User`s Manual - NeoMedia Technologies, Inc
Contents
1. Send the following command to the scanner via the hardware interface the scanner and the controlling de vice are connected with Three ASCII characters SYN M CR ASCII 22 77 13 fol lowed by the ASCII command TRGMODS the closing exclamation mark is part of the command sequence and has to be present The scanner responds to these commands with the command TRGMODx one of three responses as fol lows and the exclamation mark to close the response ACK Indicates a good command which has been proc essed ENQ or NAK Indicates an invalid command this means that there most probably was a typing error in the command syntax Example TRGMODOACK re NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 34 Diverse APPENDIX B Diverse This chapter contains information on Warranty conditions rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Diverse Warranty conditions of NeoMedia Europe AGWarranty conditions of NeoMedia Europe AG Page 3 Warranty conditions of NeoMedia Europe AG 1 Warranty coverage a The warranty covers the equipment delivered and all its parts Parts will at NeoMedia Europe s sole discretion be replaced or repaired free of charge if despite proven proper handling and adheren2. b In the case of any externally visible damage arising from transport e g damage to the housing the person carrying out the transportation and the sender should be informed immediately On discovery of damage which is re NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 36 Diverse Warranty conditions of NeoMedia Europe AG not externally visible the transport company and the sender are to be im mediately informed in writing at the latest within 3 days of delivery Transport to and from the location where the warranty claim is accepted and or the repaired device is exchanged is at the purchaser s own risk and cost Warranty claims are only valid if a copy of the original purchase receipt is re turned with the device 4 Suspension of the warranty All warranty claims will be deemed invalid if the label with the serial number has been removed from the device if the device is damaged or destroyed as a result of acts of nature or by envi ronmental influences moisture electric shock dust etc if the device was stored or operated under conditions not in compliance with the technical specifications if the damage occurred due to incorrect handling especially to non observance of the system description and the operating instructions if the device was opened repaired or modified by persons not contracted
3. About displays version numbers and Copyright information re NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 22 Configuring XELIA RS 232 RS 232 Baud Rate RTS CTS defines the data transmission rate from the XELIA scanner to the terminal via the serial interface Host terminal must be set to the same baud rate as the XELIA Default Baud Rate 38400 BPS defines the data exchange between XELIA and host ter minal RS 232 handshaking If checking the box R7S CTS XELIA issues always an active RTS signal to the receiving device XELIA waits to send its data until it detects an active CTS signal from the receiv ing device XELIA then sends its data while checking the CTS signal before the transmission of each data character If an inactive CTS signal is detected at any time the XELIA halts transmission until it detects another active CTS sig nal Default RTS CTS activated Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Configuring XELIA Output Page 23 Output Reread Delay sets the time period before the XELIA can read the same bar code a second time Longer delays are effective in minimizing accidental rereads at the point of sale Use shorter delays in applications where repetitive barcode
4. User s Manual Version 1 1 m NEO 2009 NeoMedia Europe AG W rselen Germany While the information in this manual has been compiled with great care it may not be deemed an assurance of product characteristics NeoMedia Europe AG shall be liable only to the degree specified in the terms of sale and delivery Trademarks NeoMedia is a registered trademark of NeoMedia Technologies Inc XELIA is a registered trademark of NeoMedia Europe AG Windows Windows NT and Windows Vista are registered trademarks of Microsoft Corp All other names mentioned may be trademarks or registered trademarks of their respective owners Subject to change without notice No liability for technical errors or omissions Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Table of contents Page 3 Table of contents ABOUT THIS MANUAL 5 CHAPTER 1 INTRODUCTION 6 XELIA short description 7 XELIA scanner models 8 XELIA optional accessories 8 CHAPTER 2 UNPACKING AND CONNECTING XELIA 9 Packaging contents 10 Installing and connecting XELIA 11 Connecting XELIA using the USB port 11 Connecting XELIA using the serial port 11 Installing XELIA E using the Ethernet port 12 CPR Manager 13 CHAPTER 3 SETUP TOOL 14 Installation requirements 15 Operating systems 15 Installing the XELIA Setup Tool 16 Starting the
