OPERATING AND INSTALLATION MANUAL
Contents
1. A key lt 4 gt or lt 6 gt lt ENT gt ENTER NEW P W 2digit lt ENT gt lt ENT gt You can select whether the DURESS mode is used for DURESS MODE SET READERI Default setting is NOT USE If you want to SOU IEE setup Duress mode press the lt ENT gt key and select gt USE by pressing the lt 4 gt or lt 6 gt key Press the lt ENT gt DURESS MODE SET key The LCD will display default Duress Password 00 gt USE Press lt ENT gt key again to enter a 2 digits Duress Password Press lt ENT gt key to finish the setting Note DURESS P W In case of Duress enter the 2 digits Duress Password 00 and press lt ENT gt key Afterwards present the card Door will be opened as normal but the Duress alarm will be generated and reported to the host PC 12 1 14 FUNCTION KEY SETTING SR505 FUNCTION FUNCTION KEY The User can decide what will be shown on display NOT USE matched with Function key Default value for FUNCTION KEY is NOT USE and set USE in order to apply FUNCTION KEY F1 F2 F3 F4 for Time amp Attendance If WAIT TIME is set system will be back to default status display OK Press ENT key to change the value from left figures FUNCTION KEY gt NOT USE 30 IDTECK FUNCTION KEY gt USE WAIT TIME 00 Star 505R pass P505R IDTECX SR505 Select mode by pressing lt 4 gt lt 6 gt key After2. TTL Output 2 test Activated two times Enter any key Buzzer Output test Activated two times l Output test end OUTPUT TEST This test is applicable to Relay1 and LED This test is applicable to Relay2 and LED This test is applicable to TTL1 OV 5V This test is applicable to TTL2 OV 5V This test is applicable to Buzzer To test the outputs press lt ENT gt key i The output test will proceed on and off twice for each output The first two tests are for the output relays Relay 1 Relay 2 You can hear the mechanical sound of relays and following two tests are for TTL output OUTPUT 5 Press any key testing The last test is setup y enu for the built in buzzer and you can IDTECK 12 4 4 LCD TEST LCD TEST Last Update Press any key 12 4 5 KEYPAD TEST KEYPAD TEST 0123456789ABCDEF 12 4 6 READER TEST READER TEST Scanning Reader 1 003123 Reader Card 12 4 7 INPUT TEST INPUT TEST INPUT TEST 1111 INPUT Star 505R gt ass P505R IDTECX SR505 Press lt ENT gt key to continue the test LCD will display all characters on the screen When the test is done the LCD will show Last Update Press any key Press any key to return to Setup menu i Press lt ENT gt key to start the keypad test LCD will display 0123456789ABCDEF on the bottom l
3. 12 3 5 ID COUNT ID COUNT lt ENT gt EVENT MEMORY EMPTY A NO y Star 505R pass P505R IDTECx SR505 ENTER NO 4 5 digit DISPLAY EVENT MEMORY NOT EMPTY DISPLAY INVALID COUNT DISPLAY ID TOTAL COUNT ID COUNT ENTER ID COUNT Invalid Count EVENT MEMORY NOT EMPTY ID TOTAL COUNT Wrong WRONG ID COUNT VALID O YES REGISTERED ID COUN lt ENTER NO YES COMPLETE i Press lt ENT gt key to change maximum ID Count Note This must be setup first before any other setup Please refer to section 7 4 ID COUNT SETTING Enter number from 500 to 10000 in multiple of 500 for the maximum User ID count Example 500 1000 2000 10000 Then press lt ENT gt key LCD will display Invalid Count error message when you enter the ID Count which is not multiple of 500 or the ID Count is not in between 500 and 10 000 LCD will display EVENT MEMORY NOT EMPTY error message when you want to change ID Count and there are some events still existing in the Event Buffer LCD will display ID TOTAL COUNT Wrong error message when you enter the less ID Count number than the number of User ID registered in the memory Note This must be set up first before other setups 40 Star 505R iPass P505R DISPLAY CURRENT F W VERSION VERSION
4. meet the market requirement for a robust integrated solution for access control and time amp attendance It is designed for low cost as well as high security convenience and reliability This user friendly device allows you to register 500 10 000 ID numbers and can keep 2 500 7 250 events Number of ID amp Events can be exchanged under the ratio of 2 to1 which means every 500 users can be converted to 250 events The Event buffer reports and archive information to Excel or Access databases and ultimately manage all access control and time amp attendance issues With a built in 4 inch RF reader and keypad for Personal Identification Numbers PIN the STAR505R offers up to two levels of ID verification You can verify by Proximity Card PIN or both and multiple verification levels can be custom programmed for each user or user group Four independent input ports can be utilized for a wide variety of controls including exit buttons door contacts PIR sensors and fire detection equipment Actions to be taken and time settings can be programmed with the front keypad or via the intuitive Windows based software program The Star 505R can be used both as a stand alone system and also be networked All control setting values such as ID numbers inputs outputs real time clock time schedules and event transaction reports can be uploaded and or downloaded to and from the host computer The compact and contemporary unit is easily installed and programmi
5. W 06 R1 ID OK 07 R1 ID ERROR 08 RI T S ERROR 09 RI APB ERROR 10 R2 ID OK 11 R2 ID ERROR 12 R2 T S ERROR 13 R2 APB ERROR 14 DURESS MODE 15 OUTPUT T S 16 IN OUT TAS lt 02 DOOR CONTACT lt HOLIDAY DEFINE INDEX 01 10 lt TIME SCHEDULE INDEX 01 10 STATUS gt NUMBER lsec gt 100ms 12 2 1 REGISTERING AND CHANGING TIME SCHEDULE TIME SCHEDULE A NO lt ENT gt gt DISPLAY CURRENT T S y SELECT T S NUMBER AND INDEX USE 278416 KEY lt ENT gt Y ENTER T S 8 DIGIT START TIME hh mm END TIME hh mm or lt ESC 32 YES or Error Star 505R PASS P505R TIME SCHEDULE You may program time schedules to grant and restrict access for each user There can be up to ten different schedules A minimum of one schedule must be defined If only one schedule is programmed the most common setting allows access for all users 24 hours day A time schedule can be programmed for each day of the week and holidays and five shifts can be defined for each day To set time schedules press lt ENT gt key from this menu If you want to set time schedules press lt ENT gt key when this figure is displayed T S 01 HOL 1 Press lt 2 gt key or lt 8 gt key to adjust the Time Schedule 00 00 00 00 T S number 1 10 and the day of th
6. Yes lt 1 gt key enter Yes Normal Operation Initialize Com Turn OFF Power Power off Tee Disconnect 3 wires pink cyan il black System initialization completion 10 2 HOW TO ENTER THE SET UP MENU To set up or to change the 505R settings you have to enter the SETUP MENU first To do so press the lt 0 gt key eight times for the Master ID Default setting 00000000 and the lt ENT gt key from the Keypad Then you can get into SETUP MENU There are four main SETUP MENUS and you first get into SETUP MENU F1 You can move to another SETUP MENU by pressing the lt F1 gt key for SETUP MENU F1 lt F2 gt key for SETUP MENU F2 lt F3 gt key for SETUP MENU F3 and lt F4 gt key for SETUP MENU F4 There are several SUBMENUS in the main SETUP MENU and you can scroll up and down the SUBMENU by pressing lt 4 gt and lt 6 gt key in the main SETUP MENU If you don t press any key for 60 seconds or if you press the lt ESC gt key 505R will exit the SETUP MENU and return to normal operation You can also change the Master ID in the SETUP MENU F1 19 Star 505R iPass P505R IDTECXK mTecx SR505 In the case of SR505 Press ten times the lt 0 gt key Default setting 0000000000 to enter the SETUP MENU 10 3 DATE AND TIME SETTING Select TIME SETTING in the SETUP MENU F1 and enter the Year Month Date Hour Minute Second Day Total 15 digits as shown below Th
7. as displaying wrong card numbers in the reader test mode Cause Reader defect wiring error between the reader and the controller or the electric noises 1 Be sure that the reader reads the card ID when you present a card 2 Be sure that the reader format is correct 26bit Wiegand or 34bit Wiegand for SR505 3 Check the wiring between the reader and 505R Check the wiring of Wiegand data lines DO and D1 Connect the controller ground to the ground wire of the reader and it is solution recommended to connect them to an earth ground 4 With an oscilloscope check the shape of signals from the reader at the controller side When noises are shown on the signals it is recommended to use shielded wires and the unused wires to the common ground You can also use repeaters 5 Check the maximum cable length which may be indicated on the reader manual 6 If the trouble remains after the procedure above contact a service center Keeps making buzzer sound beep beep beep or beeeeeeeep Cause Error in Installation Door status or Internal circuits 1 Check the door status It occurs in case that the door is opened over 20 sec after the proper door open time 2 Check the door contact sensor type it should be NO type 3 Check in IN OUT DEFINE of F2 the fifth Time schedule code 01 10 value of 15 output T S If the time schedule code is set between 01 up to 10 and if the present time is included in the schedule If
