Home

User Manual

1. 78 4 SONEL KT 640 THERMAL IMAGER Gres 1 Safety Before you proceed to operate the camera acquaint yourself thoroughly with the present manual and observe the safety regulations and specifications defined by the producer Any application that differs from those specified in the present manual may result in a damage to the device and constitute a source of danger for the user The camera must not be used in rooms where special conditions are present e g fire and explosion risk It is forbidden to use damaged or malfunctioning camera and is partially or fully out of order In case the camera is not used for a long time its batteries should be removed It is not allowed to use the camera with half closed or opened battery cover and do not use any other power adapter than the one supplied with the camera Repairs may be carried out only by an authorised service point KT 640 Thermal Imager is designed to measure and record the images in the infrared The camera is constructed in a manner which gives you maximum performance and safe ty at work however the following precautions must be adhered to at all times in addition to any advised precautions applicable at the relevant work site or work area Keep the camera steady during operation Do not use the camera in ambient temperatures exceeding its operation and storage temperature ranges Do not direct the camera toward very high intensity radiation so
2. Israeli US missile test fuels jitters over Syria lt gt Go to the bar in low right corner and select open Network and Sharing Center Troubleshoot problems Open Network and Sharing Center 58 SONEL KT 640 THERMAL IMAGER Select Change adapter settings T gt Control Panel Network and Internet Network and Sharing Center Search Control Panel View your basic network information and set up connections Control Panel Home View your active networks i Access type Internet Change advanced sharin Network VA ada Sind settings Private network our Connections Ethernet Change your networking settings Set up a new connection or network Set up a broadband dial up or VPN connection or set up a router or access point S Troubleshoot problems Diagnose and repair network problems or get troubleshooting information Chose network connection linked to USB Ethernet RNDIS Gadget Search Network Connections 2 T 4e Control Panel Network and Internet Network Connections gt ler Organize Disable this network device Diagnose this connection Rename this connection gt Local Area Connection Ethernet Network 96 Realtek PCle Family Controller 9 2 USB Ethernet RNDIS Gadget Right click on selected network connection and select Properties In Networking tab find and select Internet Protocol Verision 4
3. text and other items larger or smaller Adjust screen resolution How to correct monitor flicker refresh rate In Device Manager wingow find Other Devices with RNDIS Ethernet Gadget in it File Action View Help E Rooster gt Ils Computer gt s Disk drives gt 8 Display adapters gt DVD CD ROM drives gt Human Interface Devices gt IDE ATA ATAPI controllers gt v Keyboards gt P Mice and other pointing devices gt Monitors gt R Network adapters 2 IB Other devices Scan for hardware changes gt wer Ports amp LPT Properties gt Processors gt 3 Sound video and game controllers gt System devices Opens property sheet for the current sele Right click on it and select PropertiesGo to Driver tab and select Update driver Sonel USER MANUAL 53 c USB Ethemet RMDIS Gadget Driver Provider Acer Incorporated Driver Date 1 13 2010 Driver Version 1 0 0 0 Digital Signer Microsoft Windows Hardware Compatibility Publisher To view details about the driver files To update the driver software for this device If the device fails after updating the driver roll back to the previously installed driver Disables the selected device To uninstall the driver Advanced And select an option as below 54 SONEL KT 640 THERMAL IMAGER How do you want to s
4. Browse my computer for driver software Locate and install driver software manually USB Ethernet RNDIS Gadget Properties General Advanced Driver Details K USB Ethernet RNDIS Gadget Driver Provider Acer Incorporated Driver Date 2010 01 13 Driver Version 10 00 Digital Signer Microsoft Windows Hardware Compatibility Publisher Driver Details To view details about the driver files To update the driver software for this device If the device fails after updating the driver roll back to the previously installed driver Disable Disables the selected device To uninstall the driver Advanced Roll Back Driver Uninstal 3 Update Driver Software USB Ethernet RNDIS Gadget Browse for driver software on your computer Search for driver software in this location CAProgram Files x86 RealtelNICDRV 8169win7 Include subfolders gt Let me pick from a list of device drivers my computer This ist wil show installed driver software compatible with the device and all driver software in the same category as the device select Network Adapters and then select producer choose Microsoft Corporation Microsoft in some cases network adapter Remote NDIS Compatible Device i eens ap a 0000 Select Network Adapter K Click the Network Adapter that matches your hardware then click OK If you have an installation
5. f Use the Command Prompt for 3 PC to restore Windows advanced troubleshooting men den System Image Hh Ty Recovery n Change Windows startup behavior a Recover Windows using a specific stem image file M ma T e Automatic Repair Fe problems that keep Windows from hist 50 SONEL KT 640 THERMAL IMAGER 7 select Restart N FB adven wolis io tp t 22 LS pee qnte KS LIT if V en s 1 4 SME LUAR wo A ERG meme h n z gt ptt rc VI T2 YA PETIT Ary l esta Change VVINdGOWS U i 8 In the next window press F7 on keyboard and the system will reboot in the mode al lowing unauthorized drivers installation Proper driver installation Turn on the camera and wait antil self test procedure is completed Connect the camera to computer USB port go to Settings Go to Control Panel USER MANUAL 51 Settings Control Panel Personalization PC info Help 3 Network Unavailable a Q0 Notifications Power Keyboard Change PC settings Depending on the control Panel configuration you can open Device Manager directly or through Hardware and Sound E Control Panel Search Control Panel p Adjust your computer s settings View by Category Gm System and Security User Accounts and Family Safety Review your computer s status Change account
6. er USER MANUAL THERMAL IMAGER KT 640 SONEL S A ul Wokulskiego 11 58 100 Swidnica version 1 1 09 09 2014 KT 640 Thermal Camera complies with current EU directives relating to electromagnetic compatibility and safety Thank you for purchasing our thermal imager KT 640 is a modern easy and safe to use measuring device Please acquaint yourself with the present manual in order to avoid measuring errors and prevent possible problems related to operation of the imager All products of Sonel S A are manufactured in accordance with Quality Management System which is approved to ISO9001 2008 for the design manufacturing and servicing Due the continuous development of our products we reserve the right to introduce changes and im provements in the thermal imaging camera and in the software described in this manual without prior notice Copyrights Sonel S A 2013 All rights reserved This manual may not be copied reproduced translated or transferred to any electronic carriers or in machine readable form in whole or in part without the prior written consent of Sonel S A 2 SONEL KT 640 THERMAL IMAGER Gres TABLE OF CONTENTS 1 MSA BEY 5 2 PREPARING THE CAMERA TO WORK cccccccccccccccccccccccccccccccccees 7 3 FUNCTION BUTTONS JOYSTICK AND ON SCREEN 7 3 1 BUTTONS 7 3 2 VIEWFINDER TOUCH SCREEN T
7. sponding spot within its area When the maximum temperature is selected in analysis settings displayed temperature value for given area is red coloured For average temperature it s black and for minimum it s blue 09 15 24 Real Time Using touch pen area can be moved to any place on the screen Press and hold any point within the area and slide it to a new place on screen To enlarge the area or to change its shape press touch pen against the corner of the area and while keeping it pressed move it and change the areas shape as per your convenience Up to 8 areas can be added on screen 22 SONEL KT 640 THERMAL IMAGER Gre To delete the area select it by pressing pen within the area Green aarows will appear in all corners Then use bin m symbol located on tool bar 7 4 Isotherm analysis Press pen or use Joystick on button available under expandable AnalysisTools icon to initiate isotherm analysis mode This mode is available only for images in real time mode and for frozen images Slide markers on temperature bar to set the temperature range for which isotherm area will be marked with black white or green colour depends on analysis settings see sec tion 8 1 Isotherm temperature range is displayed on the screen at the bottom bar 11 23 08 15 6 8 10 2 O 1x Press button to return to regular infrared image mode 8 Functions and parameters settings Functions and parameters settings can be adjusted
8. Af ter activating or deactivating laser pointer corresponding information is being displayed on screen for 3 seconds NOTE Laser beam may damage eyes in case of direct contact DO NOT LOOK INTO THE LASER BEAM DIRECTLY AND DO NOT DIRECTED THE LASER BEAM TOWARDS OTHER PERSONS OR ANIMALS Special caution should be excercised as the la ser beam may reflect off shiny surfaces Due to safety reasons Laser pointer is available after enabling it in function settings menu see function settings section 8 4 4 10 Image modes KT 640 captures both thermal and visual images Thermal image mode can be switched into visual image mode at any time while being in real time mode or by freezing thermal image on screen button and also during browsing thermal images stored in the memory Press 19 button to swith into visual image mode Press the same button again to return to thermal image mode Displayed image mode can also be changed using touch screen In order to do that ex pand analysis tool bar and selec proper button on touch screen depending on whether the image is in real time mode or it s frozen one Description of analysis tool is located in section 7 p In case of frozen image or browsing thermal images stored in the memory button will switch to visual image to return to thermal image mode In real time image mode press button to put thermal image on top of the visual one with possibility to a
9. Digital Zoom x2 x4 x8 VISUAL Visual Image Video CMOS 640x480 Image Presentation External Display 5 7 touch screen VGA LCD 640x 480 pixels Viewfinder 0 6 OLED 640x 480 pixels Video Output 60Hz VGA 50Hz PAL 60Hz NTSC switchable InfraFusion The combination of infrared and visual image picture in picture with the ability to combine images only for the specific tempera ture range Measurement Temperature Pange Filter 1 20 C 250 C Filter 2 200 C 800 C 2 C or 2 of reading Measurement Modes Auto hot spot amp auto alarm in live zoomed image amp video 8 mov able spots 8 movable amp changeable areas displaying either max min or average vertical amp horizontal line profile histogram amp iso therm in live zoomed frozen saved image amp video Emissivity Correction Variable from 0 01 to 1 00 in 0 01 increment Measurement Featu Automatic correction based on distance relative humidity atmos res pheric transmission and external optics Optics Transmission Auto based on signals from sensors 72 SONEL KT 640 THERMAL IMAGER Gre ee p Classification Type Class 2 semiconductor laser Image Storage Type 16GB SD card max 32GB File Format JPEG An individual file consists of infrared image visual image voice annotation and remarks if any Voice Annotation Up to 60 seconds per file H 264 plik avi storing on SD IRV Format storing on PC hard d