5. Now install the software provided on the configuration CD and be sure to follow the instructions for your specific operating system Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Unpacking and connecting XELIA CPR Manager Page 13 CPR Manager Open the CPR Manager Click Add Remove Select a free COM port and click OX to create a virtual COM port Mark the new COM port by clicking on it Click Search For Devices to scan your network for available XELIAs Right click on the correct XELIA device in the device list at the bottom and choose Add To Settings Click Save and close the CPR Manager Remark You need administrator rights to create a virtual COM port using the CPR Manager CPR Manager 9 4 2 1 1 lal x Eile ComPort Device Tools Help TY AddjRemove save 2 Refresh jJ Search For Devices Gp Exclude Com Ports Hide Settings Com Tests ES All Com Ports 8 Com EME Com1 9 Y Window s Port Name CPR a Port COM8 Y Window s Device Name Device GcprDevice8 Com Status Closed Y Window s Service Name GcprDrvr Network Status Disconnected I Reset to Defaults Cancel Edits 2 Com 8 IV Buffer Writes Keep checked for better write performance Connection Timeout in seconds v Server Reconnect IV Timeout Reconnect 0 3 Reconnect Limit 0 forever No Net Close List
6. The XELIA Setup Tool is a program designed to configure your XELIA in order to achieve optimal reading results With this program you can carry out all neces sary parameterizations and main settings adapt them to your specific needs and suit your individual area of application In most cases the default settings are sufficient In this chapter you will learn how to install remove start and exit the XELIA Setup Tool Installing the XELIA Setup Tool Removing the XELIA Setup Tool Starting the XELIA Setup Tool Exiting the XELIA Setup Tool rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Setup Tool Installation requirements Page 15 Installation requirements To install and run the XELIA Setup Tool your computer must fulfill the following requirements Operating systems To install the XELIA Setup Tool following operating systems are required Windows 2000 Windows XP 32 bit versions only Windows Vista 32 bit versions only Should you use other operating systems please contact our support contact address on page 5 Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 16 Setup Tool Installing the XELIA Setup Tool Installing the XELIA Setup Tool Switch on your computer and w
7. USB Power amp I O XELIA E Connectors USB Power amp I O Ethernet rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 44 Technical Data XELIA XELIA E Connector Pin out XELIA XELIA E Connector Pin out r1 La USB Standard USB B connector to connect scanner to a USB host device via the supplied USB cable Power amp I O RJ45 socket with NeoMedia proprietary pin out as fol lows Type Signal Direction Remark 1 RS232 RTS OUT RS232 gs Jo omn la R232 TX o la rs232 pex o NN 5 Rs232 JO Power GND 6 mo GOODREaD ouT__ 3 3V against GND 7 lo TRIGGER N 33VagainstGND 8 Powr vc 12V500mAmax Direction seen from scanner XELIA is DTE in RS232 mode For GOODREAD and TRIGGER signals please refer to the command description of the Good Read and Trigger commands in the Setup Tool 2 Ethernet only available on XELIA E Standard RJ45 Ethernet Port for 10BASE T and 100BASE TX connection NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com
8. by NeoMedia Europe if the device shows any kind of mechanical damage if the warranty claim has not been reported in accordance with 3a or 3b 5 Operating mistakes If it becomes apparent that the reported malfunction of the device has been caused by unsuitable hardware software installation or operation NeoMedia Europe reserves the right to charge the purchaser for the resulting testing costs 6 Additional regulations a The above conditions define the complete scope of NeoMedia Europe s legal liability The warranty gives no entitlement to additional claims such as any refund in full or in part Compensation claims regardless of the legal basis are ex cluded This does not apply if e g injury to persons or damage to private property are specifically covered by the product liability law or in cases of intentional act or culpable negligence NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Diverse Warranty conditions of NeoMedia Europe AG Page 37 c Claims for compensation of lost profits indirect or consequential detri ments are excluded d NeoMedia Europe is not liable for lost data or retrieval of lost data in cases of slight and ordinary negligence e In the case that the intentional or culpable negligence of NeoMedia Europe employees has caused a loss of data NeoMedia Europe will be liable fo
9. AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 20 Configuring XELIA CHAPTER 4 Configuring XELIA This chapter describes the XELIA Setup Tool how to configure the XELIA scanner according to your specific needs how to set up the decoding methods and how to define the communication between XELIA and host system FT NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Lel T 492405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Configuring XELIA Menu bar Page 21 Menu bar Menu Connection Connect establishes a connection to the XELIA Disconnect closes the connection to the XELIA Quit closes the setup tool application Menu Configuration Default sets all parameters in the setup tool to default values and writes them directly to the XELIA scanner s EEPROM Apply writes the current parameter set of the XELIA scanner to EEPROM Important if you do not apply all your parame ters will be lost in case of a power interruption Open loads a parameter set from a file into the setup tool and transmits it to the XELIA Click on App y to have them saved and written to EEPROM Save saves the current parameter set from the setup tool to a file Menu mage Snapshot creates automatically a snapshot image from the XELIA scan ner and displays this image in a separate window Menu He p
10. Connections Display 2d Data Matrix ECC200 QR Aztec PDF417 1d UPC EAN JAN 2 5 Interleaved Code 128 various other codes on request Honeywell Adaptus Imaging Technology Omni directional On glass level approx 55x45 mm From glass to approximately 5 cm above glass Powered via USB or via optional wall power sup ply 100 240V AC 0 6A max USB powered via the USB connection RS 232 4 800 115 200 Bit s 8 Bit no parity HW handshake Ethernet only on XELIA E Configuration via built in Web Server 10 100Base T TX auto sensing IP Address via DHCP client or fixed Full TCP IP stack UDP support Virtual serial port device driver for Windows 1 input 1 output Beeper for successful reading rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 40 Technical Data Data sheet XELIA XELIA E Connector Pin out Mechanical Data Housing Aluminum thermoplastic Weight 450g Dimensions Height 110 125 mm Width 84 mm Depth 93 mm Environmental Data Operating 0 C 40 C 32 F 104 F Storage 40 C 70 C 40 F 158 F non condensing Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Technical Data ASCII conversion chart Page 41 ASCI
11. emits a beep sequence via the built in speaker and the scanning illumination starts to flicker Connecting XELIA using the serial port Switch on your computer Connect one end of the serial interface cable to XELIA middle port and the other end of the cable to the matching serial port of your PC Then plug the power supply unit into an electrical outlet The scanner emits a beep sequence via the built in speaker and the scanning illumination starts to flicker Remark You don t need to install a software driver for a serial communication If connecting the XELIA scanner using an RS 232 interface all communication parameters between XELIA and terminal must match for correct data transfer through the serial port using RS 232 protocol The default settings for the Xelia serial port are 38 400 Bit s No Parity 8 Data Bits 1 Stop Bit RTS CTS Hand shake m NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ll T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Seite 12 Unpacking and connecting XELIA Installing and connecting XELIA Installing XELIA E using the Ethernet port Connect one end of the Ethernet cable to the Ethernet port right most port on the back of the XELIA E scanner and the other end of the cable to an Ethernet port of your network For the power supply connection of your XELIA E plug the provided power supply unit into an electrical outlet
12. AN 73 barcodes with 2 dig its at the end Default inactivated 5 Digit Addenda enables the decoding of EAN AN 73 barcodes with 5 dig its at the end Default inactivated Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Configuring XELIA EAN JAN 8 Page 25 EAN JAN 8 Enabled Addenda required 2 Digit Addenda 5 Digit Addenda enables disables the decoding of EAN AN 8 barcodes Default activated allows you to specify whether the check digit should be transmitted at the end of the scanned data or not If you checked this box only AW AN 8 barcodes with a check digit at the end will be decoded The ones without ad denda will be ignored Default inactivated enables the decoding of A V AN 8 barcodes with 2 digits at the end Default inactivated enables the decoding of FAN AN 8 barcodes with 5 digits at the end Default inactivated Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 26 Configuring XELIA UPC A UPC A Enabled enables disables the decoding of UPC A barcodes Default activated Addenda required allows you to specify whether the check digit should be transmitted at the end of the scanned data or not If you checked this box only UPC A barcodes w
