GEOPOINT LCD
Contents
1. s e 27 eum T GEOPOINTLCD Gok EON Peet sb OEM 4b TRACKER User Guide GEOPOINT LCD PERSONAL TRACKER User Guide July Edition 2009 Limitation of Liability The Manufacturer reserves the right to modify the devices or the device specifications in this manual without prior notice Any copy of this manual in part or in full whether by photocopy or by other means even of electronic nature without the manufacture giving written authorisation breaches the terms of copyright and is liable to prosecution It is absolutely forbidden to use the device for different uses other than those for which it has been devised for as inferred to in this manual When using the features in this device obey all laws and respect privacy and legitimate rights of others EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH SAID PRODUCT AND THE MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBLIGATION OR LIABILITY OTHER THAN SUCH AS IS EXPRESSLY SET FORTH HEREIN All trademarks in this manual are property of their respective owners The information contained in this manual is for information purposes only is subject to changes without previous notice and cannot be considered binding for the Manufacture2. ower Save Mo Alarm SMS Position Data Recording Update of the Tracker Firmware Version Technical Features Manufacturer s Limited Warranty Warranty Period Safety Instructions Safety Instructions Please read the following safety instructions carefully Not following them may be dangerous and or illegal For further details please read carefully the user manual complete version contained in the enclosed CD ROM Do not switch the device on when prohibited or whenever it could cause any interference or danger Obey all local laws Always keep your hands free to operate the vehicle while driving Your first consideration while driving should be road safety All wireless devices may be susceptible to interference which could affect the performance of other appliances radio Switch the device off in hospitals or near medical equipment hearing aid equipment pacemaker the device could cause interference Always keep a distance of 20 cm between pacemaker and device Wireless and digital devices can cause interference with aircraft equipment Donotusethe device at a refuelling point Switch off when near petrol stations or fuel depots and chemical plants The device could interfere with the correct functioning of the electronic equipment Do not use the device where blasting is in progress Do not use the device for any uses other than those it has been built for Keep to
3. 5 10 30 al Rate 0 OFF Mode OFF Erase OK Back 10 30 OK Use of the Tracker The setup of the position points recording can be carried out by means of the provided software or directly on the tracker Rate Set the temporal recording rate Available values 0 1 5 10 30 60 300 seconds By selecting 0 the recording at temporal rate is disabled Distance Set the distance in meters to cover Available values 0 10 50 100 500 1km By selecting 0 the recording for covered distance is disabled Mode Select the memory recording mode FILL after having finished all the available memory space stop recording the oldest data is kept RING after having finished all memory space the data already recorded is overwritten the latest data is kept OFF disable the recording Erase Delete all data contained in the memory The Erase function deletes all GPS data contained in the tracker memory Once deleted the A data is no longer retrievable A If the Power Save Mode with position SMS or cyclic GPRS has been enabled the tracker position will be recorded at each automatic switching ON The set Rate and Distance parameters will not be considered 27 Use of the Tracker SOS Key By pressing the SOS key for at least 2 seconds for 5 consecutive times every minute an SMS message is immediately sent to the preset phone numbers max of 4 phone numbers and a brief acousti
4. GSM network coverage The info message changes according to the function in use Connection via USB Activated keypad lock SMS sending receiving Connected headphones More symbols can be displayed LJ Data connection GPRS connection The item relevant to the key changes according to the function in use 10 Use of the Tracker Tracker Function Description Refer to GPS Info on Display the tracker displays the info relevant to its position chapter Use of the Tracker Phone the tracker displays the phonebook and a chapter Use of the Tracker call can be received or carried out SOS key the tracker sends an alarm message chapter Use of the Tracker Position Request the tracker sends an SMS containing its position to the phone number which requested this data o hapter Tracker Management by SMS Automatic Position Sending the tracker sends automatically its position by SMS or by GPRS connection o hapter Use of the Tracker section Setup hapter Tracker Management by SMS o Position Data Recording the tracker records its position data to review the track afterwords o apter Use of the Tracker section Setup apter Setup by MyTrack Software o Geofence the tracker sends an alarm SMS to the chapter Tracker Management by SMS preset phone number everytime it exits or ri enters in a preset rectangular area Anchor the tracker sends an