10. SETTINGS cccccccscccccccccccccees 23 8 1 THERMAL IMAGES ANALYSIS PARAMETERS aaa 23 8 2 TARGET PARAMETERS se s 24 8 3 SISTEM SETIINOS M eos sans adi S 25 8 4 IEC EI T I NG sean 26 6 5 RESTORING TO DEFAULT SETTINGS aaa 27 8 6 TOUCH PEN CALIBRATION zs been ss dans 27 8 7 VIDEO RECORIOING assessment nue DM Cr 28 8 8 7 5 28 Gres USER MANUAL 3 6 9 a eee 31 8 10 INFORMATION ON HARDWARE AND FIRMWARE VERSION a 31 811 FIRMWARFEUPD TE esse 31 9 ACCURATE TEMPERATURE MEASUREMENT 32 10 POWER SUPPLY CHARGING 1 6 33 10 Sanss bs de rie uberes een 33 0 22 SATIERY POWER SUPPL 33 10 2 1 Charging batteries m 33 10 3 CHARGING BATTERY IN EXTERNAL BATTERY CHARGER 34 10 4 GENERAL RULES OF USING LITHIUM 0000000000 8 35 11 CAMERA S DRIVER AND SONEL THERMOANALYSE PC INSTALLATION GUIDE sesesesesesesecesscscsesesesesesesesesesesecscscsesesesesesesesesesessssese
11. and go to its Properties USER MANUAL 59 Click OK to accept changes and the connection will be configured properly 60 EP USB EthernetRNDIS Gadget This connection uses the following items dil File and Printer Sharing for Microsoft Networks 1 2 Microsoft Network Adapter Multiplexor Protocol Microsoft LLDP Protocol Driver i Link Layer Topology Discovery Mapper 1 0 Driver 2 Uninstall Desciinlion Transmission Control Protacol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Go to Use following IP address and type fil lit in as below You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 6 Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically 6 Use the following DNS server addresses Preferred DNS server Alternate DNS server validate settings upon exit SONEL KT 640 THERMAL IMAGER 11 4 Sonel ThermoAnalyze Installation Guide Installation procedure is identical on all computers regardless of the operating system It is recommended to close down all applications before installing the program After in serti
12. button until the screen turns off 10 SONEL KT 640 THERMAL IMAGER Gre 4 2 Focus adjustment Focus can be adjusted in manual or in auto mode In manual mode aim the lens at the target and then move the joystick up or down to zoom the focus point in or out For very precise focus setting it is recommended to use the Zoom function To adjust the focus automatically use the 21 button Press it and the camera will focus provided that the object which the camera is being set to focus on has a large thermal contrast In case the auto focus results are dissatisfying use the manual focus mode 4 3 Enlarging image Zoom x2 x4 x8 Moving the Joystick right allows to magnify thermal image 2 4 up to 8 times bigger while moving the Joystick left makes the image zoom out down to its nominal size Zooming can be also performed by pressing the field with the magnification symbol and its ratio on it It is located on the bottom bar on the screen see section 3 3 Image magnification allows accurate focusing It should be remembered that KT 640 sup ports digital zoom only so it is not advisable to save IR thermal images digitally enlarged 4 4 Temperature range Temperature range can be adjusted by buttons or by the use of touch screen when the camera is in the real time mode and when a real time infrared image is being displayed on screen T 0 5 Press 6 button or click on icon or on the temperature value on icon on the tou
13. changes will be performed by processing a thermal image with computer program This value should be changed manually in order to determine proper relation of the examined object temperature and the temperature of cer tain types of surroundings e g the sky snow Adjustment of ambient temperature is described in section 8 2 The influence of distance from the examined object onto the accuracy of measurement can be significant depending on the medium the object is placed in air for smoke etc and its reducing properties related to thermal radiation It is possible to correct the default value 1 8 m within the range of 0 1 30 m The method of adjustment is described in section 8 2 Relative humidity can also influence the accuracy of measurement the default value 70 can be changed to any value within the range of 0 100 this function is described in sec tion 8 2 Additionally to achieve an accurate temperature readout hold the camera stably and adjust focus properly Before capturing the image it is recommended to invoke the auto calibration of the camera by pressing and holding button for seconds see section 3 1 32 SONEL KT 640 THERMAL IMAGER Gre 10 Power supply charging batteries The camera is powered by LiOn battery It can also be powered from mains through AC adapter The battery can be charged while being inside of the camera The device is also supplied with the external battery charger and spar
14. connected via Wi Fi see section 8 8 to learn how to configure the connection or USB description below In both cases the camera driver must be installed 62 SONEL KT 640 THERMAL IMAGER Gre 12 3 Sonel ThermoAnalyze setup NOTE Only some features and functions of Sonel ThermoAnalyze related directly to recording infrared video are described below Detiled description of all features and functions can be found in Sonel ThermoAnalyze user manual Setup option File menu is used to determine the directory in which your videos cap tured sequences images and other parameters related to recording infrared videos will be stored ju Open Image 1 x EX r O Video Report External Device Manager 1 C Users IRO00111 2 C Users IROO0001 3 000005 4 000004 12 jJ 45 5 78 Exit Film Path C Program Files x86 Sonel ThermoAnalyze IR Video Capture Saved Path C Program Files x86 Sonel ThermoAnalyze Capture Capture Image Save as IRI or JPG file only Save as IRI or JPG file and open it Frame Rate 25 s Kinescope Rate Update track view 120 ms Default Palette S ner USER MANUAL 63 Film Path choose the folder where the recorded video files will be saved by default it is set to a IRVideo subfolder at the place where the program is installed Capture Saved Path choose the folder for captured images
15. displayed on screen drop down menu bar expanded analysis toolbar its on screen loca tion can be changed status bar temperature range bar and its corresponding color pal ette and central point with its temperature value Kat 09 15 24 Real Time Additionally above the bottom bar messages of each functions are being displayed e g saving SD card removed Touch screen menu elements and temperature range bar hide after pressing button They show up again after freezing image on screen or after touching the screen 8 SONEL KT 640 THERMAL IMAGER Gre Output signal from the camera can be simultaneously viewed at the same time on a TV screen monitor by using RS232 Video cable socket 13 on the camera in PAL or NTSC depends on the video output settings selected in System Settings menu section 8 3 3 3 On screen information arrangement temperature bar auto A manual M temp range drop down menu temperature X temperature range central point units expandable analysys tools 09 15 24 Real Time OQ 1X Mode real time emissivity coefficient battery frozen memory view emissivity list and power browsing nei zoom flashlight supply indicator real time clock status and switch Bottom bar contains real time clock current mode status real time image frozen image or memory browsing Zoom ratio battery and power supply indicator no SD card infor mation visible only when SD card is missin
16. enclosure powder paste etc During cleaning the camera must be turned off Due to the applied anti reflective coating optical lens are the most sensitive and at the same time the most expensive part of the camera the lens is of key importance to radio metric capabilities of the infrared system Therefore it is important to close the protective lens cover after each use of the camera Optical surfaces should be cleaned only when they are visibly fouled Do not touch exposed surfaces of optical lens with fingers be cause fouling left with fingerprints can be harmful to coatings and glass of the lens Chemical agents must not be used for cleaning the optical viewfinder and particularly op tics and accessories of the camera Use a clean dry and soft cloth for cleaning the body of the viewfinder for cleaning the lens use only the supplied lens cleaning cloth 17 Calibration In order to ensure the accuracy and reliability of the thermal imaging camera it is recom mended to calibrate the instrument once every 12 months For detailed information related to laboratory services call 48 74 85 83 879 or send an inquiry to serwis sonel pl The KT 640 thermal imaging camera does not comprise any parts serviceable by the us er Do not attempt to dismantle or modify the camera on your own Opening the instru ment voids the warranty CAUTION Only manufacturer is entitled to preform service repairs When storing the instrument o
17. limit or click on icon number defining lower range limit to switch into manual adjustment of upper and lower temperature range limits see section 4 4 This operation allows to choose the most optimal temperature ranges right after freezing an image on screen 16 SONEL KT 640 THERMAL IMAGER Gre NOTE Chosen limits values that are set for the captured images and will be used for those images but they will also remain set after returning to real time mode Af ter saving an image switch to automatic temperature selection mode click on emissivity coefficient symbol on icon to change its value for infrared im age by selecting it from the table of materials Click on the value next to symbol to de fine its exact value by pressing touch pen on the value and moving pen up and down in struction on how to change emissivity coefficient values is described in section 4 5 NOTE The value selected for the captured image will also remain active after re turning to real time mode If you want to go back to the previous value you must se lect it again Ay click on icon or press Joystick button to expand analysis tool bar Clicking on indi vidual icon allows to perform the analysis of the whole thermal image or its part detailed description in section 7 E X ii T m lt 1 1 EI NL Frozen O O gi pes Co 4 m F click NV icon to view captured visual image clic
18. tel 48 74 85 83 878 Sales Department 48 74 85 83 879 Service Department fax 48 74 85 83 808 e mail hx sonel pl internet www en sonel pl Manufactured in UE 78 SONEL KT 640 THERMAL IMAGER Gre