13. I conversion chart Remark This table applies to U S style keyboards Certain characters may dif fer depending on your Country Code PC regional settings ms or s Ho 5 n m e epe Hos w i Hor os k Hos ec m 4 Im ws m mo ee m ar o m or so s e Anz mo s s a m I fa m e IR m z ms m s mr m fu a O as 5 V sr w us 7 V mjn end HE EH 4 O gt Es e s Y joo s z z a fse t ma re i s 5 TN a s ws ve s s pim rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 42 Technical Data ASCII conversion chart XELIA XELIA E Connector Pin out e NIYO N oO Lu oj lawj eoj sriujojrjvojoj J cza ul LL Ww LLI Ww LLI LLI LU LU tr D TE ap pes je Ee p YES PH pans ES 86 68 rns Ue ue T E LL LE E El E Ed E EI MIN E m E E rtis Gi 3 ci 3 3 Gi Y X e E CN CN CN CN D S 3 S o 3 S S 3 e S 5 2 ce ee A ee ime mmm om S N N S Mila ll NINNIN NINININI NINI NINININI NINININI NINININI CN CN CN 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com NeoMedia Europe AG Jens Otto Krag Str 11 rm E Technical Data XELIA XELIA E Connector Pin out Page 43 XELIA XELIA E Connector Pin out XELIA Connectors
14. XELIA Setup Tool 17 Exiting the XELIA Setup Tool 18 Removing the XELIA Setup Tool 19 CHAPTER 4 CONFIGURING XELIA 20 Menu bar 21 RS 232 22 Output 23 EAN JAN 13 24 EAN JAN 8 25 UPC A 26 re NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 4 Table of contents UPC EO 27 Code 128 28 Interleaved 2 of 5 29 2D symbologies 30 Additional Commands 31 APPENDIX A TRIGGER COMMANDS 32 Trigger commands 33 APPENDIX B DIVERSE 34 Warranty conditions of NeoMedia Europe AG 35 1 Warranty coverage 35 2 Warranty period 35 3 Warranty procedure 35 4 Suspension of the warranty 36 5 Operating mistakes 36 6 Additional regulations 36 APPENDIX C TECHNICAL DATA 38 Data sheet 39 ASCII conversion chart 41 XELIA XELIA E Connector Pin out 43 XELIA Connectors 43 XELIA E Connectors 43 XELIA XELIA E Connector Pin out 43 XELIA XELIA E Connector Pin out 44 r1 La NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com About this manual Page 5 About this manual Thank you for placing your trust in our XELIA desktop scanner This manual contains all important information you will need to configure and operate your XELIA For instance how to physically install the unit in its in tended location how to set i
15. ait until Windows is started Insert the provided configuration CD into the CD ROM disk drive The Install program will start automatically If the auto start function is disabled start setup manually by double clicking on SETUP EXE in the CD root directory Confirm the next installation dialogue with Next Remark If needed log in with administration rights for the local computer In stall the Setup Tool using an administrator account Select the destination folder to install the Setup Tool and click then on Next Click again on Nextto confirm and start the installation The successful installation is complete and a corresponding dialogue message appears Click on Close Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Setup Tool Starting the XELIA Setup Tool Page 17 otarting the XELIA Setup Tool Switch on your computer and wait until Windows is started Select Start gt Programs gt XELIA Setup Tool Select the appropriate connection according to the way you have connected XELIA to your PC Network RS 232 or USB Remark If connecting the XELIA scanner using an RS 232 interface all commu nication parameters between XELIA and terminal must match for correct data transfer through the serial port using RS 232 protocol Connect x How do you want to connect to the device Y C Net
16. anner behaviour in a wider scope than the standard commands in the graphi cal user interface above NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Trigger Commands Page 32 APPENDIX A Trigger Commands XELIA is usually running in Presentation Mode This means that it continuously captures images and tries to decode existing bar and 2D codes No triggering of the code reading is necessary If an application however wants to disable code reading for a certain period of time the code reading can be disabled and re enabled using dedicated com mand syntax as described on the following page Trigger Commands Trigger commands Page 33 Trigger commands Disable Code Reading This command is used to disable code reading until the Enable Code Reading Responses reading is re enabled via the Enable Code Reading command as described below or the scanner has been switched off and on again Send the following command to the scanner via the hardware interface the scanner and the controlling de vice are connected with Three ASCII characters SYN M CR ASCII 22 77 13 fol lowed by the ASCII command TRGMODO the closing exclamation mark is part of the command sequence and has to be present This command is used to re enable code reading until the reading is disabled via the Disable Code Reading command as described above