5. 0100 radius at 100 m containing both enabling and radius fields e g 1 0100 wanc 1 0100 NOTE to enable or disable the Anchor function Reply NO VALID CENTER POS without setting the radius send the wanc command m with the first field only In this case the default radius Description or the previously set radius is considered 1 enables 0100 radius at 100 m NO VALID CENTER POS if the center point cannot be detected Case C Command wanc 1 Reply wanc 1 OK Description T enables the function considering the default radius or the previously set radius wem Erase all position data recorded in the memory Command wem Reply wem OK 40 Tracker Management by SMS Command Meaning and Values Example wgprs Set the GPRS parameters and start the continuous Case A GPRS connection Command setup O set the GPRS parameters without starting wgprs 0 213 86 89 11 9500 the connection Reply 1 connect with the new parameters IP PORT wgprs 0 213 86 89 11 9500 OK 2 connect with the parameters previously preset Description parameters IP host IP address PORT TCP port NOTE the IP and PORT parameters should be written between commas NOTE if there is no GPRS connection the tracker sends an error SMS containing GPRS ERROR O set GPRS parameters without starting the connection 213 86 89 11 host IP address example 9500 TCP port
6. Case B Command wgprs 1 213 86 89 11 9500 Reply wgprsz1 213 86 89 11 9500 Description 1 GPRS connection with new parameters 213 86 89 11 host IP address example 9500 TCP port Case C Command wgprs 2 Reply wgprs 2 OK Case D Reply NO GPRS COVERAGE Description NO GPRS COVERAGE if GPRS signal is missing 41 Setup by MyTrack Software Setup by MyTrack Software GEOPOINT INCREASE THE PRINT Setup Pan PLay RECORDING SPEED RECORDING SPEED SETUP CONNECT MyTrack DER INFORMATION BAR TO SCROLL THE RECORDING ADDRESS Book DISCONNECT CENTER Pause FORWARD DECREASE THE RECORDING SPEED OPEN Pace SETUP Power Save Mode The Power Save Mode allows for optimal management of the battery tracker It is possible to set the tracker automatic switching on off according to specific use requirements There are three Power Save Modes programmable by means of the provided software except for Cyclic Position SMS which is programmable by SMS command too After Power Save Mode enabling the tracker will switch off automatically 2 minutes after tracker disconnection by the provided software WITH MOTION MOTION OFF OFF NO MOTION FOR A PRESET TIME NO DATA EXCHANGE 42 Setup by MyTrack Software WITH CYCLIC POSITION SMS OFF ON OFF CYCLIC POSITION SMS SENDING Bek SMS SENT A Before using this mode enable and set the Cy
7. rO rO 10 30 Menu 10 30 Yes 10 30 No 12 Use of the Tracker Menu Structure To access the main menu press Menu in the Home page The first section GPS will be displayed Scroll down the sections turning the JOG and press OK to enter into the desired item To exit the main menu and display the Home page press Home The Speed function is not available in case of tracker compatible for OnTrack application mul EH EH GPS ANCHOR GUIDE SETUP v v M v Home 10 30 OK Home 10 30 OK Home 10 30 OK Home 10 30 OK EN FINDER SPEED v v v Home 10 30 OK Home 10 30 OK Home 10 30 OK 4 13 Use of the Tracker GPS The data received by the GPS system are shown on the display NEC A Lat 45 45 67N A Spd 20km h A G PS Long 08212 34 Dir 270 Alt 256 m Sat 8 3D FIX v M v Home 10 30 2 Back 10 30 Back 10 30 Phone The tracker also works as a GSM telephone The call functions are extremely simple The phone numbers and names are pre programmed in the phone book by means of the provided software 14 PHONE BOOK 10 NUMBERS U
8. 49 Manufacturer s Limited Warranty Manufacturer s Limited Warranty This warranty does not limit the user s statutory rights under applicable national laws relating to the sale of consumer products During the warranty period the Manufacturer or Manufacturer authorized service company will in a commercially reasonable time remedy defects in materials design and workmanship free of charge by repairing The Manufacturer will in accordance with this Limited Warranty unless otherwise required by law remedy defects by repair or should the Manufacturer in its discretion deem it necessary replace the Product This Limited Warranty is only valid and enforceable in the country where the user has purchased the Product provided that the same Product has been intended for sale in that country by the Manufacturer However if the user has purchased the Product in a member state of the European Union Iceland Norway Switzerland or Turkey and such Product was originally intended by the Manufacturer for sale in one of these countries this Limited Warranty is valid and enforceable in all of these above listed countries Some limitations to the warranty service may apply because of country specific elements in the Products Warranty Period The warranty period starts at the time of Product s original purchase by the first end user The Product may consist of several different parts and different parts may be covered by a different warranty p
