assigned PCI IS PnP Load Setup Defaults assigned PCI IS PnP PNP OS Installed No default OS will not recognize PnP devices Yes OS will arrange the setup of PnP devices Resources Controlled By Manual default The table will show the below items Reset Configuration Data IRQ 3 assigned to DMA 0 assigned to The user can adjust the shown items as required Auto The table will not show the above items and the system will automatically assign the above setup MVP3 Main Board 45 5MVP3 Reset Configuration Data Disabled default Enabled to reset Extended System Configuration Data ESCD when you exit setup if you have installed a new add on card and the system reconfiguration has caused such a serious conflict that the operating system can not boot up IRQ 3 Assigned To IRQ 15 Assigned To PCI ISA PnP default Legacy ISA DMA 0 Assigned To DMA 7 Assigned To PnP default Legancy ISA PCI IRQ Actived By There are 2 modes in activating PCI IRQ Edge Level default Assign IRQ for USB
16. Pin9 GND 10 FDD Motor A enable Pin 11 GND 12 FDD Drive B enable Pin 13 GND 14 FDD drive A enable Pin 15 GND 16 FDD Motor enable Pin 17 GND 18 FDC head direction Pin 19 GND 20 FDC step pulse output to the drive during a SEEK operation Pin21 GND 22 FDC write enable serial data to the Drive Pin 23 GND 24 FDC write enable identify Pin25 GND 26 Floppy disk track 0 Indicates that the head of the selected drive is on track zero Pin 27 GND 28 FDD write protect Indicates that the disk of the selected drive is write protected Pin 29 GND 30 Read disk data serial data input input from the FDD Pin31 GND 32 Floppy disk side 1 select Pin 33 GND 34 Floppy disk change This is an input pin that senses whether the drive door has been opened or a diskette has been changed MVP3 Main Board 26 2 4 8 IDE 1 and IDE2 IDE 1 IDE 2 both have 40 pins There are 2 IDE connectors supported on this system board is primary channel and IDE2 is secondary channel Each channel supports 2 IDE devices and 4 channels in total for this main board IDE2 2 40 00000000000000000000 00000000000000000000 1 39 2 IDEI 40 00000000000000000000 00000000000000000000 1 39 Pin Signal Pin Signal Pin
17. S pressen er I O 6 fe ej COMI LAN IR 4 ev 6 ies 513 SLP SLI PCI PCII o o setae IDE AGP zzz lt lt sz lt lt lt v N T82C598M VP FAN2 JP4 o d o 00 a a NE S2 oe 57 299 9000000000000000000000 Sy EANI 0 MVP3 Main Board 7 2 2 Quick Reference to CPU Speed Setup The setup of CPU speed is simplied to a DIP switch form which is only related to jumpers S1 and S2 This design is also convenient to recognize those jumpers as below S2 CPU voltage selector NO Main Board 8 Intel Pentium PU SYS S Clock Clock Voltage P54C 100 MHZ off off off 54C 120 MHZ off 54C 133 MHZ off off on on off on off 55 166 MHZ 66 MHZ 2 8 33V 25X on on off 54 180 MHZ 60 MHZ 33V 3X off on off 54 200 MHZ 66 MHZ 33V off on off 55 200 MHZ 66 MHZ 2 8 3 3V 3X off on off 255 233 MHZ 66 MHZ 2 8 3 3V 3 5X off off ofr off on on off off off on Cyrix CPU Clock SYS Ratio S2 Clock oas 3 T2 L5 DS E i50 M1 60 MHz 352V 2X on o
18. S battery does not work Contact the dealer to exchange anew BIOS CMOS checksum error It indicates the CMOS checksum is incorrect Load the default values in BIOS to solve this problem This error may result from a weak BIOS so exchange a new BIOS if necessary Hard disk initialize Please wait a moment Some hard drives require more time to initialize MVP3 Main Board 68 5MVP3 6 Hard disk install failure The system can not find or initialize the hard drive controller or the drive Check if the controller is set correctly If no hard disk is installed Hard drive selection must be set to none 7 Keyboard error or no keyboard present This means the system can not initialize the keyboard Check if the keyboard is plugged well and be sure no keys are pressed during POST 8 Keyboard is lock out Unlock the key Normally when this message comes out check if there is anything mis placed on the keyboard Be sure nothing touches the keys 9 Memory test fails There will be more information to specify the type and location of the memory error 10 Primary master hard disk fail The BIOS find an error in the primary master hard disk drive 11 Primary slave hard disk fail The BIOS finds an error in the primary slave hard disk drive 12 Secondary master hard disk fail The BIOS finds an error in the secondary slave master hard disk drive 13 Secondary slave hard disk fail The BIOS finds an err
