8000004 Rev 1 EZ-GO quick install guide.pub
Contents
1. ZY EZ Go High Performance Outdoor 802 11bg Bridge Router TEE e Achieve up to 15 Mbit sec data thruput Long Distance operation with good line of sight 2 Best security available WPAZ2 Field Proven Wireless Technology Antenna Pattern STOP DANGER Avoid Powerlines IIH You Can Be Killed When following the instructions in this guide to install the EZ2 take ex treme care to avoid contact with overhead power lines lights and power circuits Contact with power lines lights or power circuits may be fatal We recommend to install EZ2 no closer than 20 feet to any power lines Safety For your own protection follow these safety rules 2 Perform as many functions as possible on the ground 2 Do not attempt to install the antenna on a rainy windy or snowy day or if there is ice or snow accumulation at the install site or if the site is wet o Make sure there are no people pets etc below when you are working on a roof or ladder o Watch out for any power lines which may be overhead under ground or behind walls keeping safely clear of them with the antenna ladders or any tools co See appendix for FCC RF exposure guidelines Recommended Tools Pliers Screws and screwdriver if X mounting to a wall NOTE You should be familiar with using tools such as these before attempting installation of EZ Go You should be comfortable with working on a ladder A GROUNDING Local buildi2. g F 30 to 50 Deg C Humidity O to 100 RH Wind Loading 125MPH survivability 100MPH 23lbs 125MPH 35lbs FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter Limited Warranty All e zy net products are supplied with a limited 12 month warranty which covers material and workmanship defects This warranty does not cover the following a Parts requiring replacement due to improper installation misuse poor site conditions faulty power etc a Lightning damage a Physical damage to the external amp internal parts a Products that have been opened altered or defaced a Water damage for units that were not sealed or mounted according to user manual a Units that were not properly grounded 2 Usage other than in accordance with instructions and the normal intended use Do not return any products until you receive a Return Material Authori zation RMA number Products received without a valid RMA number will be rejected and returned to sender Warranty Repairs All returns must have a valid RMA number written clearly on the outside of the box Without an RMA number the shipment will be refused For customer
3. hat to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help e FCC Caution Any changes or modifications not expressly ap proved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is sub ject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Tech n Ca Sp eci Fi Ca t Ons Note Subject to Change Without Notice Standards 802 11b g WLAN 802 3 802 3u LAN b DSSS DBPSK DQPSK CCK g OFDM 64QAM 16QAM QPSK BPSK Certifications FCC CE Operating Frequency 2400 to 2497MHz USA Canada 11 Japan 14 France 4 Channels Europe 13 Available Transmit Power 802 11b 100 150 200 250mW software selectable 802 11g 50 100mW See 802 11g 73 2dBm 54Mbps Receive Sensitivity 11Mbps 802 11b 84 2dBm 11Mbps 64 128bit WEP WPA WPA2 Remote Config Web Based By IP Address thru Wireless or Ethernet Modulation 14 a6 Antenna Beamwidth V amp H 35 deg Antenna Front to Back gt 20dB INPUT 100 240VAC 50 60Hz OUT Power Over Ethernet Injector PUT 18VDC 0 8A 12 4 x 7 3 x 2 5 314 x 187x 65mm Mount Pole up to 2 dia Mount Operating Temperature 22 to 122 De
4. inside the enclosure to prevent damage from elec trical storms Make sure that the POE Power Supply is plugged into a surge protected outlet such as a surge protected power strip or UPS inside the house 5 PAINTING The EZ Go unit can be painted to match a particular house color Only non metallic enamel or latex paints should be used If a paint with metal content is used it will block the microwaves and cause reduced performance Appendix Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from t
5. n HTML management system built into every EZ Go unit which is accessed thru a standard web browser The unit can communi cate thru the CAT5 ethernet cable connection or thru the wireless con nection so you can manage remote units from a single location 2 IP ADDRESS Default IP address for the EZ Go is 192 168 1 1 To access the EZ Go your computer IP address must be on the same subnet ie 192 168 1 xxx TECH TIP Download the EZ Discovery Tool from http www e zy net support 2plus Utility This tool will assist you in finding the EZ Go on the network and allow you to change the IP address or set it as a DHCP client Just select the unit click on IP DETAILS make se lections and save changes directly to the device 3 SECURITY The following security changes are recommended a PASSWORD Change the user name and password by go ing to SYSTEM PASSWORDS and setting the first user name and password The default is no user name or password for ease of system setup b ENCRYPTION Set an encryption type and key We recom mend WPA2 because it is most secure but if this install is as a client the encryption type and key must match the Access Point 6 SITE SURVEY The site survey is a very useful tool to determine what wireless devices are within range of your EZ Go and could be a source of interference that could cause degraded performance Go to WIRELESS and then click on SITE SURVEY then REFRESH The list will sh
6. ng and electrical codes require that the antenna be properly grounded Improper installation may seriously damage the equipment or building as well as cause in jury or death to you Run a ground wire 10AWG or bigger from mounting bracket of antenna to a good earth ground Cold water pipe or metal stake in ground Qwik Install STEP 1 Choose a mounting location with good line of sight to the re mote location The supplied bracket can be mounted to a wall or to an existing pole up to 2 diameter If only short distances are needed the antenna can be mounted inside a building Sw TECH TIP Microwaves travel in straight lines and they lose gt strength quickly when going thru buildings and trees If there are objects in the microwave path then useable distance will be reduced If the target unit is less than 1 mile away then you won t have to worry too 2 much about a couple obstructions but if over 1 mile and there are some obstructions in the microwave path then the performance will be re duced STEP 2 Mount the Bracket To mount to a wall The supplied u bolt is not used and the bracket is screwed directly to a wall using customer supplied screws To mount to a pole Use the supplied U Bolt and wing nuts Make sure to use a lock washer at each wing nut Tighten wing nuts evenly by hand Use pliers if additional tight ness is needed STEP 3 Mount the antenna housing to the bracket Put the hex head bolt thru the ho