9. A SETUP Memory v v Home 10 30 OK Back 10 30 Ok Back 10 30 OK mH NER Tracking OFF Tracking OFF Tracking OFF GPRS rate OFF GPRS rate OFF GPRS rate Back 10 30 10 30 OK 10 30 OK Available values OFF 1m 5m 10m 15m 30m 1h 2h 4h 8h 12h 18h 24h mil EN Tracking OFF GPRS rate im Back 10 30 OK El Before rate selection check if the GPRS parameters have been set properly 23 Use of the Tracker TONES SETUP EN EH Hie 24 Main Memory Back 10 30 A v OK EH Ring Call HIGH Keys OFF 505 ON Back 10 30 OK A A SETUP es Memory V v Home 10 30 OK Back 10 30 OK I Ring il Ring Call HIGH Call HIGH Keys OFF Keys OFF 505 ON 505 ON Back 10 30 OK Back 10 30 OK at NEC at PI Ring 2 Ring 2 Call HIGH HIGH Keys OFF Keys OFF 505 ON 505 ON Back 10 30 OK Back 10 30 OK Use of the Tracker Ring Select the call tone type Call Set the call tone volume OFF tone disabled In case of a call the tracker will not emit any acoustic signal LOW tone with a low volume level HIGH tone with a high volume level Keys Enab
10. the previous set rate wms Set the accelerometer values Command wms 02 10 sensitivity O0 disables sensor 01 maximum Reply wms 02 10 OK 10 minimum Description timeout 01 99 minutes 02 sensitivity level 2 10 10 minutes timeout 38 Tracker Management by SMS Command Meaning and Values Example wgf Set the Geofence Case A status O disable 1 enable Command LAT1 LONG1 LAT2 LONG2z latitude and longitude wgf 1 45g937 7981N 008928 8012E for the 2 points defining the Geofence area 41937 8971 012928 8012 wgfz1 45937 7981N 008928 8012E 41937 8971N 012928 8012E Description 1 enable 45937 7981N 008928 8012E latitude and longitude of the first point 41937 8971N 012928 8012E latitude and longitude of the second point NOTE to enable or disable the Geofence function without setting the area sent the wgf command with the first field only Case B Command wgf 1 Reply wgf 1 Description 1 enables the function considering the previous defined area 39 Tracker Management by SMS Command Meaning and Values Example wanc Set the Anchor Case A enabling O disable 1 enable Command wanc 1 0100 radius 0050 0100 0200 0300 0500 0700 1000 Reply wanc 1 0100 OK 1500 2000 3000 4000 m default radius 0100 Description NOTE to set the tracker current position as area 1 enables center point send the complete wanc command
11. 10 minutes timeout rof Read the Geofence setup Command rgf status O2 disabled 1 enabled Reply LAT1 LONG1 LAT2 LONG2z latitude and 1 45037 7981 008028 8012 longitude of the 2 points which define the Geofence 41937 8971 012028 8012 area Description 1 enabled 45937 7981N 008928 8012E latitude and longitude of the first point 41937 8971N 012928 8012E latitude and longitude of the second point ranc Read the Anchor setup Command ranc status O disabled 1 enabled Reply ranc 1 0100 radius 0050 0100 0200 0300 0500 0700 1000 Description 1500 2000 3000 4000 m 1 enabled 0100 radius at 100 m 37 Tracker Management by SMS Writing Commands Command Meaning and Values Example wposc Set the cyclic position SMS in text format and the Case A relevant power save mode Command wposc 1 01 0 enabling O disable 1 enable Reply wposc 1 01 0 OK rate 01 99 minutes Description power save mode O disable 1 enable 1 enables the cyclic position SMS NOTE the power save mode works only with 01 1 minute rate SMS rate gt 5 minutes O disables the power save mode Never set like this 0 1 1 NOTE to enable or disable only the cyclic position Command wposc 1 SMS send the wposc command with the first Reply wposc 1 field only In this case the previously set rate is ats considered Description 1 enables the cyclic position SMS with
12. EIL EN NO POINT Selected point not set 20 Use of the Tracker Speed The Speed function allows to set a speed limit which when exceeded causes the emission of a progressive acoustic alarm more is the difference between the real speed and that programmed quicklier will be the alarm reproduction The Speed function is not available case of tracker compatible for OnTrack application mil EH EN EN 100 0090 i lkm h SPEED 100 0N ENABLE Home 10 30 O0K gt Back 10 30 ON Back 10 30 OFF 21 Use of the Tracker Setup HOW TO ENABLE THE CYCLIC POSITION SMS SENDING For further details on this function refer to the chapter Tracker Management by SMS paragraph Automatic Position Sending gt mi EH EN He A A OFF SETUP Tones GPRS rate OFF Memory V v Home 10 30 OK Back 10 30 OK Back 10 30 HER ON GPRS rate OFF GPRS rate OFF GPRS rate OFF Back 10 30 OK Back 10 30 OK gt Back 10 30 OK Use of the Tracker HOW TO SELECT THE RATE FOR CYCLIC GPRS CONNECTION E HHI mil E gt OFF Tones GPRS rate OFF
13. alarm SMS to the chapter Use of the Tracker preset phone number everytime it exits or chapter Tracker Management by SMS ri enters in a preset circular area Finder the tracker finds another tracker of the chapter Use of the Tracker same type and displays the direction and the distance to follow Guide the tracker finds a previously saved chapter Use of the Tracker destination point and displays the direction and the distance to follow Speed the tracker emits an acoustic alarm when chapter Use of the Tracker the preset speed limit has been overcome 11 Use of the Tracker Tracker Function Description Refer to Power Save Mode the tracker switches on off automatically to chapter Setup by MyTrack Software optimize the battery consumption Alarm SMS the tracker sends alarm SMS to the preset chapter Tracker Management by SMS phone number everytime a status change chapter Setup by MyTrack Software happens low battery memory full The tracker can work without the SIM card In this case all functions operating with GSM GPRS network will not be available Keypad Lock The keypad lock disables the keys to avoid accidental use of the tracker SOS It is possible to send an alarm message by means of pressing the SOS key even when the keypad lock is activated E HHI HHI sec sec Network Provider LOCK ED UNLOCK