19. SMVP3 Ver 4 0 AT Form Factor Main Board User s Manual Copyright Copyright 1998 by this company No part of this document may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means without prior written permission This manual and the information contained herein are protected by copyright All rights reserved Manual version 1 1 Published in 1998 Warning and disclaimer This manual 15 designed to provide information about the Pentium system board Every effort has been made to make this manual as accurate as possible but no warranty or fitness is implied All the information is provided on an as is basis The author and his corresponding publishing company shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this manual or from the use of the system board that accompanies it Information contained in this manual is subject to change without notice The manufacturer of the main board will not be held responsible for technical or editorial omissions made herein nor for the incidental or consequential damages resulting from its furnishing performance functionality or use Subsequent changes to this manual will be incorporated into the next edition We welcome any suggestion regarding this manual or our computer products Trademark
20. Soft Power On Momentary switch which connects on the front panel switch to the 2 pin SOFT PWR on the system board While the power switch on the back of ATX power is turned on the full power will not go into the system board until the front panel switch is momentarily pressed Push the switch again to turn off the power to the system board CNS ATX power connector mm C 5V 3 3V E 12V 3 3V A go Pin Signal Pin Signal Pin I 3 3V Pin2 3 3V Pin 3 3 3V 4 12 5 GND Pin6 GND Pin 7 5V Pin 8 SOFT PWR ON Pin 9 GND Pin 10 GND Pin 11 5V Pin 12 GND Pin 13 GND Pin 14 GND Pin 15 RAWPOWER Pin 16 5 Pin 17 5V Pin 18 5V Pin 19 12V Pin 20 5V MVP3 Main Board 22 2 4 4 CN7 AT Power Supply Connector ole ri E CN7 AT power connector Pin Signal Pin Signal 1 POWER GOOD 7 GROUND 2 5V DC 8 GROUND 3 12V DC 9 5V DC 4 12V 10 5V DC 5 GROUND 11 5V DC 6 GROUND 12 5V DC MVP3 Main Board 23 2 4 5 8 IR Connector IR connector suppo
21. ck Panel Connectors There COMI COM2 LPT USB and keyboard mouse on case back panel Please refer to more details as below COM1 COM2 The onboard serial port I and port 2 are the 9 pin D subminature male connector COM1 and COM2 COMI and COM2 can be disabled in BIOS setup Please refer to Chapter 3 Integrated Peripherals for more information COV Serial pat 2 COMI Serial part I 0 Ou a Pin Signal Pin Signal Pin 1 Carrier detect CD Pin 5 Signal ground Pin 2 Receive data Pin 6 Data set ready Pin 3 Transmit data TXD Pin 7 Request to send RTS Pin 4 Data therminal ready Pin 8 Clear to send CTS Pin 9 Ring indicator MVP3 Main Board 18 LPT Parallel Port The onboard parallel port is a 25 pin female connector marked as LPT LPT Parallel port 14 lew ETAT m 8 e CI oe oe oe e e oe ee ee Ce eres m G Pin Signal Pin Signal Pin 1 Strobe Pin 14 Auto feed Pin 2 Data bit 0 Pin 15 Error Pin 3 Data bit 1 Pin 16 Init Pin4 Data bit 2 Pin 17 SLCT in Pin5 Data bit 3 Pin 18 Gro
22. ction system can be turned on through modem Disable default disble this function Note this function only works when the system is turned off from Windows mode and Doze mode will not function RTC Alarm Resume auto power on at the appointed date and time Enabled key in the date of current month and time of the day System will turn on then Disable default disble this function ME Note this function only works when the system is turned off in Windows mode and Doze mode will not function Primary INTR on default Select on it adds the following functions 2 IRQ15 Reserved off Select off IRQ3 COM2 IRQ15 Reserved will not show MVP3 Main Board 44 5MVP3 3 6 PNP PCI Configuration Setup PCI IS BIOS Z SLEL1B CONFIGURATION AWARD SOFTWARE IMC PNP OS Installed CPU ta PCI Write Buffer Enabled Cantralled By Manual PCI Delay Transaction EnahIed Beset Configuratton Data Disabled AGP Master f VS Write Enabled AGP Master I WS Bead 3 assigned ta PCIVISA PnP 4 assigned PCIVISA PnP PCI IB fictived Bu Level 5 assigned ta PCIZIS PnP lat 1 Use IB Ma IEQ assigned ta PCIZIS PnP Slat Z Use Ma fiuta 0 9 assigned ta PCI ISA PnP Slat d Use IB Ma 180 19 assigned ta PCIVISA PnP IBQ tt assigned