19. Frame rate choose the number of images registered per second 25 by default Default Palette set the palette used in video mode Kinescope rate defines the image saving cycle interval e g 1 every frame will be stored 5 every fifth frame will be stored In some situations there is no need to capture all frames Using this option allows to save space on hard drive SD card Update track view frequency of refreshing information for each point 12 4 Recording infrared video in real time Use Device Video tab to get the video output directly from the camera into Sonel ThermoAnalyze program Connect the camera to PC by inserting USB interface into 7 socket The camera should run in real time mode with no menu or command available on screen 4 Sonel ThermoAnalyze Xy File Tools View i Open Image Ctrl O aaa M Setup Open Fim Image Palette ax 8 Report b External Device Manager 1 C Users IRO00111 2 C Users IRO00001 3 000005 4 000004 1234567 Exit Select Device Type Please select the thermal image device type KT640 WIFI Note Switch on the camera and wait until its internal tests are completed before connect ing it to PC Is is advised to connect it before launching Sonel Thermo Analyze program 64 SONEL KT 640 THERMAL IMAGER Gre After Selecting KT 640 and setting proper connection below window
20. Remote settings System protection y Advanced system settings Control Panel Home Windows edition Windows 7 Professional Service Pack 1 yet more features with a new edition of Windows 7 System Rating windows Experienc Intel K Core TM 15 2400 CPU 9 3 10GHz 3 30 GHz Processor Installed memory RAM 8 00 GB System type Pen and Touch Action Center Computer name domain and workgroup settings Windows Update Computer name Performance Information and Full computer name Tools Computer descripbon Copynght 2009 Microsoft Corporation All rights reserved View basic information about your computer 64 bit Operating System No Pen or Touch Input is available for this Display or open it through Control Panel to which you can get access depending on the configu ration directly G c Coe e ua ontrol i v 24 Control Panel All Control Panel Items CC Adjust your computer s Y Action Center gt Backup and Restore ZS Date and Time e Ease of Access Center Fonts Internet Options Location and Other Sensors Notification Area Icons Personalization 42 settings 73 Administrative Tools BA Color Management e Default Programs 4 Devices and Printers Flash Player 32 bit Getting Started amp Java 32 bit J Mouse amp Parental Controls Phone and Modem SONEL KT 640 THERMAL IMAGER V
21. Select temperature value exceeding which will trigger audible alarm This field is active when TempAlarm is set to High or Low 8 2 Target parameters object After selecting main Menu go to section 2 and select with touch pen or Joystick Target tab Analysis Target System Function Default In the dialog box that opens you can set following parameters 24 SONEL KT 640 THERMAL IMAGER Gre Emiss 098 Relhum LLU Distance m BackgroundTemp reve Tamb 93 6 C DewPoint E OK Emiss value of emissivity coefficient of the measured object table with emissivity coef ficient values for different materials is available in section 14 Relhum Relative humidity Distance object s distance from the camera this value is not related with image fo cuse but it allows to correct the influence of the medium in which the radiation propa gates dust mist smoke vapor on the accuracy of the measurements BackgroundTemp background temperature background surrounding the object not the place where the mesurement is made allows you to set the proper relation between ambient temperature and the measured objects and it allows to adjust the temperature reading This feature is useful when measurements are performed from certain distance for example in a location where the ambient temperature is different than the one sur rounding measured object In most cases there is no need for adjusting this value
22. Sync your settings HomeGroup Windows Update 4 goto Troubleshoot I Autocorrect misspelled words On Highlight misspelled words On Language Add or change input methods keyboard layouts and languages Language preferences Available storage You have 12 0 GB available See how much space your apps are using View app sizes Refresh your PC without affecting your files If your PC isn t running well you can refresh it without losing your photos music videos and other personal files Get started Remove everything and reinstall Windows If you want to recycle your PC or start over completely you can reset it to its factory settings Get started Advanced startup Start up from a device or disc such as a USB drive or DVD change Windows startup settings or restore Windows from a system image This will restart your PC Choose an option gt Gre Continue Bat and continue to Windows 8 Troubleshoot Refresh or reset your PC or use advanced tools x Turn off your PC USER MANUAL 49 5 go to advanced options Troubleshoot Refresh your PC IF your isn t running well you can refresh it without losing your files Reset your PC IF you want to remove all of your files you can reset your PC completely Advanced options 6 select Startup settings Advanced options System Restore Use restore point recorded on your AUI
23. Tamb real ambient temperature measured near the converter value measured by sen sor DewPoint Dew point value for the location place measured by the camera s sensors 8 3 System Settings After selecting main Menu go to section 2 and select with touch pen or Joystick Sys tem tab Analysis Target System Function Default In the dialog box following settings can be done Gre USER MANUAL 25 System Setting TempUnit pt FrameAver My Language Engish v VideoOut 10556 v Date Y MD 87 7 120 Time HM S 9 p TempUnit temperature unit selection C or F FrameAver frames averaging parameter that specifies the number of frames used to freeze and store an image in case the nuber is increased above 1 the camera during the process of capturing freezing thermal image uses special denoising algorithm where the image is averaged from a larger number of captured frames 2 4 8 or 16 in case of selecting the parameter s value above 1 it is advised to use tripod as all vibrations caus ing even the slightest movement of the camera result in degrading the sharpness of the image blurred images Language language selection Polish English Chinese VideoOut PAL NTSC or off Date Y M D date setting year month day Time H M S time setting hours minutes seconds 8 4 Function Settings After selecting main Menu go to section 2 and select with t
24. The default wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected Notify me when this connection has limited or no connectivity OK Cancel Internet Protocol TCP IP Properties General fou get F settings assigned automatically if your network supports thie capability Dtherwise you need to ask your network administrator For the appropriate IP settings Obtain an IP address automatically Use the following IF address IP address Subnet mask Default gateway 132 158 2 110 255 255 255 0 132 158 2 2 f Obtain ONS server address automatically Prefered ONS server Alternate DHS server Use the following DNS server addresses Advanced Click OK and the camera is ready to work with Windows XP operating system Oner USER MANUAL 41 11 2 Windows 7 installation guide Turn on the camera and wait antil self test procedure is completed and then connect the camera to USB port on computer Open Device Manager right click on My Computer on desktop and choose its Proper ties from drop down menu Open F Szukaj wirus w Open folder location Manage Map network drive Disconnect network drive Restore previous versions Send to Cut Copy Create shortcut Delete Rename Properties Device Manager
25. ThermoAnalyze Tools View Help Device Video Open Film External Device Manager 1IROOO1S9 Select the camera type KT640 WIFI and in the window below type obtained IP address Connection with computer will be set and the image from the camera will be displayed di rectly in the program in real time 30 SONEL KT 640 THERMAL IMAGER GL E ttotubDtx GG PM EUN Detailed description on how to use infrared video recording options is available in section 11 Infrared Video Recording and also in Sonel ThermoAnalyse user manual 8 9 Help Select help option to activate short guide containing basic information on how to use the camera displayed on the screen About Update 8 10 Information on hardware and firmware version Info option displays information on the hardware and the firmware version used in the camera on the bar at the top of the screen About Update 8 11 Firmware update To update the firmware upload the latest version of it into the main folder on SD card and insert the card into the slot 15 Then choose option as below About Update Update will be performed automatically if there is a proprer version of the firmware up loaded on SD card newer version than the one currently used Gre USER MANUAL 31 9 Accurate temperature measurement The accuracy of temperature measurement depends mainly on the followi
26. This computer View your active networks Connect or disconnect Sind Access type Internet ie a HomeGroup Joined Home network Connections 42 Po czenie lokalne Unidentified network Access type No network access Public network Connections 4 Local Area Connection Change your networking settings Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or access point ku Set up a new connection or network Select connection using USB Ethernet RDNIS Gadget e gt Control Panel gt Network and Internet Network Connections gt MEN Organize 7 Disable this network device Diagnose this connection Rename this connection gt Sie Local Area Connection Potaczenie lokalne E Realtek PCIe GBE Family Controller Right click and select Properties chose Internet Protocol Version 4 and click on its Properties as below 46 SONEL KT 640 THERMAL IMAGER 7 Local Area Connection Status NE IPv4 Connectivity No network access S USB Ethemet RNDIS Gadget IPv6 Connectivity No network access Media State Enabled This tein Duration 00 06 07 7 J Client for Microsoft Networks Speed 425 9 Mbps v Kaspersky Anti Virus NDIS 6 Filter QoS Packet Scheduler 7 JB File and Printer Sharing for ft Networks D E v ink Layer Topolog scovery Mapper v L Link Layer Topology Di Respond Sen
27. V OUTPUT ccccccececcuceccucccececcecuccscuscscusescucescusesens 3 3 ON SCREEN INFORMATION ARRANGEMENT 0ccececcececcecescscuccccucescucescucscscuscscucescuss 9 3 4 VIEN Les os as ons 10 4 OPERATION INSTRUCTIONS AND THE CAMERA ADJUSTMENT 10 4 1 TURNING THE CAMERA ON OFF 10 4 2 FOCUS ADIUSTMENT socne en a Tor A AA EAA E AEE ETONE EKINEAN 11 4 3 ENLARGING IMAGE ZOOM X2 X4 68 2020200 0000000000 11 4 4 TEMPERATURE RANGE cccecocceccccaccccaccsceccsceccececsececascecascscencecensscancecatsecacsececssencess 11 4 4 1 High temperatures 11 4 5 IDA S nn nn 12 4 6 I ZBEOE QUIETIS 12 4 7 MANUAL CALIBRATION SS m Voas vo NSS 13 4 6 SELECTING THE COLOUR PALETTE cccececceccececcececcececcscscccscscscuscscusescucescusasausasens 13 4 9 LASER POINTER sis s vu mentem ipM in EC 15 ATO IMAGEMODES 15 5 CAPTURING AND SAVING IMAGES WITH VOICE ANNOTATION 16 6 MEMORY BROWSNIG sesesesesscscsesesesesesesesesesesscsoseseseseseseseseseoscscsesesesesesesesesese 18 7 5 020099 20 Fed ANA a I NL dain eds E seman 20 7 2 EIU QC IDA NETTE 21 7 3 AREA ANALYSIS 22 7 4 T OTHERM ANALISIS 23 8 FUNCTIONS AND PARAMETERS