14. area diagonal coordinates by means of the provided software or by means of an SMS command sent by a mobile phone To set the SMS command refer to the paragraph Reading and Writing SMS Commands After having set the parameters of the Geofence function the tracker will send an SMS message of alarm to the preset phone number set by means of the provided software each time it enters exits the pre established area or each time it is switched on outside the pre established area 32 Tracker Management by SMS Example of SMS message displayed on the mobile phone when the tracker enters the area GEO ID GLORIA GEOFENCE ENTER P0S 45937 9481N 008928 9992E ALT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone when the tracker exits the area GEO ID GLORIA GEOFENCE EXIT P0S 45937 9481N 008928 9992E ALT 0218m 07 04 10 10 09 The SMS message structure of the Geofence function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software GEOFENCE ENTER Alarm message POS Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm Alarm SMS The Alarm SMS are alarm messages sent if the function has been enabled by the provided software to a phone number every time that the tracker battery is almost discharged the tracker memory is full the GPRS network is
15. function is enabled without setting the radius the previously set coordinates for the central point and the last programmed radius will be considered If no radius was previously programmed by default it will be set to 100 m This function is programmable completely by SMS command wanc either operating directly on the tracker By the provided software only function enabling and radius setting is possible A Before enabling this function it is necessary to set the phone number where SMS will be sent by means of the provided software 31 Tracker Management by SMS Example of the SMS message displayed on the mobile phone when the tracker enters the area GEO ID GLORIA ANCHOR ENTER P08 45937 9481N 008928 9992E 4LT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone when the tracker exits the area GEO ID GLORIA ANCHOR EXIT POS 45937 9481N 008928 9992E 4LT 0218m 07 04 10 10 09 The SMS message structure of the Anchor function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software ANCHOR ENTER Alarm message POS wooo _ Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm Geofence The Geofence function allows to monitor the entry and the exit of the tracker in a pre established area This is a rectangular area and can be programmed by set the
16. rpos Reply A The tracker can reply in 3 different ways POS 41937 8283N 012928 8191E ALT 0262m DIR 023g SPEED 0050km h A POS data gt GPS position in real 8 09 07 05 26 15 56 time Reply B B LAST POS lt position data gt no GPS signal The LAST POS 45937 8283N reply message contains the last detected GPS data 008928 8191E ALT 0262m DIR 023g SPEED 0050km h C POS NO GPS DATA from the tracker switching SAT 09 07 05 26 15 56 on the GPS signal has not been detected Reply C POS GPS DATA NOTE the date and time refer to a SMS sending in case of Reply A Description last detected GPS data in case of Reply B 41937 8283 Lat in degree min 012928 8191 Long in degree min 0262m Altitude in m 023g Direction in degree 0050km h Speed in km h 09 Satellites number 07 05 26 Date 15 56 Time hhmm rposc Read cyclic position SMS setup and power save Command rposc mode status Reply rposc 1 01 0 status O disabled 1 enabled Description rate 01 99 minutes 1 enabled cyclic position SMS power save mode O disabled 1 enabled 01 1 minute rate O disabled power save mode 36 Tracker Management by SMS Command Meaning and Values Example rms Read the accelerometer setup values Command rms sensitivity O0 disabled sensor 01 maximum Reply rms 02 10 10 minimum Description timeout 01 99 minutes 02 sensitivity level 2 10
17. the instructions as explained in the product manual Only qualified personnel may install or repair this product Useonly approved accessories and batteries Do not use incompatible products The use of nonstandard products can cause damage to device and or people The batteries must be disposed according to the appropriate modes The consumer must duly hand in worn out batteries either at the appropriate collection points for the general public in his own town or wherever batteries of the same kind are sold compulsory warning according to law on the disposal of batteries The device is not water resistant keep it dry Contact with water or any other liquid could cause serious damage to the device General Information General Information The tracker is a portable device able to transmit its geographical location to a mobile phone or PC in real time Moreover the detected data can be recorded for further analysis The tracker is available in two different version LCD GPS tracker with display phone and 2MB data memory BOX GPS tracker without display without vocal communication and 512kB data memory Both trackers can be offered combined in the KIT version particularly indicated for the use of Finder function useful for real time locating This User Guide describes the tracker in the LCD version The tracker has three basic functions locating and transmitting its actual position sending an SOS me
