D014-GO Lighting Manual.indd
Contents
1. IK02 View I I 3D view Top view Front view Bottom view www goenergyeffective com Page 12 GOs IKO2 Point Bracket Application 3D view Bottom view mm ___ Side view Top view www goenergyeffective com Page 13 1 Mark the four corners of the FLL outline on the ceiling Make an opening in the ceiling to fit the PSU approx 160x430mm 2 Assemble ONE IK02 top corner bracket 3 Install the diagonally opposite bracket to the bottom bracket on the ceiling and as shown above B insert the product as shown above A 4 Repeat the same process for other two corners C and D www goenergyeffective com Page 14 GOs IKO3 Installation ZN lt 4e 4mm IKO3 screw 3 9e6 46mm gt e 8 50mm IKO3 Cap External diameter e 8 5mm 3D view Top view Front view www goenergyeffective com Page 15 150 600 OO DAZ 2 Drill four 4 2mm holes as shown above 150 3 Mark the ceiling to match the drilled holes on the FLL frame 1 Make an opening on the ceiling as shown above to accommodate PSU 4 Drill pilot holes 2 5mm 3mm on the ceiling NEL 30mm N Bit B34 Small Philips 5 Use the screws to secure the FLL module to the ceiling Do not over torque Ensure screws are securely anchored 6 After securing the FLL module to the ceiling cover the screw head with IKO3 cap www goenergyeffect2. Master 6 All Master Slave 1 2 n Set up as group 1 Press 1 on remote to assign then use UP or DOWN buttons to dim Set up as group 2 Press 2 on remote to assign then use UP or DOWN buttons to dim Set up as group 3 Press 3 on remote to assign then use UP or DOWN buttons to dim Set up as group 4 Press 4 on remote to assign then use UP or DOWN buttons to dim Set up as group 5 Press 5 on remote to assign then use UP or DOWN buttons to dim Set up as group 6 Press 6 on remote to assign then use UP or DOWN buttons to dim No group is assigned stand alone use Set up as slave operating as per master Page 9 S GO Types of DC extension wires LS ea PA018 50 F B Type A Feedback wire No feedback PAO19 50 No F B POR Type B ys dif 2 PA022 100 F B da LI Type A if PA023 100 No F B il Type B PA026 200 F B Type A F B Type B F B Type A PA018 PA022 PA019 PA023 PA027 200 No F B PA026 PA027 Type B FLL RO1 A Type Type A Typ B Type B Type PSU Note One PSU must have one A type DC extension wire no matter how many RO1s are connected to one PSU www goenergyeffective com Page 10 GOs IKO1 T Bar Installation 1 Place FLL onto T Bar 2 Seat FLL securely on T Bar 3 Wiring refer to page 8 On Off test ZZ lk 4 On Off Test Note www goenergyeffective com Page 11 GO ee IKO2 Installation ee IKO2 Assembly
3. a very slim lighting appliance at only 23 5mm thick Can be installed in a shallow or no plenum area www goenergyeffective com Contents About GO FLL Components Wiring IR Sensors PSU Power Supply Unit Connecting Network Single Zone Remote Control Multi zone Remote Control Multi zone Setup IKO1 T Bar Installation IKO2 Installation IKO3 Installation IKO5A Installation IKO5B Installation IKO6 Installation C series installation Troubleshooting 11 12 15 19 20 22 27 29 Page 2 GOs Components Base Parts IR Sensor Remote Control Style may vary depending upon the GO FLL model and features selected www goenergyeffective com Manual DC Extension Standard lengths are 50cm 1m 2m Special lengths are available to your requirements Network Cable Standard lengths are 1m 2m 5m 10m Special lengths are available to your requirements Page 3 Connect DC wiring Note correct alignment Insert the connectors completely until you of connector hear the click Caution ik il su NS SULL SZ ne Note that PSU accepts voltages Ensure fixture is properly between 95V and 240VAC grounded www goenergyeffective com Page 4 GOs IR Sensors Check the location of the IR sensor reception area Place IR sensor with its reception area face dow
4. Energy Effective Lighting GO FLL Planar Lighting User Manual www goenergyeffective com GOs About GO FLL Flat LED Lighting Energy amp maintenance savings Electrical savings of 20 or more compared to traditional fluorescent sets with equivalent light output Low heat generation maximum 47 C Added cost savings on cleaning and dusting as there are no louvers or other dust catching reflectors or lights Energy effective lighting for up to 50 000 hours Difference in effective light depends on the length of time the lights are consistently running e g off at night vs 24 hour operation Most fluorescent tubes have a rated life of 20 000 hours and require re lamping up to 4 times during this same period No ultraviolet radiation EMI flickering or temperature patches Will not affect those sensitive to UV will not fade carpets pictures or turn photo sensitive eyeglasses dark No electromagnetic interference unlike fluorescents and compact fluorescents GO FLL eliminates eye strain headaches and other workplace complaints associated with fluorescent light flickering With no cold or warm spots light and dark areas GO FLL provides a very high uniformity of light across the entire illumination Surface Environmentally friendly Contains no Lead Pb Mercury Hg and Cadmium Cd no hazardous disposal requirements Fully recyclable True Planar Lighting GO FLL is