23. ep 3 Set Security Option in BIOS Features Setup After setting password enter Security Option in BIOS Features Setup There are 2 options Setup amp System Setup secures CMOS setup System secures PC sytem and password is required during system boot up and CMOS setup MVP3 Main Board 51 5MVP3 2 How to Disable Supervisor Password amp User Password Step 1 Go to CMOS Setup Menu need to key in password first Step 2 Enter Supervisor Password or User Password After enter it shows Enter Password Press the Enter key instead of entering a new password when ENTER PASSWORD appears It will inform PASSWORD DISABLED PRESS ANY KEY TO CONTINUNE Pess any key as instructed to disable password PCL ISh BIOS ZASLELIC BIOS FERTERES SETIP SETI TAE BETECTTAM PASSWORD DISABLED PRESS ANY KEY TO CONTINUE Esc Quit Save Exit Sctep Ghift EZ Change Color MVP3 Main Board 52 5MVP3 3 9 IDE HDD Auto Detection PCIVISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE IMC HARD DISK TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Primary Slave Secondary Master Secondary Slave Select Primary Master Option N Skip N OPTIONS SIZE 5 HEAD PRECOMP LANDZ SECTOR MODE 2 Y 4302 523 255 0 8893 63 LBA 1 4303 8894 15 65535 8893 63 NORMAL 3 429 6555 2405 65535 8893 63 LARGE No
24. ff off on on on on on on on 16 66 MHZ 3 52v 2X on off off on on on on on on oxseL 150 60 MHZ 2 8 3 3V 2X on off off on on on off off off on 6 861 166 66 MHZ 2 8 53V 2X on off off off on on off off off on oxseL200 75 MHZ 2 8 3 3V 2X on off off on on off off off off on oxseMX 166 66 MHZ 2 9 3 3V 2X on off off on on on off off on on off on on on on off off on oX86MX 200 75 MHZ 2 9 3 3 2X on off on on off on off off on oX86MX 233 75 MHZ 2 9 3 3V 5X on on off on on off on off off on 6 86 266 83 MHZ 2 7 3 3V 5X on on off off on off on on on off 6 86 300 66 MHZ 2 9 3 3V AMD CPU Clock SYS CPU Ratio Clock Voltage off on 6 220 100 212 5 3 2 5 on on off off 6 2 266 66 MHZ 2 2 3 3V 4X on off on off on on 6 230 100 212 5 3 off on off 6 230 100 2 2 2 3 3V 5X off off off off K6240 100 7 2 2 3 3V 4X on off on off IK6 2450 100 7 24 3 3V 5X on on on off K6340 100 7 24 3 3V on off on off 5 5 5 5 MVP3 Main Board 9 2 3 J
25. ff 2 7V off off off on 2 8V on off off on 2 9V off off on on 3 2V on off on on 3 3V on on on on 3 5V MVP3 Main Board 12 2 3 3 JP4 DIMM Voltage Selector JP4 is a 4 pin connector to select either 3 3V or 5V DIMM voltage Select 1 2 3 4 for SV DIMM or 5 6 7 8 for 3 3V DIMM JP4 DIMM voltage selector 1 2 e o 00 z x 7 8 JP4 DIMM Voltage 1 2 3 4 5 5 6 7 8 3 3V MVP3 Main Board 13 2 3 4 JP5 Flash ROM Voltage Selector JP5 is a 3 pin connector to select SV or 12V flash ROM Select 1 2 for SV or 2 3 for 12V mm JP5 Flash ROM Voltage 1 2 5V 2 3 12V MVP3 Main Board JP5 Flash ROM voltage selector e Pint 0 9 14 2 3 5 JP7 CMOS Status clearing content of CMOS JP7 CMOS status Pind o JP7 is a 3 pin connector Clear CMOS if system password is forgotten Below is details to show how to clear CMOS JP4 CMOS Statu
26. flexibility efficiency and ease of use that meets a variety of price performance levels The main board is an ideal platform for the increasing requirements of today s and future s desktop application MVP3 Main Board 2 1 2 Specifications e PCB board size 25 cm x 22 cm e PCB layer 4 layers e ZIF Socket 7 Support Intel Pentium Cyrix 6x86 series MII series IDT WinChip series and AMD K5 K6 K6 2 K6 III CPUs M CPU is not enclosed in the package e Memory DIMM 3 of 168 pin 3 3V DIMM Professional PC 100 MHz freq PC 100 DIMM 66MHz DIMM be used with 100 MHz CPUs but the user must adjust jumper 81 pin 7 for asynchronous operation 66 MHz freq SDRAM up to 384MB EDO RAM up to 768MB 3 3V only Basic PC 66 MHz freq SDRAM up to 384MB EDO RAM up to 768MB 3 3V only e Expansion Slot 3x ISA slots 3x PCI slots and 1x A G P slot e Chipset VIA Apollo MVP3 VIA VT82C586B VIA VT82C598MVP e BIOS licenced Award full PnP Plug amp Play BIOS flash ROM BIOS e Cache 512K 1024K MVP3 Main Board 3 e T O function 2 x PCI IDE devices 1 x FDC 2 x serial ports 16550 fast com 1x parallel port device EPP ECP 2x USB connector IrDA infrared connector e Green function Complied with APM Advanced Power Management e AT form factor e Electrical Typical power supply Below is reference for ATX power supply Voltage Tolerance Current 5V 5 2