7. ow all wireless devices including channel MAC Address and relative signal strength of all the devices within the range of the EZ Go 7 FACTORY DEFAULTS If at any time the system stops working be cause of changes made to the settings you can get back to the original settings by resetting to factory defaults Go to ADMIN SAVE RELOAD SETTINGS then Reset Settings To Default Any customized settings will be lost once this process is initiated 8 UPGRADE FIRMWARE For the latest firmware point your browser to http www e zy net support 2plus Firmware Download the latest firmware to your PC Select UPGRADE from the menu and then browse for the new file Advanced Features The EZ Go has many advanced features if more functionality is de sired To access the advanced features click on Advanced Web at the top of the menu tree This will activate the advanced menu options The EZ Go can operate as Access Point Client WDS AP WDS Point to Point Go to WIRELESS BASIC SETTINGS to change wire less mode Go to ETHERNET IP SETTINGS to change network op eration mode from Bridge default to Router Since documentation for these advanced modes is too extensive to cover here please retrieve the documentation online at http Awww e zy net support 2plus Documentation TECH CORNER Additional Information you may find useful 1 RAIN SNOW ICE The 2 4GHz frequency being used by the EZ Go will not be affected by hea
8. s located in United States and Canada customer pays all shipping charges incurred to ship the product to E ZY NET E ZY NET pays shipping charges to return the product to the original pur chaser For all other countries the original purchaser shall pay all ship ping broker fees duties and taxes incurred in shipping products to and from E ZY NET Provided the goods have not been modified or repair attempted by someone other than E ZY NET at the option of E ZY NET products may be returned either as repaired or replaced If it is determined that there is no fault found NFF on a unit within warranty the customer will be charged 75 USD for testing time For products out of warranty the standard NFF charge is 200 This charge will be at the discretion of E ZY NET The RMA number is valid for 14 days from date of issue The product must be received by the repair depot within these 14 days or the shipment may be refused Shipping and Damage Claims All shipping damage claims are the purchaser s responsibility Inspect each shipment upon delivery and IMMEDIATELY report all damage to the carrier There may be time limits and inspections may be required 8000004 Rev 2 EZ Go Qwik Install Guide 8
9. using back fin Put the star lock washer so it is be tween plastic housing and metal bracket Install wing nut with lock washer Adjust desired tilt an gle and tighten wing nut Use pliers if additional tightness is needed X TECH TIP Because of the specially designed wide beamwidth an tenna pointing is not critical and simply pointing in the general di rection of the receiving antenna will yield great results STEP 4 Remove the antenna bottom cover by using a coin or house key or screwdriver to push in one of the side snaps and then remove the cover STEP 5 Route a CAT5 cable through the bottom cover and plug into the RJ45 Jack inside the unit Keep the black gasket ma terial in the bottom of the cover to help keep out dust and insects STEP 6 Route CAT5 cable from the EZ Go into the building Always create a strain relief near r the antenna so the cable is not pulling directly on the an mai tenna Use the CAT5 strain relief hook feature built into the housing back fin The Ethernet spec allows for a maxi lt u mum cable length of 100 meters or about 328 feet STEP 7 Install the RJ45 connector on the POE Inserter to the router switch or computer Attach the CAT5 cable from the antenna to the RJ45 output port of the POE Inserter 3 Insert power supply DC plug to the POE Inserter DC Jack Plug the power supply into a surge protected AC power source to power up the EZ Go Software Settings 1 There is a
10. vy rain or falling snow You should not see any performance degradation due to inclement weather If snow or ice collects on the front of the antenna you may see some reduced per formance assuming you are shooting a long distance gt 3miles and the ice or snow buildup is greater than 1 thick on the surface of the an tenna For this reason we suggest mounting under an eave of a house if feasible for your particular situation 2 SUN AND HEAT The EZ Go is constructed of all UV protected materials so it will survive for many years in the most extreme of solar environments ie an Arizona rooftop during the summer The unit has been tested and qualified for constant operation at over 122 deg F am bient temperature Even though the EZ Go is designed for long term survivability in extreme environments we would still recommend that the unit be mounted in a more protected location like under a roof eve if possible Of course if line of sight is better with the antenna mounted in a non protected environment then we would recommend the better line of sight mounting location 3 LIGHTNING Lightning is the single worst enemy of outdoor elec tronics equipment No electronics will survive a direct strike but there are close proximity strikes that can cause huge electrical fields to be generated which can damage electronic equipment We have taken special care in the design of the EZ Go unit to ensure proper ground ing of the electronics
Download Pdf Manuals
Related Search