5. O6 to the top part of IKO6 assemble the top and bottom part of IK06 Drawing of completed product using IKO6 www goenergyeffective com Page 23 GOs IKO7 Installation Pendant for Frame 02 for Frame 01 for ceiling Assembled with PSU light module ceiling Final product www goenergyeffective com Page 24 G 9 Side view Sl ie _____Ii t T tal 1 Make opening on the ceiling with a size of 80 x 350mm 3 Attach pendant bracket to the 2 Fasten support bars to the ceiling to hold a weight of 6Kg FLL module as shown 4 After attaching the PSU 5 Connect PSU to FLL Module 6 Connect Frame 01 to the FLL module to the Frame 02 fasten using provided DC cable using support wires See IKO5 for Frame 02 to the support then fasten Frame 01 to directions bar Frame 02 Suspension wire a DC cable a IR sensor position BL EHS EJ ERN IA al 9 meme em e 0g 0 SS uI DI Top view www goenergyeffective com Page 25 Frame 02 Frame 01 With PSU attached Ceiling assembly with PSU Pendant attached to module www goenergyeffective com Page 26 GOs C series installation Trim ring gt 6 pre drilled holes After Assembly Back Front www goenergyeffective com Page 27 9 GO 1 Cut an opening 380mm x 380mm 2 Fasten support bars to the ceiling with 4 screws to hold a we
6. between the remote control and the IR sensor For maximum distance detach the IR sensor from the GO FLL unit and place it external to the fixture ensuring that the IR sensor does not make contact with the metal N The multi zone remote control is to be used for fixed colour installations only For E ergonomic installations use the single zone remote control only 1 See page 9 for zone switch settings 2 For individual up to six zone switch settings press the appropriate button 1 6 3 To control all zones simultaneously press ALL key 2 4 Individual zones or ALL can be controlled using Power key 1 5 For dimming effect use UP and DOWN arrow keys 4 and 5 1 Push the arrow and place the lid onto the case SONY 2 Insert 2 AAA sized batteries checking anode and cathode correctly 3 Cover the lid pushing the arrow www goenergyeffective com Page 8 GOs Multi zone Setup Schematic diagram of the network using ROG as a typical example CH1 lt Master 1 gt CH2 lt Master 2 gt CH6 lt Master 6 gt ens lt Slave 1 gt lt Slave 1 gt LD lt Slave 1 gt lt Slave 2 gt lt Slave 2 gt lt Slave 2 gt lt Slave 3 gt lt Slave 4 gt lt Slave 3 gt lt Slave 4 gt lt Slave 3 gt lt Slave 4 gt Dips w_ Item swi sw2 sw3 Remark www goenergyeffective com Master 1 Master 2 Master 3 Master 4 Master 5
7. e ceiling 3 Attach part D to part C 4 points pendant part C to the ceiling by using screw M4x26 4 Attach A to B as shown above 5 Adjust wire length to level FLL module NOTE Use appropriate mounting hardware to ensure the weight of FLL module is properly secured and supported www goenergyeffective com Page 19 GOs IKO5B Installation Wire pendant Wire pendant 1 Secure wire pendant for the light module the FLL module for the ceiling to the frame of the FLL 2 Securely fasten the upper part of the ceiling 3 Attach part D to part C 4 points pendant part C to the ceiling by using screw M4x26 4 Adjust wire length to level FLL module NOTE Use appropriate mounting hardware to ensure the weight of FLL module is properly secured and supported www goenergyeffective com Page 20 G QO IS IKO5B installed on module www goenergyeffective com Page 21 GOs IK06 Installation 3D view Back view Front view Side view 3D view Top view Bottom view 3D view Side view www goenergyeffective com Page 22 1 Mark the outline of the fixture and drill the holes on the marked line as shown above Fasten the bottom part of IKO6 to the ceiling as shown in above drawing by using the straight screw 2 Insert top part of IKO6 to the GO FLL module 3 Assemble the bottom part 4 Use M5 set screw to of IK
8. et Hold for 2 seconds to reset all R selections to factory set up Push it then select the button you want to make the default selection 0 M Memory Use buttons to adjust colour and brightness Push M then push a preset button your settings are saved q e Left Right buttons Control colour temperature Left button is to lower temperature warm white Right button is to raise colour temperature cool white a gt Up Down buttons Control brightness o Up makes it brighter Down makes it darker Presets Daylight Preset o Preset Warm Preset e Night Light Preset 50 Brightness Max Brightness o ED Kd Note 1 All settings will be saved if the unit is turned off with the remote control but will return to factory presets in the event of AC power interruption 2 Normal range remote to IR sensor is 10M 30ft but can be affected by sensor position and any obstacles in between 3 This remote control is for use with single zone ergonomic E installations only For all others use the multi zone remote control described on page 8 www goenergyeffective com Page 7 GOs Multi zone Remote Control 1 Power ON OFF key 2 Zone ALL ON OFF key 3 Zone selection keys 1 6 4 Dimming Up key 5 Dimming Down key Ig eee Notes Normal range from the remote control to the IR sensor is 12m 40 ft but the range can be affected by sensor position and any obstacles