8. converter CNP200 is required to use RS422 communication between the 505R and a host computer Please follow the instructions 1 Connect R 422 TX Yellow wire of the 505R to RS422 RX port of the converter 2 Connect RS422 TX Grey wire of the 505R to RS422 RX port of the converter 3 Connect RS422 RX Blue wire of the 505R to RS422 TX port of the converter 4 Connect RS422 RX Brown wire of the 505R to RS422 TX port of the converter 5 Plug the RS232 9 pin connector of the converter into the COM1 or COM2 Port of the PC 6 Install and run the 505R Application Software 16 Star 505R pass P505R RS 422 232 CONVERTER RS232C T T K R ee ee To Star 505R To host PC a Between 505R and CNP200 b RS 422 port connection c CNP200 setting Figure RS 422 Communication between 505R and Host Computer 9 2 2 RS 422 CONNECTION MULTIPLE 505R CONNECTIONS RS422 RS232 converter is required to use RS422 communication between multiple 505R and a host computer Please follow the following instructions First you have to connect all RS422 port of all 505Rs in parallel 1 Connect RS422 TX Yellow wire of one 505R to RS422 TX Yellow wire of another 505R 2 Connect RS422 TX Grey wire of one 505R to RS422 TX Grey wire of another 505R 3 Connect RS422 RX Blue wire of one 505R to RS422 RX Blue wire of another 505R 4 Connect RS422 RX Brown wire of one 505R to RS422 RX B
9. equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the radio or television off and on the user is encouraged to try to correct interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on another circuit 4 Consult the dealer or an experienced radio TV technician for help 50 Star 505R iPass P505R 15 Warranty Policy and Limitation of Liability IDTECK warrants this product against defects in material and workmanship for the period specified below from the date of purchase under normal customer use This Warranty doesn t apply 1 to any product which has been dismantled without authorization of IDTECK or and has a damaged or detached QC label on its back side 2 to any losses defects or damages caused by improper testing operation installation maintenance modification alteration or adjustment 3 to any product with a damaged or faded serial number on it or 4 to any losses defects or damages caused by lightning or other electrical d
10. it is set to unintended value change it to 00 Programmable via PC software 4 If the trouble remains after checking the above contact a designated service center Solution SCHEDULE ERROR message shows when RFID card is read Cause Error in RFID card registration time schedule setting or the system itself 1 If the unit used to operate properly there has been an electric shock that damaged the internal memory and data Please initialize the unit as instructed in the manual 2 Check if ID information has been put in incorrectly during its registration Register ID again checking the following points In order to restrict access of the ID user for specific time zone as instructed in the manual register time schedule in advance and apply the time schedule code 1 10 in the registration of the user ID In order to allow the user to access at all times put in 00 3 Use software for time schedule setting as instructed in the software manual 4 If the trouble remains after checking the above contact a designated service center Solution ACCESS DOOR ERR message shows when the RF ID card is read Cause Incorrect user setting or false of internal circuit 1 If the unit used to operate properly maybe there has been an electric shock that damaged the internal memory and data Please initialize the unit as instructed in the manual solution 2 Check if ID information has been put in incorrectly du
11. key lt 4 gt or lt 6 gt 12 4 SETUP MENU F4 SRAM TEST SRAM TEST key lt 4 gt or lt 6 gt OUTPUT TEST OUTPUT TEST key lt 4 gt or lt 6 gt LCD TEST oe LCD TEST key lt 4 gt or lt 6 gt SEARCHING KEY lt 4 gt or lt 6 gt KEYPAD TEST KEYPAD TEST key lt 4 gt or lt 6 gt READER TEST READER TEST t key lt 4 gt or lt 6 gt INPUT TEST INPUT TEST key lt 4 gt or lt 6 gt COMMUNICATION TEST COMM TEST 20 12 4 1 VERSION CHECK VERSION The version of the controller s firmware is displayed on 505R V5 0 the LCD Press lt 4 gt or lt 6 gt key to look for other menus IDTECK 12 4 2 SRAM TEST SRAM TEST Memory fail 00 RAM testing RAM test pass Press any key 12 4 3 OUTPUT TEST Star 505R pass P505R IDTECx SR505 To test the SRAM memory press lt ENT gt key If the SRAM has problems LCD will show the memory block number with Memory fail message In this case you have to contact technical support Press any key to return to the setup menu If the SRAM is working properly the LCD will show RAM test pass message Press any key to return to the setup menu OUTPUT TEST lt ENT gt Relay 1 test Activated two times A y Relay 2 test Activated two times TTL Output I test Activated two times
12. selecting mode press ENT to complete setting NOT USE The value matched with the Function key will not be changed until another function key is pressed USE User can see OK under normal status and the value matched with Function key will be shown on certain time when function key is pressed WAIT TIME Time duration between the display of value matched with function to display OK default 12 1 15 DATA BYTE TYPE SETTING SR505 FUNCTION DATA BYTE TYPE 4BYTE DATA BYTE TYPE gt 2BYTE Card data management can be selected in this menu The default value is 4 BYTE and generally this value may not need to be changed If customer needs to add more units where SR505 V1 0 is installed the user needs to change the value to 2BYTE Otherwise please do not change this value 31 IDTECK 12 2 SETUP MENU F2 gt SEARCHING KEY lt 4 gt or lt 6 gt gt TIME SCHEDULE key lt 4 gt or lt 6 gt HOLIDAY DEFINE A key lt 4 gt or lt 6 gt y IN OUT DEFINE A key lt 4 gt or lt 6 gt y HOLIDAY INDEX key lt 4 gt or lt 6 gt MODE INDEX key lt 4 gt or lt 6 gt LCD DISPLAY key lt 4 gt or lt 6 gt OUTPUT TIME SET INDEX 01 10 Star 505R PASS P505R IDTECx SR505 lt WEEKLY HOL SUN MON SAT NO 01 05 INDEX 01 10 NO 01 32 lt 01 EXIT 03 INPUT 1 04 INPUT 2 05 TAMPER S
13. 12 1 1 READER 1 MODE SETTING READER 1 MODE lt ENT gt _ _ RF Only default READER 1 MODE RF ONLY READER 1 MODE gt RF ONLY READER 1 MODE gt RF PW READER 1 MODE gt PIN ONLY key lt 4 gt or lt 6 gt gt RF PASSWORD key lt 4 gt or lt 6 gt gt PIN 4 6 Digit READER 1 MODE is set to RF ONLY operating mode If you want to change the mode to RF PASSWORD operating mode press lt ENT gt key Now you can change the mode by pressing the lt 4 gt or lt 6 gt key to toggle the mode If you want to setup the mode displayed press lt ENT gt key to accept this mode Note RF ONLY The door is accessible with the proximity card alone RF PW The door is accessible with the proximity card and Password PIN ONLY The door is accessible with the PIN number 4 6 digits If you select PIN it will be affected to Reader 1 and 2 READER 2 MODE setup Is the same as above The SR505 doesn t have READER 2 MODE It is used RF PASSWORD mode only Reader 1 12 1 2 TIME SETTING TIME SETTING YYYYMMDDhhmmssW i Press lt ENT gt key and enter 15 digit Date Time codes then lt ENT gt key to finish setting YYYY Year MM Month DD Date hh Hours 24 hours system mm Minutes ss Seconds W Sun 1 Mon 2 Tue 3 Wed 4 Thu 5 Fri 6 Sat 7 Example 200302101330152 gt Feb 10 2003 13 30 15 Mon 12 1 3 ANTI PASS BACK MODE SETT
14. 14443 Type A Compatible serial Number Read Only 4 Specification Dual 8bit Microprocessor Memory Sogam 64KByte ROM Memory Data Memory 128KByte SRAM Battery back up se S 500 10 000 Users Event Buffer 2 500 7 250 Event Buffers IDK50 IMC125 Up to 2 inch 5cm IDC80 IDC170 Up to 4 inch 10cm Active Type IDA150 IDA200 Compatible Reading Time Card Read Passive Type Range Star 505R pass P505R IDTECK IDTECX SR505 Power Current DC 12V Max 350mA External 505R m Reader IP505R 1ea 26bit Wiegand 4 8bit Burst for PIN Port SR505 1ea 34bit Wiegand 4 8bit Burst for PIN RS232 RS422 RS485 Max 32ch Communication TCP IP External LAN Converter Required Baud Rate 9600bps Default 4800bps 19200bps and 38400bps Selectable Input Port 4ea Exit Button Door Sensor Aux 1 Aux 2 2ea FORM C Relay Output COM NO NC Output Port DC12V 18V Rating Max 2A 2ea TTL Output DC5V Rating Max 20mA Character LCD 2 Lines x 16 Char 2 62 x 0 55 65 6mm x 13 8mm Screen LCD o to 50 C 4320 to 122 sly ae Ai Temperature 35 to 65 C 31 to 149 F Operating Humidity 10 to 90 relative humidity non condensing Color Material Dark Pearl Gray Polycarbonate Dimension W x H x T 150mm x 120mm x 39 5mm 5 9 x 4 72 x 1 55 3979 0 88lbs Certification UL FCC CE MIC 5 Identifying Supplied Parts Please unpack and check t
15. 2 x 39 5mm 1 55 8 2 BACKUP BATTERY DIP SWITCH Star 505R has a switch for the backup battery connection which remains open circuit to prevent any current consumption of the backup battery Figure Switch setting Before the Star 505R operation it needs to be connected so that the backup battery can retain the memory during power failure SETTING A DIP SWITCH Figure DIP SWITCH SETTING Figure DIP SWITCH LOCATION 12 Star 505R iPass P505R IDTECK IDTECx SR505 8 3 SYSTEM INITIALIZATION Connect the cyan wire pink wire and black wire they are seen from the rear view together and power on the unit If you want hardware initialization press enter key lt 1 gt After initializing switch main power OFF separate the three wires pink cyan and black GND and switch the main power ON again Power on S If you turn on the system power af after connected 3 wires pink cyan and black GND you can enter Initialize OK into system initialize mode 0 NO 1 Yes o Normal Operation Initialize Com Turn OFF Power Power off Y Disconnect 3 wires pink cyan a black System initialization completion 8 4 INSTALLATION OF THE PRODUCT 8 4 1 Tear off page 56 and use the provided template to drill two 6 32 holes and one 1 2 hole on the proper location of the wall to mount the Wall Mount bracket as shown below Skip this step if