27. hbift FZ Change Calar MVP3 Main Board 57 5MVP3 3 12 Quit Without Saving ROM PCI I134 BIOS CZRGLELTB CMOS SETUP UTILITY SOFTWARE IMC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIUS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGUBA ak aii lat iasiauy LOAD SETUP DEFAUL Esc Quit Thee Select Item FtG Jave amp Exit Setun Shift FZ Change Calar The Quit Without Saving option will bring you back to normal boot up procedure without saving any data into CMOS RAM All of the old data in the CMOS will not be destroyed MVP3 Main Board 58 5MVP3 Chapter 4 Appendix 4 1 Memory Map Address range 00000 7FFFF 512K 80000 9FBFF 127K Extended conventional memory 9FC00 9FFFF Extended BIOS data area if PS 2 mouse is installed A0000 C7FFF 160K Available for hi DOS memory C8000 DFFFF Available for hi DOS memory and adapter ROMs E0000 EEFFF Available for UMB EF000 EFFFF 4K Video service routine for monochrome amp CGA adapter MVP3 Main Board 59 5MVP3 4 2 I O Map 000 01F DMA controller master 020 021 022 023 040 05F 060 06F 070 07F 080 09F 0 0 0 0 OF0 0FF 1F0 1FB 278 27F 2B0 2DF 2F8 2FF 360 36F 378 37F 3B0 3BF 3C0 3CF 3D0 CDF 3F0 3F7 3F8 3FF Interrupt controller master Chipset control registers I o posts Timer cont
28. ks while 720K 1 2M and 1 44M are all 80 tracks Default value is Disabled Boot Up Numlock Status On default Off Gate A20 Option Normal default Fast MVP3 Main Board 37 5MVP3 Typematic Rate Setting This determines the typematic rate Enabled enable typematic rate and typematic delay programming Disabled default disable typematic rate and typematic delay programming The system bios will use default value of this 2 items and the default is controlled by keyboard Typematic Rate Chars Sec 6 6 Characters Per Second default 8 8 Characters Per Second 10 10 Characters Per Second 12 12 Characters Per Second 15 15 Characters Per Second 20 20 Characters Per Second 24 24 Characters Per Second 30 30 Characters Per Second Typematic Delay Msec This is the interval between the first and second character displayed 250 250 msec default 500 500 msec 750 750 msec 1000 1000 msec Security Option Setup default security protection in CMOS setup menu Setting password in BIOS CMOS Supervisor Password or User Password the user needs to key in password if entering BIOS CMOS setup System security protection in system boot up amp BIOS setup This function secures the system under system boot up and BIOS setup PCI VGA Pallette Snoop Enabled it allows you to install an enhanced graphics adapter card Disabled default If your graphics adapter card does not support
29. ller utilizes with fully Plug and Play device which supports 2 88 MB Floppy Dual 16550 Compatible with 16 bytes FIFO up to 460K baud rate Serial Port ECP Enhanced Capabilities Port EPP Enhanced Parallel Port parallel port Infrared IrDA HPSIR and Amplitude Shift Keyed IR ASKIR port The main board supports 3 PCI amp 3 ISA for highest performance I O add on adapter cards The system board supports three Matrix Independent for complete multiple PCI adapters operation up to 133MB s data transfer rate on PCI bus compared to 33MB s on EISA bus synchronized operation CPU to PCI Interface for best graphical performance 120MB s PCI to system DRAM together with utilizing Snoop Ahead Features and support back to back sequential CPU to PCI Memory writes to PCI Burst Write for full PCI through put MVP3 chipset doesn t support Ultra DMA 66 mode HDD MVP3 Main Board 1 The main board is also strengthened with Power Management Wake up Event such as WOL Wake up on LAN and Modem ring on which are the new inventions to enable PCs to be turned on over the network or modem These are also key benefits in PC operation asset management new system setup and power conservation In addition to the above features this main board is a DIP switch design which offers an easier procedure to set CPU speed compared with present Pentium main boards In conclusion the main board is a combination of the highest in performance
