myon RFTD r3 - Manual - R02 - EN
Contents
1. RO2 EN odt Page 7 of 16 2 1 3 Power supply for receiving unit Wall power supply for receiving unit Power supply plug for receiving unit Mechanical reverse voltage protection 2 1 4 Charging unit for transmitting units Wall power supply for charging unit Charging unit USB hub Micro USB charging cable for transmitting unit Transmitting unit 12 18 2009 17 11 myon RFTD r3 Manual RO2 EN odt Page 8 of 16 2 2 Illustrations of sensor modules 2 21 Connection of sensor adapter cables to transmitter unit all product series On the long side of the trapezoid connector on one side there are two small hooks A l For the correct insertion these must face downwards When disconnecting the sensor adapter cable please do not pull on the sensor cable but the connector housing 12 18 2009 17 11 myon RFTD r3 Manual RO2 EN odt Page 9 of 16 3 Operation The device is not explosion proof Danger of explosion Do not operate in flammable atmosphere When operating for the first time make sure all devices are separated from the electricity grid 3 1 Unpacking the device Remove the device and accessories from the box and check the completeness of the delivery The scope of delivery is dependent on the model series and the model type supplied If you suspect that parts are missing please contact your sales representative 3 2 Preparing the device 3 21 Placement and installation of cable connecti2. 6 1 2 Description of interfaces The interface layout can differ from the ones presented below in RFTD systems that have been specifically adapted to your needs In this case you may contact your sales agency or the manufacturer for further assistance Please have your serial number ready 6 1 2 1 Model series RFTD Exx The analog output is provided via a female DSUB25 socket For the numbering of the individual pins please refer to the following figures S42 40 7 8 COS ob oboLOSS 1 16 Signal of transm module 1 16 AXXXXXXXXXX VY gt 25 GND 43291 Pin No Signal 25 24 23 22 24 20 19 18 17 16 15 14 Female DSub25 socket View from outside into the socket 6 1 2 2 Model series RFTD Axx The analog output is provided via a female DSUB25 socket For the numbering of the individual pins please refer to the following figures T 13 45 11 10 9 8 5 43291 Pin No Signal 6066000000000 0 OO O00 OF 8 OF 17 24 Signal of transm module 17 24 25 GND 25 24 23 22 24 20 19 18 17 16 15 14 Female DSub25 socket View from outside into the socket 6 1 2 3 Pin assignment for DSub25 connector The pin assignment of the DSub25 connector is shown in the following figure Olofororololololororerers SOOO EE Male DSub25 connector View from outside into connector 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 15 of 16 6 2 Disposal o
3. Fehler Referenz nicht gefunden to c until all transmitting units are com 12 18 2009 17 11 Page 10 of 16 myon RFTD r3 Manual RO2 EN odt pletely re charged Depending on the charge condition of the battery the re charging process can take between 30 and 60 minutes When the battery is charged for the first time the charging process may take a little longer All transmitting modules are equipped with newest generation LiPo batteries that do not suffer the problem of memory effect common to older batteries Therefore the transmitting modules can be recharged anytime regardless of their current charge condition without reducing the performance of the battery 3 3 Conduction of measurements 3 3 1 Establishing a wireless connection a To establish a wireless connection between transmitting modules and receiving module just de tach the charging cables from the respective transmitting modules b By this procedure the transmitting unit is being activated and after 1 4 seconds the blue indicat or LED will start flashing The time between each LED flash gives you an idea of how much charge is left in the battery The faster the LED flashes the less charge is left 3 3 2 Capturing and transmission of sensor signal With the steps listed in chapter 3 3 1 the wireless connection is established and the device is ready to Start measuring 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 11 of 16 4 Turning of