17. ce to the operating instruc tions these parts became defective due to fabrication and or material de fects Alternatively NeoMedia Europe reserves the right to replace the de fective product with a comparable product with the same specifications and features Operating manuals and possibly supplied software are excluded from the warranty b Material and service charges shall be covered by NeoMedia Europe but not shipping and handling costs involved in transport from the buyer to the ser vice station and or to NeoMedia Europe c Replaced parts become property of NeoMedia Europe d NeoMedia Europe is authorized to carry out technical changes e g firmware updates beyond repair and replacement of defective parts in order to bring the equipment up to the current technical state This does not result in any additional charge for the customer A legal claim to this service does not ex ist 2 Warranty period The warranty period for this NeoMedia Europe product is twelve months The warranty period begins at the day of delivery Warranty services carried out by NeoMedia Europe do not result in an extension of the warranty period nor do they initiate a new warranty period The warranty period for installed re placement parts ends with the warranty period of the device as a whole 3 Warranty procedure a If defects appear during the warranty period the warranty claims must be made immediately at the latest within a period of 7 days
18. d via the USB port in this connection method and a serial port to connect your XELIA scanner to any serial device The serial cable with power supply is not included in the package refer to XEL A optional accessories on page 8 The model with Ethernet XELIA E possesses an Ethernet interface in addition to the USB and serial ports The USB cable is provided with this scanner model The serial cable with power supply and the Ethernet cable are not included in the package refer to XEL A optional accessories on page 8 Remark XELIA in the scope of this manual refers to XELIA and XELIA E If a fea ture or function is related to only one of the two models this manual refers to XELIA only or XELIA E only XELIA optional accessories The following optional accessories for XELIA and XELIA E are currently available at NeoMedia Europe Serial cable with power supply for XELIA and XELIA E to connect your XELIA XELIA E to a wide variety of serial devices or to run XELIA E in Ethernet connection mode rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Unpacking and connecting XELIA Page 9 CHAPTER 2 Unpacking and con r1 La necting XELIA This chapter provides an overview on the XELIA components and includes in structions on how to install and connect the XELIA scanner to a PC for evalua tion Packaging content
19. en Mode Normal port closed after disconnect TCP Port Add To Firewall TCP Keep live 720000C Keep live Time msec 1900 Keep live Interval msec RFC2217 DTR In Tie DTR to DCD DSR always active TruPort Service Host I TCP Port r WARNING If the Host is on the other side of a router or a remote 1 CN firewall then UDP ports 30718 43282 and 43283 may need to be 10 0 0 77 10001 added to the firewall s exclusion list You may experience trouble 2 opening this com port if these UDP ports are not excluded 3 Also some legacy device servers respond on UDP port 43283 If you 4 are unable to connect to a device server one possible cause is the 5 ai Firewall on this machine is blocking this port Press the Add Rx Port button to add this port to the Firewall If the button caption reads 6 Remove Rx Port then the port has already been added and can be 7 a removed by pressing this button 8 ic Add Ax Port TheFirewallis turned OFF gt Device List Collapse IP Address TCP Port Product Hw Address Network Interface Device Name r1 L S8 10 0 0 77 10001 XPort 03 X5 00 20 4A A6 44 21 10 0 0 105 NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Seite 14 Setup Tool CHAPTER 3 setup Tool
20. er that incorporates Honeywell Adaptus Imag ing Technology 5 0 to enable high performance reading of 2D codes from mo bile phone displays Thanks to its high speed processor XELIA automatically recognizes 2D codes sent as text messages SMS EMS or MMS messages as well as printed 1D bar codes It rapidly processes codes with extreme accuracy 1 SEND CODE 2 CUSTOMER 3 SCAN 4 REDEEM AT POS RECEIVES Equipped with various communication interfaces XELIA can be easily integrated into an existing system in order to provide increased flexibility for mobile phone based applications at the point of sale shopping malls grocery stores and offices or point of access concert venues theme parks movie theatres sporting events Its compact size and sleek design make XELIA ideal for counter top use at a point of sale or service desk It can also be used for sweep stakes mobile advertising tickets and coupons and boarding passes Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 8 Introduction XELIA scanner models XELIA scanner models XELIA exists in two versions with and without Ethernet connectivity The model without Ethernet XELIA has two interfaces a USB port to allow you to connect your XELIA scanner directly to you PC using the included USB cable a power supply is not required since the scanner is powere
21. he minimum length of an nterleaved 2 of 5 bar code that will be accepted once scanned The length var ies from 2 to 80 characters Check the box Enabled to de fine the minimum length Minimum Default 4 Max Message length defines the maximum length of an nter eaved 2 of 5 bar code that will be accepted once scanned The length var ies from 2 to 80 characters Check the box Enabled to de fine the maximum length Maximum Default 80 NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 30 Configuring XELIA 2D symbologies 2D symbologies QR enables disables the decoding of OR codes Default inactivated Data Matrix enables disables the decoding of Data Matrix codes Default activated Aztec enables disables the decoding of Aztec codes Default inactivated PDF417 enables disables the decoding of PDF477 codes Default inactivated Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Configuring XELIA Additional Commands Page 31 Additional Commands r1 La This window is for maintenance purposes only NeoMedia technical support might be responding to your special requests by sending you a set of special commands to be entered here These additional commands can configure the sc
22. ith a check digit at the end will be decoded The ones without addenda will be ignored Default inactivated 2 Digit Addenda enables the decoding of UPC A barcodes with 2 digits at the end Default inactivated 5 Digit Addenda enables the decoding of UPC A barcodes with 5 digits at the end Default inactivated Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Configuring XELIA UPC EO Page 27 UPC EO Enabled Addenda required 2 Digit Addenda 5 Digit Addenda enables disables the decoding of UPC 0 barcodes Default activated allows you to specify whether the check digit should be transmitted at the end of the scanned data or not If you checked this box only UPC 0 barcodes with a check digit at the end will be decoded The ones without addenda will be ignored Default inactivated enables the decoding of UPC 0 barcodes with 2 digits at the end Default inactivated enables the decoding of UPC EO barcodes with 5 digits at the end Default inactivated Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 28 Configuring XELIA Code 128 Code 128 Enabled enables disables the decoding of Code 728 barcodes Default inactivated Min Message length define
23. r those costs typical to the recovery of data where periodic security data back ups have been made f The warranty is valid only for the first purchaser and is not transferable g The court of jurisdiction is located in Aachen Germany in the case that the purchaser is a merchant If the purchaser does not have a court of jurisdic tion in the Federal Republic of Germany or if he moves his domicile out of Germany after conclusion of the contract NeoMedia Europe s court of juris diction applies This is also applicable if the purchaser s domicile is not known at the time of institution of proceedings h The law of the Federal Republic of Germany is applicable The UN commer cial law does not apply to dealings between NeoMedia Europe and the pur chaser Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Seite 38 Technical Data APPENDIX C Technical Data This chapter contains information on Data sheet ASCII conversion chart XELIA XELIA E Connector Pin out rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Technical Data Data sheet Page 39 Data sheet Supported codes Code types Optical Data Imager Reading direction Field of view Depth of field Electrical Data Interfaces Interface type
24. s Installing and connecting XELIA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Seite 10 Unpacking and connecting XELIA Packaging contents Packaging contents Please check the completeness of your XELIA package The package consists of 1 XELIA 1 Configuration CD 1 USB cable Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Unpacking and connecting XELIA Installing and connecting XELIA Page 11 Installing and connecting XELIA The XELIA scanner can be connected to a PC for evaluation and individual configuration XELIA can be connected via USB serial or Ethernet port Connecting XELIA using the USB port Switch on your computer First install the software driver provided on the configuration CD if your PC is running under Windows and be sure to follow the instruc tions The software driver creates a virtual COM port which can be used like any other standard COM port on your PC Remark Linux operating systems don t require an extra driver installation De fault serial over USB driver will be used Connect one end of the included interface cable to the XELIA left most port and the other end of the cable to the matching USB port of your PC Power supply is not required The scanner