16. 2008 IDTECK Co Ltd
17. 3 EVENT MEMORY 15 FUNCTION KEY 23 16 DATA BYTE TYPE IDTECK Star 505R pass P505R IDTECX SR505 To setup or to change the 505R settings you have to enter the SETUP MENU first To do so press the lt 0 gt key eight times for Master ID Default setting 00000000 and lt ENT gt key from the Keypad Now you can get into SETUP MENU There are 4 main SETUP MENUS and you first get into SETUP MENU F1 You can move to other SETUP MENUS by pressing lt F1 gt key for SETUP MENU F1 lt F2 gt key for SETUP MENU F2 lt F3 gt key for SETUP MENU F3 and lt F4 gt key for SETUP MENU F4 There are several SUB MENUS in the main SETUP MENU You can scroll up and down the SUB MENU by pressing the lt 4 gt and lt 6 gt key in the main SETUP MENU If you don t press any key for 60 seconds or if you press lt ESC gt key 505R will exit the SETUP MENU and return to normal operation In the case of SR505 Press ten times the lt 0 gt key Default setting 0000000000 to enter the SETUP MENU 12 1 SETUP MENU F1 P READER 1 MODE gt RF Only DEFAULT gt RF P W PassWord key lt 4 gt or lt 6 gt gt PIN 4 6 Digit READER 2 MODE gt RF Only DEFAU
18. ING APB SETUP i NOT USE It sind back operation is not in use It only pplies when the door has an Exit Reader Star 505R aPASs P505R APB SETUP Press lt 4 gt or lt 6 gt key for searching the APB mode gt USE Press lt ENT gt key to select the mode NOT USE Anti pass back mode is not applied USE Anti pass back mode Is separately applied oA L P If you select All Clear 505R will clear all APB flags and all p ear users are not allowed Exit first 12 1 4 COMMUNICATION ID ADDRESS SETTING COMM ID SETTING This is the Communication ID setting menu To change the ID press lt ENT gt key The number on the LCD is the current communication ID Device No Press lt ENT gt key again to set a new COMM ID SETTING uy communication ID COMM ID SETTING When the cursor is blinking enter a new ID 01 two digit number then the setting is completed For the next setting use lt 4 gt and lt 6 gt keys Possible ID is between 00 31 inclusive 12 1 5 BAUD RATE SETTING BAUD RATE i CON100 supports 4800 9600 19200 and 38400bps of 9600 baud rate and default setting is 9600bps Wrong baud rate setting will cause communication errors and you have to set same baud rate to iCON100 and host PC If you have communication problem BAUD RATE please check followings gt 9600 Check COMM ID of iCON100 and host PC Check BAUD RATE of iCON100 and host PC Check commun
19. ION lt ENT gt _ gt REGISTRATION SELECT CARD or KEY CARD gt PRESENT CARD KEY amp y ENTER NEW ID ID REGISTRATION ERROR DISPLAY Invalid Card ID A Invalid T S 1 Invalid T S 2 Invalid RD a YES Card ID Error No lt v INPUT PW TS RD PW TS RD Error NO ID REGISTRATION END lt YES ID REGISTRATION i Press lt ENT gt key to register new User ID D Number is registered in the controller by RF cards or through the keypad For RF cards press lt 1 gt key the keypad lt 2 gt key or you can quit the registration by pressing lt ESC gt key Applicable for SR505 only ID REGISTRATION l Card 2 Key Applicable if 1 Cardis selected on SR505 or if Reader 1 Modeon 505R or IP505R is RF Only or RFAPW The reader is waiting for an RF card which has to be scanning registered The card number will appear with a beep as the card is read ID Applicable if 2Keyis selected on SR505 or if Reader 1 PW TS RD Modeon 505R or IP505R is PIN Only Te G Please enter the 6 digit ID manually For SR505 the ID number is 10 digits 123456 PW TS RD The second row on the LCD shows the fields for the 4 digit password SR505 only time schedule index and reader code Please enter the desired values in the NOTE For 505R or IP505R fields as explained below to finish registratio
20. LT RF P W Pass Word key lt 4 gt or lt 6 gt PIN 4 6 Digit TIME SETTING lt 15 digit key in key lt 4 gt or lt 6 gt SEARCHING KEY APB SETUP gt NOT USE DEFAULT lt 4 gt or lt 6 gt gt USE key lt 4 gt or lt 6 gt _ gt ALL CLEAR COMM ID key lt 4 gt or lt 6 gt BAUD RATE gt 4800 A gt 9600 DEFAULT key lt 4 gt or lt 6 gt gt 19200 38400 Yy EVENT CLEAR gt YES NO key lt 4 gt or lt 6 gt v MASTER ID CHANGE gt CARD T IDTECK SEARCHING KEY lt 4 gt or lt 6 gt Star 505R PASS P505R mTeck SR505 key lt 4 gt or lt 6 gt SYSTEM INITIALIZE gt YES key lt 4 gt or lt 6 gt a CARD ID CLEAR gt YES gt NO key lt 4 gt or lt 6 gt TIME SCHE CLEAR gt YES key lt 4 gt or lt 6 gt 22 RF PIN INPUT gt ENABLE p gt DISABLE DEFAULT key lt 4 gt or lt 6 gt EVENT MEMORY gt NOT USE key lt 4 gt or lt 6 gt NA USE DEFAULT DURESS MODE SET gt NOT USE DEFAULT A gt USE key lt 4 gt or lt 6 gt v DURESS P W SETTING FUNCTION KEY gt NOT USE DEFAULT key lt 4 gt or lt 6 gt nd USE DATA BYTE TYPE gt 2BYTE L 4BYTE DEFAULT IDTECK Star 505R pass P505R IDTECXx SR505
21. PLAY gt NUMBER 35 Star 505R pass P505R 12 2 7 OUTPUT TIME UNIT SETTING This menu is to define time unit of 5 output ports sec define time of output by second in the in out define 100 ms define time of output by 0 1 second 100ms in the in out define OUTPUT TIME SET 1sec Ex In order to have the relay 1 Out 1 operate for 3 second responding to the exit button input set as follow Define 1 Exit amp Relay as 03 in IN OUT define Define the OUTPUT TIME SET as second Ex In order to have the relay 1 Out 1 operate for 0 3 second responding to the exit button input set as the following OUTPUT TIME SET Define one Exit amp Relay as 03 in IN OUT define gt 100ms Define the OUTPUT TIME SET as 100ms 12 3 SETUP MENU F3 ID REGISTRATION gt CARD Key lt 4 gt or lt 6 gt ID DELETE gt ENTER ID Key lt 4 gt or lt 6 gt SEARCHING KEY its et 26s ID LIST gt DISPLAY REGISTERED ID Key lt 4 gt or lt 6 gt DISPLAY REGISTRATION REGISTERED ID COUNT gt ID COUNT Key lt 4 gt or lt 6 gt ENTER POSSIBLE ai wA ID COUNT gt REGISTRATION ID COUNT A ID EVENT 500 7 250 1 000 7 000 1 500 6 750 2 000 6 500 2 500 6 250 3 000 6 000 9 000 3 000 AA 36 10 000 2 500 Star 505R iPass P505R 12 3 1 CARD REGISTRAT
22. R 505R F1 J p MASTER ID lt ENT gt Press lt F3 gt lt 4 gt or lt 6 gt 01 20 09 00 33 l R 8 times lt 0 gt lt ENT gt Select ID COUNT ID COUNT lt ENT gt ENTER ID COUNT lt ENT gt Eg 5 000 gt o Ed 10000 Ed gt m Enter the number from 500 to 10000 ID COUNT STAR 505R F1 _ gt 10 000 gt 01 20 09 01 16 Star 505R aPASs P505R You will see this error message when you press EVENT MEMORY lt ENT gt key in the ID COUNT menu It tells you NOT EMPTY that some events are still existing in the EVENT Buffer and you may lose the data if you change the ID COUNT You may try this setting again after uploading the events to the host PC or deleting them using the SETUP MENU F1 EVENT CLEAR You will see this error message if you try to change ID TOTAL COUNT ID COUNT less than the total registered User IDs Wrong In this case you have to delete some User IDs or clear them all using the SETUP MENU F1 gt ID CLEAR first then try again from the beginning 10 5 ID REGISTRATION You can register the User ID into the 505R Select SETUP MENU F3 gt ID REGISTRATION and follow the steps below For 505R or IP505R registration can be done either with RF cards or via keypad input depending on the Reader 1 Mode setting The Master ID for SR505 is a ten digit number Default setting 0000000000 gt MASTER ID ENT gt STAR 505R F1 i Press lt F3 gt th
23. RMINATION RESISTOR Termination resistors are used to match impedance of the network to the impedance of the transmission line being used When impedance is mismatched the transmitted signal is not completely absorbed by the receiver and a portion of signal is reflected back into the transmission line The decision whether or not to use termination resistors should be based on the cable length and data rate used by the communication system For example if you use 9 600 baud rate and 1 200m length of cable the propagation velocity of cable is 0 66 x speed of light This value is specified by the cable manufacturer if we assume the reflections will damp out in three round trip up and down the cable length the transmitted signal will stabilize 18 6us after the leading edge of a bit Since the data bit is captured in the middle of the bit which is approximately 52us after the leading edge of a bit The reflection stabilizing time 18 6us is much before the center of the bit therefore the termination resistors are not required However if you install the cable to maximum length the impedance of cable and network is mismatched and the transmitted signal is overlapped by the reflected signal In this case it is recommended to add termination resistors to the end of the receiver lines A 120Q resistor can be used for termination resistor in parallel between the receiver lines A and B for 2 wires RS485 system or RX and RX for 4 wir