4. A AE A a 13 6 Technical descriptio M rsrsr rennt aaa aa AAR 14 SpE el gla tere tar lg emer mer a E a a E terre rer te 14 Bele GONE ral techmital Gael sosedo a a 14 61 2 DESEMALIONNOT IMLCINACES 6 ib fea dicude sis sosatheddinetesnsadeindenciniabweee sks wvendan sa dactnum wana dites 15 6 2 Disposal of product packaging ANd ACCESSOFIOS cccccceccsssseeeeeeeseeeeeeeeeeesseeeeeeeeesseeeeenaees 16 B25 MOUMIESIIGOO LING cinescopio a a eigen 16 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 5 of 16 1 Preface 1 1 Proper use The product is designed to capture and wirelessly transmit different sensor signals such as electromyo grams accelerations forces temperatures pressures etc using a number of transmission units trans mitting to a receiving unit All product models and types of the product may unless expressly stated otherwise only be used extern ally and noninvasively Only the supplied components sensors power supply etc are to be used Addi tional sensors or Spare parts are available upon request from the manufacturer 1 1 1 Products series RFTD Exx The models RFTD Exx e g RFTD E08 RFTD E16 are designed for capturing and wireless transmission of electrical signals electromyograms resulting from the contraction of muscles by means of bipolar elec trodes applied on the skin surface over the muscle of interest 11 2 Products series RFTD Axx The models RFTD Axx e g RFTD A01 DO2 RFT
5. D are designed to capture and wirelessly transmit data of any sensor type e g accelerometers that has a digital interface with compatible communication pro tocol and power supply where applicable The currently available sensor types for the series RFTD Axx can be requested from the manufacturer 1 2 Contraindications Contraindications that relate directly to the product are currently unknown The medical practitioner or user needs to decide on the basis of the general condition of the patient or subject whether or not the in tended application can take place Further information is accessible in current literature 1 3 Possible combinations In addition to these instructions the instructions of those products used in combination must also be ob served Potential electromagnetic or other interference that occurs between the product and other products may lead to disturbances or malfunctions 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 6 of 16 2 Illustrations The images shown below do not claim to be true to scale 2 1 Illustrations of the myon RFTD 211 Receiving unit Product label with serial number Sub D 25 socket for analogue output signals Socket for wall power supply with mechanical reverse voltage protection 2 1 2 Transmitting unit Product label with channel number LED indicator Micro USB socket for connection of sensors and charging cables 12 18 2009 17 11 myon RFTD r3 Manual
6. e er eee ee ee er 6 bS POSSibIEComMDINaAON Susain AAA 6 AMMUST MONS sore a a aa enieamsin inate 7 2A l strations ofr the myom RFID iiacoiciatcienissntsiontatitutosusiatalontaantaleepsantelouiaiintaeauitatuoniiniouneratubenainaiay 7 2T V RECON MING UNG istersticeselontetsseihen tines tl ontets aN tinea tl E a Ea EEE aAA EEA 7 Z2 Tra SMITE UPI eini ea a 7 21 3 Powersupply TOr RECEIVING UM eiiie ia e E 8 2 1 4 Charging unit for transmitting unitS s sssessrisesrrrrrssrrrrsrrrrnsrrrrnsrrrrrrrrrrnsrrrrrrrrrrrererne 8 2 2 Illustrations Of sensor Modules sonnn a A eed 9 2 2 1 Connection of sensor adapter cables to transmitter unit all product series 0068 9 Sa o 2 q 0 anne reer a ee en eer ee eee ere ere arr 10 SUMP aACMING TNE devi Eines a a idee lee Lette 10 3 2 P re Panne Line BG VIC Ecran a A ouanasecneuns cavananeee sans cbuacaiee aaiatesnasee 10 3 2 1 Placement and installation of cable connectionS ssesssssssesssrrrsressrrrrrresrrrrrresssssseens 10 3 2 2 Re charging of the transmitting unitS sesssrrsseessrrrrressrrrrrnesrrrrrnessrrrrnerrrrrrerrrerre 10 33 Conduction OF ME ASUNEMEN CS xsjcccisiavinrsines vines EAE ATRAE AEE 11 3 3 1 Establishing a wireless CONNECTION ee eenr nn eeeeeeas 11 3 3 2 Capturing and transmission Of sensor signal sssssssssssrrssessrrrrrressrrrrnessrrrrrnessrrrererre 11 A TUAPMIS OFT the deVIi CE aisse a a a N r raa EET CNR 12 SCHECK S ronca
7. f product packaging and accessories In order to dispose of the product packaging and or accessories the existing country specific regulations and laws must be respected More information may be requested from the manufacturer of the product 6 3 Troubleshooting No Symptom Solution 1 Blue indicator LED on the transmitting module is not flashing If after a full re charge cycle the blue indicator light is on continuously the LED indicator is not flashing after removal of the transmitter module from the charging unit please plug the transmitter module back into the charger wait a minute and detach the charger again 2 One several blue Please separate the receiving unit from the mains by pulling the power indicator LEDs onthe adapter out for about one minute Then plug the power adapter into the receiving unit do not power outlet again flash blink even though the channel modules do flash correctly In addition on some transmission channels only a sine wave with large amplitude profile is visible 3 On one or more This is an intended process provided for the visualization of transmission transmission channels errors If the wireless connection between one several transmitting there is no sensor modules and the receiving unit is broken e g because of battery drainage signal visible but only a or because the distance between the transmitting module and receiving sine wave profile with uni