30. n using USB keyboard CPU Warning Temperature This function is CPU over heat alarm Select either of the below temperature will give an alarm when CPU temperature is over heated Disabled 50 C 122 F 53 C 127 F 56 C 133 F 60 C 140 F 63 C 145 F 66 C 151 F 70 C 158 F Shutdown Temperature System will shut down automatically when CPU temperature is over the appointed temperature Below is the boundary which system gives alarm 60 C 140 F default 265 C 149 F 70 C 158 F 75 C 167 F Current CPU Temperature Current CPUFan1 speed CPUFan2 speed Current Vin3 V System will automatically detect the above items and show the status MVP3 Main Board 41 5MVP3 3 5 Power Management Setup BOM PCI IS BIOS Z SLELIB POWER MANAGEMENT SETUP AWARD SOFTWARE IMC ACPI function META Primary INTER Fawer Management User Def ine IBQA Z Primary PM Contral hy APM Yes IBQ4 13 Primary Video Off Option Suspend gt Off IBS LET Z Primaru Videa Off Method DPMS Support Flappy Disk Primary MODEM Use 3 IBU7 LET 1 Primary Suft ff hu Instant Off BTC Alarm Disabled PH Timers 1809 IBQZ Bedir HDD Power Dawn Disable 1819 Reserved Secondary Made Disable Reserved Yecondary Suspend Made Disable 12 P3 Z Mouse Primary ax Eventa CCapruceszzur Primary
31. nt number of pins on either side of the breaks the module will only fit in the orientation as shown DIMM MVP3 Main Board 32 Chapter 3 BIOS Setup 3 1 Award BIOS CMOS Setup BOM PCI IS A BIOS ZASLELTB CMOS SETUP UTILITY AWARD SOFTWARE TMV 32 nee INTEGHATED PERIPHERALS BIOS FEATURED SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USEE PASSWORD POWER MANAGEMENT SETUP IDE HOD AUTO DETECTION PMP PCI CONFIGURATION SAVE EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING Esc Quit Thee Select Item 10 Jave amp Exit Jetup Shift FZ Change Calar The menu displays all the major selection items and allow user to select any of shown item The selection is made by moving cursor press any direction key to the item and press lt Enter gt key An on line help message is displayed at the bottom of the screen as cursor is moving to various items which provides user better understanding of each function When a selection is made the menu of selected item will appear So the user can modify associated configuration parameters MVP3 Main Board 33 3 2 Standard CMOS Setup BOM PCI ZIS BIOS CZAhLELTH STANDARD CMOS SETUP AWARD SOFTWARE IMC Date mm dd uu Mon 16 1998 Time hh mm ss 19 34 31 HAED DISES TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR Primary Master 8 Prinary Slave 8 Jecandary Master Secondary Slave 8 Drive ft t 44M 3 5 In Drive B Hanc FIap
32. or in the secondary slave IDE hard disk drive MVP3 Main Board 69 5MVP3 5 2 Frequently Asked Questions Below is questions users always come out with Q is for question A is for answer Q Why can t my AGP card work under Win 95 A Windows 95 OSR2 0 does not support AGP function You must install USB support file to enable this function After installing choose enable for ASSIGN IRQ FOR USB in BIOS PNP PCI configuration setup Q Why can t the CPU frequency be adjusted to 100 MHz A The BIOS will automatically detect the CPU frequency 66MHz or 100 MHz Therefore if your CPU frequency cannot be adjusted to 100 MHz then your CPU may be 66 MHz In BIOS speed setup there are other frequencies like 75 MHz 83 MHz 103 MHz 102 MHz 112 MHz 133MHz These are for internal test only No guarantee is provided since this is not included in chipset specification Q Why is my system not stable with 100 MHz CPU A There are many reasons for this condition One of the most common is that SDRAM does not match PC 100 specification When system is operated under 100 MHz in addition to 100 MHz CPU SDRAM must be PC 100 DIMM too WWW LUCKY STAR COM TW MVP3 Main Board 70
33. py d Mode Support Videa EGA VG Halt On AII Errars ESC Quit Tl lt Select Item PU PD Modify Fi Help CShift F2 Change Calor The Standard CMOS Setup allows user to configure system setting such as current date and time type of hard disk drive installed in the system floppy drive type and the type of display monitor Memory size is auto detected by the BIOS and displayed for your reference When a field is highlighted direction keys to move cursor and lt Enter gt key to select The entries in the field will be changed by pressing lt PageDown gt or lt PageUp gt key or user can enter new data directly from the keyboard MVP3 Main Board 34 Hard Disk Configurations 1 TYPE select from 1 to 45 to fill remaining fields with redefined values of disk drives Select USER to fill the remaining fields Select AUTO to detect the HDD type automatically 2 SIZE the hard disk size The unit is mega byte MB 3 CYLS the cylinder number of the hard disk 4 HEAD the read write head number of hard disk The range is from 1 to 16 5 PRECOMP the cylinder number at which the disk drive changes the write timing 6 LANDZ the cylinder number that the disk drive heads read write are seated when the disk drive is parked 7 SECTOR the sector number of each track defined on the hard disk The range is from 1 to 64 8 MODE select AUTO to detect the mode type automatically If your ha