24. Reader to DC 12V 2 Connect wire of the Proximity Reader to GND of Power 3 Connect Data 0 wire of the Proximity Reader to DO the Pink wire 4 Connect Data 1 wire of the Proximity Reader to D1 the Cyan wire Compatible Readers 505R iP 505R Standard 26bit Wiegand Format Proximity Readers Standard 26bit Wiegand 8bit Burst Format Proximity and Keypad Readers SR505 Standard 34bitWiegand Format Proximity Readers Standard 34bitWiegand 8bit Burst Format Proximity and Keypad Readers Recommended Readers 505R RF TINY RF10 RF20 RF30 RFK101 FGR006 FGROO6EX iP 505R iP10 iP20 iP30 iPK101 SR505 SR10 SR20 SR30 SRK101 FGROO6SR FGR006SRB 15 Star 505R PASS P505R 9 Communications 9 1 RS232 COMMUNICATION PORT CONNECTION A 9 pin connector Serial communication connector female is required to connect the 505R to a host computer via RS232 communication Please follow the instructions 1 Connect RS232 TX Black wire with White stripe wire of 505R to the pin 2 RX of the 9 pin connector 2 Connect RS232 RX Red wire with White stripe port of 505R to the pin 3 TX of the 9 pin connector 3 Connect GND Black wire of 505R to the pin 5 of the 9 pin connector 4 Plug in the 9 pin connector to COM1 or COM2 Port of the host PC 5 Install and run 505R Application Software Figure RS232 COMMUNICATON 9 2 RS 422 COMMUNICATION PORT CONNECTION 9 2 1 RS 422 CONNECTION STAND ALONE RS422 RS232
25. Relay 1 will open for 3 seconds Default with the Green LED on Exit Button To request an exit from the inside an Exit Button or an Exit Reader can be used The Door Relay 1 will open for 3 seconds with the Green LED on Alarms When an unregistered card is read the access is denied and the alarm Relay 2 will be activated for 3 seconds with the Yellow LED on 11 2 DEFAULT SETTING When you operate the 505R for the first time or want to initialize the 505R the controller will setup all value defaults factory settings You can change the settings for the desired application Please refer to the APPENDIX for the default setting values 12 Setting Changes INITIAL DISPLAY MODEL NAME CURRENT TIME gt 90 vrs YES a NO af OPERATE GENERAL YES MODE y SETUP MODE SETUP F1 MODE SETUP F2 MODE SETUP F3 MODE SETUP F4 MODE 1 READER 1 MODE 1 TIME SCHEDULE 1 ID REGISTRATION 1 VERSION 2 READER 2 MODE 2 HOLIDAY SETTING 2 ID DELETE 2 SRAM TEST 3 TIME SETTTING 3 IN OUT DEFINE 3 ID LIST 3 OUTPUT TEST 4 APB SETUP 4 HOLIDAY INDEX 4 REG ID COUNT 4 LCD TEST 5 COMM ADDRESS 5 MODE INDEX 5 ID COUNT 5 KEYPAD TEST 6 BAUD RATE 6 LCD DISPLAY 6 READER TEST 7 EVENT CLEAR 7 OUTPUT TIME SET 7 INPUT TEST 8 MASTER ID CHANGE 8 COMM TEST 9 SYSTEM INITIALIZE 10 CARD ID CLEAR 11 TIME SCHE CLEAR 12 RF PIN INPUT 1
26. Setup mode Note that all the value will be set to default including the IDs after initializing 3 If the trouble remains after the procedure above contact a service center No problem with accessing by card but cannot access with the PIN input Cause An error in Setup or possible component defect 1 Check whether a beep sound is generated when you press a key When a beep sound is generated the problem may be an error in setup Proceed like followings Enter the Master ID 00000000 default to enter the Setup mode Si Note that the Master ID for SR505 is 10 times lt 0 gt O000000000 Press lt F1 gt key READER 1 MODE will appear on the LCD then use the key lt 6 gt to choose RF_PIN_INPUT and select Enable as wanted 2 When there is no beep sound or already enabled Key in functions contact a designated center Can set the controller to operate in RF only mode for 1 card and in RF P W mode for another Cause N A ATA 1 Do not mix the working mode for one Reader 2 1 reader can be set to operate in RF only mode and another one in RF P W mode The Setup mode suddenly goes back to the Normal operating mode Cause Time out error In the Setup mode it is programmed to do so when there is no key in or reading card Solution jak within 60 seconds 47 Star 505R iPass P505R The reader seems to read cards but the controller does not respond or does not respond properly such
27. User s Manual Star 505R pass P505R IDTECX SR505 Proximity amp PIN Time amp Attendance Access Controller IDTECX Star 505R iPASS P505R IDTECX wreck SR505 Table of Contents 1 Important Safety INStrUCTIONS 6a 615 6a sanasana sanasana nana KAKA KANIKI KAKA KAKA KI KINUKIE NWAKA KARAKANA 3 WA III 3 Si AA 4 A SD CCING GUGM AAA AAA AAA AAA i a i ii i i i ii i 4 5 Identifying Supplied Parts AA 5 D Product OVELVIEW AAA 6 7 Installation Checkpoint amp TIPS 9 Oz INSTANAUON AA 12 SCOMMUNICAUONS AAA 16 10 B a51 SQUINGS AAA 19 ILS OC AO LS AUA 23 12 Setting CHANGES AAA 23 PSs FGI GIN AKAA 45 14 FCC Registration Information ssssssssssssssecesesecseseseesecseseeseceseseesesseseeses 50 15 Warranty Policy and Limitation Of Liability sssi 51 LA AAA 53 Star 505R iPass P505R IDTECK IDTECX SR505 1 Important Safety Instructions When using Standalone Network Proximity Access Controller basic safety precautions should always be followed to reduce the risk of fire electrical shock and injury to persons In addition the following safety guides should also be followed 1 Fully read and understand all instructions and follow them completely 2 Follow all warnings and instructions marked on the product 3 Do not use liquid or aerosol cleaners Use a damp cloth for cleaning If necessary use mild soap 4 Do not use this product near water 5 Only operate this product using the type of power sou
28. an Auxiliary Input Device to one of the Input 1 2 Connect the other wire from the Auxiliary Input Device to GND SENSOR INPUT DEVICE CONNECTION STAR SUSE DOOR SENSOR 4 GND T Yellow wire with Red strip EXIT BUTTON DC12V 2 5A Min ile LE Figure INPUT DEVICES CONNECTION 8 5 3 OUTPUT CONNECTIONS Door Lock Power Fail Safe Connection Relay 1 Connect COM wire of Relay 1 the Gray wire with Red stripe to 12V Connect NC wire of Relay 1 the Blue wire with White stripe to wire of door lock device Connect GND wire to wire of door lock devices 14 Star 505R iPass P505R IDTECK IDTECx SR505 Door Lock Power Fail Secure Connection Relay 1 Connect COM wire of Relay 1 the Gray wire with Red stripe to 12V Connect NO wire of Relay 1 the White wire with Red stripe to wire of door lock device Connect GND wire to wire of door lock devices Alarm Device Connection Relay 2 1 Connect COM wire of Relay 2 the White wire to 12V 2 Connect NO wire of Relay 2 the Purple wire to wire of Alarm devices 3 Connect GND port to wire of Alarm devices POWER RELAY 1 FAIL 5AFE FAILSECURE Figure DOOR LOCK ALARM DEVICE CONNECTION CAUTION Please add one DIODE as shown above DIODE Fast recovery DIODE current Min 1A 1N4001 1N4007 or similar 8 5 4 EXTRA READER CONNECTIONS Proximity Reader Connection 1 Connect wire of the Proximity
29. and lt 6 gt key select the index for the days 1 32 Press lt ENT gt key and the cursor will blink Enter the date in form of the Month 1 12 The LCD will indicate the defined date Now a day has been registered For further registration repeat the process To end registering the days press lt ESC gt key to return to the setup menu SELECT INDEX USE 4 6 KEY lt ENT gt y ENTER NEW TIME OR T S INDEX 10 DIGIT OR EVEN DIGIT ENT IN OUT DEFINE 1 EXIT 03 00 00 00 00 YES or Error You can program or deactivate each output to be generated and choose how long in seconds they will last There are default values as seen in the table 2 below Select input sources by changing Index numbers with the keys lt 4 gt or lt 6 gt Press lt ENT gt key and you will see a cursor blinking at the first digit from the left of the five couples of digits which corresponds to Relay1 Relay2 TTL1 TTL2 and Buzzer respectively Enter the delay times refer to the table below one by one An input output definition has been completed now For further definition repeat the process To end defining inputs outputs press lt ESC gt key and you will see the first figure of the menu Note The five couples of digits of Output T S 15 and Input Outypt T S 16 are time schedule indexes Star 505R pass P505R 12 2 4 HOLIDAY INDEX SETTING Holiday Index is to link the H
30. are to enter eight L l digit number Eight digit ID 00000000 99999999 XXXXXXXX Enter a new Master password four digits and finish Registered changing by pressing the lt ENT gt key Master Card The figure indicates that changing of the Master ID has Registered been finished successfully The Master ID for 505R is 10 digits number Default setting 0000000000 12 1 8 SYSTEM INITIALIZE SYS INITIALIZE i This operation will initialize the 505R Press lt ENT gt key if an initialization is needed First time installation or resetting in the event of a malfunction CAUTION Initializing will erase all stored data in the memory SYS INITIALIZE Press the lt 1 gt key to initialize or lt 0 gt key to cancel 1 Yes 0 No the operation 28 Star 505R aPASs P505R System i This message appears while the system is being Initializing initialized After the initialization 505R will return to the Setup menu 12 1 9 CARD ID CLEAR CARD ID CLEAR When you want to delete all User IDs Card IDs you can clear all User IDs from the memory Press lt ENT gt key then press the lt 1 gt key to clear all User IDs or lt 0 gt key to cancel the operation CARD ID CLEAR CAUTION Before Clearing all User IDs make sure that the registered User ID is no longer used 1 Yes 0 No otherwise you may lose all registered User IDs 12 1 10 TIME SCHEDULE CLEAR TIME SCHE CLEAR When you wan