8. f the device To turn off the device please switch off all interacting devices and disconnect all devices from the mains Unplug the wall power supply for the charging unit and for the receiving unit from the power outlet If the transmitting modules are connected via the charging cable to the charging unit these are alSo automatically switched off Otherwise the transmitter modules will keep transmitting until their battery capacity is exhausted Disconnect the cables between the device and other interacting devices e g Vicon motion capture systems 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 12 of 16 S Checks Please follow the suggested checks before each use of the device e Check the instrument for potential damage and completeness If you notice any damage do not use the device and contact your sales agency or the manufacturer e Check all connecting cables and accessories for damage If you notice any damage do not use the device and contact your sales agency or the manufacturer e Avoid excessive bending and stretching when positioning the cables and make sure that the cables never pose a tripping hazard e Check all connectors fit properly e Check that all connection contacts are clean e Check that the labels are complete and legible 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 13 of 16 6 Technical description 6 1 Technical data 6 1 1 General technical data Receivin
9. g unit Transmitting unit Manufacturer myon AG Baar Switzerland Model series RFTD E RFTD A Types RFTD E04 RFTD E08 RFTD E16 RFTD E32 RFTD A01 RFTD AO2 Radio Frequency Transmitting Devices Operating voltage 220 V 50 Hz Operation via built in external wall power battery supply Power consumption 800 mA 23mA during transmission Properties Weight 340 g 19g Housing color blue Dimensions 194 x 114 x 59 mm 40 x 40 x 15 mm Inputs outputs 25 Pin Sub D socket power supply socket Micro USB socket Sampling rate N A 4000 Hz adjustable Resolution 14 bit 12 bit Bandwidth S 1000 Hz adjustable Range N A up to 30m Transmission protocol 2 4 GHz proprietary Battery life N A up to 8 hours Battery re charging time N A 30 60 min Latency 16 ms fixed Inter channel offset none Included accessories Wall power supplies N A charging unit s charging cables sensors model series RFTD A only sensor adapter cable 25 Pin D Sub connector open ends Environment Operation 5 40 C 20 90 humidity Storage 20 60 C 10 90 humidity Certifications ED 199915 EC R amp TTE ED 1993 42 CE 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 14 of 16 The corresponding EC Declaration of Conformity can be obtained free of charge by the manufacturer
10. lth the functioning of the device or the safety of your data if not adhered to indicates additional information and tips indicates a step you will need to carry out Quotation marks indicate names of chapters and terms that should be emphasized talics font identifies file names and menu items This font indicates screen outputs 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 3 of 16 Important Information Please follow these safety instructions to ensure your safety and the optimal functioning of the device The product may be used only as intended and in compliance with the instructions by appropriately trained and qualified personnel Maintenance and repairs have to be carried out by the manufacturer or authorized personnel The product may only be used in combination with accessories and spare parts that are specified in the manual or by other means by the manufacturer Other combinations accessories and consumable parts may only be used if they are specifically designed for the intended application and do not affect perform ance and security requirements Safety instructions regarding power supply e The device is disconnected by pulling the power plug from the power outlet e The power cord in devices with mains plugs is used for separation from the mains The power out let must be located in the vicinity of the device and must be easily accessible e This device ma