34. rd disk supports the LBA mode select LBA or LARGE However if your hard disk cyclinder is more than 1024 and does not support the Iba function you have to set at LARGE Select NORMAL if your hard disk supporting cylinder is below 1024 Note 1 if hard disk primary master slave secondary master slave were set to auto the hard disk size and model will be auto detected on display during POST Note2 halt on is to determine when to halt the system by the BIOS if error occurs during POST MVP3 Main Board 35 5MVP3 3 3 BIOS Features Setup Menu below shows all of the manufacturer s default values of this main board Move the cursor by pressing direction keys and lt PageDown gt or lt PageUp gt key to modify the parameters pressing F1 key to display help message of the selected item This setup program also provide 2 convenient ways to load the default parameter data from BIOS F6 or CMOS F7 area if shown data is corrupted This provides the system a capability to recover from any possible error ROM PCI I9A BIOS ZASLEL1R BIOS FEATURES AWARD SOFTWARE finti Virus Protection Ee Video BIOS Shadow Enabled CPU Internal Cache Enabled CH000 CBFFF Shadow Disabled External Cache Enabled 6 Shadow Disabled Quick Power Self Test Enabled D60006 D3FFF Shadow Disabled Bact Sequence C SCSI D4000 D7FFF Shadow Disabled Swap Floppy Drive Di
35. rol registers Keyboard interface controller 8042 RTC ports amp CMOS I O ports DMA register Interrupt controller slave controller slave Math coprocessor Hard disk controller Parallel port 2 Graphics adapter controller Serial port 2 Network ports Parallel port Monochrome amp parallel port adapter EGA adapter CGA adapter Floppy disk controller Serial port 1 MVP3 Main Board 60 5MVP3 4 3 Time amp DMA Channels Map Time map Timer channel 0 system timer interrupt Timer channel 1 DRAM refresh request Timer channel 2 speaker tone generator Dma channels DMA channel 0 available DMA channel 1 onboard ecp option DMA channel 2 floppy disk smc chip DMA channel 3 onboard ECP default DMA channel 4 cascade for dma controller 1 DMA channel 5 available DMA channel 6 available DMA channel 7 available MVP3 Main Board 61 5MVP3 4 4 Interrupt Map INIMI non maskable interrupt IRQ H W 0 system timer interrupt from timer 0 keyboard output buffer full 2 cascade for IRQ 8 15 3 serial port2 4 serial port I 5 parallel port 2 6 floppy disk smc chip 7 parallel port 1 8 RTC clock 9 available 10 available 11 available 12 PS 2 mouse 13 math coprocessor 14 onboard hard disk ide1 channel 15 onboard hard disk ide2 channel MVP3 Main Board 62 5MVP3 4 5 RTC amp CMOS RAM Map RTC amp CMOS 00 seconds
36. rts wireless infrared module With this module and application software like LAPlink or WIN95 Direct Cable Connection user can transfer data to or from laptops notebooks PDA and printers This connector supports HPSIR ASKIR and Fast IR Attach Infrared module to IR connector and enable BIOS Infrared function Be sure to put in the right orientation during attachment Pin 7 MVP3 Main Board 24 2 4 6 FANI FAN2 Connectors There are 2 fan connectors on SMVP3 and they are marked as FAN 1 and FAN2 Each fan connector has three pins Jeg Fan Signal Ground e o Sense 25 2 4 7 FDC Floppy Interface Floppy interface connector with 34 pins is used to attach the floppy drive cable FDC Floppy disk connector 33 1 34 2 Pin Signal Pin Signal Pin I GND 2 Data rate selection Pin3 GND 4 NC Pin5 GND 6 NC Pin7 GND 8 FDC index
37. s e Intel and Pentium are registered trademarks of Intel Corporation e IBM is a registered trademark of International Business Machines Corporation e Microsoft is a registered trademark of Microsoft Corporation e PCI is a registered trademark of PCI Special Interest Groups e AWARD is a registered trademark of Award Software Inc All other trademarks are the property of their respective owners Table of contents 2 2 2 3 2 5 2 6 Chapter 1 Introduction Main Board Overview Specifications 3 Notice of Hardware Installation 5 Chapter 2 Installation 7 Layout Reference 7 Quick reference to CPU Speed Setup 8 Jumper Settings 10 2 3 1 S1 10 2 3 2 S2 12 2 3 3 JP4 DIMM Voltage Selector 13 2 3 4 JP5 Flash ROM Voltage Selector 14 2 3 5 JP7 CMOS Status 15 Connectors 16 2 4 1 CN10 Front Panel Connectors 16 2 4 2 Back Panel Connectors 18 COM 1 COM2 18 LPT Parallel Port 19 CN8 USB 20 Keyboard 20 CN4 Mouse 21 2 4 3 CN5 ATX Power Supply Connector 22 2 4 4 CN7 AT Power Supply Connector 23 2 4 5 CN8 IR Connector 24 2 4 6 FANI FAN2 Connectors 25 2 4 7 FDC Floppy Interface 26 2 4 8 1 and IDE2 Ports 27 2 4 9 LAN 28 Expansion Slot 29 DIMM Memory Installation 31 MVP3 Main Board I 3 1 3 2 3 4 3 5 3 6 3 7 3 9 3 10 3 11 3 12 4 1 4 2 4 3 4 4 4 5 4 7