31. d earth ground nearby then connect one end of shield wire to earth ground If you do not have earth ground nearby then find chassis ground and connect one end of shield wire to chassis ground If you do not find both earth ground and chassis ground then connect one end of shield wire to power ground GND of Star 505R Note that if the chassis ground is not properly connected to the earth and floated from the ground level then grounding to the chassis ground will give the worst communication in this case we recommend to using power ground instead of chassis ground RS422 Rs232 Convener Communication wires i R5422 Cable gt Shield wire open Earth Ground or Chasis Ground or Power Ground 205R 1 SOSE 2 Figure Grounding system 11 Star 505R PASS P505R IDTECK mTecx SR505 7 2 4 REVERSE DIODE CONNECTION If you connect an inductor Door Locks or Alarm device to the output relays there will be a high surge voltage created while the inductor is turning on and off If you do not connect reverse diode the surge voltage will transfer and damage to the electronic circuit of the controller It is strongly recommended to add a reverse diode between the inductor coils to absorb this surge voltage DC Cathode Anode A rs D a 1N4004 1N4007 or equiv Lock Alarm Figure Reverse Diode connection 505R 8 Installation 8 1 DIMENSIONS Unit mm inch 150mm 5 9 x 120mm 4 7
32. e LCD will display the new Date and Time after the time setting completed but the year and day will not be displayed 505R has a 24 hours system and day codes are 1 for Sunday 2 for Monday 3 for Tuesday 4 for Wednesday 5 for Thursday 6 for Friday and 7 for Saturday The Master ID for SR505 is a ten digit number Default setting 0000000000 STAR 505R F 1 gt MASTER ID 4 lt ENT gt gt R 01 01 00 00 15 Select TIME SETTING gt ERE p 8times lt 0 gt lt ENT gt 2 p gt lt ENT gt Initial Display TIME SETTING lt ENT gt YYYYMMDDhhmmssW lt ENT gt gt 200301200900005 gt Y ear Month Day Hour Min Sec Day TIME SETTING AES STAR 505R F1 d gt gt 01 20 09 00 00 LCD displays after time setting 10 4 ID COUNT SETTING 505R can register maximum 10 000 User IDs and you can select maximum User IDs to be registered into the 505R from 500 Users up to 10 000 Users by every 500 unit This ID COUNT setting is to configure maximum User ID to be registered into 505R and if you setup less ID COUNT 505R will increase the EVENT Buffer size to maximum The default ID COUNT is 9 000 Users and the default EVENT Buffer size is 5 000 It can be stored when you operate 505R off line Select ID COUNT in the SETUP MENU F3 then setup the maximum User IDs to be registered into 505R Follow the steps to setup the ID COUNT The Master ID for SR505 is a ten digit number Default setting 0000000000 STA
33. e S W The parameters at the S W should be set as following Parity bit NONE Data bit 8 bits Stop bit 1 bit 2 Check the line connection for communication RS232 RS422 Single Drop onverter The RS232 cable from Solution the converter PT OO MX O RX O con oe ee T The RS232 cable from the converter 3 In case of setting RS422 communication we recommend to use line end resistors of 120 Ohm between the RX and RX lines and between the TX and TX lines Apply the same resistors to the converter RS422 lines Consult a service center or an electric technician if you are not sure how to do it 4 When a multi drop communication doesn t work test 1 to 1 communication first Cause 49 Star 505R iPass P505R 14 FCC Registration Information FCC REQUIREMENTS PART 15 Caution Any changes or modifications in construction of this device which are not expressly approved by the manufacturer for compliance could void the user s authority to operate the equipment NOTE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may Cause undesired operation This equipment has been tested and found to comply with the limits for a Class A Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to this
34. e week Mon Sun and HOL Define which shift of the day 1 5 using the lt 4 gt key and lt 6 gt key HOL refers to specific holidays you will register see 13 2 2 page 28 Press lt ENT gt key and the cursor will blink then enter the beginning time of the period in the form of hour 2 digit minute 2 digit and the ending time in the same form Then the lower line will indicate the defined period For more schedules repeat the process To end time scheduling press lt ESC gt key Possible values for time scheduling 1 Time schedule number 01 10 Needed when IDs are registered 2 A day of the week MON TUE WED THU FRI SAT SUN HOL 3 Index 1 5 referred to the five periods of time of a day 12 2 2 REGISTERING AND CHANGING HOLIDAY TIME SCHEDULE HOLIDAY T S lt ENT gt _ gt DISPLAY CURRENT T S r SELECT T S NUMBER AND INDEX USE 2 8 4 6 KEY lt ENT gt ENTER T S 4 DIGIT MM DD NO or lt ESC gt HOLIDAY T S i You can register up to 32 specified holidays per year for each schedule setting There can be 10 other registration sets created meaning holidays can be set for up to 10 UTU S Udy IDTECK HOL T S 01 01 00 00 A NO or lt ESC gt Star 505R pass P505R IDTECX SR505 i With the lt 2 gt key and lt 8 gt key select the Date Registration Set Number 1 10 and with the lt 4 gt key
35. en 01 20 09 01 23 Select _ eee gt 8times lt 0 gt lt ENT gt p ID REGISTRATION Initial LCD Display ID REGISTRATION ID REGISTRATION gt ENT gt Kard 2 Key This step appears only on SR505 1 Registration by RF Cards Applicable if E Cards selected on SR505 or if Reader 1 Mbdeon 505R or IP505R is RF Only or RF APW Approach card 123456 1 gt Scanning TE Reader PW TS RD Password 4 digits lt ENT gt i p Time Schedule codes lt ENT gt ID Registered Reader Usage codes lt ENT gt Reg completed Star 505R iPass P505R 2 Registration by Keypad Applicable if 2Keyis selected on SR505 or if Reader 1 Modeon 505R or IP505R is PIN Only 123456 9 gt PW TS RD gt ID 6digits lt ENT gt PW TS RD No PW field on 505R or IP505R Password 4digits lt ENT gt y Time Schedule codes lt ENT gt gt ID Registered Reader Usage codes lt ENT gt Reg completed 1 Scanning The reader is waiting for an RF card which has to be registered The card number will appear with a beep as the card is read ID number is a 6 digit number ID number of SR505 is a ten digit number 2 ID ID number consists of 4 6 digits ID numbers Enter 4 6 digits ID numbers and press lt ENT gt key in the ID field When the Reader mode is PIN it is displayed on the LCD NOTE An ID number of the SR505 is a 10 digit number 3 PW PW is the pa
36. er the Anti Pass Back mode can be set The Anti pass back mode prevents entry or exit when the registered user did not properly followed one entry and one exit by the Anti pass back rule The same user can not enter twice with the entry card without properly using the exit before Input Output The Star 505R has 4 built in inputs and 4 outputs 2 relay outputs and 2 TTL outputs which can be used to manipulate a wide variety of controls Time Schedule Setup You can program 10 time schedules and apply one time schedule to each User Each time schedule has 8 different time zones from Monday Sunday 7 time zones and one holiday Each time zone has 5 different time codes so you can program 5 different time codes to each day You can also program time schedules for individual inputs and outputs Note that the time schedule for input is activated time code for input device so that the input is activated during the time code on this time schedule Each time schedule is linked to one holiday schedule and this linked holiday only validates to the holiday time code of the time schedule Holiday Schedule Setup Excepting Sunday you can program 32 holidays to one holiday schedule Each holiday schedule is linked to one time schedule which has a time code for holidays You can program all holidays to a holiday schedule and the time code for holidays is programmed to the holiday time zone of time schedule Example A Holiday schedule 01 linked to time schedule 01 H
37. es RS422 system A termination resistor of less than 900 should not be used and no more than 2 terminations should be used in one networking system 7 2 2 HOW TO CONNECT TERMINATION RESISTORS RS485 RS232 Converter F Termination Resistors Last 504R Figure Termination resistors for 2 wire RS485 communication system 10 Star 505R PASS P505R RS422 RS232 Converter RS422 RS422 Termination Resistors Last 505R Figure Termination resistors for 4 wire RS422 communication system 7 2 3 GROUNDING SYSTEM FOR COMMUNICATION CABLE We recommend to using proper grounding system on the communication cable The best method for grounding system is to put the shield wire of the communication cable to the 1st class earth grounding however it is not so easy to bring the earth ground to the communication cable and also the installation cost is raised There will be three grounding point where you can find during installation 1 Earth Ground 2 Chassis Ground 3 Power Ground The most important point for grounding system is not to connect both ends of shield wires to the grounding system in this case there will be a current flow through the shield wire when the voltage level of both ends of shield wire is not equal and this current flow will create noise and interfere to communications For the good grounding we recommend to connecting ONLY one end of shield wire of communication cable to grounding system If you fin