28. angle shaped box De pending on the options selected in analysis settings see section 8 1 it can display maximum average or maximum temperature on the line i a 4 7 c Sm 7 T ol 2 K 005 B Xai 09 15 24 Real Time OQ 1X When the maximum temperature is selected in analysis settings displayed temperature value for given line is red coloured For average temperature it s black and for minimum it s blue GL USER MANUAL 21 Using touch pen line can be moved to any place on the screen Press and hold the square with temperature and slide it to a new place on screen Press the touch pen against the square on the other end of line and move its position to prolong the line rotate it etc To delete line select it by pressing square or rectangle with touch pen green arrow will appear when selecting square and press bin symbol m on tool bar Up to 8 lines which temperatures are read and displayed in rectangle boxes at their end can be added on screen 7 3 Area Analysis Press pen or use Joystick on button available under expandable AnalysisTools icon to add rectangle area with its temperature on screen Depending on the options se lected in analysis settings See section 8 1 it can display maximum average or maxi mum temperature within the area When the maximum or maximum temperature is se lected in analysis settings displayed temperature value is accompanied by its corre
29. are available Palette can also be changed in image palette window when it s not displayed press on tool bar to initiate it EL x E 9 Image Palette n x 45 6 7 8 Reference images rendered in different palettes are presented in section 4 8 Palette 9 is reversed palette 1 Video menu Auto Adjust command Use this command to adjust image color automatically or manually In Auto adjustment mode the software chooses optimal settings In Manual adjustment mode user can map the temperature range of the selected palette by defining max and min temperature Note Each and every adjustment of the range see next command will change the tem perature range and will switch the image into manual mode Run this command to return to auto mode 66 SONEL KT 640 THERMAL IMAGER Gres l Sod Sonel ThermoAnalyze KT640 WIFI 80 Video Measure Joos Window 2 lagi xim amp amp ge om v Auto Adjust 1 Gauge Setting lage Palette KT Control F180 oo Auto Focusing CTRL F 1 IS Py 71 Pause M Forward m L 12 53 455 7 3 Infor Data Gauge imag F2 Calbrate F3 Near Focus F4 Far Focus Video menu Gauge settings command Allows to manage temperature colors for every opened video file Select this function and adjustment bar will appear u
30. bserve the following guidelines e make sure the camera and its accessories dry when storing the camera for a prolonged time remove the batteries e allowed are storage temperatures specified in technical specifications e in order to avoid complete discharging of rechargeable batteries during prolonged storage charge them once in a while 76 SONEL KT 640 THERMAL IMAGER Gre 18 Equipment Standard bundle supplied by the manufacturer includes 1 KT 640 Thermal Imager 2 Detacheable VGA touch screen 3 Lithium rechargeable battery 2 pcs 4 External battery charger with AC adapt er 5 RS232 TV interface 6 VGA video cable 7 USB cable 8 110 230V AC adapter Sonel USER MANUAL 77 19 Dismantling and disposal Used up electrical or electronic equipment must be collected selectively i e must not be mixed with waste of other types Used up electronic equipment must be delivered to an appropriate collection centre in ac cordance with regulations related to used up electrical or electronic equipment Before delivering the equipment to the collection centre do not attempt to dismantle any of its parts NOTE Follow local regulations related to disposing of packaging used up batteries and rechargeable batteries 20 Manufacturer The manufacturer and provider of warranty and post warranty services for the instrument IS SONEL S A ul S Wokulskiego 1 1 58 100 Swidnica Poland
31. ch screen to switch from automatic temperature mode into manual mode This transi tion will be indicated by the M letter replacing A letter on the screen see section 3 3 and the temperature that can now be adjusted manually will be highlighted by the blue line framing the field in which it is located Now you can change the upper limit of the tem perature range by moving Joystick up down or by sliding touch pen across the tempera ture bar Whili changing the temperature its value is marked by yellow background To change the lower range press 6 button again M c Press and hold 6 button for 2 seconds or click M letter on icon with touch pen to go back into automatic temperature range selection mode 4 4 1 High temperatures filter Full temperature range of KT 640 is 20 C do 800 C It is divided into two filter ranges standard filter 1 range 20 C do 250 C and high filter 2 range 200 do 800 When the temperature of the measured object exceeds selected filter range instead of temperature values the camera will display following symbols on screen or Those symbols indicate manual filter range adjustment To change the filter range go to real time image and press button for 3 seconds Gre USER MANUAL 11 4 5 Emissivity 0 5 To change the emmissivity coefficient value press and hold icon with touch pen on the value above sign and while keeping the pen pr
32. disk for this feature click Have Disk Show compatible hardware Manufacturer Marvell M Microsoft Corporation Motorola Inc 4 m 12 a This driver is digitally signed Tell me why driver signing is important Confirm your selection in Device Manager and the camera will be installed as network adapter 44 SONEL KT 640 THERMAL IMAGER rer Device Manager File Action View Help 43 2 Rooster Computer gt Disk drives AX Display adapters 9 DVD CD ROM drives amp Human Interface Devices IDE controllers gt Keyboards gt Mice and other pointing devices Monitors amp Network adapters X USB Ethernet RNDIS Gadget Portable Devices Ports COM amp LPT Processors Sound video and game controllers I amp System devices gt Universal Serial Bus controllers Go to Open Network and Sharing Center in Sontrol Panel or through shortcut on task bar Currently connected to a Sie Internet Go to change adapter settings rer USER MANUAL 1 Center 16 41 2013 09 03 45 x Li T i gt Control Panel Network and Internet Network and Sharing Center vi s e Control Panel Home m View your basic network information and set up connections Change adapter settings See full map Change advanced sharing settings eR Multiple networks Internet
33. djust transparency FUSION mode Gre USER MANUAL 15 Fusion 09 15 24 Fusion Infrared image transparency level and distance from the object can be adjusted using ver tical and horizontal sliders using touch screen or Joystick Selecting the lowest transpar ency value will result in only visual image being displayed Pressing IR or button re sults in return to displaying full screen infrared image in real time mode It is advised to use FUSION mode for distances greater than 1 5m In case of smaller dis tances significant displacement of both images can be observed Parallax phenomenon 5 Capturing and saving images with voice annotation Caution KT 640 utilizes external memory SD card put inside the slot 15 If the SD card is not inserted the camera will display infrared images in real time mode and image can also be freezed or being analysed however it is not possible to store it in the memory The lack of SD card is indicated by the symbol displayed on status bar 09 23 53 Real Time KT 640 displays image continuously refreshing it 60 times per second To capture an im age press 5 6 button which will freeze an image and will display menu elements on screen Information about the freeze mode is displayed on the bottom bar At this point press S button to save thermal image along with its corresponding visual image A C click on temperature range icon number defining upper range
34. e battery Connect the AC adapter to the 14 socket to start charging procedure Charging can be performed only when the camera is not being used During camera operation current power supply source indicator is displayed in the lower right corner of the screen E battery power supply mains power supply 10 1 Using AC adapter Connecting AC adapter is signalled by LED indicator 22 When the camera is turned on the indicator shows battery charging status flashing red while charging and lit green when fully charged 10 2 Battery power supply After turning the camera on withot AC adapter LED indicator 22 flasher green red alter nately for few seconds During camera operation LED indicator 22 is off During camera operation the battery charge level is being shown in real time in lower right corner of the screen on status bar as below v The camera can also make audible sound when battery charge level drops down below the critical value This feature can be enabled in function settings section 8 4 max 10 2 1 Charging batteries When the camera is turned off and the battery is inside connecting the AC adapter and starting the charging procedure is signalled by the charging indicator 22 flashing red while charging and lit green when fully charged When the battery is not being charged the indication is turned off LiOn battery does not require performing full charging discharging seq
35. e is saved as VISxxxxx jpg where xxxxx is the same number as in its corresponding thermal image file name Both files must be placed in the same folder if visual image is to be used for analy sis in Sonel ThermoAnalyse program me click on icon to go to infrared video record mode described in details in section 11 6 Memory browsnig Go to Menu see section 3 4 and click on the Filelist option to proceed into browsing and editing images stored in the memory on SD card Filelist AnalysisTools Palette ReferenceEmiss 18 SONEL KT 640 THERMAL IMAGER Gre Click on the thermal image thumbnail to open it in the mode allowing to view its corre sponding visual image play voice note and perform analysis click d icon to open analysis submenu Switch to infrared video file list to open videos stored on the memory card Click on the symbols located on the bottom bar to to the list of saved static thermal images to the list of saved infrared video files CT to toggle between screens with saved files between those two symbols number of screens available is shown along with the number of currently viewed screen T delete selected thermal image 7 delete all thermal images x4 return to real time mode Return to real time mode can also be executed by pressing C 6 button Sonel USER MANUAL 19 T Thermal image analysis Thermal image analysis is pos
36. earch for driver software Search automatically for updated driver software Windows will search your computer and the Internet for the latest driver software for your device unless you ve disabled this feature in your device installation settings Browse my computer for driver software Locate and install drrver software manually Choose let me pick option as below Browse for driver software on your computer Search for driver software in this location 4 EE Include subfolders gt Let me pick from a list of device drivers on my computer This list will show installed driver software compatible with the device and all driver software in the same category as the device And then select producer Microsoft Adapter Remote NDIS compatible Device GL USER MANUAL 55 Select Network Adapter Click the Network Adapter that matches your hardware then click OK If you have sa installation disk for this feature click Hawe Disk Show compatible hardware Manufacturer Network Adapter Marvell Cal OpenCable Receiver Preproduction Test Device Microsoft v ue Remote NDIS Compatible Device gt lrscn PAIR A Eg This driver is digitally signed Have Disk Tell me why driver signing is important Ignore the wwarning and click Yes to confirm Update Driver Software USB Ethernet RNDIS Gadget Select Network Adapter K Click the Network Adapter that