18. S ALARM LAST P09 45937 9480N 008928 9992E 4LT 0218m 07 04 10 10 09 The SMS message structure of the SOS function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software SOS ALARM Alarm message POS wooo _ Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm 29 Tracker Management by SMS Tracker Management by SMS Position Request It is possible to ask for the tracker position by means of an SMS command After receiving the SMS command the tracker sends a message containing the position data to the phone number which sent the command To know the tracker position in real time send the following command POS For further details refer to the paragraph Reading and Writing SMS Commands Automatic Position Sending The tracker can send its own position at a programmable rate The automatic position sending can be carried out in two different modes by SMS by GPRS connection CYCLIC POSITION SMS The tracker can send an SMS message at intervals containing all the information on its current position This function is useful for monitoring the tracker motion at a distance by a mobile phone To use this function it is necessary to set using the provided software the phone number where the position messages will be sent setthe rate for cyclic
19. available the GPRS network is not available the GPS signal of the tracker has been lost the GPS signal of the tracker has been restored tracker motion is revealed the tracker motion stops 33 Tracker Management by SMS This function can only be programmed by means of the provided software Examp of the SMS message disp ayed on he mobi phone when the tracker battery is almost discharged GEO ID G Examp e of the SMS message disp LORIA LOW BATTERY 07 04 10 10 09 ayed on he mobi e phone when the tracker memory is full GEO ID G Examp e of the SMS message disp LORIA MEMORY FULL 07 04 10 10 09 ayed on he mobi e phone when he GPRS network is available GEO ID G Examp e of the SMS message disp LORIA GPRS 0K 07 04 10 10 09 ayed on he mobi e phone when he GPRS network is not available GEO ID GLORIA GPRS 0FE27 04 10 Examp e of the SMS message disp 10 09 ayed on he mobi e phone when here is GPS signal GEO ID G Examp e of the SMS message disp LORIA GPS FIX 0K 07 04 10 10 09 ayed on he mobi e phone when he GPS signal has been lost GEO ID G Examp e of the SMS message disp LORIA NO GPS FIX 07 04 10 10 09 ayed on he mobi e phone when a tracker motion is revealed GEO ID GLORIA MOTION 0N 07 04 10 10 09 Examp e of the SMS message disp ayed on he mobi e
20. c warning signal is emitted at SMS sending refer to the paragraph Setup This message also contains the current data on the location ifthe GPS signal has been revealed If there is no GPS signal coverage the last position data will be sent Backto previous page without disable the SOS sending Pressed for at least 2 sec disable the SOS sending ETT EN 505 Sending If SOS tone is enabled ELIT EN 508 Sent If SOS is sent EN GSM Signal missing SMS not sent Back Cancel 505 No or SMS center missing S0S not sent Back EN SMS error 505 not sent Back If there is no GSM signal f there is no SOS number or no SMS center number set If the previously set SMS center number is not correct Use of the Tracker If no numbers have been set or the absence of GSM signal every time the SOS key is pressed an acoustic warning signal is emitted In the event that there is no network service coverage the alarm functions may not be available Example of the SMS message displayed on the mobile phone with the detected current position data GEO ID GLORIA SOS ALARM P0S 45937 9480N 008928 9992E ALT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone with the last position data detected before the GPS signal loss GEO ID GLORIA SO
21. clic Position SMS function with SMS rate gt 5 minutes During the automatic switching on if the tracker is connected by the provided software the automatic switching off will be carried out after position SMS sending after carrying out all the preset operations and 2 minutes after tracker disconnection WITH CYCLIC GPRS CONNECTION CYCLIC GPRS CONNECTION Before using this mode enable and set the Cyclic GPRS Connection function with rate gt 5 minutes The tracker will switch off automatically after successfull GPRS connection and after carrying out all the preset operations If after two tries the GPRS connection is failed the tracker will switch off automatically 43 Setup by MyTrack Software To a set a Power Save Mode connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu Tracker Setup General 5 5 Recordings Guide General Tracker ID GEO PC Synchro Manual Real Time Clock 09 07 2009 15 11 23 Motion Sensor Sensitivity Mi Stop Timeout 1 min GPRS Connection Password Host IP Name Rate Disable Position SMS Motion Sensor Cyclic GPRS 44 Setup by MyTrack Software Alarm SMS To enable disable the Alarm SMS and set the phone number connect the tracker to the provi
22. ded software and access the setup window by selecting Setup from Remote Unit menu Tracker Setup Recordings Guide Alarm SMS Desinaton Phones Nea 4383401234567 Memory Full Position SM Enable Destination Phone Nr 393401 234567 Geofence amp Anchor Geofence Latitude Longitude ist 45 632383N 8 475395 Destination Phone Nr eS 393401234567 2nd 456305154 8 484438 View Anchor Destination Phone Nr 393401234567 Finder SMS Rate 155 45 Setup by MyTrack Software Position Data Recording To set a data position recording connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu Tracker Setup SMS Recordings Guide GPS Recordings Mode Rate Distance i Erase previous recordings Erase SMS Destination Nr 1 393401234567 SMS Destination Nr 2 SMS Destination Nr 3 SMS Destination Nr 4 46 Setup by MyTrack Software Update of the Tracker Firmware Version To update the tracker connect the tracker to the provided software and access the info window by selecting Info from Remote Unit menu Tracker Information Le 2 Tracker Information Information In