38. he contents of the box Optional accessories if purchased may be included in the package O 0 o O Main Unit Wall Mount O ring User s Manual Diode lea lea 5ea 1 copy 2ea Star 505R iPASs P505R 6 Product Overview 6 1 Functions Stand Alone Operation The Star 505R is capable of having 2 readers 1 Door Control The unit receives card ID numbers from the proximity readers and determines whether or not to unlock the door When an input signal is entered for example from a Sensor activated or an Exit button pressed the controller generates and logs an appropriate response by input signals All events are stored into the memory buffers and sent to the host computer The access controller is a true stand alone device that in the event of malfunction will not affect other units when used in conjunction with one another Operation with Host Computer All event transactions can be managed via the host computer The data transmitted from the controller can be displayed and stored on the host PC Data Backup The controller retains all user information and event data for 30 days even in the case of power failure Xx CAUTION Battery switch must be set correctly before the unit running See the INSTALLATION section Keypad If the Star 505R is not connected to a host PC the integrated keypad and LCD display module can also be used for the entire programming process Anti Pass Back By using an additional proximity read
39. ication port and cable BAUD RATE Check COM port setup of host PC gt 19200 Parity None Data Bit 8 bit Stop Bit 1 bit To change the baud rate press lt ENT gt key and select desired baud rate by pressing lt 4 gt or lt 6 gt key then press lt ENT gt key 12 1 6 EVENT CLEAR EVENT CLEAR When the event memory is full or when you want to change ID COUNT you can clear the event memory in this menu Press lt ENT gt key then press lt 1 gt key to clear ave 8 or lt 0 gt key to ca a operation Star 505R aPASs P505R EVENT CLEAR x CAUTION Before you clear the events make sure 1 Yes 0 No that the stored events is not necessary to upload to the host PC otherwise you may lose important data 12 1 7 MASTER ID CHANGE MASTER ID CHANGE Press lt ENT gt key to change the current Master ID You should use the new Master ID to access the setup menu since the change is finished Master ID Number is registered in the controller by RF cards or through the keypad For RF cards Press lt 1 gt key the keypad lt 2 gt key or you can quit the registration by pressing lt ESC gt key MASTER ID CHANGE 1 Card 2 Key Scanning The reader is waiting for an RF card which is to be registered The card number will appear with a beep as the card is read After recognition the next message will appear i This figure appears when you press the lt 2 gt key for MASTER ID CHANGE through keypad registration then you
40. ine of LCD Press each key from the keypad The depressed key will disappear from the LCD Note that F1 key is A F2 key is B F3 key is C F4 key is D ESC key is E and ENT key is F on the screen After the test is done it returns to setup menu i Press lt ENT gt key for the reader test LCD will display Scanning for reading the cards Present the card to one of the readers When the reader successfully read the card LCD will display reader number and the 6 digit card number on the LCD Press lt ESC gt key to return to the setup menu ID number of SR505 is a 10 digit Decimal number Press lt ENT gt key for the input test The 5 digits shows the input status and 1 indicates that the input port is open circuit and 0 indicates that the input port is short to ground level S50 SCJ ITO J S OCLUD TITCT eee Star 505R iPass P505R IDTECXK IDTECx SR505 12 4 8 COMMUNICATION TEST COMM TEST Before this communication test connect the RS232 RX and RS232 TX wires together Then press lt ENT gt key TX data 0 This test is a loop test and 505R sends a character to COMN fail RS232 TX and check whether the RS232 RX receive the character or not If you have an error please contact our service facility COMM test pass After the test is done LCD will display COMM test Press any key pass Press any key to return to the set
41. ischarge natural disaster misuse accident or neglect This Limited Warranty is in lieu of all other warranties obligations or liabilities on the part of IDTECK and IDTECK DISCLAIMS ANY AND ALL WARRANTY WHETHER EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IDTECK does not and cannot know who is present what property is located where this product will be used it would be extremely difficult to determine the actual damages that may result from a failure of the product to perform as anticipated and the low price of this product is based upon the nature of the product provided and the limited liability that IDTECK assumes IDTECK IS NOT RESPONSIBLE FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR LOSS DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OR OTHER LOSS AND IDTECK S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT To obtain repair or replacement under the terms of this warranty visit IDTECK s Website http www idteck com and place an online RMA request After an RMA code is issued return the product along with the authorization RMA code gt gt Warranty Period Warranty item Period 1 RF READER FINGERPRINT READER 2 RF CARD Active type 3 STANDALONE CONTROLLER 2 years 4 CONTROL PANEL 5 FINGERPRINT CONTROLLER MOLDED RF READER 6 RF10 RF20 RF30 RF TINY IP10 IP20 IP30 SR10E SR10UE SR10SE SR10RWE SR10BE Lifetime RF CARD Passive t
42. l be deleted and display ID Deleted If the user ID is not found the display will show ID Unregistered You may repeat ID DELETE many times Press lt ESC gt key to exit the menu Star 505R gt pass P505R IDTECXK mTecx SR505 NOTE An ID number of the SR505 is 10 digits long 12 3 3 ID LIST ID usr lt ENT LCD display NO MEMORY EMPTY n DISPLAY ID NUMBER P W T S DOOR_FLAG lt ESC gt SEARCHING ID USE SEARCHING KEY ID LIST f you want to see the list of registered User IDs press the lt ENT gt key in this menu Enter 6 digit user ID 4 digit password the applied T S ID PELEK and the reader code is displayed on the LCD You can PW1234 TS00 RD3 scroll up and down the list by pressing lt 4 gt and lt 6 gt keys Press lt ESC gt key to return to the setup menu MEMORY i MEMORY EMPTY message will be displayed if there is EMPTY no registered User ID ID LIST TOP message will be displayed first when the ID LIST TOP first registered User ID is displayed on the LCD ID LIST BOTTOM message will be displayed first when ID LIST BOTTOM the last registered User ID is displayed on the LCD ID number of SR505 is 10 digits decimal number 12 3 4 REGISTERED ID COUNT REG ID COUNT This menu displays the total number of registered User 1234 ID It automatically counts WA you tagister or delete the memb IDTECK
43. n PW field doesn t appear during keypad registration IDTECK ID Registered 12 3 2 ID DELETE Star 505R pass P505R IDTECx SR505 1 PW Password the password used in RF password mode For 505R or IP505R this field does not appear during registration via keypad 2 TS Time schedule 00 Accessible at any time 01 10 Accessible according to each T S index 3 RD Reader code 1 for using Reader 1 only 2 for using Reader 2 only 3 for using both Readers 1 and 2 DELETE SELECT SLL 1 CARD 2 KEY A lt ENT gt y ENTER CARD NUMBER lt ENT gt i LCD Display ID DELETED Yes east LCD Display No UNREGISTERED ID ID DELETE Enter 6 digit ID that you want to delete and press lt ENT gt ID Number is deleted in the controller by RF cards or D DELETE through the keypad For RF cards press lt 1 gt key the Card 2 K keypad lt 2 gt key or quit the registration by pressing L 22 lt ESC gt key If Reader 1 Mode of 505R or IP505R is set to PIN only on it only operates in Key mode Scanning This figure appears when you press the lt 1 gt key Enter Card No ID Deleted The reader is waiting for an RF card which is to be deleted The card number will appear with a beep as the card is read i Enter 6 digit ID that you want to delete and lt ENT gt f the User ID you entered is found the User ID wil
44. n key Star 505R pass P505R IDTECx SR505 The Star 505R has four Function keys F1 F2 F3 F4 Card reading status LED When a card is read the card reading status LED turns on green Backup Battery DIP Switch Star 505R has a switch for the backup battery connection which remains open circuit to prevent any current consumption of the backup battery 6 2 2 WIRE COLOR TABLE OF THE Star 505R SIGNAL COLOR Main Power 12V Red Power Ground GND Black Door Relay Out COM Gray with Red stripe Door Relay Out NC Blue with White stripe Door Relay Out NO White with Red stripe Alarm Relay Out COM White Alarm Relay Out NC Purple with White stripe Alarm Relay Out NO Purple TTL Out 1 Orange with White stripe TTL Out 2 Brown with White stripe Exit Button In Orange Door Contact In Yellow with Red stripe Aux In 1 Green Aux In 2 Green with White stripe Wiegand Data 0 In Pink Wiegand Data 1 In Cyan RS232 TX Black with White stripe RS232 RX Red with White stripe RS422 TX Gray RS422 TX Yellow RS422 RX Brown RS422 RX Blue Please cut out tail connector before installation Star 505R ITENI aPASS P505R mTeck SR505 7 Installation Checkpoint amp Tips Installing the Star 505R is an easy task It can be installed with common hand tools and readily available communications wires This section provides informa
45. n powered on Cause SRAM backup battery problem or LCD module problem 1 Initialize the controller Connect the cyan wire pink wire and black wire together Switch the main power on and press lt 1 gt key Check if the LCD shows the message Initialize END turn off Power Switch main power OFF Separate 3 wires pink cyan and black GND Switch main power ON again Aware that all the default setting values will be restored and data memory will be cleared ID data clear Event data clear Time Schedule data clear etc 2 Set up the date and time on SETUP MENU F1 gt SYS INITIALIZE and SETUP MENU F1 gt TIME SETTING 3 If you still have problems please contact a designated service center Solution Randomly changed value of in out define from previously setting value after power reset Cause Discharge of RAM Back Up battery Problem during the main power off 1 Check if the Back Up Battery Jumper has been shortened 2 Check if the voltage of Back Up Battery is over 3 6V 3 If it is over 3 6V make initialization process as below Connect the cyan wire pink wire and black wire together Main power ON Enter key lt 1 gt Check if the LCD shows message of Initialize END turn off Power Main power OFF Separate 3 wire pink cyan and black GND Main power ON again Aware that all the default values are restored and data memory is cleared ID data clear Event data clea
46. ng requires no 3 Star 505R iPass P505R IDTECK IDTECx SR505 significant knowledge of access control or time amp attendance The three LED indicator lights inform you of the systems operating status at real time and the digital display acts as a programming aid as well as a regulation time clock By bundling the ultimate in high security access control and comprehensive employee management tools into a compact user friendly unit the field proven Star 505R is the ideal solution for controlling entrances and ensuring complete employee accountability 3 Features 125 KHz Standalone Proximity PIN Access Controller Dual Function for Access Control and Time amp Attendance Dynamic Control of Memory up to 10 000 Users 7 250 Event Buffers Standalone Network Communication via RS232 RS422 RS485 Max 32ch TCP IP External LAN Converter Required lea of External Reader Port for Anti Pass Back 26bit Wiegand and 4 8bit Burst for PIN Duress Mode Function Independent 4 Inputs and 4 Outputs Including 2 Form C Relay Outputs Dual Tamper Switches Alarm Event Monitoring using Tamper Switch by Application Software Compatible Software STARWATCH DUAL PRO II Comparison Table Built in 125KHz 4 Proximity Reader RF Only PIN 4 6digit Only RF P W 4digit ASK EM Format Built in 125KHz 4 Proximity Reader RF Only PIN 4 6digit Only RF P W ddigit Built in 13 56MHz 4 Proximity Reader IS0
47. oliday Schedule H S to Time HOLIDAY INDEX Schedule You can setup one Holiday Index 01 10 to one of T S Index 01 10 so that the Holiday Time Code in the T S can be applied for the holidays in the H S Default HOLIDAY CODE is 00 which means no holidays are applied to T S T S INDEX 01 select HOLIDAY INDEX menu and press lt ENT gt Select HOLIDAY CODE 00 desired T S_INDEX 01 10 by pressing the lt 4 gt or lt 6 gt key and press lt ENT gt key to input a 2 digits HOLIDAY CODE Press lt ENT gt to finish the setting 12 2 5 READER TIME SCHEDULE SETTING MODE INDEX i f you setup the RFtPASSWORD operating mode Refer to 00 MODE SELECTION you can apply the Time Schedule for MODE INDEX During the time period of Time Code in the T S Reader 1 will operate on RF ONLY mode The rest of time period Reader 1 will operate RF PASSWORD mode To apply this function you have to setup Time Schedules T S and Holiday Schedules H S MODE INDEX 00 select MODE INDEX then press lt ENT gt key Enter 2 digit 7 T S index 00 10 Press lt ENT gt key to apply 12 2 6 LCD DISPLAY TYPE SETTING LCD DISPLAY This function is to set STATUS CARD NUMBER the card STATUS reading from the Proximity and Keypad Readers STATUS The Fixed message is displayed on the LCD when card reading from the reader CARD NO The card number is displayed on the LCD when card reading from the reader Default setting is STATUS LCD DIS
48. oliday schedule 02 linked to time schedule 02 B Holiday schedule 02 linked to time schedule 01 Holiday schedule 01 linked to time schedule 03 Forced Door Open Alarm When the door is opened by force the door contact sensor will be activated The forced door open alarm will be generated until the door is closed again For this application you have to 6 Star 505R PASS P505R IDTECK IDTECX SR505 install the door contact sensor and properly set the door contact time and outputs to the alarm devices Duress Alarm In case of duress enter the 2 digits Duress Password and press the lt ENT gt key before the normal access process The door can be opened as normal but the duress alarm is also generated at the same time The duress alarm output will be activated to the TTL output and an alarm event will be sent to the host PC 6 2 Product Explanation 6 2 1 Front Panel Description LCD Display Card Reading Status LED System Operation Status LED 10 Numeric Keypad Function Keypad Figure Description of Star 505R Front Panel Setting a DIP Switch Figure Description of Star 505R Back Panel LCD Module LCD module display 505R status System Operation Status LED When the power is applied to 505R the red LED is turned on When the Relay 1 is operated the green LED is turned on When the Relay 2 is operated the yellow LED is turned on 16 key pad You can operate Star 505R manually by using the key pad 7 IDTELK Functio
49. r Time Schedule data clear etc 4 Define IN OUTPUT value as intend and keep the main power on more than 5 days 5 If after all the above the problem remains please contact a service center 46 Solution Star 505R PASS P505R IDTECK IDTECx SR505 A valid card became unregistered after batch downloading IDs from PC Cause Wrong procedure during download or a component defect 1 The card ID might be registered only to the controller and not registered in the PC During the process of downloading IDs 505R first erase the ID memory of the unit Saian therefore if the IDs from the PC didn t contain the card ID this can happen 2 Check whether the card ID is registered in the PC 3 If not please register the number and try downloading again 4 If the trouble remains after the procedure above contact a service center t doesn t enter the Setup Mode after entering the Master ID 00000000 Cause The Master ID might have been changed or components are defective 1 Try changing the Master ID through the application S W It ll be changed to 00000000 Note that the Master ID for SR505 is entering 10 times lt 0 gt 0000000000 2 When it is not feasible initialize the unit as following solution Press the two System Initialization switches simultaneously while power is on Wait until the message Initialize END Turn OFF Power appears on the LCD and turn it off and on again Try entering the
50. rce indicated If you are not sure of the type of power supplied to your installation site consult your dealer of local power company 6 Never insert objects of any kind into the product or through the cabinet slots as they may touch voltage points and or short circuit parts possibly resulting in fire or electric shock Never spill liquid of any kind on the product 7 Never disassemble this product by yourself take the unit to a qualified service center whenever service or repair is required Opening or removing the covers may expose you to dangerous voltages or other risks Also incorrect reassembly can cause electric shock when the unit is subsequently used 8 Unplug this product from the Direct Current DC power source and refer to qualified service personnel under these conditions a When the power supply cord or plug is damaged or frayed b If liquid has been spilled on the product c If the product does not operate normally after following the operating instructions in this manual Adjust only those controls that are covered by the operating instructions in this manual Improper adjustment of other controls that are not covered by this manual may damage the unit and will often require extensive work by a qualified technician to restore normal operation d If the product exhibits a distinct change in performance 2 General The Star 505R is a highly advanced intelligent single door controller with a dual 8bit microprocessor to
51. ring its registration Register ID again and check the following points Since the controller has two reader ports define RD door for the user to be allowed to access Reader1 only 1 Reader 2 only 2 Reader 1 amp 2 both 3 48 Star 505R iPass IP505R If RD is set as 1 the door opens only when the card is read at Reader 1 but not at Reader2 If it is read at Reader 2 ACCESS DOOR ERROR message shows up If RD is set as 2 only when the card is read at reader 2 the door opens but not at reader If it is read at reader 1 ACCESS DOOR ERROR message shows up If RD is set as 3 reader 1 amp 2 both open each door 3 Use software for time schedule setting in case it is connected to a PC shown as in the software manual 4 If the trouble remains after checking the above contact a designated service center The controller does not communicate with the Host PC A defective cable is used errors in wiring an error in setting COMM ID of the controller or damage on the COMM port either on the PC or on the controller side 1 Please check the settings of the application S W and the controller Check if the controller s COMM ID is listed on the application S W Set the different COMM ID when two or more controllers are installed Check if the baud rate 9600bps default is the same as the setting on the S W Make sure that the PC s COM port is set correctly on th
52. rown wire of another 505R Second you have to connect one of RS422 port of 505R to RS422 RS 232 converter 1 Connect RS422 TX Yellow wire of the one 505R to RX port of the converter 2 Connect RS422 TX Grey wire of the one 505R to RX port of the converter 3 Connect RS422 RX Blue wire of the one 505R to TX port of the converter 4 Connect RS422 RX Brown wire of the one 505R to TX port of the converter 17 aa AA _ _ a Star 505R iPass P505R IDTECK IDTECX SR505 5 Plug the RS232 9 pin connector of the converter into the COM1 or COM2 Port of the PC 6 Install and run the 505R Application Software RS 422 232 CONVERTER T T R OOO sows Figure RS 422 Communication between 505Rs and Host Computer 9 3 DIAL UP MODEM Please read the Software manual 9 4 TCP IP CONVERTER EXTERNAL VERSION Please read the Software manual 18 Star 505R iPASs P505R 10 Basic Settings 10 1 INITIALIZATION OF 505R Connect the cyan pink and black wires they are seen from the rear view together and Power on the unit If you want hardware initializing press Enter key lt 1 gt After initializing Put the main power OFF and separate 3 wires Pink cyan and black GND Afterwards put main power ON again Power on If you turn on the system power after connected 3 wires pink cyan and black GND you can enter Initialize OK into system initialize mode 0 NO 1
53. ssword which can be used to access the doors where you install a Proximity and Keypad Reader and setup the RF Password operating mode But regardless of the operating mode it is necessary to enter a default password 0000 in the PW ___ field when you register an ID NOTE For 505R or IP505R this field does not appear during registration via the keypad 4 TS TS is the Time Schedule code 00 10 TS is the Time Schedule for the Reader 1 Reader 2 When you present the card to a Reader the cardholder is only allowed the access of the door during the Time Schedule code entered to TS__ To control the accessible Time Schedule for each cardholder you must setup the Time schedules first and enter the Time Schedule code here If you want to access the door anytime for the cardholder then enter default Time Schedule code 00 for the value 5 RD__ RD is the Reader Usage code for the cardholder If you put in 1 for RD Reader 1 is accessible and if you put 0 for RD the cardholder can not access through the Reader 1 Reader 2 505R generates an error message Access Door Error and displays it on the LCD To get access through all Readers you have to put in 3 as a value for RD 22 Star 505R PASS P505R IDTECK IDTECx SR505 11 Operations 11 1 NORMAL OPERATION Power on When the power is applied to 505R the Red LED is turned on Registered card reading When a registered card or PIN is read the Door
54. t to delete all Time Schedules 01 15 you can clear them from the memory Press lt ENT gt key and press the lt 1 gt key to clear all T S or lt 0 gt key to cancel the operation x CAUTION Before you clear all T S make sure that KAA Ai v S the stored T S is no longer used otherwise you may lose all stored T S in the memory 12 1 11 KEYPAD INPUT SETTING RF PIN INPUT This function is to DISABLE ENABLE the keypad inputs DISABLE from the Proximity and Keypad Readers The default setting is to DISABLE the keypad inputs If you install the Keypad Reader 8bit burst format and set this mode to ENABLE you can access the door by pressing a 6 RF PIN INPUT digit User ID with the keypad gt ENABLE Press lt ENT gt key and press lt 4 gt or lt 6 gt key to select gt ENABLE then press the lt ENT gt key to setup this function 12 1 12 EVENT MEMORY SETTING EVENT MEMORY You can select whether you will use event memory or not USE When you select USE and in case of an event memory 505R generates an error message and keeps all events stored in the memory When you select NOT USE 505R will not generate an error and new event overwrite into the event buffers If you use 505R for standalone just for gt NOT USE A select NO EVENT MEMORY N NAZI v Star 505R iPass P505R 12 1 13 DURESS MODE SETTING lt ENT gt y DURESS MODE SET lt ENT 7 NOT USE default
55. the gang box is already installed on the wall 6 32 hole 1 55 39 5mm 1 85 47mm Fl wi L T Eh j 2 05 52mm 1 52 38 5mm 152 38 5mm 3 03 77mm 13 Star 505R PASS P505R IDTECK mTecx SR505 8 4 2 Using 2 screws install wall mount to the wall x CAUTION Before mounting the STAR 505R unit to the Wall Mount bracket operational test of the unit should be completed as the locking pins will lock the unit to the Wall Mount Removing the unit from the Wall Mount bracket after they have been installed together may cause damages to the bracket and render its effectiveness 8 4 3 Insert 5 O rings to the wall mount as indicated then route the cable of the main unit through the center hole and push the main unit to wall mount to lock the main unit and make sure that the main unit is locked with wall mount 8 5 WIRING 8 5 1 POWER Connect wire of DC 12V power to the Red wire Connect GND wire of DC 12V power to the Black wire 8 5 2 INPUT CONNECTIONS Exit Button Connection Connect one wire from an Exit Button to the Orange wire Connect the other wire from the Exit Button to the GND Door Contact Sensor Connection Connect one wire from a Door Contact Sensor to the Yellow wire with Red stripe Connect the other wire from the Door Contact Sensor to GND Auxiliary Input Connection Applied to Aux Input 1 Green wire Aux Input 2 Green wire with White stripe Connect one wire from
56. tion about wiring wire runs and other information to make the installation quick and easy 7 1 CHECK POINTS BEFORE INSTALLATION 7 1 1 SELECTION OF CABLE system installation cabling will be configured as follow 5232 RS422R 232 D amp Converter HOST P C SS DC12V DC12V Power Supply Power Supply RF Reader l Alum Sensor Input RF Reader Lock Alarm Sensor Input Figure System Installation Layout 7 1 2 RECOMMENDED CABLE TYPE AND PERMISSIBLE LENGTH OF CABLE Distance TD 505R Power DC12V Belden 9409 18 AWG DC Power gt 505R 2 conductor unshielded Belden 9512 22 AWG Reader Power and Data 4 conductor shielded Extra Reader gt 505R Belden 9514 22 AWG taun 8 conductor shielded Star 505R iPass P505R IDTECX IDTECK EFH Exit Button 4 4 conductor shielded shielded Sensor Input Belden ae 22 AWG Input gt 505R 8 conductor shielded D Door Lock Alarm Device Belden 9409 18AWG Lock Alarm gt 505R 2 conductor unshielded RS232 Cable Belden 9829 24 AWG Converter gt Host P C 2 twisted pair shielded RS485 Cable Belden 9829 24 AWG 505R gt 505R Sp 505R gt Converter 2 twisted pair shielded 1 200m RS422 Cable Belden 9830 24 AWG 505R gt 505R 3 twisted pair shielded 505R gt Converter in Need thicker wire if you connect the reader with high current consumption 7 2 CHECK POINT DURING INSTALLATION 7 2 1 TE
57. up menu Star 505R iPass P505R IDTECK IDTECx SR505 13 Appendix A THE RELATION BETWEEN INPUT AND OUTPUT DEFAULT 1 The relation between Input and Output Index No Relay 1 Relay 2 BUZZER 3 AUX 1 4 AUX 2 5 Tamper S W 6 Reader1 ID OK 7 Reader ID Error 8 Reader1 ID T S Error 9 Reader1 APB Error 10 Reader2 ID OK 11 Reader2 ID Error 12 Reader2 ID T S Error 13 Reader2 APB Error 14 DURESS MODE 15 OUTPUT TIME SCHEDULE 16 INPUT TIME SCHEDULE Index No 1 14 The value indicates operation time second of each output for the input signal Index No 15 The value indicates time schedule code index that each output operation is to be applied Index No 16 The value indicates the time schedule code index that each input 1 Exit button 5 Tamper S W operation is to be applied 45 Star 505R PASS P505R IDTECK mTeck SR505 B TROUBLE SHOOTING System operates abnormal Of that user mistake memory SRAM is damaged or the system is defective of the device 1 Check BAT connection Switch place template hole of reverse side You have to push up the Switch and system initialize before system installation Cause SETTING A DIP SWITCH Before After Figure DIP SWITCH SETTING Figure DIP SWITCH LOCATION 2 If the trouble remains after checking the above contact a designated service center Broken or abnormal letters shown on the LCD whe
58. ype 7 IDC80 IDC170 IDK50 IMC125 LXK50 IPC80 IPC170 IPK50 ISC80 ISC80S ISK50 IMC135 IHC80 IP100 IP200 51 Star 505R iPass P505R RMA REQUEST FORM IDTECK accepts only on line RMA requests on our Website www idteck com Please provide us with basic information in the below form so that we can understand your problems better Send us back this form with your products after an RMA code is issued on our Website This form is not compulsory Authorization RMA Code 1 Company Name 2 Model Name 3 Serial No 4 Original Invoice No 5 Distributor 6 Purchasing Date 7 RMA Request Date Please check your problems o Card Reading o Power o Keypad a Communication o Relay o LCD o LED amp Buzzer o Registration o Others IDTECK RMA Center gt gt 3F 10 10 1 10 2 Dodang Dong Weonmi Gu Bucheon Si Gyeonggi Do 157 030 Korea Telephone 82 2 2659 0055 HQ 82 32 671 5642 RMA Center Fax 82 2 2659 0086 HQ 82 32 671 5641 RMA Center Website www idteck com e Training Center www idtecktraining com 52 Star 505R aPASs P505R 16 Template P 12 hole 53 Star 505R PASS P505R The specifications contained in this manual are subject to change without notice at any time 5F Ace Techno Tower B D 684 1 Deungchon Dong Gangseo Gu Seoul 157 030 Korea Tel 82 2 2659 0055 Fax 82 2 2659 0086 E mail webmaster idteck com MAM505R HE 5X Jan 2008 Copyright 0
Download Pdf Manuals
Related Search