37. ed independently just like for the static images 3 files with the same names and different extensiones are stored video file avi in h 264 format which can be played in any video player installed on PC second one is raw file containing thermogram data The third one is jpg file used as the video s thumbnail It al lows to perform detailed analysis during video recording process as well as the analysis of saved thermogram 12 1 Recording on SD card This function can be selected by in main Menu TouchPen VideoRecord WiFi or through expandable tool d bar or by pressing button and finally by pressing and holding S button for 2 seconds Select this function to make video recording window appear on screen 00 00 M85 x with record stop and exhit buttons Click on red button with touch pen to start recording on white square to stop recording and to save recorded footage automaticaly Video is recorded at 25 frames per second frequency Recording can also be stopped and stored in the memory by pressing S 6 button Stored IR video files can be browsed in the camera see section 6 or played on PC with installed media player 12 2 Recording on hard drive Operating the camera recording and analysis in video mode while storing data on hard drive is possible by using Sonel Thermo Analyze program supplied with the camera Driver supplied on CD along with the camers has to be installed The camera can be
38. eo Measure Tools View Window Help GE lel R 4 kas Temperature Aarm Enabled Alarm ctrl A w F Vu Auto Capture 4 Alarm Setting fs Record Analysis Data Ty mim Enabling the alarm is confirmed by Y mark The procedure of changing alarm sound is described in Sonel Thermo Analysis software manual Note This command can also be activating by pressing Ctrl A 1 12 6 Record Analysis Data Command Use this command to export real time temperature data analysis results into txt file or chart The data can be displayed as point line or surface chart according to selected time intervals Detailed description of this command and analysis example is presented in Sonel Thermo Analysis software manual 13 Data transmission Static thermal images files with their corresponding visual images and infrared videos are stored on replaceable SD card of 32GB maximum size The card must be formatted into FAT32 file system Data from SD card can be read through SD card readers External SD card reader compatible with USB2 0 interface comes along wite every KT 640 as stand ard accessory Gre USER MANUAL 71 14 Specifications Imaging Performance Detector type Uncooled FPA microbolometer 640x 480 pixels 25um Spectral Range 8 14 Thermal Sensitivity 0 05 C at 30 C Field of View Focus 25 8 x 19 5 35mm 11 5 8 6 80mm 45 7 x 35 1 19mm Focus Automatic or motorized
39. eparately The battery should be stored in dry cool and well ventilated place and it should be pro tected from exposure to direct sunlight Optimal ambient temperature for long time storage of the battery should be maintained below 30 Celcius degrees If the battery is stored for an extended period at a location with high temperature in it then the chemical processes occuring within it may shorten its expected life span Typical estimated life of Lithium lon battery is about 500 1000 charge cycles Those bat teries reach their maximum capacity after being formatted 2 3 charge recharge cycles The most important factor that influence the life of the battery is the discharge level dis charge depth The more discharged is the battery the shorter is its life span During nor mal operation camera works until reaching certain point of discharge Reaching this point is when the charging should be performed in the camera or in external charger Memory effect occurs in lon batteries in limited way Those batteries can be charged even when not reaching discharge level with no serious consequences It is important however to perform full charging cycle once in a while during regular operation of the camera LiOn batteries continue to discharge at approximately 3096 a month while in storage Keeping the batteries in high temperatures may even speed up this process twice In or der not to allow extensive discharge ot the battery after which formatt
40. esigned to work with the touch screen 3 Function buttons Joystick and on screen menu 3 1 Buttons layout Access to the camera s functions is provided through the buttons 16 located on the top side of the housing C 8 buttons 18 21 located under the power off button and through Joystick 11 Buttons layouts is presented at the inside cover page GL USER MANUAL 7 A button allowing to switch between temperature ranges displayed on screen and from auto mode to manual mode C press this button to cancell currently selected function Pressing C button several times will result in returning to the previous sub menu stepping back from different levels of parameters and subfunction menus until getting only visual image available on screen with no menus on Press and hold button for 2 seconds while having only thermal im age on screen to perform calibration of the camera S freezes thermal image on screen Press the button again to save the image into the memory Joystick can be pressed like button and it can also be moved in both up down and left right axis Joystick operation depends on the currently running function 3 2 Viewfinder touch screen TV output During the camera operation in real time mode infrared image is displayed on both screen 1 and viewfinder thermal image refresh rate is 60 times per second After selecting proper functions by using buttons or touch screen the following are being
41. essed against the touch screen move it up value will increase or down decrease value can be also changed in Target menu in target parameters settings described in section 8 2 Analysis Target System Function Default 0 5 Whilst clicking on emissivity coefficient symbol on Ed icon or after selecting this function from main menu Filelist AnalysisT ools Palette ReferenceEmiss the list of the most common materials with their emissivity coefficient values will be dis played Material Emissivity Material Emissivity Water Brass plate Stainless steel Human skin Aluminum plate PVC plastic Asphalt Polycarbonate Concrete Oxidized copper Cast iron Rust Rubber Soil Wood Aluminum black dull Brick Paper black dull Tape Gypsum Paint The right material can be selected by navigating across the list with Joystick and con firmed by pressing the Joystick button Close the list by pressing button Selection can also be made by using the touch pen 4 6 LED flashlight In order to improve the work in dark locations KT 640 has been equipped with LED flash 12 SONEL KT 640 THERMAL IMAGER Gres light Turning it on is executed by pressing 18 button Pressing the 18 button again will increase the intensity of the flashlight brightness 3 levels up to its maximum level Press ing the 18 button further will repeat the sequence turned off level 1 level 2 level 3 turned off etc Inf
42. g GL USER MANUAL 9 An additional point indicating the location of the lowest or the highest temperature can be put onto the screen Activation and selection of this point can be made in the analysis pa rameters settings section 8 1 Functions put together in 4 groups can be selected upon expanding upper drop down Menu Analysis Tools options depend on whether the camera displays stored image fro zen image or real time image 3 4 Menu In real time mode when there is no icons on the screen press the Joystick twice or touch the touch screen once and then repeat the same on the appearing icon to make the drop down menu expand It contains a list of functions their settings and parameters Menu functions are grouped into 4 sections Navigating through the Menu is executed by using the Joystick or by the touch secreen Filelist AnalysisTools Palette ReferenceEmiss Analysis Target System Function Default TouchPen VideoRecord Individual functions available on the menu are described in subsequent sections of this manual 4 Operation Instructions And The Camera Adjustment 4 1 Turning the camera on off Press and hold the 7 button for around 2 seconds to turn the camera on Splash screen will apear on the display and then the camera will perform self check test after which the camera is ready to use and goes into displaying real time infrared image In order to turn the camera off press and hold the Power
43. gram for the first time with the camera connected in online mode Windows Firewall alert may appear on screen If this case click allow to connect to private networks Sonel hermoAnayze KT640104 Video Pomiar Narz dzia Widok Okno Pomoc 10 amp nl O Hees Paleta obrazu KAREE EAN P AREI Alert zabezpiecze systemu Windows 1 Zapora systemu Windows zablokowata niekt re funkcje tego programu Zapora systemu Windows zablokowa a niekt re funkcje programu ThermoAnalyze Application we wszystkich sieciach publicznych i Wydawca Sonel S A cie ka C program files x86 sonel thermoanalyze sonel thermoanalyze exe Zezw l programowi ThermoAnalyze Application na po czenia w tych sieciach Sied prywatne takie jak sieci domowe lub firmowe Przyrz d takie w portach lotniczych i kawiarniach niezalecani takie sieci maja slabe abesse sene b tic siot KH ice wiaze sie z zezwoleniem ramowi na dos zez Zezwalaj na dostep Anuluj Sonel USER MANUAL 61 12 Recording infrared videos IR video can be recorded and stored on both SD card and also directly on PC hard drive using Sonel Thermo Analyze program supplied with the camera Whether recording on SD card or directly on PC s hard drive all information is being stored each frame is thermogram meaning that the temperatures of each point are stor
44. hite nn 0 87 D 0 90 lacquer polished black 0 87 charcoal 0 96 lacquer dull 0 97 que 0 13 lacquer 0 31 tungsten 22 0 11 MEER 0 97 Old 0 02 MAGN CSI EN 0 12 WOM GIOSSV P 0 16 copper 1 12 0 65 iron heat 0 77 copper oxidized black 0 88 OXIOIZ d ss Seis decease orit re rire 0 74 copper 0 07 iron DOIISIHO iei costo 0 23 copper polished annealed 0 01 0 02 iron and steel oxidized 0 85 la ir c 0 10 cast raw 0 81 brass 2 0 61 cast DOIISDBU 0 21 nickel 0 05 Gre USER MANUAL 75 16 Cleaning and maintenance NOTE Use the below specified methods of maintenance only Camera enclosure all surfaces except for optical elements of the camera be cleaned with a soft and moist cloth with generally available mild detergents Do not use any solvents or cleaning agents that could scratch the
45. i AutoPlay B Credential Manager li Desktop Gadgets Display Folder Options HomeGroup Keyboard Network and Sharin Performance Inform W Power Options or through Hardware and Sound section BA gt Control Panel Adjust your computer s settings System and Security Review your computer s status Back up your computer Find and fix problems Network and Internet View network status and tasks Choose homegroup and sharing options Hardware and Sound View devices and printers Add a device Programs 25 we Uninstall a program t Control Panel Hardware and Sound View by Category User Accounts and Family Safety Y Add or remove user accounts Set up parental controls for any user Appearance and Personalization Change the theme Change desktop background Adjust screen resolution Clock Language and Region Change keyboards or other input methods Change display language Ease of Access Let Windows suggest settings Optimize visual display Control Panel Home Devices and Printers Securit Add a device Add printer Network and Internet AutoPlay Hardware and Sound Sound Adjust system volume Programs User Accounts and Family Safety Power Options Change power saving settings eon Appearance and Personalization Clock Language and Region Choose a power plan Pa Change system sou