23. e PIN code by means of a mobile phone Inserting a SIM card any SMS message contained in it or which will be received in the future will be deleted and cannot be retriveable Sec If the battery is not inserted within 30 seconds the date and hour settings will be ERASED To insert the SIM card remove the back cover and lifting out the battery Preliminary Procedures How to Charge the Battery Before using the tracker for the first time the battery must be completely charged Before charging check that the network electrical supply corresponds to that of the battery charger Do not exceed the network voltage indicated on the battery charger A Use only batteries and battery chargers with the following features Battery model ABL 6C Li ion Battery charger model 20050050 Car charger model ESC 004 The manufacturing company is not liable for any damage to the tracker due to the use of accessories different from those expressly indicated Do not leave the tracker in particularly hot or cold environments during the battery charging Keep the tracker between 10 C and 40 C environmental temperature gt When the battery is almost discharged the tracker if emits an acoustic warning every minute Use of the Tracker Use of the Tracker Symbols Battery status EE Charged battery Discharged battery GPS signal coverage Maximum level WH
24. eriod The different Warranty Periods are 24 months for the device 6 months for the following consumable parts and accessories battery chargers headset device cover 90 days for the media on which any software is provided e g CD ROM DVD As far as national laws permit the warranty period will not be extended or renewed or otherwise affected due to subsequent resale repair or replacement of the Product authorized by the Manufacturer 50 2 21 Soas 523 id DL 23 qiy Go ol Eraus 1 Distributed by Cte international www cte it
25. eters BEC Set Limit Set Limit Lat 45 45 67N m Long 8 12 34E v v Back Center Back OK Back OK OI NEC Anchor Enabled Anchor Enabled Anchor Disabled Dist 45 m Dist 45m Dist Limit 50m Limit 50m Limit 50m av LE OFF AY av Back 10 30 K Back 10 30 0 99 Back 10 30 OK 16 Use of the Tracker Before enabling this function it is necessary to set the phone number where SMS will be sent by means of the provided software Example of the SMS message displayed on the mobile phone when the tracker enters the area GEO ID GLORIA ANCHOR ENTER P08 45937 9481N 008328 9992E 4LT 0218m 07 04 10 10 09 Example of the SMS message displayed on the mobile phone when the tracker exits the area GEO ID GLORIA ANCHOR EXIT POS 45937 9481N 008928 9992E 4LT 0218m 07 04 10 10 09 The SMS message structure of the Anchor function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software ANCHOR ENTER Alarm message POS oss Latitude and longitude of the geographical position ALT Altitude in m Event date and time yy mm dd hh mm 17 Use of the Tracker Finder The Finder mode allows to find another tracker of the same type LCD or BOX version by display
26. formation GEOPOINT GEOPOINT STD STD Geo Gloria Geo Gloria Serial Number XLUTH3001 Serial Number XLUTH3001 Firmware Release 1 04 Firmware Release 1 04 Year 2007 Year 2007 Memory 2MB Memory 2MB Status Ready A new window is opened for update selection During tracker firmware upgrade on the tracker will be displayed UPGRADE Please don t turn OFF the device Wait until the update is completed this occurs when the tracker is turned off If the tracker to be updated is connected with GSM GPRS network be sure that the GSM GPRS network signal level is high If the tracker to updated is connected by USB cable do not remove the cable during the update A To perform the update it is necessary to connect the provided battery charger to the tracker 47 Maintenance Maintenance The tracker and relevant accessories must be handled with care Read the following instructions carefully Clean the tracker with a soft cloth avoiding the use of corosive chemical products solvents or aggressive detergents Do not paint the tracker Do not swallow the accessories or small components of the tracker Avoid blows to the tracker which could internally damage the product Do not open the tracker in any way differently from the way indicated in the manual Do not wet the tracker Humidity condensation rain or any other liquids containing mineral substances could damage the electronic circui
27. ing the distance and the direction to follow The Finder function can only be used if the distance between the trackers is less than 999 Km A A To carry out the Finder function set the communication rate by the provided software The necessary motion for updating the relevant position must be no less than 10 meters in 3km h More motion means more precise indication of direction It is important to keep the tracker pointing in the direction used for reference In every way if change of direction is inevitable e g the ground is not viable on approaching the correspondent the direction will be constantly updated and corrected by the tracker 18 PHONE BOOK uni NEC uui A A 350 Dest Mary Mary m A 45 12 34N FI N D E R 3123456789 Long 08 12 34 v v Dist 350m Home 10 30 OK Back 10 30 OK Back Detail Back 10 30 253 gt eu Retry Numbers in the PHONE Book Yes 10 30 Absence of GSM or GPS signal Selected Back voice not corresponding to a tracker Use of the Tracker Guide The Guide function allows to reach a destination point by displaying the distance and direction The Guide function is available only if the distance between the tracker and destination point is less than 999 Km It is possible to set the Guide functi