11. myon SIMPLY WIRELESS Radio Frequency Transmitting Devices Models RFTD Exx RFTD Axx User Manual Copyright Copyright 2009 myon AG All rights reserved This publication may not without the prior written permission of myon AG be reproduced in any form or by electronic mechanical magnetic optical chemical manual or other means transmitted transcribed stored in a retrieval system or translated into any language or computer language Disclaimer myon AG does neither directly nor indirectly guarantee the accuracy of this manual and specifically dis claims any warranties as to the quality or fitness for a particular purpose Furthermore myon AG reserves the right to revise this publication without notice and to make changes to the content Technical changes reserved As a result of further technical development illustrations and technical data may differ 12 18 2009 17 11 Page 2 of 16 myon RFTD r3 Manual RO2 EN odt Introduction In this manual you will find important information needed for the commissioning and operation of the device Always adhere to the safety instructions in the manual of your computer or other systems involved and the ones in this handbook If you experience any problems please contact your sales agency or the re spective manufacturer Conventions used in this text Throughout this manual the following conventions are used indicates important information that may damage your hea
12. ons a Place the receiving unit on a flat surface b Plug the power connector for the receiving unit into the power socket on the receiving unit c Connect the socket for analog output signals to your specific recording system e g Vicon Please make sure you chose the correct assignment of the individual pins see chapter 6 1 2 Description of interfaces on page 15 For the preparation of this interface specific technical knowledge may be required If you do not have the necessary skills please consider consulting an expert For this connection a specifically adaptor cable may be required d Plug the power adapter of the receiving unit into a power outlet e Turn on your specific recording system e g Vicon as well as all other interacting systems e g force plates etc 3 2 2 Re charging of the transmitting units a Connect the wall power supply for the charging unit to the charging unit b Plug the wall power supply for the charging unit into a power outlet The control LED of the char ging unit will light up c Plug one end of the included micro USB charging cables into one of the transmitting units and the other end into a free USB port of the charging unit USB hub d After a short time the blue indicator LED of the transmitting unit will light up shortly indicating the beginning of the re charging process The re charging process is completed when the blue in dicator LED lights up continuously e Please repeat steps
13. t is too large the receiving unit will output a 400 Hz sine signal on the large amplitude affected channels Solution e re charge the transmitting modules e reduce the distance between transmitters and receivers e temporarily switch off any wireless LAN and or Bluetooth devices in the vicinity of the measurement system and check whether this has any effect on the signals measured 4 Strong noise humon_ Check that all interacting systems laptops Vicon etc are connected one multiple channels particularly applies to model series RFTD Exx correctly to their earthing of the mains Model series RFTD Exx Ensure optimum connection of the EMG electrodes Make sure that you are using fresh electrodes from a newly opened package and that their date of expiry is not exceeded 12 18 2009 17 11 myon RFTD r3 Manual RO2 EN odt Page 16 of 16
14. y only be operated on a power grid in conformity with the specifications indicated on the device s label or mark tor in the section Technical data If you are not sure whether these requirements are met please contact the manufacturer or your local power company e The device is not suitable for use outdoors Cleaning and care e Unplug the power cord from the outlet before cleaning the device e The device can be cleaned with a slightly water moistened soft lint free cloth Do not use harsh cleaners aerosol cleaners or glass cleaners e Objects or liquids must not get into the interior of the device e Check the device after each cleaning to its functions and to possibly damage occurred If you notice any damage please do not make any repair attempts but contact your sales agency or the manu facturer Maintenance Do not open or remove the protective housing yourself as you might expose yourself to dangerous voltages and other risks In case of abuse or accident such as dropping the unit or improper use please contact the manufacturer or authorized service personnel for maintenance 12 18 2009 17 11 myon RFTD r3 Manual R02 EN odt Page 4 of 16 Content PETI Gata ah tater ea ettatned S E 6 AP OU GRU SC iistrasdasuaiyvapitn O E E meimanbanunavedien 6 ERI Products sones RETO EXX erien a E increase nan 6 TZ Productssenes Perl Ds OG ranira a sec veeadiacesaeeac tends vaca oe asa 6 LACON a els aeid 9 denen ee ee er
Download Pdf Manuals
Related Search