46. in part 2 and 3 of main Menu Analysis Target System Function Default TouchPen VideoRecord WiFi 8 1 Thermal images analysis parameters After selecting main Menu go to section 2 and select with touch pen or Joystick Analy sis tab ner USER MANUAL 23 Analysis Target System Function Default Below window will open Analysis Setting LineColor Black v Hot Cold Spot Disable AnalysisFunction Max TempAlarm High AlarmValue mme Ok Cancel Using Analysis Setting window following parameters can be adjusted Isotherm Color this is the color that is being applied to the areas from selected temper ature range during isotherm analysis Hot Cold Spot you can decide here whether or not an additional spot showing coldest and hottest point along with its temperature value should be visible on screen as an ad dition to central point Enabling this function will result in showing the lowest or the highest temperature on screen depending on the selected temperature alarm see TempAlarm AnalysisFunction Select the temperature that will be displayed during line or area analysis average maximum or minimum TempAlarm Audible alarm that will activate after exceeding selected temperature level Selecting Low will trigger the alarm when the temperature drops below selected AlarmValue Selecting High will trigger the alarm when the temperature exceeds se lected AlarmValue AlarmValue
47. ing in the clockwise direction Fift one will appear in the center of the screen User should always be pressing the center of each marker with touch pen Gre USER MANUAL 27 09 15 24 Real Time Then confirm the end of calibration procedure NOTE If the calibration procedure was not conducted properly and its results were acci dentally saved and the touch screen does not respond to the stylus touch use Joystick to repeat the calibration procedure 8 7 Video recording infrared video recording procedure has been described in details in section 1 1 1 TouchPen VideoRecord WiFi 8 8 WiFi This function allows to set the camera to work wirelessly Network to which the camera will be connected can not be password protected NOTE PC camera communication is possible after installing proper drivers sec tion 12 To get wireless connection select WiFi option from the Menu TouchPen VideoRecord WiFi WiFi Setting window will open Use stylus and turn the wireless network on as on the im age below 28 SONEL KT 640 THERMAL IMAGER Sonel WiFi Setting 09 15 24 Real Time 09 15 24 Real Time Select the line containing desired network with a stylus and additional window with IP address will appear WiFi Setting 192 168 0 109 09 15 24 Real Time O_1X The IP address should be used in Sonel ThermoAnalyse software Go to File gt Video gt Device Video ner USER MANUAL 29 Sonel
48. ing is necessary charge the battery once in a while including the ones that are not being used Modern fast chargers detect both too low and too high battery temperatures and react appropriate Too low temperature should prevent from starting the charging procedure which could irreversably destroy the battery increase of the battery temperature suggest that charging procedure is over and this is normal and expected phenomenon However GL USER MANUAL 35 charginf the battery in high ambient temperature apart from decreasing battery life re sults in the increase of the battery temperature In this case the battery will not be fully charged to reach its full capacity Do not charge and use LoOn batteries in extreme temperatures Extreme temperatures decrease battery life Avoid placing devices running on batteries in very warm places Nominal working temperature must be strictly abide 36 SONEL KT 640 THERMAL IMAGER Gre 11 Camera s Driver and Sonel ThermoAnalyse PC Installation Guide The driver and the PC program can be installed on Microsoft amp Windows XP and higher operating system x86 x64 KT 640 driver installs as an additional network interface card 11 1 Windows XP installation guide To install the camera on Windows XP use the driver supplied with the camera on CD or download it from www en sonel pl Turn on the camera and wait antil self test procedure is completed and then connect the camera to USB port on com
49. ject defining the area for which the temperature analysis will be performed Lutownical iry 318 lol x KIKE EAE E SI Click on the object to open up a window where you can change the line color and trans parency of selected object 68 SONEL KT 640 THERMAL IMAGER Sonel Circle Property Name coo a Transparence V Show max position Show min position Show temperature Custom show avarge Temperature Show max temperature Snow min temperature Lox Double click on Track View window to open TrackView Settings window where you can change its settings background color color of diagram axes min and max temperature on axes Click OK button to save changes or Cancel Button to close the window without saving changes TrackView Settings 4 e Background Colour ne DM Min Temperature 0 1 GC Max Temperature i C NOTE Chart line shares the same color with the object it represents Thanks to the fact that the chart line color depends on the object color you can analyze the change of tem perature of many spots and areas in one window Press F11 to save the current TrackView window as JPG file in the directory where the captured pictures of the infrared video are stored see section 11 2 3 Measure menu Histogram command Select Histogram or Other histogram to draw percentage allocation of temperature in real time for the whole infrared video or its
50. k on icon to open dialog box that allows to record voice note up to 1 minute lenght which will be saved along with thermal image 1 00 Sonel USER MANUAL 17 press g to start recording backward counting starts showing remaining time press to stop recording and press n to play recorded note The record can be repeated and doing this will erase the previous one press to mark image On the file list see section 6 memory browsing the image will be marked with the flag icon placed in the upper left corner if press to save thermal image along with the optional voice note and mark The same result can be achieved by pressing S button Remarks 1 Thermal image is saved in extended jpeg format Thanks to that it can be viewed in all image browsers and graphics softwares stored preview image will be viewed in those cases In addition to that all information related to the thermogram is stored in one single extended jpeg file as well temperature of each and every pixel of thermal image voice note and mark flag symbol described above 2 editing thermal image in software other than Sonel ThermoAnalyse will result in loosing all thermographic data 3 If there is not enough space to save a file on SD card or when a saving error oc curs proper information will be displayed on screen 4 Saved thermal image file name is IRIxxxxx jpg where xxxxx are digits Addition ally separate file with visual imag
51. m it at human and animals NOTE Use only standard and additional accessories listed in Equipment section Using other accessories does not ensure proper operation of the camera and may cause its damage SONEL KT 640 THERMAL IMAGER Gres NOTE Due to the continuous development of the device the design of the display and its certain features may be slightly different than presented in this manual 2 Preparing the camera to work KT 640 can work with touch screen detached however having it mounted significantly simplifies its operation and features selection When touch screen is detached main menu functions and analysis tools can be activated by pressing and moving Joystick Thermal image can be viewed through view finder 9 It is possible to activate laser point er flashlight real time image preview buttons 18 20 using auto focus button 21 man ual focus adjustment and zooming the image with Joystick 11 In order to have both thermal and real time image projected on large screen 1 and to have easy access to advanced functions attach it by the grip to the socket on the upper side of the camera The grip should be slided into the socket from the front side till the end in the manner that allows the proper connection of the LCD contact pins 25 and then se cure the grip using tightening gear 24 by turning it right Touch pen slot 23 is located on the bottom part of the screen frame 1 Touch pen is d
52. matches your hardware then click OK If you have an m installation disk for this feature click Have Disk C Show compatible hardware Manufacturer Marvell i Installing this device driver is not recommended because Windows Microsoft cannot verify that it is compatible with your hardware If the driver is not compatible your hardware will not work correctly and your M computer might become unstable or stop working completely Do you want to continue installing this driver Proper installation will be confirmed as below 56 SONEL KT 640 THERMAL IMAGER Windows has successfully updated your driver software Windows has finished installing the driver software for this device Remote NDIS Compatible Device In device manager another network adapter will appear USB Ethernet RNDIS Gadget File Action View Help sis Sl WS E RooPC b y Audio inputs and outputs p jE Computer gt gg Disk drives gt Display adapters gt DVD CD ROM drives p Human Interface Devices b IDE ATA ATAPI controllers p Keyboards b hn Mice and other pointing devices Monitors EP Network adapters Microsoft Kernel Debug Network Adapter m arl patroler b El Portable L vic s Ports COM amp LPT du Print queues After finishing installation go to Desktop Sonel USER MANUAL 57 Mi Teme Pyer wins Raiders b over Matt Flynn
53. nder the thermogram as below lt alows to adjust the range of reproduced temperatures 2 O Optimal settings be restored at any time by pressing Cancel button or Auto see above Note Adjustment bar appears and disappears also upon double mouse click at any place within the thermal video window Measure menu Temp Unit command Allows to choose Celsius or Fahrenheit degrees as temperature units 4 Sonel ThermoAnalyze KT640 WIFI 80 Tool View Window Help Celsius Fahrenheit Measure Temp Unit Show MaxTemp Pos Show MinTemp Pos Show Track View Measure menu Show Max Temp Pos and Show Min Temp Pos commands After selecting any of those two commands two markers will show up over the thermo Gre USER MANUAL 67 gram area x symbol will indicate the point of the highest temperature while symbol will indicate the point of the lowest temperature Additionally values of those temperatures will be displayed alongside the markers 44 b mim eS Measure menu Show track view command Use this command to display diagram being drawn in real time representing tempera ture fluctuation of spot lines or areas added to the infrared video For spot it will display its current temperature For lines or areas it will display the aver age min or max temperature of the selected lines or areas Choose this command after adding ob