38. s 1 2 Normal 2 3 Clear CMOS Procedure to clear CMOS Step 1 Shut down the system and disconnect the power supply from AC power Step 2 Pull out the AT cable from AT connector Step 3 Short the CMOS jumper by putting jumper cap on Pin 2 3 for a few seconds Step 4 Return to pin 1 2 for normal setup Step 5 Link power cable to the connector amp connect AC power to power supply Step 6 Turn on system power an MVP3 Main Board if you d like to set password press Del Key during system bootup to enter CMOS setup and establish a new password 15 2 4 Connectors There are many connectors on this main board Refer to the following pages for details 2 4 1 CN10 Front Panel Connectors Front panel has connectors as HDD LED SOFT PWR TB LED SPEAKER KEYLOCK and POWER LED Refer to details as below ea CN10 Front Panel HDD LED T TB LED SPEAKER POWER LED SOFT PWR Marked HDD LED Hard Disk activity LED connector is a 2 pin keyed Berg strip It is used to connect to front panel Hard Disk LED ATX soft PWR switch connector is Soft PWR with 2 pins MVP3 Main Board 16 SMI connector is a 2 pin Berg strip which is also called green or sleep connector When SMI is turned from open
39. sabled DHO08 DBFFF Shadow Disabled Baat Up Floppy Seek Disabled DC000 DFFFF Shadow Disabled Baat Up MumLuck Status On Gate AZO Option Murmal Tupematic Bate Setting Disabled Typematic Bate Chars Sec 6 Typematic Delay Msec ZhB Security Option Setup PCI UGA Palette Snoop Disabled 05 Select For DRAM gt G4MH 52 Quit tl Select Item Help PU PD Modify OIld Values Shbift FZ Calar Laad Setup Defaults Anti Virus Protection Enabled Disabled default CPU Internal Cache Enabled default enable L1 cache Disabled disable L1 cache MVP3 Main Board 36 5MVP3 External Cache Enabled default enable L2 cache Disabled disable L2 cache Quick Power On Self Test This category speeds up power on self test Enabled BIOS will shorten or skip some check items Disabled normal speed Boot sequence This category determines which drive the system searches first Take A C SCST for example System will search in turn for floppy disk drive second is hard disk drive and finally SCSI drive Default value is A C SCSL Options as below A C SCSI CjA SCCI CCDROM A CDROM C A D A SCSI E A SCSI F A SCSI SCSLA C SCSLC A C Only LS ZIP C Swap Floppy Drive Enabled floppy A amp B will be swapped Disabled default floppy A amp B will be not swapped Boot Up Floppy Seek BIOS will determine if the floppy disk drive is 40 or 80 tracks 360k type is 40 trac
40. te Some OSes like SCO UNIX must use NORMAL for installation The IDE HDD AUTO DETECTION utility is a very useful tool especially when you do not know which kind of hard disk type you are using You can use this utility to detect the correct disk type installed in the system automatically or you can set hard disk type to auto in the standard CMOS setup You don t need the IDE HDD Aauto Detection utility The BIOS will auto detect the hard disk size and model on display during post MVP3 Main Board 53 5MVP3 The Award amp BIOS supports 3 HDD modes NORMAL LBA amp LARGE 1 Normal mode Generic access mode in which neither the BIOS nor the IDE controller will make any transformations during accessing The maximum number of cylinders head amp sectors for normal mode are 1024 16 amp 63 No Cylinder 1024 X No Head 16 X No Sector 63 X Per Sector 512 528 MB If user set this HDD to normal mode the maximum accessible HDD size will be 528 MB even though its physical size may be greater than that 2 LBA Logical Block Addressing Mode A new HDD accessing method to overcome the 528 MB bottleneck The number of cylinders heads amp sectors shown in setup may not be the number physically contained in the HDD During HDD accessing the ide controller will transform the logical address described by sector head amp cylinder into its own physical address inside the HDD The maximum HDD size