28. le disable the keys tone SOS Enable disable the acoustic signal tone for the SOS key RECORDINGS The tracker allows to record the detected events automatically without setting the recording the position data to review the track afterwords if the recording was previously set The tracker can records approx 70 000 position points and approx 1 900 events When an event occurs the tracker detects it and start to record in the Event LOG The following list shows all the events which can be detected and recorded automatically by the tracker GPS signal available unavailable entry exit from Geofence area entry exit from Anchor area firmware update SOS alarm memory erasing roaming on off network GSM provider changing if roaming on power on off low battery making or receiving a voice call receiving a data call making a GPRS hanging up a call motion on off GSM network available unavailable 25 mil EN SETUP v Home 10 30 gt Tones Memory v Back 10 30 OK EN Distance Mode Erase Back 10 30 EN Distance Mode Erase Back 10 30 Use of the Tracker 5 Memory v Back 10 30 OK EN Distance Mode OFF Erase 10 30 OK ee ae 0 Distance 0 OFF Mode OFF Erase 0
29. on by means of the provided software or directly on the tracker 3D FIX suggested to save the destination point when the GPS signal level is optimal In case of weak GPS signal the accuracy of destination point coordinates will not be guaranteed HOW TO SAVE A DESTINATION POINT MAX 30 POINTS OI 01 Em sec Save As 02 Dest Point 01 GUIDE GE Lat 45 12 34N v 04 v Long 08 12 34E Home 10 30 OK Back OK Yes 10 30 i et A 122 eco Overwrite Data 03 04 v Back OK j Yes 10 30 Use of the Tracker HOW TO REACH A DESTINATION POINT A The necessary motion for updating the relevant position must be no less than 10 meters in 3km h More motion means more precise indication of direction It is important to keep the tracker pointing in the direction used for reference In every way if change of direction is inevitable e g the ground is not viable on approaching the correspondent the direction wil be constantly updated and corrected by the tracker NEC NEC A 01 I A 350 Dest HOME 02 m Lat 45 12 34N G U I D E pou Long 08 12 34E v 04 v Dist 350m Home 10 30 OK Back OK Back Detail Back 10 30 No GPS Signal
30. phone when tracker motion stops GEO ID GLORIA MOTION 0FEQ7 04 10 10 09 34 Tracker Management by SMS The SMS message structure of the Alarm SMS function is described here below GEO Tracker type ID Tracker name preset by the user through the provided software LOW BATTERY Alarm message Event date and time yy mm dd hh mm Reading and Writing SMS Commands The SMS commands allows to set or read some tracker settings These messages can be sent by a mobile phone or by a GSM device able to send receive SMS i e a GSM modem When the tracker is switched ON and there is GSM signal it can receive any SMS command If the tracker receives a correct SMS command an answer is sent to the SMS command sender If the message contains invalid characters the tracker will not reply If it contains invalid values the tracker will reply a message containing COMMAND ERROR All commands start with the letter r reading or w writing Ensure that the SMS commands are written exactly shown the table Any change space capital letter small letter could affect the recognition of the command zl Before enabling the sending of position SMS in cyclic mode wposc ensure that the SMS phone number has been programmed 35 Tracker Management by SMS Reading Commands Command Meaning and Values Example rpos Read instantaneous GPS position data Command
31. position SMS using the provided software or sending an SMS command enable the function using the provided software or sending an SMS command 30 Tracker Management by SMS CYCLIC GPRS CONNECTION The cyclic GPRS connection allows to connect the tracker automatically at a programmed rate for the continuous position updating At the programmed rate the tracker will be connected only for the time needed for sending the position point This function is very useful if combined with the I Scout web server as it allows to display the detected positions by every station connected to internet To use this function it is necessary to set the GPRS parameters using the provided software or sending an SMS command e enable the function setting the rate for the cyclic GPRS connection using the provided software Anchor The Anchor function allows to monitor within a pre established circular area the position of a person an object or an animal When the tracker detects the exiting from the pre established area or the ri entering it sends an alarm SMS containing its position data to the preset phone number This function is programmable using the complete SMS command enabling and radius setting either operating directly on the tracker or partially by the provided software When the complete SMS command is received by the tracker e g wanc 1 0500 the function is enabled and the current tracker position is considered as area central point If the