54. nds Require a password when the computer wakes Mouse Change default settings for media devices Play CDs or other media automatically Manage audio devices Change what the power buttons do Change when the computer sleeps Open Device Manager and find RDNIS Ethernet Gadget in Other Devices tab Right click on it and select Properties and then Update Driver Sonel USER MANUAL 43 File Action View Help e nldiBalt 4 4 Rooster gt Computer gt x Disk drives gt MY Display adapters gt 52 DVD CD ROM drives gt Human Interface Devices gt g IDE ATA ATAPI controllers gt Keyboards gt P Mice and other pointing devices gt Monitors gt amp Network adapters 4 Other devices RNDIS Ethernet Gadget gt Portable Devices Scan for hardware changes gt age Ports COM amp LPT Properties gt Processors gt Sound video and game controllers gt ti System devices Opens property sheet for the current sele ee eee B OE Update Driver Software USB Fthernet RNDIS Gadget cd 22 ae How do you want to search for driver software 2 Search automatically for updated driver software Windows will search your computer and the Intemet for the latest driver software for your device unless you ve disabled this feature in your device installation settings
55. ng factors Dur ing measurement the camera makes corrections based on signals from its sensors However in certain situations manual correction of parameters might be necessary Emissivity Infrared radiation measurements are based on reception of infrared radiation emitted by objects The amount of radiated energy depends on two base factors the tem perature and the emissivity of the surface of an object Default value of the emissivity coeffi cient is 0 98 and it is applicable to most surfaces Values of the emissivity coefficient for some materials are presented in the emissivity table see chapter 14 Improper value of the emissivity coefficient can cause significant errors of the temperature readout therefore the camera allows for adjustment of the emissivity coefficient value within the range of 0 01 1 00 see section 4 5 and 8 2 When changing the emissivity coefficient value it is crucial to check the readout of ambient temperature in the camera see below Accuracy of measurement also depends on ambient temperature By default the tempera ture measured by the camera is used however it might be improper especially during op eration in low temperature or measurements from a location of temperature differing from ambient temperature of the examined object In order to maintain accuracy of measure ments proper value of ambient temperature should be accounted for especially if the emissivity coefficient is changed or these
56. ng the CD containing the software supplied with your camera into CD ROM drive installation dialog box will appear If the installation box doesn t appear automatically double click autorun exe file in the CD s main folder After selecting language new dialog box will appear Choose thermal cameras and then install ThermoAnalyze Analyse ond report results with the attached software ThermoAnabyze Correct the emissivity foe the whole or part of the thermograph emissivity can be corrected separately for each selected image area Selection of reviewed areas select rectangular or oval area or of amy shape Then select the joint part of selected ir cot the as end move their borders Read the temperature at amy point when the cursor is placed in the window R displays continuously read temperatura with coordinates Other saved infarmation maximum temperature humidity emissivity is alse available of images particularly when visual comparison af t thermogragh with the details on the visual image i Installation process will begin follow the on screen instructions NOTE 1 Without changing the default installation directory the installation procedure will allow the program to be installed in C Program files Sonel ThermoAnalyze The installa tion procedure will add a shortcut icon Launch Sonel ThermoAnalyze to the Desktop and to the Start menu NOTE 2 When starting the pro
57. onze dull 1 see i xxt 0 22 plastic DIaCk iss ee eene 0 95 bronze 0 10 paties au od A 0 10 bronze rough cie nene 0 55 porcelain 0 92 brick glass 0 2 2 0 85 1 101 S 0 10 brick fireproof 0 94 lat DOIACK 0 96 Cement so ss 0 54 SIME a n 0 03 cement concrete 0 90 steel 2 2 22 2 0 28 ENOO oue a as Ei 0 15 steel oxidized seska 0 88 chrome 0 10 steel rolled 0 24 Viss os se a T 0 09 steel 0160 ERE 0 56 ZINO CM rEEET 0 05 ci iM JI MOPE 0 96 lese dio m a 0 93 steel rusty red rnt 0 69 ose m 0 94 steel 0 11 olay N60 ies so 0 91 ro 0 90 UL 0 40 ecc M anaes 0 92 TNI 0 85 gass OUI PP 0 96 ground 2 00 0 24 2 0 93 SHOW a 0 80 sa ee ee eee earn 0 93 tape insulation 0 95 S19 0 lv S 0 18 IBC ne E eee EA 0 85 T ce ee ee ee ee 0 93 MM us 0 30 lacquer w
58. ormation about the flashlight status and its current brightness level is displayed as an icon in the low right corner of the screen Enabling the flashlight and changing its bright ness can also be executed by clicking its icon on touch screen with pen This function is available when activated in the system settings menu see section 8 3 4 7 Manual calibration During operation the camera runs periodic auto calibration procedure it is signalled by the closing shutter sound and the Calibration word appearing on the bottom of the screen Calibration can also be triggered manually at any time while being in real time mode with infrared thermal image being displayed press and hold button for 2 sec onds 4 8 Selecting the colour palette Color palette corresponding to the temperature values can be changed in every mode Select palette option in the Menu Filelist AnalysisT ools Palette ReferenceEmiss or click on the temperature bar on screen and a window with the selection of 8 palettes will pop up on Palette selection is made by clicking on chosen palette bar After selecting desired palette click once again on the temperature bar or press button 6 Palette no 2 is set by de fault Gre USER MANUAL 13 14 Available colour palettes SONEL KT 640 THERMAL IMAGER 4 9 Laser pointer Laser pointer can be activated while being in real time mode by pressing 20 button
59. ouch pen or Joystick Func tion tab Analysis Target System Function Default In the dialog box below following settings can be done Function Setting Lens Laser FlashLight AutoPowerOff PowerAlarm Cancel 26 SONEL KT 640 THERMAL IMAGER Sonel Lens lens selection only when the camera is calibrated to work with more than one lens Laser Enabling Disabling the possibility of using laser pointer FlashLight Enabling Disabling the possibility of using LED flashlight AutoPowerOff disable or enable to power off after 10 30 or 60 minuts of no activity PowerAlarm disable or enable audible alarm when battery level is critically low 10 times every minute 8 5 Restoring to default settings After selecting main Menu go to section 2 and select with touch pen or Joystick De fault tab Analysis Target System Function Default And then confirm the action in the window below Factory Date Reset us Default settings laser pointer LED flashlight Auto Power Off Power alarm and tem perature alarm disabled Frame Aver 1 disabled frames averaging 8 6 Touch Pen calibration After selecting main Menu go to section 2 and select with touch pen or Joystick Touch Pen tab TouchPen VideoRecord WiFi After selecting this option four markers points will start appearing in the corners of the screen by one starting from the top left corner proceed
60. puter Computer will detect new hardware Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software Far ANDIS Ethernet Gadget If your hardware came with an installation CD floppy disk insert it now What do you want the wizard to do Click Next to continue lt Back Cancel Choose install from a list or specific location and then select to search the driver is se lected location Gre USER MANUAL 37 Found New Hardware Wizard Please choose your search and installation options gt 2 Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Include this location in the search GKT640 Driveri32bit v O Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware Driver installation will begin Found New Hardware Wizard E Please wait while the wizard installs the software Hi Acme USB Remote MDIS Network Device gt gt usballz3x sys Ta C WINDOW S Sseistem32 DRIVERS Back Hests Information suggesting that the driver is not compatible with our operating system Ignore itand press Continue an
61. rity SoundMAX Sounds and Language Cameras Tasks Center Audio Devices In the window that opens select the connection that uses installed Acme USB Remote NDIS Network device amp Network Connections File Edit View Favorites Tools Advanced Help Om O D Piem Prodes gt X Vl Address Network Connections LAN or High Speed Internet Local Area Connection 7 Local Area Connection Network cable unplugged Fire PS Connected Firewalled Bluetooth PAN Network Adapter T Intel R PROMOO0 MT Mobile Local Area Connection 8 Acquiring network address Fir Acme USE Remote MOIS Go to Properties and select Internet Protocol TCP IP and then select its properties 40 SONEL KT 640 THERMAL IMAGER Sonel 1 Local Area Connection 8 Status 2 xi General Support Connection Status Limited or no connectivity Duration 00 01 40 Speed 425 9 Mbps More information Activity Sent Received c Packets 2 0 Disable Close 1 1 Area Connection 6 Properties General Advanced Connect using Acme USB Remote NDIS Network D m b Description This connection uses the following items QoS Packet Scheduler AEGIS Protocol IEEE 802 1x v3 4 10 0 Internet Protocol TCP IP Uninstall Transmission Control Protocol Intermet Protocol
62. rive Power System Battery Type Rechargeable Li ion battery field replaceable Video files format Charging System In camera or in battery charger Battery Operating Ti Over 2 hours continuous operation me External Power Opera AC 110 230 VAC 50 60Hz 9V DC tion Environmental Specification Operating Temperatu 45 C 459 C re Storage Temperature 20 C 60 C Humidity Operating and storing 10 to 95 non condensing Image transfer thermal and visual measurement and voice to computer live video transfer to PC Physical Characteristics 0 85kg excluding battery amp LCD 1 1kg including battery amp LCD Gre USER MANUAL 73 USB 2 0 Size 186mmx106mmx 83mm Standard Model Tripod interface 1 4 20 74 SONEL KT 640 THERMAL IMAGER Gre 15 Examplary Emissivity Coefficient Values INNO PAIET IRE NOISE 0 05 lead polished l sss 0 08 aluminum Rough s 0 07 lo 0 28 Aluminum 0 25 lead oXidiZed eee metr 0 63 Pilda dievs soon 0 90 paper 20 0 0 222 0 90 asbestos board 0 96 paper black 1055 0 90 asbestos fiber 0 78 paper black 0 94 akelite er aeee 0 93 paper 0 92 br
63. se 37 11 1 WINDOWS XP INSTALLATION GUIDE aaa 37 11 2 WINDOWS 7 INSTALLATION GUIDE 42 11 3 WINDOWS 6 INSTALLATION GUIDE 48 11 4 SONEL THERMOANALYZE INSTALLATION GUIDE aaa 61 12 RECORDING INFRARED 5 62 12 1 RECORDING ON SD CARD aaa aaa 62 12 2 RECORDING ON HARD DRIVE aaa aaa 62 12 3 SONEL 2 5 8 8888 63 12 4 RECORDING INFRARED VIDEO IN REAL TIME aaa 64 7220 VIDEO MODE MENU N D 66 12 6 RECORD ANALYSIS DATA COMMAND V ccccccecceccecceccsceccecceccscescccuccecescescuscucescaseuses 71 17 DATA TRANSMISSION eu 71 14 SPECIFICATIONS ccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccees 72 15 EXAMPLARY EMISSIVITY COEFFICIENT VALUES 000 75 16 CLEANING AND MAINTENANCE 76 217 CALIBRATION 76 18 EQUIPNIEN T in 77 19 DISMANTLING AND 78 20 MANUFACTURER 22252022255