41. the pallette snoop function please set at Disabled to avoid system malfunction MVP3 Main Board 38 5MVP3 OS Select For DRAM 64MB This option is especially set for OS2 operating system Set Non OS2 for RAM memory over 64MB and set Non OS2 for other operating systems like Windows 95 98 or NT Non OS2 default OS2 Video BIOS Shadow It determines whether video BIOS will be copied to RAM However it is optional from chipset design Video shadow will increase the video speed Enabled Video Shadow is enabled default Disabled Video Shadow is disabled C8000 CBFFF Shadow CC000 CFFF Shadow D0000 D3FFF Shadow D4000 D7FFF Shadow D8000 DBFFF Shadow DC000 DFFF Shadow These are categories determining whether optional ROM will be copied to RAM by 16KB or 32KB per unit and the size depends on chipset Enabled Disabled default MVP3 Main Board 39 5MVP3 3 4 Chipset Features Setup BOM BIOS CZRGLELTB CHIPSET FEATURES SETUP AWARD SOFTWARE INC Bank Ort DRAM Timing ABEBDEFERHI nChip USB Enabled Bank 27 3 DEAN Timing Ecyhaard Support Disabled Bank 4 5 DREAM Timing FPYEDO SDBAM Cycle Length 3 CPU Warning Temperature h C 122 F DRAM Head Pipeline Enabled Shutdown Temperature BO C TI40 F Sustained Write Enabled Current CPU Temperature Cache Bd CPU Wt Pipeline Enabled Current CPUFAMI Speed Cache Timing Fast Current CPUFANZ Speed Video BIUS
42. ther line is shown ECP Mode Use DMA 3 default 1 MVP3 Main Board 49 5MVP3 3 8 Supervisor User Password The Supervisor User Password setting utility sets the security protection There are two kinds of password functions in the setup menu one is Supervisor Password and the other is User Password Their difference is Supervisor Password this function allows you the right to change the options of setup menu User Password this function only allows you to enter the setup menu but not to change the options of the setup menu except USER PASSWORD SAVE amp EXIT SETUP and EXIT WITHOUT SAVING 1 How to set Supervisor Password amp User Password The setup of Supervisor Password and User Password have the same steps Step 1 Enter Password Press Enter after appointing the password BIOS ZRSLBLIC SING CA BIDS EEATIBES SENP Exc uit Select Item Save Exit Sctap ShRiEt FZ Change Calar MVP3 Main Board 50 5MVP3 Step 2 Confirm Password Typing the password again and pressing Enter Nf PCL ISA BIOS ZMLBLIC 3105 FEATERES SETUP CHIPSET EEATHAES SETUP acr ee ICONFIRM PASSWORD EXIT ULITHOUT SAVING Esc Quit Thee Select Item Fifi Seer Exit Sciup ShiFt EZ Change Color M Note If you forget password please clear CMOS refer to Jumper JP7 CMOS status St
43. umper Settings With a careful design for the CPU speed jumper this main board has been simplied to a DIP Switch form It is very convenient to set CPU speed under DIP switch 2 3 1 S1 S1 Pin 1 to Pin 3 CPU Ratio Selector S1 CPU Ratio Pin 1 Pin 2 Pin 3 off off off 1 5 3 5x on off off 2 0x on on off 2 5x off on off 3 0x on off on 4 0x on on on 4 5 off on on 5 0x off off on 5 5x MVP3 Main Board 10 S1 Pin 4 to Pin 6 CPU Frequency Selector S1 CPU Frequency Pin 4 Pin 5 Pin 6 on on on 60 MHz off on on 66 6 MHz on on off 75 MHz off on off 83 3 MHz on off off 95 MHz off off off 100 MHz S1 Pin 7 SDRAM Clock Frequency S1 Pin 7 SDRAM Clock Ereq on SDRAM clock is fixed on 66 MHz off SDRAM Clock is the same with CPU clock MVP3 Main Board 11 2 3 2 S2 CPU Voltage Selector ini i C 2 CPU voltage selector did NO S2 CPU Vcore Pin 1 Pin 2 Pin 3 Pin 4 on off off off 2 1V off on off off 2 2V off off on off 2 4V on on on o
44. und Pin 6 Data bit 4 Pin 19 Ground Pin 7 Data bit 5 Pin 20 Ground Pin 8 Data bit 6 Pin 21 Ground Pin 9 Data bit 7 Pin 22 Ground Pin 10 IACK Pin 23 Ground Pin 11 Busy Pin 24 Ground Pin 12 Pin 25 Ground Pin 13SLCT MVP3 Main Board 19 USB Universal Serial Bus Universal Serial Bus connector marked USB is used to connect USB devices There are 2 USB connectors on this main board USB BM Keyboard The onboard PS 2 keyboard and mouse connector is 6 pin Mini Din connectors marked KB KB Keyboard connector Pin Description Pin I Data signal Pin2 NC A Pin 3 Ground a Pin 4 5V DC Pin 5 1 signal Pin 6 INC MVP3 Main Board 20 CN4 Mouse CN4 is a 4 pin connector to connect to mouse connector CN4 PS 2 mouse Pinl MVP3 Main Board 21 2 4 3 5 ATX Power Supply Connector ATX power supply connector has 20 pins which is designed for ATX case especially The ATX power supply supports the function of the
Download Pdf Manuals
Related Search