32. r The Manufacturer assumes no responsibility for any errors or incoherence possibly contained in this manual Printed in Italy Note for the users of appliances According to the article 13 of the Legislative Decree no 151 dated July 25 2005 Enforcement of the 2002 95 EC and 2003 108 EC directives relavant to the reduction of dangerous substances in electric and electronic applinaces as well as waste disposal the symbol of a crossed dustbin applied on appliances or on their cases means that the product at the end of its life cycle must be disposed in a dedicated location than other waste The user must therefore dispose the aplliance at its end of life in the relevant disposal site for electric and electronic waste or give it back to resellers at the time of purchasing a news equivalent one The correct disposal and consequant start up of a recycling of the unused appliance treatment and final disposal compatible to the enviroment concurs to avoid possible negative effects on the enviroment and health and favours the reusing and or recycling of the parts making the apparatus The abusive disposal of such products done by users is fined according to the present legislation Contents P ormatioi reliminary Procedures Inserting the SIM Card How to Charge the Battery Position Request Automatic Position Sending Geofence Alarm SMS Reading and Writing SMS Commands
33. se of the Tracker NEC i 1 John Mary 3123456789 3123456789 V v v Home 10 30 OK Back Call Back Call RECEIVING A CALL Er H ee Incoming Call 00 05 1123456789 Reject Answer Hungup Back K During the transfer of data between the tracker and PC it is not possible to make or receive any calls SIM card in use However the information contained in it except for SMS The tracker does not allow to use the phone book possibly memorized on the messages saved a mobile phone will not be erased 15 Use of the Tracker Anchor The Anchor function allows to monitor within a pre established circular area the position of a person an object or an animal When the tracker detects the exiting from the pre established area or the ri entering it sends an alarm SMS containing its position data to the preset phone number This function is programmable either operating directly on the tracker or by the provided software or by sending an SMS command ETT EN TII PLIN centre to be monitored Anchor Disabled an ANCHOR Dist 11103111 Limit 100m NW m Max 5 v MM Home 10 30 08 5 Torna 10 30 OK Available values 50 100 200 300 500 700 1000 1500 2000 3000 4000 m
34. ssage in case of an emergency voice communication as a mobile phone The tracker is provided with MyTrack software allowing the tracker management and personal tracking A The GPS receiver and the GSM device work at higher radio frequencies which can be stopped by enclosures containing metal and plastic parts It is suggested to keep the tracker under light clothes as external as possible Examples of shielding materials kevlar carbon fibre some polyurethanic and polyamidic resins especially if black etc Examples of materials which cannot influence the radio waves ABS ABS PC policarbonate etc For further details on tracker use and functions please read carefully the user manual complete version contained the enclosed CD ROM DISPLAY MICROPHONE MULTIFUNCTION KEYS General Information ENTER OWN SCROLL PUSH FUNCTION FUNCTION SOS KEY USB DC IN HEADSET Preliminary Procedures Preliminary Procedures Inserting the SIM Card In case of a SIM card prepaid the communication between the tracker and the provided software is made exclusively by SMS text or GPRS network with subscription the communication between the tracker and the provided software is made by SMS text GPRS network or also sending receiving data only if the data number has been activated by the network provider Before inserting the SIM card the tracker disable th
35. ts In the event of contact with liquids remove the battery and leave the tracker to dry Do not use or leave the tracker in particularly hot environments High temperatures could damage the electronic circuits the battery and the plastic parts of the tracker Do not use or leave the tracker in particularly cold environments Low temperatures could cause damage to the electronic circuit boards of the tracker Do not use or leave the tracker in particularly dirty or dusty environments the tracker could get damaged 48 Technical Features Technical Features GPS receiver SiRFstarlll 20 channels GSM frequencies 850 900 1800 1900 MHz Data memory 2MB non volatile FLASH Porta di comunicazione no 1 USB Sensor no 1 for accelerometer Dimension Weight 74 x 74 x 23 mm 120 gr Battery model ABL 6C Li ion 3 7V 1000mAh Battery charger model ZDO50050EU input 100VAC 240V 50 60Hz 0 15A output 5VDC 500mA Car charger model ESC 004 input 13 6VDC output 5 500mA Conformity CE mark CONDITION BATTERY LIFE Standby mode with motion sensor active 10 days Tracking SMS every minute GPS always on 9 hours Tracking SMS every 5 minutes GPS with hotstart 4 days Continuous tracking 2 hours Data connection with GPS system continuously active 2 hours Position data recording every minute 37 hours Tracker not in use 2 days Tracker in communication on GSM network 4 hours
Download Pdf Manuals
Related Search