64. selected part Gres USER MANUAL 69 K ox Histogram parowozPT47 irv 100 44m p gt n M RE 229 69 16 2 6 0 43 0 92 0141 0200 0 Histogram C1 NU RU AN OO 97 99 16 2 4 9 26 1 47 2 68 3 89 4 Note detailed description of commands allowing initiating and performing analysis and description on how to analyze thermograms is available in Sonel ThermoAnalyze user manual Note Isotherm command is not available in Video mode Tools Menu Temperature Alarm Audible alarm sounds whenever temperature set point is exceeded Alarm Setting set the limit temperatures crossing which activates an alarm Set Max value to activate an alarm when the temperature is higher than selected value Set Min value to activate an alarm for temperatures below the selected value Alarm Temperature Value Max 200 Mn E Save pictures Interval Image can be saved at the time when the alarm is activated It will be saved in the directo 70 SONEL KT 640 THERMAL IMAGER Ener ry where the captured pictures of the infrared video are stored section 11 2 3 Image storing will continue as long as the temperature is exceeded according to the set interval value This function can be activated by clicking Enabled Alarm Ctrl A in the tools menu Sonel ThermoAnalyze KT640 WIFI 80 GS S File Vid
65. sible for every image mode real time freezed and images stored in memory Activate expanding AnalysisTools bar from main Menu Filelist AnalysisTools Palette ReferenceEmiss Ay or by pressing EZ icon After expanding AnalysisTools bar following icons selection al low to perform spot analysis see below o line analysis see below area analysis see below isotherm analysis See below TT deleting of active area object of analysis Remaining icons available on the bar depending on the image mode we re in execute the functions described in previous sections Ay Press the triangle on the bottom of the bar to turn the bar back into icon 7 1 Spot Analysis Press pen or use Joystick on button available under expandable Analysis Tools icon to add spot on screen The spot can be moved at any place on the screen with touch pen Up to 8 spots can be added on screen Each point is accompanied by its tempera ture indication located in small field next to it 20 SONEL KT 640 THERMAL IMAGER Gre Vs 6 0 95 ig 09 15 24 Real Time O 1X To delete spot press it with touch pen select it and click m symbol on tool bar 7 2 Line Analysis Press pen or use Joystick on button available under expandable AnalysisTools icon to add line on screen Added line is displayed on screen with one end marked by yellow square and the other end with temperature indication in rect
66. t Received Description 0 Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across d verse interconnected Type in IP address as below You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain IP address automatically Q Use the following IP address IP address 192 168 2 110 Subnet mask 235 x Default gateway 192 168 2 2 Obtain DNS server address automatically 9 Use the following DNS server addresses Preferred DNS server Alternate DNS server Validate settings upon exit Press ok and data from the camera can be transferred to computer ner USER MANUAL 47 11 3 Windows 8 installation guide Before installing on Windowds 8 it is required to switch it into mode allowing instal lation of anouthorised drivers 1 Move mouse cursor to lower right corner of screen and select Settings 4 Click on change PC settings ii 59 Unavailable Motifications Power Keyboard Change PC settings 48 SONEL KT 640 THERMAL IMAGER Gre in the next window select General and then Restart now PC settings Activate Windows Personalize Users Notifications Search Share Privacy Devices Ease of Access
67. the calibration for about 2 seconde the device does not respond to user s activity it is indicated by calibration word on screen Apart from that autocalibration of 2 seconds duration performs automaticly during operation of the device and is dependent on external conditions and i salso indicated by calibration word displayed on screen Calibration can be performed manually at any time In order to do that you need to go to real time mode screen by pressing C button 6 as many times until there is only infrared image being displayed on screen with central point selected Then you need to press and hold C button for 2 seconds calibration procedure will be per formed and it will be indicated by calibration note on screen During imager operation its housing temperature increases and its a normal phenomenon NOTE KT 160 Thermal camera has no parts that could be repaired by its user Never attempt to dismantle or modify the camera Opening the unit invalidates the warranty NOTE Laser pointer installed in the camera may be dangerous to eyes in case of direct contact DO NOT DIRECTED THE LASER BEAM TOWARDS OTHER PERSONS OR ANIMALS Please note that the laser beam may reflect off shiny surfaces After turning the camera on it performs internal test during which for few seconds laser pointer is being turned on as well After turning the camera on until it reaches the point of being fully operational it is forbidden to ai
68. type Save backup copies of your files with File History lu Set up Family Safety for any user Find and fix problems usa _ Appearance and Personalization Network and Internet ay Change the theme tk View network status and tasks i Change desktop background Choose homegroup and sharing options Adjust screen resolution Hardware and Sound D Clock Language and Region View devices and printers Add a language Change input methods Change date time or number formats Add a device Programs Ease of Access Uninstall a program Let Windows suggest settings Optimize visual display 52 SONEL KT 640 THERMAL IMAGER gt cU See below gt T a gt Control Panel Hardware and Sound Search Control Panel P Control Panel Home Devices and Printers LE at Addadevice Advanced printer setup Change Windows To Go startup options System and Security Network and Internet Hardware and Sound ad AutoPlay Change default settings for media or devices Play CDs or other media automatically Programs User Accounts and Family Sou nd Safety Adjust system volume Change system sounds Manage audio devices Appearance and ib Power Options Personalization Change power saving settings Change what the power buttons do Clock Language and Region Require a password when the computer wakes Change when the computer sleeps Choose a power plan Ease of Access Display
69. uences during ex ploitation however it is advised to perform 3 full charging discharging procedures when using for the first time The camera comes along with 2 batteries which are advised to be used alternately When using the second battery the first one should be charged Gres USER MANUAL 33 NOTE Use only the battery AC adapter and external battery charger supplied along with the camera NOTE Do not remove the battery from the camera while it s being charged NOTE Battery charging should be performed in 0 40 C temperature range 10 3 Charging battery in external battery charger NOTE Switch the camera off before removing the battery To remove the battery from the camera pull the battery comprtment cover s 8 prong 26 and open the battery compartment cover Push the battery lock lever 27 above the battery and the battery will partially slide out of the compartment allowing to remove it After inserting the battery into charger and after connecting power supply the charger will make audible sound and will display Hr Min on screen to inform about the battery charge status After finishing the charging procedure charger will also make audible sound and will display FULL on screen to inform about the battery being completely charged 34 SONEL KT 640 THERMAL IMAGER Gre 10 4 General rules of using Lithium batteries If the device is unused for an extended period remove the battery and store it s
70. urces such as the sun lasers or welding arcs etc Do not expose the camera to dust and moisture When operating the device near water ensure that it is adequately guarded against splashes When the camera is not in use or is to be transported ensure that the unit and its accessories are stored in the protective carry case Do not jam the loudspeaker holes on the camera body Do not re switch on the imager before 30 seconds after switching it off and do not remove the battery while operating the instrument Do not throw knock or shake intensely the camera and its components in order to avoid the damage Do not attempt to open the imager body as this action will void the warranty Keep the SD memory card for the exclusive use of the camera During operation if the camera is to be moved from hot cold place to cold hot place e g from inside outside to outside inside of a room switch the imager off and leave it in the new workplace for 20 minutes then turn it on and start normal operation with an accurate temperature measurement Sudden and rapid changes in ambient temperature may cause fault temperature measurement and even damage camera s IR detector Gres USER MANUAL 5 FPA setting FPA Focal Plane Array in order to ensure accurate temperature measurement the FPA detector was calibrated in different temperature points After switching the imager on it performs auto calibration procedure 3 times during the first minute During
71. with real time video footage will appear Play Pause Analysis object Full screen Record Calibration bY parowozt T47 irv 100 K X nj x start recording pause video operate shutter and make adjustments in real time mode Shortcuts you will find in video mode window F Starts online preview in Device Video mode Click to play recorded video Stops online preview in Device Video mode Click to pause recorded video bP Forwarding the video frame by frame in playback mode 44 Backwarding the video frame by frame playback mode 9 Continuous vide recording and saving it in previously selected directory File names are assigned automatically Stop recording and press the button again to start recording another file Gre USER MANUAL 65 Note button is used to both start and stop infrared video recording procedure NOTE Move the cursor to any point at the screen to display its temperature 12 5 IR video mode menu In IR video mode menu bar options are different upper part of Sonel ThermoAnalyze window Available functions are specific to infrared video mode Commands described below strictly related to real time mode operation All commands including those related to replaying and analysing recorded footage are described in details in Sonel Thermo An alyse user manual Video menu Palette command Allows to choose which palette will be used to render real time infrared images Nine pal ettes
72. yway 38 SONEL KT 640 THERMAL IMAGER Gre Hardware Installation A The software you are installing For this hardware Acme USE Remote NDIS Network Device has not passed Windows Logo testing to verify its compatibility with Windows F Tell me why this testing iz important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Acme USB Remote NDIS Network Device Chick Finish to close the wizard Go to Start menu or select Network Connections in Control Palen and select Network Connections Gre USER MANUAL 39 E Control Panel File Edit View Favorites Tools Help address gt OO dd Bb we o gt Accessibility Add Hardware Add or Administrative Automatic Date and Time C Options Tools Updates Programs P Fe Documents I 3 gt Game Internet Java Keyboard Mouse Network Controllers Options Connections A e Network Connections lt 4 Printers and Faxes Taskbar and Start Menu y Regional and Scanners and Scheduled Secu

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents