User Manual - Westinghouse
Contents
1. IMPORTANT INFORMATION ANTENNA INSTALLATION SAFETY Outdoor Antenna Grounding If an outside antenna or cable system is connected to the LED TV be sure the antenna or cable system is grounded to prevent voltage surges and built up static charges Article 810 of the National Electrical Code ANS NFPA 70 provides information on proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode Antenna Grounding According to the National Electrical Code ANSI NFPA 70 Antenna lead in wire Antenna discharge unit Grounding clamps NEC Section 810 20 Grounding Conductors Electric service LEA NEC Section 810 21 equipment 7 2 n gt 1 Power service grounding rounding clamps electrode system NEC National Electrical Code NEC Art 250 part H Lightning For added protection for the LED TV during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system DO NOT disconnect the antenna or the power cord during a heavy storm lightning may strike while you are holding the cable cord causing serious injury Turn off the LED TV and wait for the weather to improve Power lines An outside antenna system should not be located in the vicinity of overhead power lines or other2. 0000 cc cece eee 16 ANTENNA CONNEC TION susi ir 17 OUTDOOR ANTENNA CONNECTION 05 17 TABLE OF CONTENTS CABLE TV CTV DTV CONNECTION o 17 EXTERNAL DEVICE CONNECTIONS cccccccccecerseeeees 18 POWER CONNECTION ccccccccecscccsesceceesscecstececsteeees 20 CONNECTING AC POWER ieee 20 INITIAL SE TUD tummasta naa Paid usta Vs em s 20 BASIC OPERATIONS cccccccesccccecscecetscecetseceestsceeeeeeees 21 TURNING THE POWER ON AND OFF 21 ADJUSTING THE VOLUME aeoea 21 CHANGING CHANNELS cccccccsescecsescceceececeeeeeees 22 SELECTING THE INPUT SOURCE 22 ADJUSTING THE DISPLAY FORMAT aa 23 ADJUSTING THE LED BACKLIGHT oooi 23 SETUP MENUS inca cocinas 24 SETUP MENU OPERATION ccccccccecececeeeeseeeseseeees 24 PIC TUR E nie 25 AUDIO ee ratones 29 VIEW MODE ammut teers saustst salka Nt miss tenes 33 VIEW MODE VGA u ccccccccccccececsccceescecenscecetseeenneees 33 TV PROGR AM e Gone Nye S EV 35 SE TING Scraps ttu TIT TOSTA t r agate oottaa y n Sa 39 WALL MOUNT OPTION ccccccccececcecesececeeseeesereeenenees 50 WALL MOUNT INSTALLATION REMINDERS 50 TROUBLESHOOTING mesen eee 51 SPECIFICATIONS cccccccccccceceececesececersceceseceestneeersreeens 54 DIGITAL TELEVISION TRANSITION NOTICE DIGITAL TELEVISION TRANSITION NOTICE This device contains a digital television tuner so it should receive digital over the air TV programmi
3. Adjusting Video Presets 1 Use the 4 gt keys to select Video Presets and press C2 2 Press the 4 P keys on the remote control to select the desired option 3 Press E to save and exit the screen Sharpness Use Sharpness to adjust the sharpness or softness of the display Sharpness Adjusting Sharpness 1 Use the 4 P keys to select Sharpness and press C 2 Press the 4d keys on the remote control to adjust the sharpness level 3 Press E to save and exit the screen Color Temperature Use Color temperature to adjust the level of white balance in the display O Oe Color Temperature Three settings are available e Warm Pictures appear more reddish e Neutral Pictures appear more white e Cool Pictures appear with a bluish tint 27 SETUP MENUS Adjusting Color Temperature 1 Use the 4 P keys to select Color temperature and press C 2 Press the 4 gt keys on the remote control to select the desired option 3 Press E to save and exit the screen Hue Use Hue to adjust the balance of the red green and blue colors in the display Adjusting Hue 1 Use the 4 P keys to select Hue and press C2 2 Press the 4 P keys on the remote control to adjust the hue level 3 Press E to save and exit the screen Reset Select Yes on this sub menu to reset all display related settings N Reset NOTE The configuration settings for the Picture su
4. Y Westinghouse USER S MANUAL MANUEL DE L UTILISATEUR MANUAL DEL USUARIO LD 268 Series TABLE OF CONTENTS TABLE OF CONTENTS TABLE OP CONTENT Scsi dabas DIGITAL TELEVISION TRANSITION NOTICE 1 AVISO RELATIVO A LA TRANSICION A TELEVISION DISTA sete Sears ket a Pakana ASPEKTI ATS 1 IMPORTANT INFORMATION eee cece cece eee eee eee eeeeees 2 NV ATTI G Sins tall ett EE SSE E STK ev te lieth olla 2 NOTICE E Set loc dis 3 FCC COMPLIANCE STATEMENT setas daa 4 IMPORTANT SAFETY INSTRUCTIONS 000 000 5 Crou OVEeTIOSA isiin Tasan dida 6 Power Cord Protection iiilssisiusin asa knn ln ka ansa aa a ke 6 Ventilator enerne O test e 6 Safety Lamp DISposalii ainia ala 6 WARNINGS AND PRECAUTIONS oaaae 7 ANTENNA INSTALLATION SAFETY 0 00 0002 8 LIONI O enoaan a iene E AN 8 POW CE NIMC Soria all li Na 8 CLEANING THE LED TV ueno acond testit 9 DolDy DIgital NO NC Oates a 9 SRS Trademark Information cece onnaa nanna 9 PACKAGE CONTENTS cutres DN 02522 10 CONTROL PANEL mussa avaus A seo Ea 11 TERMINALS qt rd o kosta k d o vu sk vesi 12 REMOTE CONTROL osstiaata tant et iteki unk 13 REMOTE CONTROL OPERATION 0 eceeeeeeeee 14 INSTALLING THE REMOTE CONTROL BATTERIES 14 REMOTE CONTROL TRANSMISSION RANGE 14 LED TV BASE roo ANO 15 INSTALLING THE LED TV BASE 000 0 0005 15 REMOVING THE LED TV BASE
5. a Decrease the video resolution setting on the VGA cable is computer and try again connected Adjust the display settings Picture is cut off or appear in a sidebar Press to adjust the Aspect ratio screen Check your antenna connection If necessary rotate the antenna and wait up to ten seconds for a signal Reduce signal splitters and excessively long l cables Poor image quality in TV mode cutoff Replace poor antenna cables and or picture snowy connectors to improve signal quality images Press 3 to adjust the Aspect ratio Adjust the Noise Reduction setting in Picture menu In HDMI mode make sure the external device is compatible with the LED TV If any colors red green or blue are missing check the video cable to make sure it is securely connected Loose or broken pins in the cable connector could cause an improper Wrong abnormal or connection missing colors Adjust the Hue Saturation and Color Temperature settings in Picture menu Connect the TV to another computer and check if the problem is with the computer screen 52 TROUBLESHOOTING Corrective Action Make sure the audio input cable is properly connected to the correct terminal and that the correct input mode is enabled The volume may be muted press or Vol key to turn on the volume Adjust the Bass Treble and Balance settings No sound in Audio menu If you are using the TV speakers make sure the TV
6. box or game system 9 USB Service port For service only 12 REMOTE CONTROL REMOTE CONTROL Mutes the sound Press again to toggle 1 Mute DE the sound back on 2 Power Toggles the TV power on or off 3 Backlight Adjusts the LED screen backlight A MTS Toggles the Multichannel Television Sound options Toggles the closed caption display on or 5 CC Off 6 Sleep 22z Sets the sleep timer for the LED TV to P turn off automatically 7 Channel keys Use to key in the channel number Switches to the favorite channels for 8 Favorite details on how to save a new favorite channel see page 23 9 Enter ENT Executes a channel entry 10 Menu E Accesses the LED TV setup menus 11 Return Y Switches to the last selected channel 12 Arrow keys Navigate through the on screen menus 13 Enter CH Displays the Electronic Program Guide EPG It contains the program 14 GO information for the channel you re watching Displays the input source or channel 15 Info 4 information as well as the system date and time 16 Input Selects the video input source 17 Vol Ajusts the system volume 18 Ch A V Switches to other TV channels 19 Aspect ratio gt Selects the video display format Selects VGA Component as the input Selects TV or HDTV as the input 22 HDMI1 Selects HDMI1 as the input source Selects the Composite AV device as the 24 YPEP2 25 PC 26 HDMIZ 27 Video REMOTE C
7. press C 4 Use the Channel keys to enter the new password again for confirmation and press C 5 Press E to save and exit the screen 46 SETUP MENUS OSD Timeout Use OSD Timeout to adjust the OSD duration on the screen 10 sec 20 sec or 30 sec OSD Timeout Adjusting OSD Timeout 1 Use the 4 P keys to select OSD Timeout and press C2 2 Press the 4 gt keys on the remote control to select 10 sec 20 sec or 30 sec 3 Press E to save and exit the screen OSD Language Use OSD Language to select the language to display on the screen English French or Spanish OSD Language Adjusting OSD Lanquage 1 Use the 4 P keys to select OSD Language and press C3 2 Press the 4 P keys on the remote control to select English French or Spanish 3 Press E to save and exit the screen 47 SETUP MENUS Power Settings Use this sub menu to configure power related settings for the LED TV Power Settings VGA port DPMS Backlight Dark Room Dynamic Contrast AV lt Select Enter Confirm The following options are available e VGA port DPMS Use this setting to enable or disable VGA port OPMS e Backlight Use this setting to select the backlight mode Bright Room Medium Room or Dark Room e Dynamic Contrast Use this setting to enable or disable Dynamic Contrast Adjusting Power Settings 1 Use the 4 gt keys to select Power Settings and pres
8. the LED TV Turning off the power Press on the control panel or on the remote control to turn off the LED TV The LED behavior will depend on the enabled Power settings Turns from none to red Turn the power on Turns from red to none Turn the power off If you are not going to use the TV for a long time be sure to disconnect the power cord from the wall outlet and remove the batteries from the remote control In standby mode a small amount of electricity is still consumed even when the power is turned off ADJUSTING THE VOLUME Volume Press Vol to increase the volume press Vol to decrease the volume Mute Press MX to turn off the sound The mute icon appears on the screen Press again to turn on the sound 21 BASIC OPERATIONS CHANGING CHANNELS Follow the instructions below to change channels Using the Ch A Buttons Browse channels To browse through the available channels press Ch A V on the remote control or on the control panel Using the Channel Keys Selecting channel To change to a certain channel key in the channel number using the channel keys and press ENT Selecting digital channel To select a digital channel key in the digital channel number using the channel keys and the key then press ENT Using the Favorite Keys Selecting favorite channels To select a favorite channel press the
9. the screen e MPAA Rating Use this sub menu to select the ratings of allowable movies MPAA MPAA Rating E Enter Confirm Menu Exit May contain some scenes of drug use use of one of the harsher sexually derived words may be heard May be inappropriate for May contain explicit sex scenes an accumulation of sexually oriented language and or scenes of excessive violence Suitable for adult audiences only Rating does not signify that the film is obscene or pornographic X Contains extreme violence or explicit sex suitable for adult audiences only SETUP MENUS Adjusting MPAA Rating 1 Use the 4 P keys to select MPAA Rating and press Ce 2 Use the A W 4 keys to select the desired rating and press Ce repeatedly to block or unblock 3 Press E to save and exit the screen e Canada English Use this sub menu to select the classification categories based on Canadian ratings of allowable TV programs and movies en C8 Canada English Rating Enter Confirm Menu Exit Rating Description E Exempt shows Suitable for viewing by children of all ages Not suitable for children under 8 years of age Suitable for general audiences Parental guidance advised Suitable for people 14 years of age or Suitable for people 18 years of age or Adjusting Canada English Rating 1 Use the 4d P keys to select Canada English Rating and press C 44 SETUP MENUS 2 Use the A V 4
10. to add channels manually Channel Add AV Select Enter Confirm Menu Exit Adding Channels Manually 1 Use the 4 gt keys to select Manual Search and press C The Channel Add screen appears 2 Use the Channel keys on the remote control to enter the channel number and select Enter Wait a few moment for the TV to search for the channel 3 When the channel is found you can select Add to add to channel 38 SETUP MENUS SETTINGS Use the Settings sub menus to configure the LED TV operational setup and view the current firmware version Press G on the remote control or MENU on the control panel to display the setup menu screen then select Settings to display the Settings sub menu The following options are available Date and Time Closed Captions Parental Control OSD Timeout OSD Language Power settings Reset All and Version Date and Time Use Date and Time to adjust the current date and time Date and Time Date Day of Week JAN 1 2009 Thursday Time Zone Current Time Easter UTC KN Adjust for Daylight Saving Time 0 Auto Calibration av lt gt Select Enter Confirm Menu Exit Adjusting Auto Calibration 1 Use the 4 gt keys to select Date and Time and press C 2 Press C repeatedly to check enable or uncheck disable Auto Calibration 3 Press Q to save and exit the screen e Enable this option to view the system s current time e Both Date and Curren
11. C Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the distance between the LED TV and the receiver e Connect the LED TV to an outlet on a circuit separate from to which the receiver is connected e Ifthe interference persists even after performing the above measures consult the Westinghouse Service Center or an experienced radio TV technician for assistance FCC Warning To assure continued FCC compliance use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores If a BNC cable is used use only a shielded BNC 5 cable Also any unauthorized changes or modifications not expressly approved by the manufacturer will void the user s authority to operate this device IMPORTANT INFORMATION IMPORTANT SAFETY INSTRUCTIONS Make sure
12. Favorite button A B C or D corresponding to the preferred channel Saving a channel as a favorite 1 Switch to the channel you want to add as a favorite 2 Press and hold the Favorite button which you want to add the current channel to for 3 seconds 3 The Channel Saved message appears to confirm the new favorite channel item SELECTING THE INPUT SOURCE There are two ways to select the video input source Using the Individual Input Keys TV PC Video YPbPr HDMI Keys Press any of the following remote control keys to change the input source TV PC Video1 Video 2 YPbPr1 YPbPr2 HDMI1 or HDMI2 BASIC OPERATIONS Using the Input Key Select source using Input Key 1 Press Input 2 A list of supported video sources is displayed 3 Press h to select the preferred source 4 Press C to switch to the selected input source ADJUSTING THE DISPLAY FORMAT The input source can sometimes affect the way images are displayed on screen You can adjust the display format to view the image properly Format Options Press 3 repeatedly to toggle the display format As you toggle each option on the actual display will change accordingly The available options are e Standard Picture is displayed in its original size e Fill Picture is displayed to cover the entire screen e Overscan Picture is scaled down to fit the display area e 1 1 Mode Matches the incoming resolution exactly to the pixels
13. ONTROL OPERATION REMOTE CONTROL OPERATION INSTALLING THE REMOTE CONTROL BATTERIES CAUTIONS Only use AAA batteries Do not mix new and old batteries This may result in cracking or leakage which may pose a fire risk or lead to personal injury Insert batteries according to the and markings Inserting the batteries incorrectly may result in cracking or leakage which may pose a risk of fire or lead to physical injury Dispose of used batteries in accordance with local laws and regulations Keep batteries away from children and pets When the remote control will not to be used for an extended period remove the batteries 1 Remove the battery cover 2 Insert the batteries Make sure the and marks on the batteries match those inside the compartment 3 Re attach the battery cover REMOTE CONTROL TRANSMISSION RANGE Transmission range depends upon the reception angle The range of coverage is 20 horizontal vertical at a distance of 10 feet from the LED TV LED TV BASE LED TV BASE CAUTION The LED TV unit may be too heavy for one person to lift If this is the case make sure to ask for assistance in handling the LED TV to prevent physical injury and or damage to the unit INSTALLING THE LED TV BASE Open the LED TV carton box Remove the LED TV base Remove the plastic bag Remove the two top carton stabilizers from the LED TV Remove the
14. Speakers option is set to On in Audio menu If you are using an external audio device press and select Audio to make sure the TV Speakers option is set to Off in Audio menu NOTES If the problem condition persists even after performing the recommended corrective actions contact us by e Logging on to www wde com e Contacting the Westinghouse Customer Service at 800 701 0680 or e mail us at service wde com 53 SPECIFICATIONS SPECIFICATIONS tem Specification LD 268 Series 576 mm H x 324 mm V 1920 H x 1080 V T 1 4 ms Response Time LU 3 6 ms Aspect Ratio 1 77 16 9 Display color 16 7M e HDMI x2 AV with R L Audio x1 Audio Video VGA with 3 5 mm mini jack x1 Input Output SPDIF Out x1 Terminals USB for service x1 Tuner x1 R L Audio Line Out X1 Speaker Out SW 2 channels AV Timing 480i p 720p 1080i p 640 x 480 60Hz 75Hz 800 x 600 60Hz 75Hz PC Timing 1024 x 768 60Hz 75Hz 1280 x 1024 60Hz 1920 x 1080 60Hz Power Consumption Watts SSI Power Consumption Standby Watts TI SPECIFICATIONS With stand 657 x 472 x 179 mm Dimensions 25 86 x 18 58 x 7 05 inch Physical WxHxD Without stand 657 x 438 x 39 5 mm Specifications 25 86 x 17 24 x 1 56 inch Weight Net 4 6 kg Weight Gross 6 55 kg NOTES e These product specifications are subject to change without user notification e Do not set your computer graphics card to exceed the unit s refresh r
15. Use the A W keys to select the desired channel and press C to open the Edit Name screen Use the A V 4 gt keys to move the cursor to the desired symbol and press the C button to enter e Select Shift to toggle different symbol tables uppercase and lowercase letters numerals and special symbols e Select Back to backspace e Select Clear to delete all typed text Select Accept when finished Repeat steps 2 3 and 4 to add more channels Press E to save and exit the screen 36 SETUP MENUS MTS Use MTS to select multichannel television sound The following options are available e Mono Allows mono output useful when stereo is noisy or inconsistent e Stereo Allows stereo sound for superior TV viewing experience e SAP Allows second audio program from the speakers while watching a scene in the original program Adjusting MTS 1 Use the P keys to select MTS and press C 2 Press the 4 P keys on the remote control to select the desired option 3 Press E to save and exit the screen Auto Search Select Auto Search and press C2 Two options are available e Cable Choose this setting if you are receiving TV channels with a CATV cable TV e AIR Choose this setting if you are receiving TV channels with an antenna over the air Auto Search automatically creates a list of receivable channels for the selected source 37 SETUP MENUS Manual Add Use Manual Add
16. V Speaker 1 Use the 4 P keys to select TV Speaker and press C 2 Press the 4 gt keys on the remote control to select ON or OFF 3 Press E to save and exit the screen 30 SETUP MENUS Audio Preset Use this sub menu to select one of four preset audio options optimized for different sounding conditions Audio Presets The following options are available Rock Sets the equalizer to the Rock mode Pop Sets the equalizer to the Pop mode Classical Sets the equalizer to the Classical mode Flat Sets the equalizer to the Flat mode Custom Uses the customized settings Adjusting Audio Preset 1 Use the 4 P keys to select Audio Preset and press C2 2 Press the 4 b keys on the remote control to select the desired option 3 Press E to save and exit the screen TruSurround HD Use this sub menu to toggle the TruSurround HD on and off TruSurround HD 31 SETUP MENUS Adjusting TruSurround HD 1 Use the 4 P keys to select TruSurround HD and press C 2 Press the 4 gt keys on the remote control to select On or OFF 3 Press E to save and exit the screen Reset Select Yes on this sub menu to reset all audio related settings 32 SETUP MENUS VIEW MODE Use the View Mode sub menu to select the aspect ratio of the display Press 8 on the remote control or MENU on the control panel to display the setup menu screen then select View Mode to dis
17. an be set to ON or OFF e Analog Type Can be set to CC1 CC2 CC3 CC4 T1 T2 T3 or T4 e Digital Type Can be set to CS1 CS2 CS3 CS4 CS5 or CS6 40 SETUP MENUS e Font Can be set to As Broadcaster Style 1 Style 2 Style 3 Style 4 Style 5 Style 6 or Style 7 e Size Can be set to As Broadcaster Small Medium or Large e Font Color Can be set to As Broadcaster Black White Green Blue Red Cyan Yellow or Magenta e Background Color Can be set to As Broadcaster Black White Green Blue Red Cyan Yellow or Magenta e Edge Type Can be set to As Broadcaster None Raised Depressed Uniform Shadow Left or Shadow Right e Edge Color Can be set to As Broadcaster Black White Green Blue Red Cyan Yellow or Magenta e Foreground Opacity Can be set to As Broadcaster Solid Translucent Transparent or Flashing e Background Opacity Can be set to As Broadcaster Solid Translucent Transparent or Flashing Adjusting Closed Captions Settings 1 Use the 4 P keys to select Closed Captions and press C 2 Use the A V keys to select the desired Closed Captions option 3 Use the q gt keys to adjust the value 4 Press amp to save and exit the screen Parental Control Use Parental Control to block channels and change the password You must enter a six digit password to use the Parental Control The factory password is 999999 Enter Password 079 Key in password Enter Co
18. ates doing so may cause damage to the LED TV 55
19. b menus will only be applied to the current input source 28 SETUP MENUS AUDIO Use the Audio sub menus to configure the audio quality These settings apply to the LED TV speakers only Any connected audio devices are not affected Press El on the remote control or MENU on the control panel to display the setup menu screen then select Audio to display the Audio sub menu The following options are available Bass Treble Balance TV Speaker Audio Presets and Reset Bass Use Bass to calibrate low pitched sounds Adjusting Bass 1 Use the 4 P keys to select Bass and press C 2 Press the 4 P keys on the remote control to adjust the bass level 3 Press E to save and exit the screen Treble Use Treble to calibrate high pitched sounds Treble Adjusting Treble 1 Use the 4 P keys to select Treble and press C 2 Press the 4 P keys on the remote control to adjust the treble level 3 Press E to save and exit the screen 29 SETUP MENUS Balance Use Balance to adjust the sound balance between the L R speakers yo Balance Adjusting Balance 1 Use the q P keys to select Balance and press C 2 Press the 4 keys on the remote control to adjust the balance level 3 Press E to save and exit the screen TV Speaker Use this sub menu to toggle the LED TV speakers on and off ey o TV Speaker maroon Adjusting T
20. culas pregrabadas o para utilizar sus videojuegos Para obtener m s informaci n llame FCC 1 888 CALL FCC 1 888 225 5322 o refi rase a www DTV gov Para toda informaci n sobre el programa de conversores de TV y acerca de los cupones del gobierno que se pueden usar para comprarlos refi rase a www dtv2009 gov o llame al NTIA al 1 888 DTV 2009 IMPORTANT INFORMATION IMPORTANT INFORMATION Warnings To reduce the risk of fire or electric shock e Do not expose this product to rain or moisture e Do not remove the rear cover There are no user serviceable parts inside Refer all servicing requirements to qualified service personnel e The plug should be connected to a mains socket outlet with a protective earthing connection The lightning flash with arrowhead inside an equilateral triangle symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation inside an equilateral triangle symbol is intended to alert the user to related operating and maintenance instructions in the user documentation accompanying the product WARNING This device must be operated with the original power supply CAUTION The power supply outlet should be located near the LED TV and should be easily accessible Always use the appropriate AC cord that is certified for your specific coun
21. d Separate VHF UHF Antenna VHF Antenna UHF Antenna Home Antenna terminal 75 ohm 300 ohm twin lead COMBINER Not supplied 300 ohm twin lead 75 ohm coaxial ee NOTE The F type connector should be finger tightened only When connecting the RF cable to the LED TV do not tighten F type connector with any tool If tools are used it may cause damage to the LED TV e g breaking of internal circuit CABLE TV CTV DTV CONNECTION The unit has a TV tuner 75 ohm coaxial cable connector located on the rear I O panel for easy cable hookup When connecting the 75 ohm coaxial cable to the unit screw the 75 ohm cable to the TV tuner Some cable TV companies offer premium pay channels Since the signals of these channels are scrambled a cable TV converter descrambler is usually provided to the subscriber by the cable TV company This converter descrambler is necessary for normal viewing of the scrambled channels Set your TV to channel 3 or 4 Typically one of these channels is used If a channel is unknown consult your cable TV company For more specific instructions on installing cable TV consult your cable TV company One possible method of utilizing the converter descrambler provided by your cable TV company is explained below 17 EXTERNAL DEVICE CONNECTIONS e A position on the RF switch not supplied You can view all unscrambled channels by using
22. electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal IMPORTANT INFORMATION CLEANING THE LED TV Make sure the LED TV is turned off and the power cord is disconnected from the power outlet Never spray or pour any liquid directly onto the screen or the case To clean the screen 1 Wipe the screen with a clean soft lint free cloth This removes dust and other particles 2 lf itis still not clean apply a small amount of non ammonia non alcohol based glass cleaner onto a clean soft lint free cloth and wipe the screen To clean the case 1 Wipe the case with a soft dry cloth 2 lf itis still not clean apply a small amount of non ammonia non alcohol based mild non abrasive detergent onto a clean soft lint free cloth then wipe the surface Dolby Digital Notice DO DoLBY DIGITAL Manufactured under license from Dolby Laboratories Dolby and the double D symbol are registered trademarks of Dolby Laboratories SRS Trademark Information e TruSurround HD SRS and the O symbol are trademarks of SRS Labs Inc e TruSurround HD technology is incorporated under license from SRS Labs Inc SRS TruSurround HD creates a truly immersive surround sound experience with rich bass and clear dialog fro
23. ercury and must be recycled or disposed of according to local state or federal laws For more information contact the electronic industries alliance at www eiae org IMPORTANT INFORMATION WARNINGS AND PRECAUTIONS e Do not orient the LED TV towards direct sunlight to reduce glare e Ifthe LED TV will not be used for a long period of time unplug the unit and remove the batteries from the remote control e Avoid touching the display screen by hand or any object e Never remove the rear cover The LED TV interior contains high voltage parts You may be seriously injured if you touch them e Always handle the LED TV with caution when moving it e Do not install the LED TV in airtight compartments or in areas where it can be exposed to water or high temperature e Ensure that the area around the LED TV is clean and free of moisture e Do not place anything on the LED TV that can hinder heat dissipation e Do not place naked flame sources such as lighted candles on or near the LED TV e Do not place anything on the LED TV that can cause liquid to splash on it e g flower vase e Do not place heavy objects on the LED TV audio video cables or power cord e Ifthe LED TV emits smoke abnormal noise or a strange odor immediately turn it off and contact the Westinghouse Service Center by Logging on to www wde com Contacting the Westinghouse Customer Service at 800 701 0680 E mailing us at service wde com
24. keys to select the desired rating and press Ce repeatedly to block or unblock 3 Press E to save and exit the screen Canada French Use this sub menu to select the ratings of allowable TV programs and movies These ratings are based on the classification categories determined by La R gie du cin ma du Qu bec fr 8 Canada French Rating EM G 8 ans 13 ans 16 ans 18 ans Enter Confirm Menu Exit Rating Description E Exempt shows For general audiences l years of age l years of age l years of age M Not suitable for persons under 18 years of age Adjusting Canada French Rating 1 Use the 4 P keys to select Canada French Rating and press C2 2 Use the A V 4 keys to select the desired rating and press C repeatedly to block or unblock 3 Press E to save and exit the screen 45 SETUP MENUS e Channel Block Channel Block allows you to block channels Channel Block Adjusting Channel Block 1 Use the 4 P keys to select Channel Block and press C amp 2 Use the A W keys to select the desired channel and press C repeatedly to block or unblock 3 Press El to save and exit the screen e Change Password Change Password allows you to change your current password Changing Password 1 Use the 4d P keys to select Change Password and press C 2 Use the Channel keys to enter the current password and press C 3 Use the Channel keys to enter the new password and
25. lly serious injury 50 TROUBLESHOOTING TROUBLESHOOTING Corrective Action Make sure the power indicator is illuminated blue Make sure the power cord is securely connected to the AC in jack and is plugged into a functional AC outlet You may want to plug in another electrical device to the power outlet to verify that it is supplying the proper voltage AI U Make sure the sleep timer is turned off turned off Forgotten PIN Use Reset All in Settings menu to reset your password Press only one button at a time No power Remote control Make sure the batteries are properly inserted does not work The batteries may already be drained out Replace batteries with new ones Remote control Purchase a separate learning remote control code cannot be Go to www wde com for a list of remote detected by a codes universal remote Make sure the video input cable is properly connected to the correct terminal and that the correct input mode is enabled To illustrate when a VGA cable is connected to display a computer screen the PC input mode must be No picture enabled Verify that the antenna is properly connected and that the preferred channel is enabled in the channel list Press and select Channels Channel List Adjust the display settings TROUBLESHOOTING Corrective Action No picture or the No Make sure the VGA cable is properly Signal message connected to the LED TV s VGA port appears when
26. m only two speakers S SsO TruSurround HD PACKAGE CONTENTS PACKAGE CONTENTS 26 LED TV Unit Remote Control with 2x AAA batteries M4x18 4pcs M5x16 1pc E Cover neck 10 CONTROL PANEL CONTROL PANEL uh oo a A Description 1 MENU MEME Di pia the LED TV setup screen Volume i e Adjusts the volume during playback e Selects an item on a menu screen 3 Channel e Switches the channel during TV viewing e Selects an item on a menu screen 4 INPUT e Selects the video input source e Executes a command on a menu screen Toggles the power on and off 11 TERMINALS TERMINALS SPDIF HDMI 1 JE HDMI 2 K I USB 9 VGA E 4 DC in Connects the AC adapter from this outlet to a i power source Connects the LED TV to an antenna or cable i Connect to an external AV device such as a VCR 3 Composite AV input DVD player set top box or game system Connects to the audio out port of a computer 5 VGA Connects to a computer or other device with a l VGA output using a 15 pin VGA cable 6 Audio out Connect to an audio output device 7 SPDIF audio out Connects to an external digital audio receiver 8 HDMI 1 2 Connects to an external AV device such as a l VCR DVD player set top
27. n of the display Emmin V Position Fine Tune Use this sub menu to fine tune the display Emman Fine Tune Auto Sync Use this sub menu to synchronize the display automatically E EM Auto Sync 34 SETUP MENUS TV PROGRAM Use the TV Program sub menus to manage the channel list language sound and to scan for available TV channels in your area Press E on the remote control or MENU on the control panel to display the setup menu screen then select TV Program to display the TV Program sub menu The following options are available Skip List Channel Edit MTS Auto Search and Manual Add Skip List Use Skip List to select the channels you want to skip Channel Skip List Clear List AV Select Enter Confirm Menu Exit Adding Channels to Skip List 1 Use the 4 P keys to select Skip List and press C The Channel Skip List screen appears 2 Use the A V keys to select the desired channel 3 Press C repeatedly to check add to the Skip list or uncheck clear to the Skip list the channels 4 Repeat steps 2 and 3 to add more channels 5 Press E to save and exit the screen 35 SETUP MENUS Channel Edit Use Channel Edit to assign a name to a channel Channel Name Edit AV Select Enter Confirm Menu Exit Editing Channel Names 1 Use the 4d P keys to select Channel Edit and press C The Channel Name Edit screen appears
28. nections Antenna Cable system PC Audio amplifier AUDIO OUT AUDIO OUT rt Ham gt Audio gt 8 SPDIF cable SPDIF cable HDMI 1 rom EDO R AUDIO IN VGA LDR I vii Cable TV line jack cable m 3 5 mm RGB Antenna cable stereo mini cable Composite AV cable DVD player with an HDMI terminal Home video HDMI HDMI cable game system m n m 240 DVI HDMI cable Power outlet DVD player Digital TV tuner DVD player with a DVI terminal 19 POWER CONNECTION POWER CONNECTION CONNECTING AC POWER IMPORTANT The LED TV is designed to be powered via an AC adapter Use ONLY the AC adapter included in the package Turn off all connected devices before plugging the AC adapter into the power outlet Connect the power cord of the AC adapter to the LED TV then to a proper AC outlet VIA INITIAL SETUP Press l on the control panel or on the remote control to turn on the LED TV Select the desired language and select Yes to use the SetupWizard The SetupWizard will guide you on how to set up the LED TV s operational settings BASIC OPERATIONS BASIC OPERATIONS TURNING THE POWER ON AND OFF Turning on the power Press l on the control panel or on the remote control to turn on
29. nfirm Menu Exit After you enter the correct password the Parental Control menu is shown By default only the Rating and Change Password submenu are displayed To display the hidden submenu set Rating to ON 41 SETUP MENUS The following options are available e Rating Select ON OFF to hide or display the hidden submenu e Block Unrated Select ON OFF to block unlock all unrated programs Adjusting Rating and Block Unrated 1 Use the 4 gt keys to select Rating or Block Unrated and press Ga 2 Use the 4d P keys to select ON or OFF 3 Press E to save and exit the screen e TV Rating Use this sub menu to customize US TV Rating programs TV Y TV Rating 4 Automatic Blocking Rating Description TV Y Suitable for young children TV Y7 May not be suitable for children under 7 TV G Suitable for all audiences TV PG Parental guidance suggested Parental guidance suggested for children under 14 TV MA Suitable for mature audiences only may be unsuitable for children under 17 FV Fantasy violence combative situations TV 14 Suggestive dialogue L Coarse language Sexual situations Violence SETUP MENUS Adjusting TV Rating 1 Use the 4 P keys to select TV Rating and press C 2 Use the A V 4 keys to select the desired rating and press C repeatedly to block or unblock You can also select Lock All to block all or Unlock All to unblock all 3 Press E to save and exit
30. ng with a suitable antenna after the end of full power analog TV broadcasting in the United States on June 12 2009 The nationwide switch to digital television broadcasting will be complete on June 12 2009 but your local television stations may switch sooner After the switch analog only television sets that receive TV programming through an antenna will need a converter box to continue to receive over the air TV Watch your local stations to find out when they will turn off their analog signal and switch to digital only broadcasting For more information call the FCC at 1 888 CALL FCC 1 888 225 5322 or see www DTV gov For information on the TV Converter program and on government coupons that may be used toward the purchase of one see www dtv2009 gov or call the NTIA at 1 888 DTV 2009 AVISO RELATIVO A LA TRANSICION A TELEVISION DIGITAL Este equipo incorpora un sintonizador de television digital lo que le permitira recibir una programaci n digital televisada por aire con una antena adecuada cuando se terminar la transmisi n de alta potencia de la televisi n anal gica en los Estados Unidos el 12 de Junio de 2009 Ciertos receptores de televisi n antiguos si dependen de una antena de TV necesitar n un conversor de TV para recibir por el aire una programaci n digital pero seguir n funcionando como antes para otros usos por ejemplo para ver emisoras de TV de baja potencia que todav a transmiten en anal gico para ver pel
31. ng to gualified service personnel Servicing is reguired when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped IMPORTANT INFORMATION Circuit Overload Do not overload wall outlets extension cords or power strips This can result in a fire or electronic shock Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Periodically inspect the cords for damage Install the LED TV near a wall socket outlet where the power cord can be readily accessed Ventilation The slots and openings on the cabinet are provided for necessary ventilation To ensure reliable operation of the LED TV and to protect it from overheating these slots and openings must never be blocked or covered Never cover the slots and openings with a cloth or other materials Do not block the openings by placing the LED TV on a bed sofa rug or other similar surface Do not place the LED TV in a built in installation such as a bookcase or a rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Safety Lamp Disposal Lamp s inside this product contain m
32. play the View Mode sub menu The following options are available Standard Fill Overscan and 1 1 Mode WE View Mode Standard Picture is displayed in its original size Fill Picture is displayed to cover the entire screen Overscan Picture is scaled down to fit the display area 1 1 Mode Matches the incoming resolution exactly to the pixels without any scaling Adjusting View Mode 1 Press the 4 b keys on the remote control to select the desired option 2 Press E or C to save and exit the screen VIEW MODE VGA Select VGA as your input source and use the View Mode sub menu to adjust the display in VGA mode Press 8 on the remote control or MENU on the control panel to display the setup menu screen then select View Mode to display the View Mode sub menu The following options are available Aspect Ratio H Position V Position Fine Tune and Auto Sync Aspect Ratio Use this sub menu to select the display s aspect ratio in the following options 33 SETUP MENUS e 1 1 Mode Matches the incoming resolution exactly to the pixels without any scaling e Standard Picture is displayed in its original size e Fill Picture is displayed to cover the entire screen Aspect Ratio ii A H Position Use this sub menu to adjust the horizontal position of the display E Ekaa H Position V Position Use this sub menu to adjust the vertical positio
33. protective plastic covering the LED TV Grasp the two sides of the LED TV and then pull it out of the carton box Remove the two bottom carton stabilizers from the LED TV Lay the LED TV on a clear flat and stable surface O AON Oo hb OQ No Align the base to the bottom side of the LED TV and use four M4 x 18 screws to secure it 10 Carefully orient the LED TV in an upright position 11 Use one M5 x 16 screw to fix the stand base and LED TV on the desk 15 LED TV BASE REMOVING THE LED TV BASE If you intend to repack the LED TV unit for shipping or storage or you want to change the installation to a wall mount option you must first remove the LED TV base 1 Turn off the LED TV and all connected devices 2 Disconnect the power cord from the LED TV 3 Disconnect all signal cables from the I O port terminals 4 Remove the M5 x 16 screw securing the base to the desk 5 Lay the LED TV on a clear flat and stable surface 6 Remove the screws securing the base to the LED TV 7 Detach the base from LED TV 8 Pack the screws you removed in step 5 together with the LED TV base for future reassembly 16 ANTENNA CONNECTION ANTENNA CONNECTION OUTDOOR ANTENNA CONNECTION Cable TV lead in VHF UHF or VHF UHF combination antenna 75 ohm coaxial cable round 300 75 ohm ADAPTER 300 ohm twin lead flat Not supplie
34. s C 2 Use the A V keys to select a desired option 3 Use the q P keys to adjust the value 4 Press E to save and exit the screen Reset All Select Yes on this sub menu to reset all LED TV operational settings Do this only if any of the following conditions occurs e The system fails to respond to the remote control ensure that the remote control batteries are still working and you are within the transmission range e The new configuration settings cause unexpected results e You forget the system PIN Reset All 48 SETUP MENUS Version Use this sub menu to view the LED TV s serial number and firmware version Version 49 WALL MOUNT OPTION WALL MOUNT OPTION The LED TV has been fitted with VESA FPMPMI compliant mounting holes These 200 x 100 mm mounting holes allow the unit to be mounted on a wall Use the four M4 x L10 mm screws to wall mount the LED TV gt gt SSS WALL MOUNT INSTALLATION REMINDERS e Remove the LED TV base first before mounting the unit on a wall e Itis the user s responsibility to use a UL listed wall mount unit rated to support the weight of this LED TV e Please consult qualified contractors for wall mount installation CAUTION The incomplete or improper mounting of this unit to a wall may cause it to fall down resulting to property damage and or potentia
35. t Time are unavailable for adjustments when Auto Calibration is enabled Adjusting Time Zone 1 Use the 4 gt keys to select Date and Time and press C3 2 Use the A W keys to select Time Zone and press Cs 3 Use the A W keys to select the desired Time Zone Samoa Hawaii Alaska Pacific Mountain Central Eastern Atlantic or Newfoundland 4 Press E to save and exit the screen 39 SETUP MENUS Adjusting Date and Time 1 Use the P keys to select Date and Time and press C 2 Use the A V keys to select Date or Current Time and press Ce 3 Use the 4 P keys to select a date or time segment 4 Use the A keys to adjust the value 5 Press 8 to save and exit the screen Adjusting Daylight Saving 1 Use the 4d P keys to select Date and Time and press C 2 Press C repeatedly to check enable or uncheck disable Adjust for Daylight Saving Time 3 Press E to save and exit the screen Closed Captions Use Closed Captions to configure the settings for closed captioning in TV programs Closed Captions Closed Captions ON Analog Type CC1 Digital Type CS1 Y YF Font As Broadcaster Size As Broadcaster Font Color As Broadcaster Background Color As Broadcaster Edge Type As Broadcaster Edge Color As Broadcaster Foreground Opacity As Broadcaster Background Opacity As Broadcaster YY se F VE YF AY 4h Select Menu Exit The following options are available e Closed Captions C
36. the TV s channel keys e B position on the RF switch not supplied You can view the scrambled channels via the converter descrambler by using the converter s channel keys RF switch not supplied Cable TV line Not supplied EXTERNAL DEVICE CONNECTIONS IMPORTANT Turn off the LED TV first before connecting an external device to prevent any possible damage or physical injury For more information about external device connections see the operation manual of the external device you wish to connect to the LED TV Make sure that the correct cables are connected to each terminal Improper cable connections may cause damage to the LED TV You can enjoy picture and sound by connecting various audio video devices to the terminals located on the rear and side I O panels of the LED TV e TV cable input You can use a commercially available audio video cable e Component YPbPr input Picture can be displayed only when a 480i 480P 720P or 1080i signal is received e HDMI input Picture can be displayed only when a 640 x 480 480P 720P or 1080i signal is received When you connect to the HDMI terminal with a DVI HDMI conversion cable there is a possibility that the picture may not display correctly e Audio output You can output audio signals from the LED TV set through the analog audio out and SPDIF terminals 18 EXTERNAL DEVICE CONNECTIONS The following diagram shows the external device con
37. to adjust the luminance level o mf ARA Brightness Adjusting Brightness 1 Use the q P keys to select Brightness and press C amp 2 Press the keys on the remote control to adjust the brightness level 3 Press E to save and exit the screen Contrast Use Contrast to adjust the brightness to darkness ratio Le Contrast Adjusting Contrast 1 Use the 4 P keys to select Contrast and press C 2 Press the keys on the remote control to adjust the contrast level 3 Press E to save and exit the screen 25 SETUP MENUS Saturation Use Saturation to adjust the color intensity Saturation Adjusting Saturation 1 Use the 4 gt keys to select Saturation and press C2 2 Press the 4d P keys on the remote control to adjust the saturation level 3 Press E to save and exit the screen Video Presets Use this sub menu to select one of four preset view options optimized for different viewing conditions The following options are available e Showroom Uses increased color and sharpness for a vibrant picture display e Movie Images are displayed as accurately near to its original recording condition e Game Uses increased brightness and response time level for enjoying video games e Sports Uses high contrast display for clear cut images ideal for viewing sports events e Custom Uses the customized settings 26 SETUP MENUS
38. to note and follow all warnings and instructions marked on the LED TV Observe the following safety instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over N W Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servici
39. try Some examples are listed below e USA UL e Canada CSA e Japan Electric Appliance Control Act IMPORTANT INFORMATION NOTICES Important Notices Concerning Power Cord Selection The specific power cord for this LED TV is enclosed and has been selected according to the country of destination Use the enclosed power cord to prevent electric shock Observe the following guidelines if it is necessary to replace the original cord set or if there is no cord set enclosed The female receptacle of the cord set must meet IEC 60320 requirements and should look like Figure A1 below Figure A1 For the United States and Canada In the United States and Canada the male plug is a NEMA5 15 style Figure A2 UL listed and CSA labeled For LED TVs that are to be placed on a desk or table type SVT or SJT cord sets may be used For LED TVs that are to be placed directly on the floor only SJT type cord sets may be used The cord set must be selected according to the current rating for the LED TV Consult the table below for the selection criteria of power cords used in the United States and Canada Cord Type Size of Conductor in Cord Maximum Unit Current Rating 18 AWG 10 Amps 16 AWG 12 Amps Figure A2 14 AWG 12 Amps 18 AWG 10 Amps IMPORTANT INFORMATION FCC COMPLIANCE STATEMENT This equipment has been tested and complies with the limits for a Class B digital device pursuant to part 15 of the FC
40. without any scaling ADJUSTING THE LED BACKLIGHT Different viewing conditions can affect the quality of the display You can adjust the LED backlight to suit the current viewing condition Backlight options Press repeatedly to toggle the Backlight mode The available options are Bright Room Medium Room and Dark Room 23 SETUP MENUS SETUP MENUS SETUP MENU OPERATION Use the setup menus to configure the various operational settings of the LED TV Displaying the setup menu screen Press E on the remote control or MENU on the control panel to display the setup menu screen Navigating the setup menu screen Use the buttons on the remote control or on the control panel to navigate through the menu screens Control Panel Select and display a primary menu Volume then l INPUT Adjust sub menu options Select and display a sub menu Channel then Select a sub menu or a sub INPUT menu option Returns to the primary menu tab from a sub menu screen SETUP MENUS PICTURE Use the Picture sub menus to configure the display quality Press El on the remote control or MENU on the control panel to display the setup menu screen then select Picture to display the Picture sub menu The following options are available Brightness Contrast Saturation Video Presets Sharpness Color temperature Hue and Reset Brightness Use Brightness
Download Pdf Manuals
Related Search