9. fective com Page 29 Thank you for choosing GO Lighting Technologies Inc for all of your energy effective lighting needs We appreciate your business 258 Galaxy Blvd Toronto ON M9W 5R8 CANADA Tel 416 679 0259 866 571 7036 North America Toll Free Fax 416 679 9452 www goenergyeffective com D014 ver 20080110
10. ight of 6 3 kg Screws Bottom view Turn the trim until you hear a click Attach trim Counterclockwise Remove trim Clockwise www goenergyeffective com Page 28 GOs Troubleshooting Please refer to the following chart before calling for service Check Points FLL does not turn on Check AC power line connections verify circuit breaker and local switch iS On Remote control does not Check batteries inside the remote control polarity of batteries work Check if FLL is turned on or off Check location of IR sensor s and connection Network does not work Check Dip switch settings Check IR sensor connection to master is properly aligned Check connection of network cables FLL Light is flickering Turn off the AC power and turn on again in 3 minutes If problem persists call GO Lighting Technologies technical support Please request service if the troubles persist after you followed the above checkpoints Please do not dismantle the products yourself they may cause electric shock Please have the following information ready when you call for service Model name Name and telephone number of GO authorized dealer Date of purchase Your name address telephone number Detailed description of the problem symptoms Contact GO Lighting Technologies Inc North America Toll free 1 866 571 7036 416 679 0259 or fax 416 679 9452 www goenergyef
11. ive com Page 16 1 Make an opening on the ceiling as shown 2 Drill a 4 2mm_ hole in the centre of frame as above to accommodate PSU shown above 3 Mark the ceiling to match the drilled holes on the FLL frame 4 Drill pilot holes 2 5mm 3mm on the ceiling NEL 30mm Bit B34 Small Philips 5 Use the screws to secure the FLL module to the ceiling Do not over torque Ensure screws are securely anchored 6 After securing the FLL module to the ceiling cover the screw head with IKO3 cap www goenergyeffective com Page 17 PEPPERS NN __ 107 267 1 Make an opening on the ceiling as shown above to accommodate PSU 2 Drill a 4 2mm_ hole in the centre of frame as shown above 3 Mark the ceiling to match the drilled holes on the FLL frame 4 Drill pilot holes 2 5mm 3mm on the ceiling Se 75mm bo 3 Omm Bit B34 Small Philips 5 Use the screws to secure the FLL module to the ceiling Do not over torque Ensure screws are securely anchored 6 After securing the FLL module to the ceiling cover the screw head with IKO3 cap www goenergyeffective com Page 18 GOs IKO5A Installation Wire pendant for Wire pendant 1 After unfastening one bolt from L shaped bracket in the FLL module for the ceiling each corner fix part A by using M4 10mm flat head screw 2 Securely fasten the upper part of th
12. nward to the fixture To maximize IR sensitivity place IR sensor outside the fixture Install PSU onto the fixtures firmly PSU installed onto fixture PSU may be installed ata distance from the light unit by using a DC extension cable PSU can be installed either onto the fixtures or with some distance to the fixture like above figures Do not use excessive force during installation www goenergyeffective com Page 5 GOL PSU Power Supply Unit RJ11 Connector for IR Sensor Dip S W Network Connection Here Ta AS gt Connector to FLL Factory setup for dip switch of the PSU is 1 1 1 For wire connection between PSU and FLL refer to page 4 Connecting Network Connect IR sensor to the PSU assigned as Master Do not connect to the slaves Set up dip switch per page 9 for assigning Master s pei lt Master gt lt Slave gt lt Slave gt lt Slave gt lt Slave gt lt Slave gt OUT Note On Off switch of each zone must be connected to the same line Example of setting channels Assign one PSU as master per channel and assign the rest of PSU as slaves per channel Per channel assign master like Master 1 001 refer to page 9 Master 2 010 Master 3 O11 Check On Off and dimming function per channel by the remote control www goenergyeffective com Page 6 GOs Single Zone Remote Control o Power On Off R Res
Download Pdf Manuals
Related Search