25. s the minimum length of a Code 728 barcode that will be accepted once scanned The length varies from O to 80 characters Check the box Enabled to define the minimum length Minimum Default 0 Max Message length defines the maximum length of a Code 728 barcode that will be accepted once scanned The length varies from O to 80 characters Check the box Enabled to define the maximum length Maximum Default 80 Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Configuring XELIA Interleaved 2 of 5 Page 29 Interleaved 2 of 5 Enabled Check Digit Min Message length enables disables the decoding of nterleaved 2 of 5 bar codes Default inactivated allows the XELIA to read and transmit barcode data with or without check digit Check the box Enabled to set this function When Check Digit is set to No Check Digit XELIA reads and transmits barcode data with or without check digit When Check Digit is set to Validate but Don t Trans mit XELIA only reads Interleaved 2 of 5 barcodes printed with a check digit but will not transmit the check digit with the scanned data When Check Digit is set to Validate and Transmit XELIA only reads Interleaved 2 of 5 barcodes printed with a check digit and will transmit this digit at the end of the scanned data Default No Checked Digit defines t
26. scanning is required Default delay Off Prefix and Suffix characters are data characters that can be sent before and af ter scanned data Prefix Scanneddata Suffix 1 11 Variable length 1 11 Alpha numeric Alpha numeric characters characters You can specify if prefix and suffix characters should be sent with all symbolo gies Remark Prefix and suffix should be added according to the hex values from the ASCII conversion chart on page 41 Prefix defines the prefix that will be sent before the scanned data Enter here the hex values determined from the ASCII conversion chart on page 41 Default Prefix none Suffix defines the suffix that will be sent after the scanned data Enter here the hex values determined from the ASCII con version chart on page 41 Default Suffix none rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 24 Configuring XELIA EAN JAN 13 EAN JAN 13 Enabled enables disables the decoding of EAN AN 73 barcodes Default activated Addenda required allows you to specify whether the check digit should be transmitted at the end of the scanned data or not If you checked this box only AW AN 7 3 barcodes with a check digit at the end will be decoded The ones without ad denda will be ignored Default inactivated 2 Digit Addenda enables the decoding of EFAN
27. t up to operate on your specific network and ac cording your user specific reading parameters how to get optimal reading re sults The accompanying setup tool will be described and you will find detailed in formation on its basic functions and features The following information addresses to experienced users with knowledge of the hardware and software configuration If you have further questions or need additional help please contact our sup port NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Phone 49 2405 49922 50 Fax 49 2405 49922 99 E Mail support neom com Remark Please collect the version number of the Setup Tool software the de vice information of your XELIA device code reader and Ethernet tabs before asking for technical support re NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 6 Introduction CHAPTER 1 Introduction This chapter provides general information about the XELIA desktop scanner and its optional accessories XELIA short description XELIA different scanner models XELIA optional accessories rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Introduction XELIA short description Page 7 XELIA short description XELIA is a versatile desktop scann
28. work 5 IMAC Adress Scan Change IP C Rs 232 toshiba Software Modern AMR y 38400 e USB 5180 Area Imager COMB Cancel OK Click on OK Connection will be established rA NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Li T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Page 18 Setup Tool Exiting the XELIA Setup Tool Exiting the XELIA Setup Tool Go to Connection in the menu bar of the XELIA Setup Tool and select the menu item Disconnect or click on the icon Disconnect below the menu bar Connection to the device will be disconnected Close the window by clicking on the cross in the upper right corner or selecting Connection gt Quit from the menu bar Fr NeoMedia Europe AG Jens Otto Krag Str 11 52146 W rselen Germany Ld T 49 2405 499 22 0 F 49 2405 499 22 99 info neom com www neom com Setup Tool Removing the XELIA Setup Tool Page 19 Removing the XELIA Setup Tool Switch on your computer and wait until Windows is started Remark If needed log in with administration rights for the local computer Select Start gt Settings gt Control Panel and open the Software di rectory Locate the XEL A Setup Tool program already installed on your sys tem and click the button Change Remove Confirm the next dialogue with OK Close the window Software Fr NeoMedia Europe
Download Pdf Manuals
Related Search